1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2. DISCHARGE FUEL SYSTEM PRESSURE
3.REMOVE FRONT WHEEL RH
51442C
4.REMOVE ENGINE UNDER COVER LH (w/o Metal Type Under Cover)
51441C
5.REMOVE ENGINE UNDER COVER RH (w/o Metal Type Under Cover)
51451A
6.REMOVE CENTER ENGINE UNDER COVER (w/ Metal Type Under Cover)
51405A
7.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (w/ Metal Type Under Cover)
8.DRAIN ENGINE OIL
9.DRAIN ENGINE COOLANT
10.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
55781E
11.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY
58910C
12.REMOVE REAR CONSOLE BOX ASSEMBLY
57533B
13.REMOVE FRONT FLOOR CENTER BRACE
17410
14.REMOVE FRONT EXHAUST PIPE ASSEMBLY
27060
15.REMOVE GENERATOR WITH REGULATOR ASSEMBLY
23820
16.DISCONNECT FUEL VAPOR FEED HOSE ASSEMBLY
23827A
17.DISCONNECT NO. 2 FUEL VAPOR FEED HOSE
17341T
18.DISCONNECT NO. 1 AIR HOSE (for Automatic Transaxle)
17735
19.REMOVE AIR CLEANER CAP WITH NO. 1 AIR CLEANER HOSE
23820
20.REMOVE FUEL VAPOR FEED HOSE ASSEMBLY
28800
21.REMOVE BATTERY
Separate the terminal cover from the positive (+) battery terminal.
Loosen the nut and disconnect the positive (+) battery terminal from the battery.
Remove the 2 nuts, battery clamp bolt and battery clamp sub-assembly from the battery carrier assembly.
Remove the battery from the battery tray.
74431
22.REMOVE BATTERY TRAY
17361M
23.SEPARATE AIR TUBE (for Automatic Transaxle)
23842A
24.REMOVE EFI FUEL PIPE CLAMP
23901
25.DISCONNECT FUEL TUBE SUB-ASSEMBLY
87245
26.DISCONNECT INLET HEATER WATER HOSE
87246
27.DISCONNECT OUTLET HEATER WATER HOSE
28.DISCONNECT RADIATOR RESERVOIR TANK HOSE
16573B
29.DISCONNECT NO. 3 RADIATOR HOSE
16502
30.REMOVE WATER FILLER SUB-ASSEMBLY
12261
31.REMOVE VENTILATION HOSE
44774
32.DISCONNECT UNION TO CONNECTOR TUBE HOSE
Loosen the hose clip and disconnect the union to connector tube hose from the intake manifold.
15301
33.REMOVE OIL LEVEL DIPSTICK SUB-ASSEMBLY
17111
34.REMOVE INTAKE MANIFOLD WITH THROTTLE BODY WITH MOTOR ASSEMBLY
Disengage the clamp to disconnect the No. 2 water by-pass hose from the hose clamp.
Loosen the hose clip and disconnect the No. 2 water by-pass hose from the throttle body with motor assembly.
Loosen the hose clip and disconnect the water by-pass hose from the throttle body with motor assembly.
Disengage the 2 clamps to disconnect the engine wire from the 2 wire harness clamp brackets.
Disconnect the throttle body with motor assembly connector.
Disengage the 3 clamps to separate the engine wire from the 3 wire harness clamp brackets.
Remove the 3 bolts, 2 nuts and intake manifold with throttle body with motor assembly from the cylinder head sub-assembly.
Remove the intake manifold to head gasket from the intake manifold.
11452
35.REMOVE OIL LEVEL DIPSTICK GUIDE
Disengage the clamp to disconnect the engine wire from the oil level dipstick guide.
Remove the bolt and oil level dipstick guide from the cylinder block sub-assembly.
Remove the O-ring from the oil level dipstick guide.
89615
36.REMOVE KNOCK SENSOR
16268
37.REMOVE NO. 1 WATER BY-PASS PIPE
44772
38.DISCONNECT CHECK VALVE TO CONNECTOR TUBE HOSE
82121
39.DISCONNECT ENGINE WIRE
Remove the 2 bolts to disconnect the engine wire from the cylinder head sub-assembly.
Disconnect the engine wire from the cylinder head sub-assembly.
25591
40.REMOVE MANIFOLD SUPPORT BRACKET
19500D
41.REMOVE NO. 1 IGNITION COIL
11201
42.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY
12305
43.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH
13407
44.REMOVE CRANKSHAFT DAMPER SUB-ASSEMBLY
15100Q
45.REMOVE CRANKSHAFT POSITION SENSOR
11101J
46.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
16173
47.REMOVE WATER PUMP PULLEY
16100
48.REMOVE ENGINE WATER PUMP ASSEMBLY
12315A
49.REMOVE ENGINE MOUNTING BRACKET RH
15100
50.REMOVE OIL PUMP ASSEMBLY
15100C
51.REMOVE OIL PUMP SEAL
13540
52.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY
13559
53.REMOVE CHAIN TENSIONER SLIPPER
13561
54.REMOVE NO. 1 CHAIN VIBRATION DAMPER
13506
55.REMOVE CHAIN SUB-ASSEMBLY
13512
56.REMOVE NO. 2 CAMSHAFT
13511
57.REMOVE CAMSHAFT
11101
58.REMOVE CYLINDER HEAD SUB-ASSEMBLY
Using an 8 mm bi-hexagon wrench, uniformly loosen and remove the 10 cylinder head set bolts and 10 plate washers in several steps and in the sequence shown in the illustration.
Do not drop the plate washers into the cylinder head sub-assembly.
Head warpage or cracking could result from removing the cylinder head set bolts in the wrong sequence.
Remove the cylinder head sub-assembly from the cylinder block sub-assembly.
11115
59.REMOVE CYLINDER HEAD GASKET
Remove the cylinder head gasket from the cylinder block sub-assembly.