Home › Engine / Hybrid System › 3UR-FE ENGINE MECHANICAL › ENGINE ASSEMBLY
RM27L0U _51 Engine / Hybrid System _049296 3UR-FE ENGINE MECHANICAL _0235566 ENGINE ASSEMBLY A

3UR-FE ENGINE MECHANICAL  ENGINE ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

Perform "Inspection After Repairs" after replacing the engine assembly, cylinder head LH, Cylinder head sub-assembly, No.1 camshaft, No. 2 camshaft, No. 3 camshaft, No. 4 camshaft, camshaft timing gear, camshaft timing exhaust gear (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).


PROCEDURE

Hide 1.REMOVE ENGINE STAND

a.
U151520

Install the 2 engine the hangers with the 2 bolts as shown in the illustration.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
Item Part No.
Engine hanger 12281-38150
Bolt 90119-A0166



b.

Attach an engine sling device and hang the engine with a chain block.


c.

Remove the bolts and engine assembly from the engine stand.


Hide 2.INSTALL ENGINE ASSEMBLY

a.

Slowly lower the engine assembly into the engine compartment.

NOTICE:

Make sure that the engine is clear of all wiring and hoses.



b.

Attach the engine mounting insulators to the vehicle.


c.
A163780E06
0.104,0.104 0.417,0.51 0.313,0.406 10 true RH: 0.115,2.354 0.417,2.771 0.302,0.417 10 true LH:

Install the 4 engine mounting insulator bolts.

Torque:
79 N*m (806 kgf*cm, 58 ft.*lbf)


d.

Remove the 2 bolts and 2 engine hangers.


Hide 32907A 3.INSTALL OIL COOLER TUBE

a.

Install the oil cooler tube with the bolt.

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)


Hide 16268 4.INSTALL NO. 1 WATER BY-PASS PIPE

a.
A183283

Connect the hose and install the water by-pass pipe with the 2 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 32101 5.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

a.
A163778E01
0.9,1.607 1.201,1.763 0.302,0.156 10 SST 0.831,1.237 1.049,1.572 1.049,1.572 1.089,1.108 false

Using SST, hold the crankshaft.

SST
09213-70011  
09330-00021  


b.
A217514C02
0,0 0,0 false
V100135

Engine Side


Install the crankshaft angle sensor rotor.

HINT:
·

Align the pin hole of the crankshaft angle sensor rotor with the pin of the crankshaft.

·

As the crankshaft angle sensor rotor is not reversible, be sure to install it so that it is facing in the direction shown in the illustration.




c.
A217515C02
1.865,3.385 2.625,3.125 2.625,3.125 2.76,3.125 false 1.177,0.417 1.76,0.25 1.76,0.25 1.896,0.25 false 1.958,0.177 2.271,0.333 0.313,0.156 10 false *1 2.844,3.042 3.156,3.198 0.313,0.156 10 false *2
*1 Drive Plate
*2 Rear Drive Plate Spacer
V100135

Automatic Transmission Side


Install the drive plate and rear drive plate spacer onto the crankshaft.

HINT:

As the rear drive plate spacer and the drive plate are not reversible, be sure to install them so that they are facing in the direction shown in the illustration.



d.

Install the drive plate and ring gear and bolts.

HINT:

The bolts are tightened in 2 progressive steps.


i.

Clean the bolts and bolt holes.


ii.
A380777C01
1.833,1.188 2.052,0.479 2.052,0.479 2.198,0.479 false 2.26,0.406 2.573,0.563 0.313,0.156 10 false *1
*1 Adhesive


Apply adhesive to 2 or 3 threads of the 8 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



iii.
A214574E02
1.49,0.448 1.594,0.594 0.104,0.146 10 true 9 1.844,0.448 1.938,0.604 0.094,0.156 10 true 1 1.5,1.625 1.594,1.802 0.094,0.177 10 true 2 2.25,1.052 2.365,1.198 0.115,0.146 10 true 3 1.094,1.031 1.188,1.188 0.094,0.156 10 true 4 2.188,1.375 2.302,1.521 0.115,0.146 10 true 5 1.167,0.708 1.281,0.865 0.115,0.156 10 true 6 2.177,0.719 2.302,0.875 0.125,0.156 10 true 7 1.167,1.375 1.26,1.521 0.094,0.146 10 true 8 1.813,1.625 1.99,1.771 0.177,0.146 10 true 10

Step 1:

Install and uniformly tighten 10 new bolts in the sequence shown in the illustration.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)

NOTICE:
·

Do not reuse the drive plate installation bolts.

