CAN COMMUNICATION SYSTEM > Short to GND in CAN Bus Line |
| Symptom | Trouble Area |
| The resistance between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of the DLC3 is below 200 Ω. |
|




| 1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and branch wire.
| NEXT | |
| 2.CHECK FOR SHORT TO GND IN CAN BUS WIRE (DLC3 BRANCH WIRE) |
![]() |
Disconnect the F59 No. 2 junction connector connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F13-6 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| F13-14 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Front view of DLC3 |
|
| ||||
| OK | |
| 3.CONNECT CONNECTOR |
Reconnect the F59 No. 2 junction connector connector.
| NEXT | |
| 4.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR SIDE) |
![]() |
Disconnect the A36 No. 1 junction connector connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F13-6 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| F13-14 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Front view of DLC3 |
|
| ||||
| OK | |
| 5.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - SKID CONTROL ECU (MASTER CYLINDER SOLENOID)) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A36-1 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| A36-4 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to No. 1 Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | |
| 6.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A36-3 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| A36-6 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to No. 1 Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | ||
| ||
| 7.CONNECT CONNECTOR |
Reconnect the A36 No. 1 junction connector connector.
| NEXT | |
| 8.CHECK FOR SHORT TO GND IN CAN BUS WIRE (SKID CONTROL ECU (MASTER CYLINDER SOLENOID)) |
![]() |
Disconnect the A6 skid control ECU (master cylinder solenoid) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A6-11 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| A6-25 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Front view of wire harness connector (to Skid Control ECU (Master Cylinder Solenoid)) |
| *b | Front view of DLC3 |
|
| ||||
| OK | ||
| ||
| 9.CONNECT CONNECTOR |
Reconnect the A36 No. 1 junction connector connector.
| NEXT | |
| 10.CHECK FOR SHORT TO GND IN CAN BUS WIRE (COMBINATION METER ASSEMBLY) |
![]() |
Disconnect the F14 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F14-1 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| F14-2 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to Combination Meter Assembly) |
| *b | Front view of DLC3 |
|
| ||||
| OK | ||
| ||
| 11.CONNECT CONNECTOR |
Reconnect the A36 No. 1 junction connector connector.
| NEXT | |
| 12.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR) |
![]() |
Disconnect the F59 No. 2 junction connector connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F59-3 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| F59-14 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | |
| 13.CONNECT CONNECTOR |
Reconnect the F59 No. 2 junction connector connector.
| NEXT | |
| 14.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR SIDE) |
![]() |
Disconnect the F60 No. 3 junction connector connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F13-6 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| F13-14 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Front view of DLC3 |
|
| ||||
| OK | |
| 15.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F60-6 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| F60-17 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to No. 3 Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | |
| 16.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - POWER MANAGEMENT CONTROL ECU) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F60-4 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| F60-15 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to No. 3 Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | |
| 17.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F60-8 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| F60-19 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to No. 3 Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | |
| 18.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - FOUR WHEEL DRIVE CONTROL ECU) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F60-3 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| F60-14 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to No. 3 Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | |
| 19.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F60-5 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| F60-16 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to No. 3 Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | |
| 20.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - YAW RATE SENSOR ASSEMBLY) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F60-7 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| F60-18 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to No. 3 Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | |
| 21.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - ECM) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F60-2 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| F60-13 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to No. 3 Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | ||
| ||
| 22.CONNECT CONNECTOR |
Reconnect the F60 No. 3 junction connector connector.
| NEXT | |
| 23.CHECK FOR SHORT TO GND IN CAN BUS WIRE (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)) |
![]() |
Disconnect the F79 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F79-9 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| F79-10 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to Certification ECU (Smart Key ECU Assembly)) |
| *b | Front view of DLC3 |
|
| ||||
| OK | ||
| ||
| 24.CONNECT CONNECTOR |
Reconnect the F60 No. 3 junction connector connector.
| NEXT | |
| 25.CHECK FOR SHORT TO GND IN CAN BUS WIRE (POWER MANAGEMENT CONTROL ECU) |
![]() |
Disconnect the F80 power management control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F80-14 (CA1H) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| F80-13 (CA1L) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to Power Management Control ECU) |
| *b | Front view of DLC3 |
|
| ||||
| OK | ||
| ||
| 26.CONNECT CONNECTOR |
Reconnect the F60 No. 3 junction connector connector.
