Section 3 - Driveline / Axle
Section 3 - Driveline / Axle
Section 3A - Drive Shaft / Axle
Front
NOTE:
For fastener(s) with * (asterisk) below, refer to the specified procedure in “Repair Instructions”.
| Fastening part | Tightening torque | Note | ||
|---|---|---|---|---|
| N·m | kgf-m | lbf-ft | ||
| Drive shaft nut | 200 | 20.4 | 147.5 |
 |
| Intermediate support bolt* | 55 | 5.6 | 40.5 |
|
Reference:
For the tightening torques of fasteners not specified in this page, refer to:
Rear
| Fastening part | Tightening torque | Note | ||
|---|---|---|---|---|
| N·m | kgf-m | lbf-ft | ||
| Drive shaft flange nut | 50 | 5.1 | 37.0 |
|
| Drive shaft nut | 175 | 17.8 | 129.0 |
|
| Rear wheel hub assembly bolt | 88 | 9.0 | 65.0 |
|
Reference:
For the tightening torques of fasteners not specified in this page, refer to:
Section 3B - Differential
| Fastening part | Tightening torque | Note | ||
|---|---|---|---|---|
| N·m | kgf-m | lbf-ft | ||
| Rear differential oil level / filler plug | 23 | 2.3 | 17.0 |
|
| Rear differential oil drain plug | 23 | 2.3 | 17.0 |
|
| Rear drive shaft flange nut | 50 | 5.1 | 37.0 |
|
| Rear drive coupling air temperature sensor | 18 | 1.8 | 13.5 |
|
| Rear differential mounting arm bolt | 80 | 8.2 | 59.0 |
|
| Rear differential mounting rear bracket bolt | 80 | 8.2 | 59.0 |
|
| Bevel pinion nut | 230 – 340 | 23.5 – 34.7 | 170.0 – 251.0 |
|
| Bevel gear bolt | 78 | 8.0 | 57.5 |
|
| Differential cover bolt | 23 | 2.3 | 17.0 |
|
| Companion flange nut | 110 | 11.2 | 81.5 |
|
| Rear drive coupling case bolt | 23 | 2.3 | 17.0 |
|
| Rear differential front mounting bolt | 50 | 5.1 | 37.0 |
|
| Rear differential front mounting nut | 50 | 5.1 | 37.0 |
|
| Mass damper nut | 23 | 2.3 | 17.0 |
|
| Mass damper bolt | 23 | 2.3 | 17.0 |
|
| Rear differential rear bracket bolt | 80 | 8.2 | 59.0 |
|
Reference:
For the tightening torques of fasteners not specified in this page, refer to:
Section 3C - Transfer
NOTE:
For fastener(s) with * (asterisk) below, refer to the specified procedure in “Repair Instructions”.
| Fastening part | Tightening torque | Note | ||
|---|---|---|---|---|
| N·m | kgf-m | lbf-ft | ||
| Transfer oil level / filler plug | 23 | 2.3 | 17.0 |
|
| Transfer oil drain plug | 23 | 2.3 | 17.0 |
|
| Transfer oil temperature sensor | 12 | 1.2 | 9.0 |
|
| Transfer stiffener bolt* | 55 | 5.6 | 40.5 |
|
| Transfer bolt | 88 | 9.0 | 65.0 |
|
| Transfer nut | 88 | 9.0 | 65.0 |
|
| Transfer output flange nut | 100 – 300 | 10.2 – 30.6 | 74.0 – 221.5 |
|
| Oil pump outer cover bolt | 8.0 | 0.82 | 6.0 |
|
| Transfer case bolt | 23 | 2.3 | 17.0 |
|
| Transfer output retainer bolt | 55 | 5.6 | 40.5 |
|
Reference:
For the tightening torques of fasteners not specified in this page, refer to:
Section 3D - Propeller Shaft
| Fastening part | Tightening torque | Note | ||
|---|---|---|---|---|
| N·m | kgf-m | lbf-ft | ||
| Propeller shaft bolt | 33 | 3.4 | 24.5 |
|
| Center support bolt | 50 | 5.1 | 37.0 |
|
Reference:
For the tightening torques of fasteners not specified in this page, refer to: