Home › ENGINE ยท 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P1604    Startability Malfunction

for Preparation Click here


DESCRIPTION

This DTC is stored when the engine does not start even though the STA signal is input or when the engine takes a long time to start, and when the engine speed is low or the engine stalls just after the engine starts.
Using the Techstream, the conditions present when the DTC was stored can be confirmed by referring to the freeze frame data. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.
It is necessary to check if the vehicle ran out of fuel before performing troubleshooting, as this DTC is also stored when there is engine starting trouble due to running out of fuel.

DTC No.
DTC Detection Condition
Trouble Area
P1604
Either condition is met:
  1. The engine speed is less than 500 rpm with the STA signal on for a certain amount of time (refer to the illustration below) (1 trip detection logic).
  2. After the engine starts (engine speed is 500 rpm or more), the engine speed drops to 200 rpm or less within approximately 2 seconds (1 trip detection logic).
  1. Engine immobiliser system
  2. Engine assembly (excess friction, compression loss)
  3. Starter assembly
  4. Crankshaft position sensor
  5. VVT sensor
  6. Engine coolant temperature sensor
  7. Fuel pump
  8. Fuel pump control system
  9. Fuel pipes
  10. Fuel line
  11. Fuel injector assembly
  12. Throttle with motor body assembly
  13. Fuel pressure regulator assembly
  14. Battery
  15. Drive plate and ring gear sub-assembly*1
  16. Flywheel sub-assembly*2
  17. Spark plug
  18. Ignition coil circuit
  19. Intake system
  20. Camshaft timing oil control valve assembly
  21. Mass air flow meter sub-assembly
  22. Air fuel ratio sensor
  23. Valve timing
  24. Fuel
  25. Purge VSV
  26. Intake valve
  27. ECM
  1. *1: for Automatic Transmission
  2. *2: for Manual Transmission

A220316E02


Reference waveforms showing a normal cold engine start

A226238E01


Reference waveforms showing a normal warm engine start

A226237E01


Reference values when there is an air leak in the intake system during starting difficulty

A264217


WIRING DIAGRAM

Refer to DTC P0031 .
Refer to DTC P0335 .
Refer to DTC P0351 .
Refer to DTC P0451 .
Refer to Fuel Pump Control Circuit .
Refer to Fuel Injector Circuit .

INSPECTION PROCEDURE

HINT:
  1. In contrast to normal malfunction diagnosis for components, circuits and systems, DTC P1604 is used to determine the malfunctioning area from the problem symptoms and freeze frame data when the user mentions problems such as starting difficulty.
    As these DTCs can be stored as a result of certain user actions, even if these DTCs are output, if the customer makes no mention of problems, clear these DTCs without performing any troubleshooting and return the vehicle to the customer.
  2. If any other DTCs are output, perform troubleshooting for those DTCs first.
  3. When the Data List item "Immobiliser Fuel Cut" is ON, the engine cannot be started.
  4. Read freeze frame data using the Techstream. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.
  5. When confirming the freeze frame data, be sure to check all 5 sets of freeze frame data (Click here).
  6. When confirming freeze frame data, if there are multiple items related to the cause of the malfunction, perform troubleshooting for all related items.
  7. Try to start the vehicle under the conditions recorded in the freeze frame data which were present when the malfunction occurred. Confirm the data at this time and compare it with the freeze frame data.
  8. If the malfunction does not reoccur, carefully check the vehicle conditions from when the malfunction occurred using freeze frame data.
  9. When performing inspections, jiggle the relevant wire harnesses and connectors in an attempt to reproduce malfunctions that do not always occur.
  10. If the same inspection or replacement procedure appears 2 times when performing an inspection procedure, it is not necessary to repeat the procedure the second time.


Malfunction Recurrence and Inspection Areas
  1. Freeze frame data exists, but the malfunction (starting difficulty) has not reoccurred and the malfunction conditions are unknown.

    1. The engine speed recorded in the freeze frame data is 0 rpm (the engine does not crank).

      HINT:
      One of the following problems may be present: battery depletion, excess engine friction, a starter malfunction or a crankshaft position sensor malfunction.

      1. If the battery voltage is less than 6 V during cranking, there is a high probability that engine friction is abnormal.
      2. If the battery voltage drops to 5 V or less when starting the engine, the battery may be malfunctioning.

      3. If the battery voltage fluctuates while cranking the engine, it can be concluded that cranking is being performed. When the engine speed is 0 rpm, the crankshaft position sensor and/or ECM may be malfunctioning.


        A215383E23

    2. All engine speeds recorded in the freeze frame data are between 60 and 250 rpm (the engine cranks but there is no combustion).

      HINT:
      If the engine speed is between 60 and 250 rpm (no initial combustion), there may be a wiring problem or a complete failure of an ignition or fuel system part.


      1. Due to an engine coolant temperature sensor malfunction, the fuel injection volume is extremely high or low and the engine may not be able to be started.


        A215384E30

    3. The engine speed recorded in the freeze frame data is 250 rpm or higher (the initial combustion and starter turnoff timing is too late).

      HINT:
      If the engine speed is 250 rpm or higher (combustion occurs but the initial combustion and starter turnoff timing is too late), the fuel injection volume is often incorrect (too low or too high) and determining the cause of the malfunction is often difficult.

      1. Due to an engine coolant temperature sensor malfunction, the fuel injection volume is extremely high or low and engine starting trouble may occur.
      2. If Long FT is incorrect, there may be a fuel supply problem due to the injectors or fuel pump being clogged, etc.

      3. If the engine cranking speed is too high, compression loss may have occurred due to carbon interfering with the valve operation.


        A215383E24

  2. When the malfunction (starting difficulty) can be reproduced, or malfunction conditions are known, perform the following inspections ("Problem Symptoms" and "Systems to Inspect").

    1. Problem Symptoms

      1. The engine does not crank.

        HINT:
        The starter is normal if a noise that indicates the starter pinion gear is extending is heard. The battery may be fully depleted or there may be excess engine friction.

      2. The engine cranking speed is abnormal.

        HINT:
        If the engine cranking speed is too high (for example, 300 rpm or higher with no combustion), compression loss may have occurred because carbon interfered with valve operation, etc.

      3. There is no initial combustion.

        HINT:
        If there is no initial combustion, there is probably a wiring problem or an ignition or fuel system part malfunction.

      4. The engine stalls after starter turnoff.

        HINT:
        If the engine stalls after starter turnoff, the air-fuel ratio may be incorrect or the VVT may have a problem returning.

      5. The initial combustion and starter turnoff occur late.

        HINT:
        If the initial combustion and starter turnoff occur late, the fuel injection volume is probably incorrect (too low or too high).

        HINT:
        Causes of fuel system malfunctions according to conditions present at the time of the malfunction.
        1. When 2 to 3 minutes have elapsed after stopping the engine: Fuel pressure loss due to the fuel pressure regulator assembly failing to maintain the fuel pressure.
        2. When 15 to 120 minutes have elapsed after stopping the engine: Problem with injector fuel seal.
        3. When a long time has elapsed after stopping the engine: Fuel pressure regulator assembly is stuck open.

    2. Systems to Inspect

      1. Intake system
      2. Ignition system
      3. Fuel system


INSPECTION FLOW
  1. Freeze frame data exists, but the malfunction (starting difficulty) has not reoccurred and the malfunction conditions are unknown.

    Freeze Frame Data Item
    Result
    Suspected Area
    Procedure
    Engine Speed
    0 rpm (no engine cranking at all)
    1. Battery fully depleted
    2. Engine assembly (excess friction)
    3. Starter assembly
    4. Engine immobiliser system
    5. Crankshaft position sensor
    6. ECM
    4 to 9
    60 to 250 rpm (engine cranks but no initial combustion*1)
    1. Fuel pump control circuit
    2. Ignition system
    3. Engine coolant temperature sensor
    4. Fuel injection system
    10 to 14
    250 rpm or higher (combustion occurs but initial combustion and starter turnoff*2 occur late)
    1. Engine assembly (compression loss)
    2. Fuel injection system
    3. Fuel pump control system
    15 to 23

    HINT:
    1. *1: First combustion after cranking begins.
    2. *2: Condition when engine speed increases and starter can be turned off.