·

Do not strike or damage the drive plate installation bolts. Be sure to handle them carefully.




iv.

Mark the top of each drive plate installation bolt with paint.


v.

Step 2:

Tighten the drive plate installation bolts 90° as shown in the illustration.


vi.

Check that the painted marks are now at a 90° angle to the top.

NOTICE:

Do not start the engine for at least an hour after installing the drive plate.




Hide 6.INSTALL EXHAUST MANIFOLD

Hide 27020 7.INSTALL GENERATOR ASSEMBLY

a.

Hide 88320 8.INSTALL COOLER COMPRESSOR ASSEMBLY

Hide 17342 9.CONNECT NO. 2 AIR INJECTION SYSTEM HOSE

Hide 17343 10.CONNECT NO. 3 AIR INJECTION SYSTEM HOSE

Hide 82121 11.INSTALL ENGINE WIRE

a.
A163790

Connect the 2 connectors and 2 clips to the engine room junction block.


b.

Install the engine wire with the nut. Then connect the 2 clips.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.

Connect the 4 air injection control driver connectors.


d.

Install the ground wire with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


e.

Connect the cable to the positive (+) battery terminal.


f.

Install the wire to the positive (+) battery cable with the nut.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


g.
A163791

Connect the 2 air injection system hoses.


h.

Install the ground wire with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


i.

Connect the 2 air pump connectors and install the connector bracket with the nut.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


j.
U151465

Connect the 4 connectors to the connector holder block.


k.

Connect the heater hoses.


Hide 89661 12.INSTALL ECM

a.
A183281

Connect the ECM connector and clamp.

HINT:

Refer to the following procedures to connect the ECM connector (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>ECM>INSTALLATION).



Hide 23801P 13.CONNECT FUEL MAIN AND RETURN HOSE

a.
U153138

Connect the fuel main and return hoses (See page Engine / Hybrid System>3UR-FE FUEL>FUEL SYSTEM>PRECAUTION).


b.

Install the fuel pipe clamp.


Hide 23820 14.CONNECT FUEL VAPOR FEED HOSE ASSEMBLY

a.
A183280

Connect the purge line hose.


Hide 44750 15.CONNECT VACUUM HOSE ASSEMBLY

a.
A183279

Connect the union to check valve hose.


Hide 87246C 16.CONNECT OUTLET HEATER WATER HOSE C

Hide 87245C 17.CONNECT INLET HEATER WATER HOSE C

Hide 17880 18.INSTALL AIR CLEANER HOSE ASSEMBLY

Hide 35000 20.INSTALL AUTOMATIC TRANSMISSION ASSEMBLY (for 2WD)

Hide 35000 21.INSTALL AUTOMATIC TRANSMISSION ASSEMBLY (for 4WD)

Hide 16400 22.INSTALL RADIATOR ASSEMBLY

a.

Install the radiator assembly (See page Engine / Hybrid System>3UR-FE COOLING>RADIATOR>INSTALLATION).


Hide 25.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

Hide 26.INSPECT FOR OIL LEAK

Hide 55701J 30.INSTALL COWL TOP OUTER PANEL SUB-ASSEMBLY

a.
A183287

Install the outer panel with the 7 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


b.

Connect the 2 washer hoses.


Hide 85110 31.INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY

a.

Install the windshield wiper motor (See page Vehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>INSTALLATION).


Hide 53301 32.INSTALL HOOD SUB-ASSEMBLY

a.
A160840

Install the hood with the 4 bolts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


b.

Attach the lower part of the 2 hood supports to the hood support bolt ball joints.

NOTICE:

Install the hood support while supporting the hood by hand.



c.

Attach the hood support clips.

NOTICE:

Check that the hood support is engaged in the ball joint and that it cannot be pulled out.



Hide 53301 33.ADJUST HOOD SUB-ASSEMBLY