Home › Engine / Hybrid System › 1NZ-FE ENGINE MECHANICAL › CYLINDER HEAD GASKET › 2014.03–2016.07
RM30M0E _51 Engine / Hybrid System _017073 1NZ-FE ENGINE MECHANICAL _0091002 CYLINDER HEAD GASKET A

1NZ-FE ENGINE MECHANICAL  CYLINDER HEAD GASKET  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2. DISCHARGE FUEL SYSTEM PRESSURE

Hide 3.REMOVE FRONT WHEEL RH

Hide 51442C 4.REMOVE ENGINE UNDER COVER LH (w/o Metal Type Under Cover)

Hide 51441C 5.REMOVE ENGINE UNDER COVER RH (w/o Metal Type Under Cover)

Hide 51451A 6.REMOVE CENTER ENGINE UNDER COVER (w/ Metal Type Under Cover)

Hide 51405A 7.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (w/ Metal Type Under Cover)

Hide 10.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 55781E 11.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 58910C 12.REMOVE REAR CONSOLE BOX ASSEMBLY (w/ Console Box Lid)

Hide 58910C 13.REMOVE REAR CONSOLE BOX ASSEMBLY (w/o Console Box Lid)

Hide 57533B 14.REMOVE FRONT FLOOR CENTER BRACE

Hide 17410 15.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 27060 16.REMOVE GENERATOR WITH REGULATOR ASSEMBLY

Hide 23820 17.DISCONNECT FUEL VAPOR FEED HOSE ASSEMBLY

Hide 23827A 18.DISCONNECT NO. 2 FUEL VAPOR FEED HOSE

Hide 17341T 19.DISCONNECT NO. 1 AIR HOSE (for Automatic Transaxle)

Hide 17735 20.REMOVE AIR CLEANER CAP WITH NO. 1 AIR CLEANER HOSE

Hide 28800 22.REMOVE BATTERY

a.

Separate the terminal cover from the positive (+) battery terminal.


b.
A107445

Loosen the nut and disconnect the positive (+) battery terminal from the battery.


c.

Remove the 2 nuts, battery clamp bolt and battery clamp sub-assembly from the battery carrier assembly.


d.

Remove the battery from the battery tray.


Hide 17361M 24.SEPARATE AIR TUBE (for Automatic Transaxle)

Hide 23842A 25.REMOVE EFI FUEL PIPE CLAMP

Hide 23901 26.DISCONNECT FUEL TUBE SUB-ASSEMBLY

Hide 29.DISCONNECT RADIATOR RESERVOIR TANK HOSE

Hide 44774 33.DISCONNECT UNION TO CONNECTOR TUBE HOSE

a.
A116744

Loosen the hose clip and disconnect the union to connector tube hose from the intake manifold.


Hide 15301 34.REMOVE OIL LEVEL DIPSTICK SUB-ASSEMBLY

Hide 17111 35.REMOVE INTAKE MANIFOLD WITH THROTTLE BODY WITH MOTOR ASSEMBLY

a.
A300592

Disengage the clamp to disconnect the No. 2 water by-pass hose from the hose clamp.


b.

Loosen the hose clip and disconnect the No. 2 water by-pass hose from the throttle body with motor assembly.


c.
A300593

Loosen the hose clip and disconnect the water by-pass hose from the throttle body with motor assembly.


d.
A107448

Disengage the 2 clamps to disconnect the engine wire from the 2 wire harness clamp brackets.


e.

Disconnect the throttle body with motor assembly connector.


f.
A268159

Disengage the 3 clamps to separate the engine wire from the 3 wire harness clamp brackets.


g.
A116746

Remove the 3 bolts, 2 nuts and intake manifold with throttle body with motor assembly from the cylinder head sub-assembly.


h.

Remove the intake manifold to head gasket from the intake manifold.


Hide 11452 36.REMOVE OIL LEVEL DIPSTICK GUIDE

A268160

a.

Disengage the clamp to disconnect the engine wire from the oil level dipstick guide.


b.

Remove the bolt and oil level dipstick guide from the cylinder block sub-assembly.


c.

Remove the O-ring from the oil level dipstick guide.


Hide 16268 38.REMOVE NO. 1 WATER BY-PASS PIPE

Hide 44772 39.DISCONNECT CHECK VALVE TO CONNECTOR TUBE HOSE

Hide 82121 40.DISCONNECT ENGINE WIRE

A121490

a.

Remove the 2 bolts to disconnect the engine wire from the cylinder head sub-assembly.


b.

Disconnect the engine wire from the cylinder head sub-assembly.


Hide 25591 41.REMOVE MANIFOLD SUPPORT BRACKET

Hide 11201 43.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 12305 44.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

Hide 13407 45.REMOVE CRANKSHAFT DAMPER SUB-ASSEMBLY

Hide 15100Q 46.REMOVE CRANKSHAFT POSITION SENSOR

Hide 11101J 47.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

Hide 16173 48.REMOVE WATER PUMP PULLEY

Hide 16100 49.REMOVE ENGINE WATER PUMP ASSEMBLY

Hide 12315A 50.REMOVE ENGINE MOUNTING BRACKET RH

Hide 15100 51.REMOVE OIL PUMP ASSEMBLY

Hide 15100C 52.REMOVE OIL PUMP SEAL

Hide 13540 53.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

Hide 13559 54.REMOVE CHAIN TENSIONER SLIPPER

Hide 13561 55.REMOVE NO. 1 CHAIN VIBRATION DAMPER

Hide 11101 59.REMOVE CYLINDER HEAD SUB-ASSEMBLY

A133597E01
0.625,0.104 0.781,0.302 0.156,0.198 10 false 3 1.115,1.729 1.271,1.927 0.156,0.198 10 false 5 1.615,1.74 1.854,1.948 0.24,0.208 10 false 10 2.177,1.729 2.417,1.938 0.24,0.208 10 false 8 2.677,1.74 2.917,1.948 0.24,0.208 10 true 4 1.135,0.104 1.292,0.302 0.156,0.198 10 false 7 1.656,0.104 1.813,0.302 0.156,0.198 10 false 9 2.698,0.094 2.854,0.292 0.156,0.198 10 false 2 2.156,0.094 2.313,0.292 0.156,0.198 10 false 6 0.625,1.74 0.781,1.938 0.156,0.198 10 false 1

a.

Using an 8 mm bi-hexagon wrench, uniformly loosen and remove the 10 cylinder head set bolts and 10 plate washers in several steps and in the sequence shown in the illustration.

NOTICE:
·

Do not drop the plate washers into the cylinder head sub-assembly.

·

Head warpage or cracking could result from removing the cylinder head set bolts in the wrong sequence.




b.

Remove the cylinder head sub-assembly from the cylinder block sub-assembly.


Hide 11115 60.REMOVE CYLINDER HEAD GASKET

A310642

a.

Remove the cylinder head gasket from the cylinder block sub-assembly.