Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > Short to B+ in CAN Bus Line

for Preparation Click here


DESCRIPTION

There may be a short circuit between the CAN bus lines and +B when the resistance between terminals 6 (CANH) and 16 (BAT) or terminals 14 (CANL) and 16 (BAT) of the DLC3 is below 6 kΩ.

Symptom
Trouble Area
The resistance between terminals 6 (CANH) and 16 (BAT) or terminals 14 (CANL) and 16 (BAT) of the DLC3 is below 6 kΩ.
  1. Short between CAN bus line and +B
  2. Combination meter assembly
  3. Skid control ECU (master cylinder solenoid)
  4. Main body ECU (multiplex network body ECU)
  5. Airbag sensor assembly
  6. Steering angle sensor (spiral cable sub-assembly)
  7. Navigation receiver assembly*1
  8. Radio and display receiver assembly*2
  9. Certification ECU (smart key ECU assembly)*3
  10. Power steering ECU assembly
  11. Yaw rate sensor assembly
  12. Power management control ECU*3
  13. Four wheel drive control ECU*4
  14. Stabilizer control ECU*5
  15. Air conditioning amplifier assembly*6
  16. ECM
  17. No. 1 junction connector
  18. No. 2 junction connector
  19. No. 3 junction connector
  20. No. 4 junction connector
  1. *1: for Navigation Receiver Type
  2. *2: for Radio and Display Receiver Type
  3. *3: w/ Smart Key System
  4. *4: for 4WD
  5. *5: w/ Kinetic Dynamic Suspension System
  6. *6: w/o Smart Key System

WIRING DIAGRAM


C292507E01


C292508E01


C292509E01


C292510E01


INSPECTION PROCEDURE

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


2.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (DLC3 BRANCH WIRE)


    H102621E60
  1. Disconnect the F59 No. 2 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F13-6 (CANH) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    F13-14 (CANL) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)
OK


3.CONNECT CONNECTOR
  1. Reconnect the F59 No. 2 junction connector connector.


NEXT


4.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR SIDE)


    H102621E60
  1. Disconnect the A36 No. 1 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F13-6 (CANH) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    F13-14 (CANL) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of DLC3



NG
Go to step 11
OK


5.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - SKID CONTROL ECU (MASTER CYLINDER SOLENOID))


    C213407E26
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A36-1 (CANH) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    A36-4 (CANL) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 7
OK


6.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)


    C213407E27
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A36-3 (CANH) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    A36-6 (CANL) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 9
OK

REPAIR OR REPLACE NO. 1 JUNCTION CONNECTOR 

7.CONNECT CONNECTOR
  1. Reconnect the A36 No. 1 junction connector connector.


NEXT


8.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (SKID CONTROL ECU (MASTER CYLINDER SOLENOID))


    C217218E01
  1. Disconnect the A6 skid control ECU (master cylinder solenoid) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A6-11 (CANH) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    A6-25 (CANL) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU (Master Cylinder Solenoid))
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SKID CONTROL ECU (MASTER CYLINDER SOLENOID) (CANH, CANL)
OK

REPLACE SKID CONTROL ECU (MASTER CYLINDER SOLENOID) (Click here)  

9.CONNECT CONNECTOR
  1. Reconnect the A36 No. 1 junction connector connector.


NEXT


10.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (COMBINATION METER ASSEMBLY)


    C217223E01
  1. Disconnect the F14 combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F14-1 (CANH) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    F14-2 (CANL) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Combination Meter Assembly)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (CANH, CANL)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)  

11.CONNECT CONNECTOR
  1. Reconnect the A36 No. 1 junction connector connector.


NEXT


12.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)


    C213407E39
  1. Disconnect the F59 No. 2 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F59-3 (CANH) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    F59-14 (CANL) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)
OK


13.CONNECT CONNECTOR
  1. Reconnect the F59 No. 2 junction connector connector.


NEXT


14.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR SIDE)


    H102621E60
  1. Disconnect the F60 No. 3 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F13-6 (CANH) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    F13-14 (CANL) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of DLC3



NG
Go to step 36
OK


15.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

HINT:
For vehicles without a smart key system, go to "Check for Short to B+ in CAN Bus Wire (No. 3 Junction Connector - Air Conditioning Amplifier Assembly)".



    C213407E40
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F60-6 (CANH) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    F60-17 (CANL) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 22
OK


16.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - POWER MANAGEMENT CONTROL ECU)


    C213407E41
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F60-4 (CANH) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    F60-15 (CANL) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 24
OK


17.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)

HINT:
For vehicles with a smart key system, go to "Check for Short to B+ in CAN Bus Wire (No. 3 Junction Connector - Four Wheel Drive Control ECU)".