  2. When the malfunction (starting difficulty) can be reproduced, or when malfunction conditions are known.

    1. Problem Symptoms

      Problem Symptom
      Suspected Area
      Suspected Component
      Procedure
      The engine does not crank
      Battery malfunction
      1. Battery fully depleted
      26 to 31
      Starting system
      1. Starter assembly (includes pinion gear wear or tooth damage)
      2. Starting system
      Engine assembly
      1. Engine assembly (excess friction)
      2. Drive plate and ring gear sub-assembly wear or tooth damage*1
      3. Flywheel sub-assembly wear or tooth damage*2
      Cranking speed too low
      Battery malfunction
      1. Battery fully depleted
      32 to 34
      Starting system
      1. Starter
      Engine assembly
      1. Engine assembly (excess friction)
      Cranking speed too high
      Engine assembly
      1. Engine assembly (compression loss)
      There is no initial combustion
      Fuel supply problem
      1. Cannot maintain pressure due to fuel pressure regulator assembly malfunction
      2. Fuel injector assembly leak
      3. Fuel leak from fuel line
      4. Fuel pump control system
      5. Fuel pump
      35 to 49
      Engine immobiliser system
      Engine immobiliser system
      Ignition system malfunction
      1. Spark plug
      2. Crankshaft position sensor
      3. Ignition coil assembly
      Engine stalls after starter turnoff
      Air suction
      1. Intake system connections
      50 to 55
      Deposits in throttle with motor body assembly
      1. Throttle with motor body assembly
      VVT valve does not return properly
      1. Camshaft timing oil control valve assembly
      Mass air flow meter sub-assembly malfunction
      1. Mass air flow meter sub-assembly
      The initial combustion and starter turnoff occur late
      Engine coolant temperature sensor malfunction
      1. Engine coolant temperature sensor
      56 to 69
      Mass air flow meter sub-assembly malfunction
      1. Mass air flow meter sub-assembly
      Abnormal air fuel ratio learned value
      1. Air fuel ratio sensor
      Deviation from fuel injection characteristics
      1. Fuel injector assembly
      Wet-fouled or dry-fouled spark plug
      1. Spark plug
      Lack of fuel pressure
      1. Fuel pressure regulator assembly
      2. Fuel pump
      3. Fuel pump control system

      1. *1: for Automatic Transmission
      2. *2: for Manual Transmission

    2. Systems to Inspect

      Troubleshooting by System
      Suspected Area
      Suspected Component
      Procedure
      Fuel system troubleshooting A
      Abnormal air fuel ratio learned value
      1. Fuel injector assembly
      85 to 92
      93 to 100
      Rough idling
      1. Crankshaft position sensor
      Abnormal fuel pressure
      1. Fuel
      2. Fuel leak from fuel line
      3. Fuel pump
      4. Fuel pressure regulator assembly
      Fuel system troubleshooting B
      Abnormal concentration of HC in surge tank
      1. Purge VSV system
      2. Fuel injector assembly
      101 to 103
      Fuel system troubleshooting C
      Injection signal system malfunction
      1. Fuel injector assembly
      2. Crankshaft position sensor
      3. VVT sensor
      4. ECM
      71 to 75
      Intake system troubleshooting
      Difference between ISC target value and opening angle when idling
      1. Engine assembly (compression loss)
      2. Valve timing
      3. Engine coolant temperature sensor
      4. ECM
      82 to 84
      104 to 106
      Ignition system troubleshooting
      Camshaft and/or crankshaft position sensor signal malfunction
      1. Crankshaft position sensor system (including sensor installation)
      2. VVT sensor system (including sensor installation)
      3. ECM
      76 to 81
      107 to 112

NOTICE:
  1. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  2. After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).

1.CHECK FOR ANY OTHER DTCS OUTPUT AND RECORD FREEZE FRAME DATA
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.



    A103809E53
  1. Read the DTCs and record the freeze frame data.

    HINT:
    1. This freeze frame data shows the actual engine conditions when engine starting trouble occurred.
    2. When confirming the freeze frame data, be sure to check all 5 data sets of freeze frame data.
    3. The fourth set of freeze frame data is the data recorded when the DTC is stored.

    Result 
    Result
    Proceed to
    DTC P1604 is output
    A
    DTC P1604 and other DTCs are output
    B



B
GO TO DTC CHART (Click here)
A


2.CHECK ENGINE IMMOBILISER SYSTEM
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Immobiliser Fuel Cut.

  1. Read the value displayed on the Techstream.

    OK:
    Immobiliser Fuel Cut is OFF.

    HINT:
    If the engine is cranked immediately after reconnecting the battery cable (key verification for engine immobiliser system not completed), the engine cannot be started. Key verification needs to wait for several seconds after turning the ignition switch to ON.



NG
REPAIR ENGINE IMMOBILISER SYSTEM (Click here)
OK


3.CHECK MALFUNCTION CONDITION
  1. Confirm the problem symptoms.

    Result 
    Result
    Proceed to
    Freeze frame data exists, but the starting difficulty cannot be reproduced and it is unknown what kind of starting difficulty occurred
    A
    The problem symptoms can be reproduced, or the malfunction conditions are known
    B



B
Go to step 25
A


4.READ FREEZE FRAME DATA
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Using the Techstream, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).

    Result 
    Freeze Frame Data Item
    Suspected Area
    Proceed to
    Engine Speed
    Battery Voltage
    All 5 sets of freeze frame data are 0 rpm (no engine cranking at all)
    Minimum voltage is below 5 V
    Battery fully depleted
    A
    Minimum voltage is 5 V or higher
    1. Starter malfunction
    2. Crankshaft position sensor system
    3. Excess engine friction
    4. ECM
    B
    60 to 250 rpm (engine cranks but no initial combustion)
    -
    1. Fuel pump control system
    2. Ignition system
    3. Engine coolant temperature sensor
    4. Engine immobiliser system
    5. Fuel injection system
    C
    250 rpm or higher (combustion occurs but initial combustion and starter turnoff occur late)
    -
    1. Engine assembly
    2. Fuel injection system
    3. Fuel pump control system
    D

    Result 
    Freeze Frame Data Item
    Suspected Area
    Proceed to
    Low Rev for Eng Start
    ON exists
    1. Intake system connections
    2. Throttle with motor body assembly
    3. Camshaft timing oil control valve assembly
    4. Mass air flow meter sub-assembly
    E

    HINT:
    When DTC P1604 is stored, either "Engine Start Hesitation"*1 or "Low Rev for Eng Start"*2 in the freeze frame data will be ON. If "Low Rev for Eng Start" is ON, proceed to E.
    *1: This value turns ON when the engine speed does not reach a certain value for a certain period of time when starting the engine.
    *2: This value turns ON when the engine stalls immediately after starting the engine. If "Low Rev for Eng Start" is ON, as there is a possibility that the low engine speed or engine stall was caused by the user, confirm the following freeze frame data items.
    1. Immobiliser Fuel Cut
    2. Engine Speed (starter off)
    3. Shift SW Status (R, D)



B
Go to step 5

C
Go to step 10

D
Go to step 15

E
Go to step 50
A

CHARGE OR REPLACE BATTERY 

5.READ FREEZE FRAME DATA
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Using the Techstream, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).

    Result 
    Freeze Frame Data Item
    Result
    Suspected Area
    Proceed to
    Battery Voltage
    Minimum voltage is 6 V or higher and voltage does not fluctuate*1
    Starter system
    A
    Minimum voltage is 6 V or higher and voltage fluctuates*2, *3
    1. Crankshaft position sensor system
    2. ECM
    B
    Minimum voltage is 5 to 6 V*4
    1. Excess engine friction
    2. Battery fully depleted
    C

    HINT:

    1. A217930E01
      *1: The 5 sets of freeze frame data show approximately the same battery voltage.
    2. *2: The 5 sets of freeze frame data show different battery voltages.
    3. *3: If the voltage fluctuates, it can be determined that cranking is being performed. When the engine speed is 0 rpm, the crankshaft position sensor system and/or the ECM may be malfunctioning.
    4. *4: There may be excess engine friction. Make sure that the crankshaft rotates smoothly when turning it by hand. Excess engine friction may have occurred temporarily. Remove the cylinder head cover and oil pan, and check for foreign matter such as iron fragments. If there is a malfunction or signs of a malfunction present, perform a detailed inspection by disassembling all the parts.



B
Go to step 6

C
CHECK AND REPAIR ENGINE OR BATTERY
A

CHECK STARTER SIGNAL CIRCUIT (Click here)  

6.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)
  1. Check the tightening and installation condition of the crankshaft position sensor bolt.

  1. Check the connection of the crankshaft position sensor connector.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL SENSOR (Click here)
OK


7.CHECK CRANKSHAFT POSITION SENSOR
  1. Disconnect the crankshaft position sensor connector.

  1. Check for oil on the connector terminals.

    OK:
    No oil on the terminals.



NG
REPLACE CRANKSHAFT POSITION SENSOR (Click here)
OK


8.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
  1. Check the harnesses and connectors, referring to DTC P0335 inspection procedure .

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9.CHECK CRANKSHAFT POSITION SENSOR
  1. Replace the crankshaft position sensor (Click here).

  1. Check the engine start operation.

    OK:
    Malfunction has been repaired successfully.



NG
REPLACE ECM (Click here)
OK

END (CRANKSHAFT POSITION SENSOR IS DEFECTIVE) 

10.READ FREEZE FRAME DATA
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Using the Techstream, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).

    Result 
    Freeze Frame Data Item
    Suspected Area
    Proceed to
    Coolant Temp, Intake Air
    Coolant Temp
    Fuel Pump/Speed Status
    Difference between Coolant Temp and Intake Air is 10°C (18°F) or more*1
    Coolant Temp is 125°C (257°F) or higher, or lower than outside temperature*3 by 15°C (27°F) or more
    -
    Engine coolant temperature sensor
    A
    Other than above
    All 5 sets of freeze frame data are ON
    -
    B
    At least 1 of the 5 sets of freeze frame data is OFF
    Fuel pump control system
    C
    Difference between Coolant Temp and Intake Air is less than 10°C (18°F)*2
    -
    At least 1 of the 5 sets of freeze frame data is OFF
    Fuel pump control system
    C
    All 5 sets of freeze frame data are ON
    -
    B

    HINT:
    1. *1: A long time had not elapsed after stopping the engine.
    2. *2: A long time had elapsed after stopping the engine.
    3. *3: Use an actual outside temperature estimated from the Initial Intake Air, Ambient Temp for A/C, and (if possible) the weather when the DTC was detected.



B
Go to step 11

C
CHECK FUEL PUMP CONTROL CIRCUIT (Click here)
A

REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)  

11.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE FUEL PUMP/SPEED)
  1. Connect the Techstream to the DLC3.

  1. Disconnect the connector from the fuel suction tube.

  1. Turn the ignition switch to ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.



    A208673E08
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    F19-4 - Body ground
    Active Test is being performed
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Fuel Pump)

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
CHECK FUEL PUMP CONTROL CIRCUIT (Click here)
OK


12.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR ASSEMBLY)
  1. Check the harnesses and connectors, referring to Fuel Injector Circuit inspection procedure .

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
CHECK FUEL INJECTOR CIRCUIT (Click here)
OK


13.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE FUEL PUMP/SPEED)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.

  1. When performing the Active Test, check for fuel leaks from the fuel pipes.
    Result 
    Result
    Proceed to
    Fuel leakage or signs of fuel leaks are present
    A
    No fuel leakage or signs of fuel leaks
    B

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. When performing the Active Test, if there is no operating noise from the fuel pump, the fuel pump system may be malfunctioning.
    3. Check if the vehicle ran out of fuel, as engine starting trouble due to running out of fuel is also detected.



B
Go to step 14
A

REPAIR OR REPLACE FUEL LINE 

14.CHECK FUEL SYSTEM
  1. Check for foreign matter such as iron particles around the fuel pump (fuel pump, fuel pump filter and inside the fuel tank), and for signs that the fuel pump was stuck.
    Result 
    Result
    Proceed to
    There is foreign matter or signs that fuel pump was stuck
    A
    There is no foreign matter and no signs that fuel pump was stuck
    B

    HINT:
    If there is foreign matter such as iron particles on the fuel pump, fuel filter or fuel tank, remove the foreign matter.



B
Go to step 24
A

REPAIR OR REPLACE FUEL SYSTEM 

15.READ FREEZE FRAME DATA
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Using the Techstream, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).

    Result 
    Freeze Frame Data Item
    Suspected Area
    Proceed to
    Coolant Temp, Intake Air
    Coolant Temp
    Long FT #1, Long FT #2
    Engine Speed
    Difference between Coolant Temp and Intake Air is 10°C (18°F) or more
    Coolant Temp is 125°C (257°F) or higher, or lower than outside temperature*2 by 15°C (27°F) or more
    -
    -
    Engine coolant temperature sensor
    A
    Other than above
    -15% or less, or +15% or more
    -
    1. Fuel pump control circuit
    2. Fuel injector assembly
    B
    -15 to +15%
    Minimum speed is 300 rpm or more*1
    Engine assembly
    C
    Minimum speed is less than 300 rpm
    1. Fuel system
    2. Intake air system
    D
    Difference between Coolant Temp and Intake Air is less than 10°C (18°F)
    -
    -15% or less, or +15% or more
    -
    1. Fuel pump control circuit
    2. Fuel injector assembly
    B
    -15 to +15%
    Minimum speed is 300 rpm or more*1
    Engine assembly
    C
    Minimum speed is less than 300 rpm
    1. Fuel system
    2. Intake air system
    D

    HINT:
    1. *1: Compression loss may have occurred in the engine assembly.
    2. *2: Use an actual outside temperature estimated from the Initial Intake Air, Ambient Temp for A/C, and (if possible) the weather when the DTC was detected.



B
Go to step 16

C
CHECK AND REPAIR ENGINE ASSEMBLY

D
Go to step 18
A

REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)  

16.CHECK FUEL INJECTOR ASSEMBLY
  1. Check that no carbon is stuck to the fuel injector.

    OK:
    No carbon present.



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK


17.CHECK FUEL SYSTEM
  1. Check for foreign matter such as iron particles around the fuel pump (fuel pump, fuel pump filter and inside the fuel tank), and for signs that the fuel pump was stuck.
    Result 
    Result
    Proceed to
    There is foreign matter or signs that fuel pump was stuck
    A
    There is no foreign matter and no signs that fuel pump was stuck
    B

    HINT:
    If there is foreign matter such as iron particles on the fuel pump, fuel filter or fuel tank, remove the foreign matter.



B
Go to step 24
A

REPAIR OR REPLACE FUEL SYSTEM 

18.READ FREEZE FRAME DATA
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Using the Techstream, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).

    Result 
    Freeze Frame Data Item
    Result
    Suspected Area
    Proceed to
    Coolant Temp
    Engine coolant temperature is 40°C (104°F) or less*1
    Fuel pressure regulator assembly
    A
    Engine coolant temperature is 40 to 90°C (104 to 194°F)*2
    Fuel injector assembly
    B
    Engine coolant temperature is 90°C (194°F) or higher*3
    Fuel pressure regulator assembly
    A

    HINT:
    *1: If the engine coolant temperature is 40°C (104°F) or less (after stopping the engine and the vehicle has not been driven for a long period of time), the fuel pressure regulator assembly may be stuck open. Attach a fuel pressure gauge and check the ability of the system to maintain fuel pressure after stopping the engine.
    *2: If the engine coolant temperature is 40 to 90°C (104 to 194°F) (15 to 120 minutes have passed after stopping the engine), there may be fuel leaking from a fuel injector assembly.
    *3: If the engine coolant temperature is 90°C (194°F) or more (2 to 5 minutes have passed after stopping the engine), there may be a problem with the fuel pressure regulator assembly failing to maintain the fuel pressure. Attach a fuel pressure gauge and check the ability of the pressure regulator to maintain fuel pressure after stopping the engine.



B
Go to step 20
A


19.CHECK FUEL PRESSURE

HINT:
For the fuel pressure inspection, refer to the following procedures .

  1. Attach a fuel pressure gauge and check the fuel pressure after stopping the engine.

    Standard:
    147 kPa (1.5 kgf/cm2) or higher (5 minutes after stopping the engine)

    HINT:
    If the engine cannot be started, read the values after cranking the engine.

    Result 
    Result
    Proceed to
    Abnormal
    A
    Normal
    B



B
Go to step 24
A

REPLACE FUEL PRESSURE REGULATOR ASSEMBLY (Click here)  

20.INSPECT FUEL INJECTOR ASSEMBLY
  1. Clean the inside of the surge tank with compressed air.

  1. After stopping the engine, measure the HC concentration inside the surge tank for 15 minutes.
    Result 
    Result
    Proceed to
    400 ppm or more
    A
    Less than 400 ppm
    B

    HINT:
    If the concentration is 400 ppm or more, a fuel injector assembly may have a sealing problem.



