The engine assembly with manual transaxle assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop.
1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM (w/ Fan Shroud Ventilation Duct)
3.DISCHARGE FUEL SYSTEM PRESSURE
4.REMOVE FRONT WHEELS
51442C
5.REMOVE ENGINE UNDER COVER LH (w/o Metal Type Under Cover)
Remove the 3 bolts, 5 screws and engine under cover LH from the vehicle.
51441C
6.REMOVE ENGINE UNDER COVER RH (w/o Metal Type Under Cover)
Remove the 2 bolts, 2 screws and engine under cover RH from the vehicle.
51451A
7.REMOVE CENTER ENGINE UNDER COVER (w/ Metal Type Under Cover)
Remove the 4 screws, 5 clips and center engine under cover from the vehicle.
51405A
8.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (w/ Metal Type Under Cover)
Remove the 11 bolts and No. 1 engine under cover sub-assembly from the vehicle.
9.DRAIN ENGINE COOLANT
10.DRAIN MANUAL TRANSAXLE OIL
11.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
11212
12.REMOVE NO. 2 CYLINDER HEAD COVER
23820
13.DISCONNECT FUEL VAPOR FEED HOSE ASSEMBLY
23827A
14.DISCONNECT NO. 2 FUEL VAPOR FEED HOSE
17735
15.REMOVE AIR CLEANER CAP WITH NO. 1 AIR CLEANER HOSE
17801
16.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
Remove the air cleaner filter element sub-assembly from the air cleaner case sub-assembly.
17.REMOVE AIR CLEANER CASE SUB-ASSEMBLY
Disengage the clamp to disconnect the engine wire from the air cleaner case sub-assembly.
Remove the 3 bolts and air cleaner case sub-assembly from the air cleaner bracket.
23820
18.REMOVE FUEL VAPOR FEED HOSE ASSEMBLY
Loosen the 2 hose clips and remove the fuel vapor feed hose assembly from the cylinder head cover sub-assembly and fuel tube.
28800
19.REMOVE BATTERY
Remove the terminal cover from the positive (+) battery terminal.
| *1 | Engine Room Main Wire |
| *2 | Engine Wire |
Remove the nut and disconnect the engine room main wire with engine wire from the positive (+) battery terminal.
Disengage the 2 claws to disconnect the engine room main wire from the engine wire.
Remove the 2 nuts, battery clamp bolt and battery clamp sub-assembly from the battery carrier assembly.
Remove the battery from the battery tray.
74431
20.REMOVE BATTERY TRAY
Remove the battery tray from the battery carrier assembly.
74410
21.REMOVE BATTERY CARRIER ASSEMBLY
Disengage the 6 clamps to disconnect the engine wire from the battery carrier assembly.
Remove the 5 bolts and battery carrier assembly from the engine mounting insulator LH and vehicle.
22.DISCONNECT RADIATOR RESERVOIR TANK HOSE
16573B
23.DISCONNECT NO. 3 RADIATOR HOSE
Loosen the hose clip and disconnect the No. 3 radiator hose from the water filler sub-assembly.
16572D
24.DISCONNECT NO. 2 RADIATOR HOSE
Loosen the hose clip and disconnect the No. 2 radiator hose from the water inlet.
87245
25.DISCONNECT INLET HEATER WATER HOSE
Loosen the hose clip and disconnect the inlet heater water hose from the cylinder head sub-assembly.
87246
26.DISCONNECT OUTLET HEATER WATER HOSE
Loosen the hose clip and disconnect the outlet heater water hose from the No. 1 water by-pass pipe.
23842A
27.REMOVE EFI FUEL PIPE CLAMP
23901
28.DISCONNECT FUEL TUBE SUB-ASSEMBLY
44772
29.DISCONNECT CHECK VALVE TO CONNECTOR TUBE HOSE
Loosen the hose clip and disconnect the check valve to connector tube hose from the booster vacuum tube.
16361A
30.REMOVE FAN AND GENERATOR V BELT
31470
31.SEPARATE CLUTCH RELEASE CYLINDER ASSEMBLY
88320
32.SEPARATE COOLER COMPRESSOR ASSEMBLY (w/o Fan Shroud Ventilation Duct)
Disconnect the cooler compressor assembly connector.