    C213407E42
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F60-8 (CANH) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    F60-19 (CANL) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 26
OK


18.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - FOUR WHEEL DRIVE CONTROL ECU)

HINT:
For vehicles without four wheel drive, go to "Check for Short to B+ in CAN Bus Wire (No. 3 Junction Connector - Power Steering ECU Assembly)".



    C213407E43
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F60-3 (CANH) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    F60-14 (CANL) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 28
OK


19.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)


    C213407E44
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F60-5 (CANH) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    F60-16 (CANL) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 30
OK


20.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - YAW RATE SENSOR ASSEMBLY)


    C213407E45
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F60-7 (CANH) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    F60-18 (CANL) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 32
OK


21.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - ECM)


    C213407E46
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F60-2 (CANH) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    F60-13 (CANL) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 34
OK

REPAIR OR REPLACE NO. 3 JUNCTION CONNECTOR 

22.CONNECT CONNECTOR
  1. Reconnect the F60 No. 3 junction connector connector.


NEXT


23.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))


    C217227E01
  1. Disconnect the F79 certification ECU (smart key ECU assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F79-9 (CANH) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    F79-10 (CANL) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Certification ECU (Smart Key ECU Assembly))
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (CANH, CANL)
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (Click here)  

24.CONNECT CONNECTOR
  1. Reconnect the F60 No. 3 junction connector connector.


NEXT


25.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (POWER MANAGEMENT CONTROL ECU)


    C217219E02
  1. Disconnect the F80 power management control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F80-14 (CA1H) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    F80-13 (CA1L) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Power Management Control ECU)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POWER MANAGEMENT CONTROL ECU (CA1H, CA1L)
OK

REPLACE POWER MANAGEMENT CONTROL ECU (Click here)  

26.CONNECT CONNECTOR
  1. Reconnect the F60 No. 3 junction connector connector.


NEXT


27.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY)


    C217223E03
  1. Disconnect the F42 air conditioning amplifier assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F42-11 (CANH) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    F42-12 (CANL) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Air Conditioning Amplifier Assembly)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIR CONDITIONING AMPLIFIER ASSEMBLY (CANH, CANL)
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)  

28.CONNECT CONNECTOR
  1. Reconnect the F60 No. 3 junction connector connector.


NEXT


29.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (FOUR WHEEL DRIVE CONTROL ECU)


    C217223E02
  1. Disconnect the F47 four wheel drive control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F47-19 (CANH) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    F47-20 (CANL) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Four Wheel Drive Control ECU)
    *b
    Front view of DLC3
    Result 
    Result
    Proceed to
    OK (for VF2A)
    A
    OK (for VF4BM)
    B
    OK (for VF2BM)
    C
    NG
    D



B
REPLACE FOUR WHEEL DRIVE CONTROL ECU (Click here)

C
REPLACE FOUR WHEEL DRIVE CONTROL ECU (Click here)

D
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO FOUR WHEEL DRIVE CONTROL ECU (CANH, CANL)
A

REPLACE FOUR WHEEL DRIVE CONTROL ECU (Click here)  

30.CONNECT CONNECTOR
  1. Reconnect the F60 No. 3 junction connector connector.


NEXT


31.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (POWER STEERING ECU ASSEMBLY)


    C217222E01
  1. Disconnect the F41 power steering ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F41-1 (CANH) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    F41-2 (CANL) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Power Steering ECU Assembly)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POWER STEERING ECU ASSEMBLY (CANH, CANL)
OK

REPLACE POWER STEERING ECU ASSEMBLY (Click here)  

32.CONNECT CONNECTOR
  1. Reconnect the F60 No. 3 junction connector connector.


NEXT


33.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (YAW RATE SENSOR ASSEMBLY)


    C217220E01
  1. Disconnect the F36 yaw rate sensor assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F36-3 (CANH) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    F36-2 (CANL) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Yaw Rate Sensor Assembly)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO YAW RATE SENSOR ASSEMBLY (CANH, CANL)
OK

REPLACE YAW RATE SENSOR ASSEMBLY (Click here)  

34.CONNECT CONNECTOR
  1. Reconnect the F60 No. 3 junction connector connector.


NEXT


35.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ECM)
C217225E20
  1. Disconnect the F50 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F50-32 (CANH) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    F50-31 (CANL) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to ECM)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)
OK

REPLACE ECM (Click here)  

36.CONNECT CONNECTOR
  1. Reconnect the F60 No. 3 junction connector connector.


NEXT


37.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)


    C213407E81
  1. Disconnect the G13 No. 4 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G13-5 (CANH) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    G13-16 (CANL) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 4 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 4 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)
OK


38.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 JUNCTION CONNECTOR SIDE)


    C213407E86
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G13-6 (CANH) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    G13-17 (CANL) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 4 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 45
OK


39.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 JUNCTION CONNECTOR - NAVIGATION RECEIVER ASSEMBLY)

HINT:
For vehicles without a navigation receiver assembly, go to "Check for Short to B+ in CAN Bus Wire (No. 4 Junction Connector - Radio and Display Receiver Assembly)".