B
Go to step 22
A


21.INSPECT FUEL INJECTOR ASSEMBLY
  1. Inspect the fuel injector assembly (Click here).
    Result 
    Result
    Proceed to
    Abnormal
    A
    Normal
    B



B
Go to step 22
A

REPLACE FUEL INJECTOR ASSEMBLY (Click here)  

22.CHECK THROTTLE WITH MOTOR BODY ASSEMBLY
  1. Check if carbon is in the airflow passage.
    Result 
    Result
    Proceed to
    Carbon in passage
    A
    No carbon present
    B



B
Go to step 23
A

CLEAN OR REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY (Click here)  

23.CHECK INTAKE SYSTEM
  1. Check the intake system for vacuum leaks.

    OK:
    No leaks in intake system.



NG
REPAIR OR REPLACE INTAKE SYSTEM
OK


24.PERFORM SIMULATION TEST
  1. Check if the engine can be started.
    Result 
    Result
    Proceed to
    Engine can be started
    A
    Engine cannot be started
    B



B
Go to step 25
A

END 

25.CONFIRM PROBLEM SYMPTOM
  1. Confirm the problem symptoms.

    HINT:
    The problem symptoms below can be determined by reading the freeze frame data.


    Result 
    Problem Symptom
    Suspected Area
    Proceed to
    The engine does not crank
    1. Battery fully depleted
    2. Starter (includes pinion gear wear or tooth damage)
    3. Starter system
    4. Engine assembly (excess friction)
    5. Drive plate and ring gear sub-assembly wear or tooth damage*1
    6. Flywheel sub-assembly wear or tooth damage*2
    A
    Abnormal cranking speed
    1. Battery fully depleted
    2. Starter
    3. Engine assembly (excess friction, compression loss)
    B
    There is no initial combustion (combustion does not occur even once)*3
    1. Pressure regulator fuel pressure maintenance
    2. Fuel injector assembly leak
    3. Fuel leak from fuel line
    4. Fuel pump control system
    5. Fuel pump
    6. Spark plug
    7. Crankshaft position sensor system
    8. Ignition coil system
    C
    The engine stalls after starter turnoff (engine stalls immediately after the first time the engine speed increases)*4
    1. Intake system connections
    2. Throttle with motor body assembly
    3. Camshaft timing oil control valve assembly
    4. Mass air flow meter sub-assembly system
    D
    The initial combustion and starter turnoff occur late*5
    1. Engine coolant temperature sensor
    2. Mass air flow meter sub-assembly
    3. Air fuel ratio sensor
    4. Fuel injector assembly
    5. Spark plug
    6. Fuel pressure regulator assembly
    7. Fuel pump
    8. Fuel pump control system
    E
    1. *1: for Automatic Transmission
    2. *2: for Manual Transmission

    HINT:
    1. If there is hesitation (cranking speed is slow and combustion occurs before passing TDC) during the initial cranking period, the battery charge may be insufficient or the starter may be malfunctioning.
    2. *3: If there is no initial combustion, a wire harness may be malfunctioning, or the ignition or fuel system may be malfunctioning.
    3. *4: If the engine stalls after starter turnoff, the air-fuel ratio may be incorrect or the camshaft timing oil control valve assembly may have a problem returning.
    4. *5: If the initial combustion and starter turnoff occur late, the fuel injection volume may be incorrect (too low or too high).



B
Go to step 32

C
Go to step 35

D
Go to step 50

E
Go to step 56
A


26.PERFORM SIMULATION TEST
  1. When cranking the engine, check for a noise indicating that the starter pinion gear is extending, and check that the starter pinion gear is not spinning freely.

    Result 
    Problem Symptom
    Suspected Area
    Proceed to
    A noise indicating that the starter pinion gear is extending is heard and the starter pinion gear is not spinning freely*3
    1. Battery
    2. Excess engine friction
    3. Starter assembly
    A
    A noise indicating that the starter pinion gear is extending is heard but the starter pinion gear is spinning freely
    1. Drive plate and ring gear sub-assembly*1
    2. Flywheel sub-assembly*2
    3. Starter assembly
    B
    A noise indicating that the starter pinion gear is extending is not heard
    1. Battery
    2. Starter assembly
    3. Starter system
    C

    1. *1: for Automatic Transmission
    2. *2: for Manual Transmission

    HINT:
    *3: The battery may be fully depleted or there may be excess engine friction.



B
Go to step 29

C
Go to step 30
A


27.INSPECT BATTERY
  1. Inspect the battery .



NG
CHARGE OR REPLACE BATTERY
OK


28.CHECK ENGINE ASSEMBLY
  1. Check that the crankshaft rotates smoothly when rotating it by hand.

    OK:
    Crankshaft rotates smoothly.

    HINT:
    Excess engine friction may have occurred temporarily. Remove the cylinder head cover and oil pan, and check for foreign matter such as iron fragments. If there is a malfunction or signs of a malfunction present, perform a detailed inspection by disassembling all the parts.

    Result 
    Result
    Proceed to
    NG
    A
    OK
    (for 2WD and Pre-Runner)
    B
    OK
    (for 4WD)
    C



B
REPLACE STARTER ASSEMBLY (for 2WD and Pre-Runner) (Click here)

C
REPLACE STARTER ASSEMBLY (for 4WD) (Click here)
A

REPAIR OR REPLACE ENGINE ASSEMBLY 

29.INSPECT STARTER ASSEMBLY (STARTER PINION GEAR)
  1. Remove the starter assembly.

    HINT:
    1. for 2WD and Pre-Runner: (Click here)
    2. for 4WD: (Click here)

  1. Check for starter pinion gear wear and damage.

    OK:
    There is no wear or damage.

    Result 
    Result
    Proceed to
    NG
    A
    OK
    (for 2WD and Pre-Runner)
    B
    OK
    (for 4WD)
    C



B
REPLACE STARTER ASSEMBLY (for 2WD and Pre-Runner) (Click here)

C
REPLACE STARTER ASSEMBLY (for 4WD) (Click here)
A

REPLACE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY OR FLYWHEEL SUB-ASSEMBLY (Click here)  

30.INSPECT BATTERY
  1. Inspect the battery (Click here).



NG
CHARGE OR REPLACE BATTERY
OK


31.INSPECT STARTER
  1. Inspect the starter.

    HINT:
    1. for 2WD and Pre-Runner: (Click here)
    2. for 4WD: (Click here)

    Result 
    Result
    Proceed to
    NG
    A
    OK
    (for 2WD and Pre-Runner)
    B
    OK
    (for 4WD)
    C



B
REPLACE STARTER ASSEMBLY (for 2WD and Pre-Runner) (Click here)

C
REPLACE STARTER ASSEMBLY (for 4WD) (Click here)
A

CHECK STARTER SIGNAL CIRCUIT (Click here)  

32.PERFORM SIMULATION TEST
  1. Check the cranking speed.

    Result 
    Problem Symptom
    Suspected Area
    Proceed to
    Cranking speed is slow (100 rpm or less)
    1. Battery
    2. Starter assembly
    3. Excess engine friction
    A
    Cranking speed is fast (300 rpm or more)*1
    Engine compression loss
    B

    HINT:
    *1: If the cranking speed is fast, there may be compression loss.



B
CHECK AND REPAIR ENGINE ASSEMBLY
A


33.INSPECT BATTERY
  1. Inspect the battery .



NG
CHARGE OR REPLACE BATTERY
OK


34.CHECK ENGINE ASSEMBLY
  1. Check that the crankshaft rotates smoothly when rotating it by hand.

    OK:
    Crankshaft rotates smoothly.

    Result 
    Result
    Proceed to
    NG
    A
    OK
    (for 2WD and Pre-Runner)
    B
    OK
    (for 4WD)
    C

    HINT:
    Excess engine friction may have occurred temporarily. Remove the cylinder head cover and oil pan, and check for foreign matter such as iron fragments. If there is a malfunction or signs of a malfunction present, perform a detailed inspection by disassembling all the parts.



B
REPLACE STARTER ASSEMBLY (for 2WD and Pre-Runner) (Click here)

C
REPLACE STARTER ASSEMBLY (for 4WD) (Click here)
A

REPAIR OR REPLACE ENGINE ASSEMBLY 

35.INSPECT FUEL INJECTOR ASSEMBLY
  1. Using a sound scope or screwdriver, check for an injector operating noise while cranking the engine.

    OK:
    Fuel injector assembly operating noise is heard.



NG
Go to step 47
OK


36.CHECK FUEL PRESSURE
  1. Inspect the fuel pressure .



NG
Go to step 45
OK


37.CHECK SPARK PLUG AND SPARK
  1. Check for sparks .



NG
Go to step 41
OK


38.CONFIRM VEHICLE CONDITION
  1. Confirm the conditions present when the malfunction occurred based on the customer problem analysis.