Remove the 3 bolts to separate the cooler compressor assembly from the oil pan sub-assembly.
Separate the cooler compressor assembly together with the No. 1 cooler refrigerant discharge hose and No. 1 cooler refrigerant suction hose, then suspend them from the vehicle with a piece of rope.
88711
33.DISCONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE (w/ Fan Shroud Ventilation Duct)
88712
34.DISCONNECT NO. 1 COOLER REFRIGERANT SUCTION HOSE (w/ Fan Shroud Ventilation Duct)
88320
35.REMOVE COOLER COMPRESSOR ASSEMBLY (w/ Fan Shroud Ventilation Duct)
55550
36.REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY
82121
37.DISCONNECT ENGINE WIRE
Remove the relay block cover from the engine room relay block.
Disengage the clamp to disconnect the engine wire from the vehicle.
Disconnect the connector from the engine room relay block.
Remove the nut from the engine room relay block.
Disengage the 2 claws to disconnect the engine wire from the engine room relay block.
Disconnect the 3 connectors as shown in the illustration.
Disengage the 2 clamps to disconnect the engine wire from the wire harness clamp bracket and vehicle.
Disengage the clamp to disconnect the engine wire from the wire harness clamp bracket.
Disengage the grommet and pass the engine wire through the hole to the inside of the engine room.
Disengage the 2 clamps to disconnect the engine wire from the engine mounting bracket LH.
Remove the bolt to disconnect the engine wire from the manual transaxle assembly.
58910C
38.REMOVE REAR CONSOLE BOX ASSEMBLY (w/ Console Box Lid)
58910C
39.REMOVE REAR CONSOLE BOX ASSEMBLY (w/o Console Box Lid)
57533B
40.REMOVE FRONT FLOOR CENTER BRACE
17410
41.REMOVE FRONT EXHAUST PIPE ASSEMBLY
33820B
42.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
43420
43.REMOVE FRONT DRIVE SHAFT ASSEMBLY
45259A
44.REMOVE COLUMN HOLE COVER SILENCER SHEET
45209
45.SEPARATE STEERING SLIDING YOKE SUB-ASSEMBLY
45025D
46.SEPARATE NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY
47.REMOVE ENGINE ASSEMBLY WITH MANUAL TRANSAXLE ASSEMBLY
Loosen the engine moving control rod bolt.
|
Attachment Placement Position |
Place the height adjustment attachments or plate lift attachments in the positions shown in the illustration and set an engine lifter underneath the engine assembly with manual transaxle assembly and front suspension crossmember sub-assembly.
Place the height adjustment attachments or plate lift attachments so that the engine assembly with manual transaxle assembly is level.
Do not perform any procedure while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.
As the engine assembly with manual transaxle assembly is very heavy, be sure to support it securely.
To prevent deformation of the No. 2 oil pan sub-assembly, never set any attachments against the No. 2 oil pan sub-assembly of the engine assembly.
Remove the bolt and 2 nuts to disconnect the engine mounting insulator sub-assembly RH from the engine mounting bracket RH.
Remove the through bolt and nut to disconnect the engine mounting insulator LH from the engine mounting bracket LH.
Loosen by holding the nut and turning the through bolt.
Remove the 6 bolts, engine assembly with manual transaxle assembly and front suspension crossmember sub-assembly from the vehicle.
When removing the engine assembly with manual transaxle assembly and front suspension crossmember sub-assembly, be careful not to damage any engine wire or the steering shaft.
12281A
48.INSTALL NO. 1 ENGINE HANGER
Separate the air fuel ratio sensor wire from the wire harness clamp bracket.
Remove the bolt and wire harness clamp bracket from the cylinder head sub-assembly.
| *1 | No. 1 Engine Hanger |
| *a | Front Side |
| *b | Rear Side |
Install the 2 No. 1 engine hangers to the cylinder head sub-assembly with the 2 bolts.
| Part Name | Part No. |
|---|---|
| No. 1 Engine Hanger | 12281-0M020 |
| Bolt | 90119-T0011 |
51201
49.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
Using an engine sling device and a chain block, suspend the engine assembly with manual transaxle assembly.
Remove the through bolt and front suspension crossmember sub-assembly from the engine moving control rod bracket.
50.FIX MANUAL TRANSAXLE ASSEMBLY
Attach the sling device to the engine hangers and chain block.