    C213407E38
  1. Disconnect the G14 No. 4 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G14-6 (CANH) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    G14-17 (CANL) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 4 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 41
OK


40.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)


    C213407E38
  1. Disconnect the G14 No. 4 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G14-6 (CANH) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    G14-17 (CANL) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 4 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 43
OK

REPAIR OR REPLACE NO. 4 JUNCTION CONNECTOR 

41.CONNECT CONNECTOR
  1. Reconnect the G13 and G14 No. 4 junction connector connectors.


NEXT


42.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NAVIGATION RECEIVER ASSEMBLY)


    C248066E03
  1. Disconnect the G37 navigation receiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G37-9 (CANH) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    G37-10 (CANL) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Navigation Receiver Assembly)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO NAVIGATION RECEIVER ASSEMBLY (CANH, CANL)
OK

REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)  

43.CONNECT CONNECTOR
  1. Reconnect the G13 and G14 No. 4 junction connector connectors.


NEXT


44.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY)


    C248066E06
  1. Disconnect the G49 radio and display receiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G49-9 (CANH) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    G49-10 (CANL) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Radio and Display Receiver Assembly)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO RADIO AND DISPLAY RECEIVER ASSEMBLY (CANH, CANL)
OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)  

45.CONNECT CONNECTOR
  1. Reconnect the G13 No. 4 junction connector connector.


NEXT


46.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - NO. 4 JUNCTION CONNECTOR)


    C213407E28
  1. Disconnect the F59 No. 2 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F59-1 (CANH) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    F59-12 (CANL) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 JUNCTION CONNECTOR - NO. 4 JUNCTION CONNECTOR)
OK


47.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - STABILIZER CONTROL ECU)

HINT:
For vehicles without a kinetic dynamic suspension system, go to "Check for Short to B+ in CAN Bus Wire (No. 2 Junction Connector - Main Body ECU (Multiplex Network Body ECU))".



    C213407E29
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F59-6 (CANH) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    F59-17 (CANL) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 51
OK


48.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))


    C213407E30
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F59-2 (CANH) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    F59-13 (CANL) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 53
OK


49.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)


    C213407E31
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F59-5 (CANH) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    F59-16 (CANL) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 55
OK


50.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - STEERING ANGLE SENSOR (SPIRAL CABLE SUB-ASSEMBLY))


    C213407E32
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F59-7 (CANH) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    F59-18 (CANL) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 57
OK

REPAIR OR REPLACE NO. 2 JUNCTION CONNECTOR 

51.CONNECT CONNECTOR
  1. Reconnect the F59 No. 2 junction connector connector.


NEXT


52.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (STABILIZER CONTROL ECU)


    C217314E01
  1. Disconnect the F70 stabilizer control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F70-29 (CANH) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    F70-28 (CANL) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Stabilizer Control ECU)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BUS BRANCH WIRE CONNECTED TO STABILIZER CONTROL ECU (CANH, CANL)
OK

REPLACE STABILIZER CONTROL ECU (Click here)  

53.CONNECT CONNECTOR
  1. Reconnect the F59 No. 2 junction connector connector.


NEXT


54.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))


    C217219E01
  1. Disconnect the F9 main body ECU (multiplex network body ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F9-14 (CANH) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    F9-13 (CANL) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Main Body ECU (Multiplex Network Body ECU))
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (CANH, CANL)
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)  

55.CONNECT CONNECTOR
  1. Reconnect the F59 No. 2 junction connector connector.


NEXT


56.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (AIRBAG SENSOR ASSEMBLY)


    C217224E01
  1. Disconnect the F33 airbag sensor assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F33-13 (CANH) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    F33-22 (CANL) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Airbag Sensor Assembly)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIRBAG SENSOR ASSEMBLY (CANH, CANL)
OK

REPLACE AIRBAG SENSOR ASSEMBLY (Click here)  

57.CONNECT CONNECTOR
  1. Reconnect the F59 No. 2 junction connector connector.


NEXT


58.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (STEERING ANGLE SENSOR (SPIRAL CABLE SUB-ASSEMBLY))


    C217221E01
  1. Disconnect the F19 steering angle sensor (spiral cable sub-assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F19-4 (CANH) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    F19-3 (CANL) - F13-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Steering Angle Sensor (Spiral Cable Sub-assembly))
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO STEERING ANGLE SENSOR (SPIRAL CABLE SUB-ASSEMBLY) (CANH, CANL)
OK

REPLACE STEERING ANGLE SENSOR (SPIRAL CABLE SUB-ASSEMBLY) (Click here)