    Result 
    Problem Symptom
    Suspected Area
    Proceed to
    When the engine is stopped and a long time has passed, engine starting trouble occurs*1
    Fuel pressure regulator assembly is stuck open
    A
    When the engine is stopped and approximately 15 to 120 minutes have passed, engine starting trouble occurs*2
    Fuel injector assembly leak
    B
    When the engine is stopped and approximately 2 to 3 minutes have passed, engine starting trouble occurs*3
    Failure to maintain fuel pressure by fuel pressure regulator assembly
    A
    Condition other than above, or there is an inconsistency in the conditions present when engine starting trouble occurs
    -
    C*4

    HINT:
    *1: The fuel pressure regulator assembly may be stuck open. Attach a fuel pressure gauge and check the ability of the system to maintain fuel pressure after stopping the engine.
    *2: Fuel may be leaking from a fuel injector assembly.
    *3: The fuel pressure regulator assembly may not be able to maintain the fuel pressure. Attach a fuel pressure gauge and check the ability of the fuel pressure regulator assembly to maintain fuel pressure after stopping the engine.
    *4: From step 70, perform fuel system troubleshooting C (steps 71 to 75).



B
Go to step 40

C
Go to step 70
A


39.CHECK FUEL PRESSURE

HINT:
For the fuel pressure inspection, refer to the following procedures .

  1. Attach a fuel pressure gauge and check the fuel pressure after stopping the engine.

    Standard:
    147 kPa (1.5 kgf/cm2) or higher (5 minutes after stopping the engine)

    Result 
    Result
    Proceed to
    Abnormal
    A
    Normal
    B*1

    HINT:
    1. If the engine cannot be started, check the fuel pressure after cranking the engine.
    2. *1: From step 70, perform fuel system troubleshooting C (steps 71 to 75).



B
Go to step 70
A

REPLACE FUEL PRESSURE REGULATOR ASSEMBLY (Click here)  

40.INSPECT FUEL INJECTOR ASSEMBLY
  1. Clean the inside of the surge tank with compressed air.

  1. After stopping the engine, measure the HC concentration inside the surge tank for 15 minutes.
    Result 
    Result
    Proceed to
    400 ppm or more
    A
    Less than 400 ppm
    B*1

    HINT:
    1. If the concentration is 400 ppm or more, a fuel injector may have a sealing problem.
    2. *1: From step 70, perform fuel system troubleshooting C (steps 71 to 75).



B
Go to step 70
A

REPLACE FUEL INJECTOR ASSEMBLY (Click here)  

41.INSPECT SPARK PLUG
  1. Inspect the spark plugs .

    HINT:
    Even if the spark plug of only one cylinder is malfunctioning, replace the spark plugs of all cylinders.



NG
REPLACE SPARK PLUG (Click here)
OK


42.READ VALUE USING TECHSTREAM (ENGINE SPEED)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.

  1. Start the engine.

  1. While running the engine, read the value of Engine Speed.

    OK:
    A value that matches the actual engine speed is constantly output.

    HINT:
    1. Check the engine speed using a line graph.
    2. If the engine cannot be started, check the engine speed while cranking the engine.
    3. If the engine speed is 0 rpm, the crankshaft position sensor may have an open or short circuit.



NG
CHECK CRANKSHAFT POSITION SENSOR CIRCUIT
OK


43.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IGNITION COIL ASSEMBLY)
  1. Check the harnesses and connectors, referring to DTC P0351 inspection procedure .

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
CHECK POWER SOURCE CIRCUIT (IGNITION COIL ASSEMBLY POWER SOURCE)
OK


44.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)
  1. Check harnesses and connectors, referring to DTC P0351 inspection procedure .

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.
    3. If the wire harness is normal, after replacing the ignition coil assembly, check if engine starting trouble occurs again. If engine starting trouble occurs again, proceed to step 70 and perform troubleshooting for the ignition system (steps 76 to 81).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE IGNITION COIL ASSEMBLY (Click here)  

45.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE FUEL PUMP/SPEED)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.

  1. When performing the Active Test, check for an operating sound from the fuel pump.

    OK:
    Control the Fuel Pump/Speed
    Specified Condition
    ON
    Operating sound heard
    OFF
    Operating sound not heard

    HINT:
    Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.



NG
CHECK FUEL PUMP CONTROL CIRCUIT (Click here)
OK


46.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE FUEL PUMP/SPEED)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.

  1. When performing the Active Test, check for fuel leaks from the fuel pipes.
    Result 
    Result
    Proceed to
    Fuel leaks or signs of fuel leaks are present
    A
    No fuel leaks or signs of fuel leaks
    B

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Check if the vehicle ran out of fuel, as engine starting trouble due to running out of fuel is also detected.
    3. If there are no fuel leaks, after inspecting the Fuel pump control circuit, check if engine starting trouble occurs again. If engine starting trouble occurs again, proceed to step 70 and perform fuel system troubleshooting (steps 71 to 75).



B
CHECK FUEL PUMP CONTROL CIRCUIT (Click here)
A

REPAIR OR REPLACE FUEL LINE 

47.READ VALUE USING TECHSTREAM (ENGINE SPEED)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.

  1. Start the engine.

  1. While running the engine, read the value of Engine Speed.

    OK:
    A value that matches the actual engine speed is constantly output.

    HINT:
    1. Check the engine speed using a line graph.
    2. If the engine cannot be started, check the engine speed while cranking the engine.
    3. If the engine speed is 0 rpm, the crankshaft position sensor may have an open or short circuit.



NG
REPLACE CRANKSHAFT POSITION SENSOR (Click here)
OK


48.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR ASSEMBLY)
  1. Check the harnesses and connectors, referring to Fuel Injector Circuit inspection procedure .

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
CHECK FUEL INJECTOR POWER SOURCE CIRCUIT (Click here)
OK


49.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM)
  1. Check the harnesses and connectors, referring to Fuel Injector Circuit inspection procedure .

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)  

50.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY
  1. Inspect the mass air flow meter sub-assembly .



NG
Go to step 55
OK


51.CHECK INTAKE SYSTEM
  1. Check for air leaks in the intake system [vacuum hose disconnection, cracks, damaged gaskets, etc.].

    HINT:
    1. If the accelerator pedal is released after racing the engine, the inspection is easier to perform because the vacuum inside the intake manifold increases and the air suction noise becomes louder.
    2. If Short FT #1, Short FT #2, Long FT #1 and Long FT #2 are largely different from the normal values (differ by more than 15%) when idling (intake air volume is small) and almost the same as the normal values when racing the engine (for example, when maintaining a speed of 3000 rpm) (intake air volume is high), air leaks may be present.

    OK:
    There are no air leaks.



NG
REPAIR OR REPLACE INTAKE SYSTEM
OK


52.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY
  1. Disconnect the throttle with motor body assembly connector.

    HINT:
    When the connector is disconnected, the vehicle enters fail-safe mode and the throttle valve opening angle is 4 to 7°.

  1. Crank the engine and check that it starts.
    Result 
    Result
    Proceed to
    Engine starts
    A
    Engine does not start
    B

    HINT:
    When this inspection is performed, the MIL may illuminate. After finishing the inspection, check and clear DTCs (Click here).



B
Go to step 54
A


53.CHECK THROTTLE WITH MOTOR BODY ASSEMBLY
  1. Check if carbon is in the air flow passage.

    OK:
    No carbon present.



NG
REMOVE FOREIGN OBJECT AND CLEAN THROTTLE WITH MOTOR BODY ASSEMBLY
OK


54.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE VVT LINEAR)
  1. Performing the Active Test, referring to DTC P0011 inspection procedure .
    Result 
    Result
    Proceed to
    NG
    A
    OK
    B*1

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. When the results of the inspection using the Active Test are normal but the valve operating noise is abnormal, check the valve for any signs of problems.

    *1: From step 70, perform intake system troubleshooting (steps 82 to 84). If engine starting trouble still occurs, perform fuel system troubleshooting A (steps 85 to 92).



B
Go to step 70
A

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (Click here)  

55.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
  1. Check the harnesses and connectors, referring to DTC P0102 inspection procedure .

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.
    3. If the wire harness is normal, after replacing the mass air flow meter sub-assembly, check if engine starting trouble occurs again. If engine starting trouble occurs again, proceed to step 70 and perform intake system troubleshooting (steps 82 to 84). If engine starting trouble still occurs, perform fuel system troubleshooting A (steps 85 to 92).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY (Click here)  

56.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
  1. Inspect the engine coolant temperature sensor (Click here).