Make sure that the sling angle is correct to prevent the engine assembly and engine hangers from being damaged or deformed.
|
Attachment Placement Position |
To enable removal of the engine assembly, adjust the positions of the height adjustment attachments or plate lift attachments and set them in place.
Place the height adjustment attachments or plate lift attachments so that the engine assembly with manual transaxle assembly is level.
As the engine assembly with manual transaxle assembly is very heavy, be sure to support it securely.
Use a lashing belt or a rope to secure the manual transaxle assembly to the engine lifter.
Do not tighten the lashing belt or the rope any more than is necessary.
12321B
51.REMOVE DRIVE SHAFT HEAT INSULATOR SUB-ASSEMBLY
11363A
52.REMOVE FLYWHEEL HOUSING SIDE COVER
28100
53.REMOVE STARTER ASSEMBLY
33524B
54.REMOVE CONTROL CABLE BRACKET
Remove the 2 bolts and control cable bracket from the manual transaxle assembly.
55.REMOVE ENGINE ASSEMBLY
Remove the 7 bolts and engine assembly from the manual transaxle assembly.
Bolt A: Remove from manual transaxle assembly side
Bolt B: Remove from engine assembly side
31210
56.REMOVE CLUTCH COVER ASSEMBLY
31250B
57.REMOVE CLUTCH DISC ASSEMBLY
13405
58.REMOVE FLYWHEEL SUB-ASSEMBLY
Using height adjustment attachments or plate lift attachments, place the engine assembly on a flat, level surface.
Using height adjustment attachments or plate lift attachments, place the engine assembly horizontally.
To prevent the No. 2 oil pan sub-assembly from deforming, do not place any attachments under the No. 2 oil pan sub-assembly of the engine assembly.
Using an engine sling device and engine lift, secure the engine assembly before servicing.
Using SST, hold the crankshaft damper sub-assembly.
Remove the 6 bolts and flywheel sub-assembly from the crankshaft.
59.INSTALL ENGINE STAND
Using a sling device and a chain block, install the engine stand to the engine assembly.
Make sure that the sling angle is correct to prevent the engine assembly and engine hangers from being damaged or deformed.
Securely support the engine assembly to prevent it from turning upside down until it is secured to an engine stand.
82121
60.REMOVE ENGINE WIRE
Remove the 2 bolts to disconnect the engine wire from the cylinder head sub-assembly.
Disconnect all the engine wire and connectors. Make sure that no engine wire are connected to the engine assembly.
12261
61.REMOVE VENTILATION HOSE
Loosen the 2 hose clips and remove the ventilation hose from the cylinder head cover sub-assembly and intake manifold.
16502
62.REMOVE WATER FILLER SUB-ASSEMBLY
Loosen the hose clip and disconnect the No. 1 radiator hose from the cylinder head sub-assembly.
Remove the 2 nuts and water filler sub-assembly from the throttle body with motor assembly.
15301
63.REMOVE OIL LEVEL DIPSTICK SUB-ASSEMBLY
17111
64.REMOVE INTAKE MANIFOLD WITH THROTTLE BODY WITH MOTOR ASSEMBLY
Loosen the hose clip and disconnect the union to connector tube hose from the booster vacuum tube.
Loosen the hose clip and disconnect the water by-pass hose from the cylinder head sub-assembly.
Loosen the hose clip and disconnect the No. 2 water by-pass hose from the No. 1 water by-pass pipe.
Remove the 3 bolts, 2 nuts and intake manifold with throttle body with motor assembly from the cylinder head sub-assembly.
Remove the intake manifold to head gasket from the intake manifold.
17167
65.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
25591
66.REMOVE MANIFOLD SUPPORT BRACKET
17141
67.REMOVE EXHAUST MANIFOLD
19500D
68.REMOVE NO. 1 IGNITION COIL
12305
69.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH
Only perform this procedure when replacement of the engine mounting insulator sub-assembly RH is necessary.
Remove the 3 bolts and engine mounting insulator sub-assembly RH from the vehicle.
12372A
70.REMOVE ENGINE MOUNTING INSULATOR LH
Only perform this procedure when replacement of the engine mounting insulator LH is necessary.
Remove the 5 bolts and engine mounting insulator LH from the vehicle.