    HINT:
    If the engine coolant temperature sensor is malfunctioning, after replacing it, check if engine starting trouble occurs again. If engine starting trouble occurs, replace the ECM. If engine starting trouble still occurs, proceed to step 70 and perform fuel system troubleshooting A (steps 95 to 100), fuel system troubleshooting B (steps 101 to 103), intake system troubleshooting (steps 104 to 106), and ignition system troubleshooting (steps 107 to 112), in that order.



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


57.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
  1. Disconnect the engine coolant temperature sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance 
    Tester Connection
    Condition
    Specified Condition
    E2-2 - E11-17 (THW)
    Always
    Below 1 ฮฉ
    E2-1 - E10-8 (ETHW)
    Always
    Below 1 ฮฉ
    E2-2 or E11-17 (THW) - Body ground
    Always
    10 kฮฉ or higher
    E2-2 or E10-8 (ETHW) - Body ground
    Always
    10 kฮฉ or higher

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.
    3. If the wire harness or connector is malfunctioning, after replacing or repairing it, check if engine starting trouble occurs again. If engine starting trouble occurs, replace the ECM. If engine starting trouble still occurs, proceed to step 70 and perform fuel system troubleshooting A (steps 93 to 100), fuel system troubleshooting B (steps 101 to 103), intake system troubleshooting (steps 104 to 106), and ignition system troubleshooting (steps 107 to 112), in that order.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


58.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY
  1. Inspect the mass air flow meter sub-assembly .

    HINT:
    If the mass air flow meter sub- assembly is malfunctioning, after replacing it, check if engine starting trouble occurs again. If engine starting trouble occurs, replace the ECM. If engine starting trouble still occurs, proceed to step 70 and perform fuel system troubleshooting A (steps 93 to 100), fuel system troubleshooting B (steps 101 to 103), intake system troubleshooting (steps 104 to 106), and ignition system troubleshooting (steps 107 to 112), in that order.



NG
REPLACE MASS AIR FLOW METER SUB-ASSEMBLY (Click here)
OK


59.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
  1. Check the harnesses and connectors, referring to DTC P0102 inspection procedure .

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.
    3. If the wire harness or connector is malfunctioning, after replacing or repairing it, check if engine starting trouble occurs again. If engine starting trouble occurs, replace the ECM. If engine starting trouble still occurs, proceed to step 70 and perform fuel system troubleshooting A (steps 93 to 100), fuel system troubleshooting B (steps 101 to 103), intake system troubleshooting (steps 104 to 106), and ignition system troubleshooting (steps 107 to 112), in that order.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


60.READ VALUE USING TECHSTREAM (LONG FT #1, LONG FT #2 AND ATMOSPHERE PRESSURE)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Long FT #1, Long FT #2 and Atmosphere Pressure.

    Result 
    Data List Item
    Result
    Suspected Area
    Proceed to
    Long FT #1, Long FT #2
    +25% or more or less than -25%
    1. Air fuel ratio sensor
    2. Heated oxygen sensor
    3. Mass air flow meter sub-assembly
    4. Fuel injector assembly
    5. ECM
    A
    Atmosphere Pressure
    80 kPa(abs) [600 mmHg(abs)] or less [when altitude is 0 m (0 ft)]
    Both Data List items listed above
    Values are other than above
    -
    B



B
Go to step 64
A


61.PERFORM SIMULATION TEST
  1. Remove the EFI and ETCS fuses from the engine room relay block.

  1. After 60 seconds or more elapse, install the EFI and ETCS fuses.

  1. Check if the engine can be started.
    Result 
    Result
    Proceed to
    Engine can be started
    A
    Engine cannot be started
    B



B
Go to step 64
A


62.INSPECT AIR FUEL RATIO SENSOR
A215382E11
  1. Connect the Techstream to the DLC3.

  1. Start the engine.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel System Status #1 and Fuel System Status #2.

  1. Confirm that Fuel System Status #1 and Fuel System Status #2 are CL.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / AF Lambda B1S1 and AF Lambda B2S1.

  1. Confirm that AF Lambda B1S1 and AF Lambda B2S1 are within the range of 0.95 to 1.05 when idling.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume.

  1. Read the output voltage from the air fuel ratio sensor when increasing and decreasing the fuel injection volume.

    Standard:
    Techstream Display
    Specified Condition
    Control the Injection Volume
    (12%)
    Air fuel ratio sensor output voltage is below 3.1 V
    Control the Injection Volume
    (-12%)
    Air fuel ratio sensor output voltage is higher than 3.4 V

    HINT:
    1. The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.
    2. If the air fuel ratio sensor is malfunctioning, after replacing it, check if engine starting trouble occurs again. If engine starting trouble occurs, replace the ECM. If engine starting trouble still occurs, proceed to step 70 and perform fuel system troubleshooting A (steps 93 to 100), fuel system troubleshooting B (steps 101 to 103), intake system troubleshooting (steps 104 to 106), and ignition system troubleshooting (steps 107 to 112), in that order.



NG
REPLACE AIR FUEL RATIO SENSOR (Click here)
OK


63.PERFORM SIMULATION TEST
  1. Check if the idling speed is stable after starting the engine.

    OK:
    Speed is stable.

    HINT:
    After replacing the fuel injector or mass air flow meter, check if engine starting trouble occurs again. If engine starting trouble occurs, replace the ECM. If engine starting trouble still occurs, proceed to step 70 and perform fuel system troubleshooting A (steps 93 to 100), fuel system troubleshooting B (steps 101 to 103), intake system troubleshooting (steps 104 to 106), and ignition system troubleshooting (steps 107 to 112), in that order.



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY (Click here)  

64.CHECK FUEL PRESSURE
  1. Check the fuel pressure .



NG
Go to step 69
OK


65.INSPECT SPARK PLUG
  1. Inspect the spark plugs .
    Result 
    Result
    Proceed to
    All cylinders are normal
    A
    One cylinder is abnormal*1
    B
    All cylinders are abnormal*2, *3
    C

HINT:
  1. *1: If one cylinder is abnormal, replace the spark plug of that cylinder and inspect the ignition and fuel system for that cylinder. After performing repairs, check if engine starting trouble occurs again. If engine starting trouble still occurs, proceed to step 70 and perform fuel system troubleshooting A (steps 93 to 100), fuel system troubleshooting B (steps 101 to 103), intake system troubleshooting (steps 104 to 106), and ignition system troubleshooting (steps 107 to 112), in that order.
  2. *2: If all cylinders are abnormal, replace the spark plugs of all cylinders and check if engine starting trouble occurs again. If engine starting trouble still occurs, proceed to step 70 and perform fuel system troubleshooting A (steps 93 to 100), fuel system troubleshooting B (steps 101 to 103), intake system troubleshooting (steps 104 to 106), and ignition system troubleshooting (steps 107 to 112), in that order.
  3. *3: Engine starting trouble may occur if the vehicle is driven extremely short distances repeatedly.



B
REPLACE SPARK PLUG (ABNORMAL CYLINDER) (Click here)

C
REPLACE SPARK PLUG (ALL CYLINDER) (Click here)
A


66.CONFIRM VEHICLE CONDITION
  1. Confirm the conditions present when the malfunction occurred based on the customer problem analysis.

    Result 
    Problem Symptom
    Suspected Area
    Proceed to
    When the engine is stopped and a long time has passed, engine starting trouble occurs*1
    Fuel pressure regulator assembly is stuck open
    A
    When the engine is stopped and approximately 15 to 120 minutes have passed, engine starting trouble occurs*2
    Fuel injector leak
    B
    When the engine is stopped and approximately 2 to 3 minutes have passed, engine starting trouble occurs*3
    Failure to maintain fuel pressure by fuel pressure regulator assembly
    A
    Condition other than above, or there is an inconsistency in the conditions present when engine starting trouble occurs
    -
    C*4

    HINT:
    *1: The fuel pressure regulator assembly may be stuck open. Attach a fuel pressure gauge and check the ability of the system to maintain fuel pressure after stopping the engine.
    *2: Fuel may be leaking from a fuel injector assembly.
    *3: The fuel pressure regulator assembly may not be able to maintain the fuel pressure. Attach a fuel pressure gauge and check the ability of the fuel pressure regulator assembly to maintain fuel pressure after stopping the engine.
    *4: From step 70, perform fuel system troubleshooting A (steps 93 to 100), fuel system troubleshooting B (steps 101 to 103), intake system troubleshooting (steps 104 to 106), and ignition system troubleshooting (steps 107 to 112), in that order.



B
Go to step 68

C
Go to step 70
A


67.CHECK FUEL PRESSURE

HINT:
For the fuel pressure inspection, refer to the following procedures .

  1. Attach a fuel pressure gauge and check the fuel pressure after stopping the engine.

    Standard:
    147 kPa (1.5 kgf/cm2) or higher (5 minutes after stopping the engine)

    Result 
    Result
    Proceed to
    Abnormal
    A
    Normal
    B*1

    HINT:
    1. If the engine cannot be started, check the fuel pressure after cranking the engine.
    2. *1: From step 70, perform fuel system troubleshooting A (steps 93 to 100), fuel system troubleshooting B (steps 101 to 103), intake system troubleshooting (steps 104 to 106), and ignition system troubleshooting (steps 107 to 112), in that order.



B
Go to step 70
A

REPLACE FUEL PRESSURE REGULATOR ASSEMBLY (Click here)  

68.INSPECT FUEL INJECTOR ASSEMBLY
  1. Clean the inside of the surge tank with compressed air.

  1. After stopping the engine, measure the HC concentration inside the surge tank for 15 minutes.
    Result 
    Result
    Proceed to
    400 ppm or more
    A
    Less than 400 ppm
    B*1

    HINT:
    1. If the concentration is 400 ppm or more, a fuel injector assembly may have a sealing problem.
    2. *1: From step 70, perform fuel system troubleshooting A (steps 93 to 100), fuel system troubleshooting B (steps 101 to 103), intake system troubleshooting (steps 104 to 106), and ignition system troubleshooting (steps 107 to 112), in that order.



B
Go to step 70
A

REPLACE FUEL INJECTOR ASSEMBLY (Click here)  

69.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE FUEL PUMP/SPEED)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.

  1. When performing the Active Test, check for fuel leaks from the fuel pipes.
    Result 
    Result
    Proceed to
    Fuel leaks or signs of fuel leaks are present
    A
    No fuel leaks or signs of fuel leaks
    B

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Check if the vehicle ran out of fuel, as engine starting trouble due to running out of fuel is also detected.
    3. If there are no fuel leaks, after inspecting the Fuel pump control circuit, check if engine starting trouble occurs again. If engine starting trouble still occurs, proceed to step 70 and perform fuel system troubleshooting A (steps 93 to 100), fuel system troubleshooting B (steps 101 to 103), intake system troubleshooting (steps 104 to 106), and ignition system troubleshooting (steps 107 to 112), in that order.



B
CHECK FUEL PUMP CONTROL CIRCUIT (Click here)
A

REPAIR OR REPLACE FUEL LINE 

70.CHECK MALFUNCTION CONDITION
  1. If the malfunction could not be identified during the inspections in steps 38, 39, 40 and 46, perform fuel system troubleshooting C (steps 71 to 75).

    Result 
    Performed Step
    Troubleshooting by System
    Procedure
    Proceed to
    Steps 38, 39, 40 and 46
    Fuel system troubleshooting C
    71 to 75
    A

  1. If the malfunction could not be identified during the inspection in step 44, perform ignition system troubleshooting (steps 76 to 81).

    Result 
    Performed Step
    Troubleshooting by System
    Procedure
    Proceed to
    Step 44
    Ignition system troubleshooting
    76 to 81
    B

  1. If the malfunction could not be identified during the inspections in steps 54 and 55, perform intake air system troubleshooting (steps 82 to 84). If engine starting trouble still occurs, perform fuel system troubleshooting A (steps 85 to 92).

    Result 
    Performed Step
    Troubleshooting by System
    Procedure
    Proceed to
    Step 54 and 55
    Intake air system troubleshooting
    82 to 84
    C
    Fuel system troubleshooting A
    85 to 92

  1. If the malfunction could not be identified during the inspections in steps 56, 57, 58, 59, 62, 63, 65, 66, 67, 68 and 69, perform fuel system troubleshooting A (steps 93 to 100), fuel system troubleshooting B (steps 101 to 103), intake air system troubleshooting (steps 104 to 106), and ignition system troubleshooting (steps 107 to 112), in that order.

    Result 
    Performed Step
    Troubleshooting by System
    Procedure
    Proceed to
    Steps 56, 57, 58, 59, 62, 63, 65, 66, 67, 68 and 69
    Fuel system troubleshooting A
    93 to 100
    D
    Fuel system troubleshooting B
    101 to 103
    Intake air system troubleshooting
    104 to 106
    Ignition system troubleshooting
    107 to 112



B
Go to step 76

C
Go to step 82

D
Go to step 93
A


71.INSPECT FUEL INJECTOR ASSEMBLY
  1. Inspect the fuel injector assembly (Click here).



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK


72.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR ASSEMBLY)
  1. Check the harnesses and connectors, referring to Fuel Injector Circuit inspection procedure .

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
CHECK FUEL INJECTOR CIRCUIT (Click here)
OK


73.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM)
  1. Check the harnesses and connectors, referring to Fuel Injector Circuit inspection procedure .

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


74.CHECK CRANKSHAFT POSITION SENSOR
  1. Replace the crankshaft position sensor (Click here).

  1. Check the engine start operation.

    OK:
    Malfunction has been repaired successfully.



NG
Go to step 75
OK

END (CRANKSHAFT POSITION SENSOR IS DEFECTIVE) 

75.CHECK VVT SENSOR
  1. Replace the VVT sensor (Click here).

  1. Check the engine start operation.

    OK:
    Malfunction has been repaired successfully.



NG
REPLACE ECM (Click here)
OK

END (VVT SENSOR IS DEFECTIVE) 

76.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)
  1. Check the tightening and installation condition of the crankshaft position sensor bolt.

  1. Check the connection of the crankshaft position sensor connector.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL CRANKSHAFT POSITION SENSOR (Click here)
OK


77.CHECK SENSOR INSTALLATION (VVT SENSOR)
  1. Check the tightening and installation condition of the VVT sensor bolt.

  1. Check the connection of the VVT sensor connector.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL VVT SENSOR (Click here)
OK


78.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
  1. Check the harnesses and connectors, referring to DTC P0335 inspection procedure .

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


79.CHECK HARNESS AND CONNECTOR (VVT SENSOR - ECM)
  1. Check the harnesses and connectors, referring to DTC P0340 inspection procedure .

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


Go to step 81

80.CHECK CRANKSHAFT POSITION SENSOR
  1. Replace the crankshaft position sensor (Click here).

  1. Check the engine start operation.

    OK:
    Malfunction has been repaired successfully.



NG
Go to step 81
OK

END (CRANKSHAFT POSITION SENSOR IS DEFECTIVE) 

81.CHECK VVT SENSOR
  1. Replace the VVT sensor (Click here).

  1. Check the engine start operation.

    OK:
    Malfunction has been repaired successfully.



NG
REPLACE ECM (Click here)
OK

END (VVT SENSOR IS DEFECTIVE) 

82.READ VALUE USING TECHSTREAM (ISC LEARNING VALUE)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Start the engine and warm it up until the engine coolant temperature stabilizes with the A/C switch and all the accessory switches off.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / ISC Learning Value.

    Result 
    Data List Item
    Result
    Suspected Area
    Proceed to
    ISC Learning Value
    (engine displacement (liters) x 0.9) or more
    1. Valve timing
    2. Compression
    A
    Less than (engine displacement (liters) x 0.9)
    -
    B



B
Go to step 84
A


83.CHECK CYLINDER COMPRESSION PRESSURE
  1. Check the compression .



NG
CHECK AND REPAIR ENGINE ASSEMBLY
OK

CHECK VALVE TIMING  

84.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
  1. Inspect the engine coolant temperature sensor (Click here).



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


85.CHECK FUEL PRESSURE

HINT:
For the fuel pressure inspection, refer to the following procedures .

  1. Attach a fuel pressure gauge and check the fuel pressure when cranking the engine and after stopping the engine.

    Standard:
    Vehicle State
    Specified Condition
    Cranking engine
    304 to 343 kPa (3.1 to 3.5 kgf/cm2)
    5 minutes after stopping engine
    147 kPa (1.5 kgf/cm2) or higher



NG
Go to step 91
OK


86.READ VALUE USING TECHSTREAM (LONG FT #1 AND LONG FT #2)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Long FT #1 and Long FT #2.

    Result 
    Data List Item
    Result
    Suspected Area
    Proceed to
    Long FT #1, Long FT #2
    -15 to +15%
    1. Wire harness or connector
    2. Fuel
    A
    +15% or more, or less than -15%
    Fuel injector assembly
    B



B
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
A


87.PERFORM SIMULATION TEST
  1. Check if the idling speed is stable after starting the engine and if an unstable idling speed has ever occurred in the past.

    Result 
    Problem Symptom
    Suspected Area
    Proceed to
    Current unstable idling speed or history of unstable idling speed
    Crankshaft position sensor system
    A
    All current and past idling speeds are stable
    Fuel
    B

    HINT:
    Through the customer problem analysis, confirm the fuel being used and the location at which the fuel was added to check if the malfunction is caused by the fuel in the vehicle.



B
REPLACE FUEL
A


88.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)
  1. Check the tightening and installation condition of the crankshaft position sensor bolt.

  1. Check the connection of the crankshaft position sensor connector.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL CRANKSHAFT POSITION SENSOR (Click here)
OK


89.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
  1. Check the harnesses and connectors, referring to DTC P0335 inspection procedure .

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


90.CHECK CRANKSHAFT POSITION SENSOR
  1. Replace the crankshaft position sensor (Click here).

  1. Check the engine start operation.

    OK:
    Malfunction has been repaired successfully.



NG
REPLACE ECM (Click here)
OK

END (CRANKSHAFT POSITION SENSOR IS DEFECTIVE) 

91.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE FUEL PUMP/SPEED)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.

  1. When performing the Active Test, check for fuel leaks from the fuel pipes.
    Result 
    Result
    Proceed to
    Fuel leaks or signs of fuel leaks are present
    A
    No fuel leaks or signs of fuel leaks
    B

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. When performing the Active Test, if there is no operating noise from the fuel pump, the fuel pump system may be malfunctioning.
    3. Check if the vehicle ran out of fuel, as engine starting trouble due to running out of fuel is also detected.



B
Go to step 92
A

REPAIR OR REPLACE FUEL LINE 

92.INSPECT FUEL PUMP
  1. Inspect the fuel pump (Click here).

HINT:
  1. Make sure there is no foreign matter such as iron particles on the fuel pump and no signs that the fuel pump was stuck.
  2. Make sure the internal connector is securely connected.
  3. Make sure the fuel pump filter is not clogged.



NG
REPLACE FUEL PUMP (Click here)
OK

REPLACE FUEL PRESSURE REGULATOR ASSEMBLY (Click here)  

93.CHECK FUEL PRESSURE

HINT:
For the fuel pressure inspection, refer to the following procedures .

  1. Attach a fuel pressure gauge and check the fuel pressure after stopping the engine.

    Standard:
    147 kPa (1.5 kgf/cm2) or higher (5 minutes after stopping the engine)



NG
Go to step 99
OK


94.READ VALUE USING TECHSTREAM (LONG FT #1 AND LONG FT #2)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Long FT #1 and Long FT #2.

    Result 
    Data List Item
    Result
    Suspected Area
    Proceed to
    Long FT #1, Long FT #2
    -15 to +15%
    1. Wire harness or connector
    2. Fuel
    A
    +15% or more, or less than -15%
    Fuel injector assembly
    B



B
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
A


95.PERFORM SIMULATION TEST
  1. Check if the idling speed is stable after starting the engine and if an unstable idling speed has ever occurred in the past.

    Result 
    Problem Symptom
    Suspected Area
    Proceed to
    Current unstable idling speed or history of unstable idling speed
    Crankshaft position sensor system
    A
    All current and past idling speeds are stable
    Fuel
    B

    HINT:
    Through the customer problem analysis, confirm the fuel being used and the location at which the fuel was added to check if the malfunction is caused by the fuel in the vehicle.



B
REPLACE FUEL
A


96.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)
  1. Check the tightening and installation condition of the crankshaft position sensor bolt.

  1. Check the connection of the crankshaft position sensor connector.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL CRANKSHAFT POSITION SENSOR (Click here)
OK


97.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
  1. Check the harnesses and connectors, referring to DTC P0335 inspection procedure .

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


98.CHECK CRANKSHAFT POSITION SENSOR
  1. Replace the crankshaft position sensor (Click here).

  1. Check the engine start operation.

    OK:
    Malfunction has been repaired successfully.



NG
REPLACE ECM (Click here)
OK

END (CRANKSHAFT POSITION SENSOR IS DEFECTIVE) 

99.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE FUEL PUMP/SPEED)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.

  1. When performing the Active Test, check for fuel leaks from the fuel pipes.
    Result 
    Result
    Proceed to
    Fuel leaks or signs of fuel leaks are present
    A
    No fuel leaks or signs of fuel leaks
    B

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. When performing the Active Test, if there is no operating noise from the fuel pump, the fuel pump system may be malfunctioning.
    3. Check if the vehicle ran out of fuel, as engine starting trouble due to running out of fuel is also detected.



B
Go to step 100
A

REPAIR OR REPLACE FUEL LINE 

100.INSPECT FUEL PUMP
  1. Inspect the fuel pump (Click here).

HINT:
  1. Make sure there is no foreign matter such as iron particles on the fuel pump and no signs that the fuel pump was stuck.
  2. Make sure the internal connector is securely connected.
  3. Make sure the fuel pump filter is not clogged.



NG
REPLACE FUEL PUMP (Click here)
OK


101.CHECK PURGE VSV


    A254595E01
  1. Disconnect the purge hose (on the canister side) of the purge VSV.

  1. Start the engine.

  1. Idle the engine.

  1. Disconnect the connector of the purge VSV.

  1. Check if air flows through the purge VSV.

    OK:
    Air does not flow.

    Text in Illustration 
    *1
    Hose (to Canister)
    *2
    Purge VSV

    HINT:
    When this inspection is performed, the MIL may illuminate. After finishing the inspection, check and clear DTCs (Click here).



NG
INSPECT PURGE VSV (Click here)
OK


102.CHECK FUEL INJECTOR ASSEMBLY
  1. Clean the inside of the surge tank with compressed air.

  1. After stopping the engine, measure the HC concentration inside the surge tank for 15 minutes.
    Result 
    Result
    Proceed to
    400 ppm or more
    A
    Less than 400 ppm
    B

    HINT:
    If the concentration is 400 ppm or more, a fuel injector assembly may have a sealing problem.



B
Go to step 103
A

REPLACE FUEL INJECTOR ASSEMBLY (Click here)  

103.CHECK INTAKE VALVE
  1. Check if carbon is on the intake valves.
    Result 
    Result
    Proceed to
    Carbon present
    A
    No carbon present
    B



B
Go to step 104
A

CLEAN INTAKE VALVE 

104.READ VALUE USING TECHSTREAM (ISC LEARNING VALUE)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Start the engine, turn off all accessory switches and warm up the engine until the engine coolant temperature stabilizes.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / ISC Learning Value.

    Result 
    Data List Item
    Result
    Suspected Area
    Proceed to
    ISC Learning Value
    (engine displacement (liters) x 0.9) or more
    1. Valve timing
    2. Compression
    A
    Less than (engine displacement (liters) x 0.9)
    -
    B



B
Go to step 106
A


105.CHECK CYLINDER COMPRESSION PRESSURE
  1. Inspect the compression .



NG
CHECK AND REPAIR ENGINE ASSEMBLY
OK

CHECK VALVE TIMING  

106.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
  1. Inspect the engine coolant temperature sensor (Click here).



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


107.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)
  1. Check the tightening and installation condition of the crankshaft position sensor bolt.

  1. Check the connection of the crankshaft position sensor connector.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL CRANKSHAFT POSITION SENSOR (Click here)
OK


108.CHECK SENSOR INSTALLATION (VVT SENSOR)
  1. Check the tightening and installation condition of the VVT sensor bolt.

  1. Check the connection of the camshaft position sensor connector.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL VVT SENSOR (Click here)
OK


109.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
  1. Check the harnesses and connectors, referring to DTC P0335 inspection procedure .

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


110.CHECK HARNESS AND CONNECTOR (VVT SENSOR - ECM)
  1. Check the harnesses and connectors, referring to DTC P0340 inspection procedure .

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


111.CHECK CRANKSHAFT POSITION SENSOR
  1. Replace the crankshaft position sensor (Click here).

  1. Check the engine start operation.

    OK:
    Malfunction has been repaired successfully.



NG
Go to step 112
OK

END (CRANKSHAFT POSITION SENSOR IS DEFECTIVE) 

112.CHECK VVT SENSOR
  1. Replace the VVT sensor (Click here).

  1. Check the engine start operation.

    OK:
    Malfunction has been repaired successfully.



NG
REPLACE ECM (Click here)
OK

END (VVT SENSOR IS DEFECTIVE)