| NEXT | |
| 27.CHECK FOR SHORT TO GND IN CAN BUS WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY) |
![]() |
Disconnect the F42 air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F42-11 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| F42-12 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to Air Conditioning Amplifier Assembly) |
| *b | Front view of DLC3 |
|
| ||||
| OK | ||
| ||
| 28.CONNECT CONNECTOR |
Reconnect the F60 No. 3 junction connector connector.
| NEXT | |
| 29.CHECK FOR SHORT TO GND IN CAN BUS WIRE (FOUR WHEEL DRIVE CONTROL ECU) |
![]() |
Disconnect the F47 four wheel drive control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F47-19 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| F47-20 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to Four Wheel Drive Control ECU) |
| *b | Front view of DLC3 |
| Result | Proceed to |
| OK (for VF2A) | A |
| OK (for VF4BM) | B |
| OK (for VF2BM) | C |
| NG | D |
|
| ||||
|
| ||||
|
| ||||
| A | ||
| ||
| 30.CONNECT CONNECTOR |
Reconnect the F60 No. 3 junction connector connector.
| NEXT | |
| 31.CHECK FOR SHORT TO GND IN CAN BUS WIRE (POWER STEERING ECU ASSEMBLY) |
![]() |
Disconnect the F41 power steering ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F41-1 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| F41-2 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to Power Steering ECU Assembly) |
| *b | Front view of DLC3 |
|
| ||||
| OK | ||
| ||
| 32.CONNECT CONNECTOR |
Reconnect the F60 No. 3 junction connector connector.
| NEXT | |
| 33.CHECK FOR SHORT TO GND IN CAN BUS WIRE (YAW RATE SENSOR ASSEMBLY) |
![]() |
Disconnect the F36 yaw rate sensor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F36-3 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| F36-2 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Front view of wire harness connector (to Yaw Rate Sensor Assembly) |
| *b | Front view of DLC3 |
|
| ||||
| OK | ||
| ||
| 34.CONNECT CONNECTOR |
Reconnect the F60 No. 3 junction connector connector.
| NEXT | |
| 35.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECM) |
![]() |
Disconnect the F50 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F50-32 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| F50-31 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to ECM) |
| *b | Front view of DLC3 |
|
| ||||
| OK | ||
| ||
| 36.CONNECT CONNECTOR |
Reconnect the F60 No. 3 junction connector connector.
| NEXT | |
| 37.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR) |
![]() |
Disconnect the G13 No. 4 junction connector connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| G13-5 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| G13-16 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to No. 4 Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | |
| 38.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 JUNCTION CONNECTOR SIDE) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| G13-6 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| G13-17 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to No. 4 Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | |
| 39.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 JUNCTION CONNECTOR - NAVIGATION RECEIVER ASSEMBLY) |
![]() |
Disconnect the G14 No. 4 junction connector connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| G14-6 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| G14-17 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to No. 4 Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | |
| 40.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY) |
![]() |
Disconnect the G14 No. 4 junction connector connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| G14-6 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| G14-17 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to No. 4 Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | ||
| ||
| 41.CONNECT CONNECTOR |
Reconnect the G13 and G14 No. 4 junction connector connectors.
| NEXT | |
| 42.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NAVIGATION RECEIVER ASSEMBLY) |
Disconnect the G37 navigation receiver assembly connector.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| G37-9 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| G37-10 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Front view of wire harness connector (to Navigation Receiver Assembly) |
| *b | Front view of DLC3 |
|
| ||||
| OK | ||
| ||
| 43.CONNECT CONNECTOR |
Reconnect the G13 and G14 No. 4 junction connector connectors.
| NEXT | |
| 44.CHECK FOR SHORT TO GND IN CAN BUS WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY) |
Disconnect the G49 radio and display receiver assembly connector.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| G49-9 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| G49-10 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Front view of wire harness connector (to Radio and Display Receiver Assembly) |
| *b | Front view of DLC3 |
|
| ||||
| OK | ||
| ||
| 45.CONNECT CONNECTOR |
Reconnect the G13 No. 4 junction connector connector.
| NEXT | |
| 46.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - NO. 4 JUNCTION CONNECTOR) |
![]() |
Disconnect the F59 No. 2 junction connector connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F59-1 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| F59-12 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | |
| 47.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - STABILIZER CONTROL ECU) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F59-6 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| F59-17 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | |
| 48.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F59-2 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| F59-13 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | |
| 49.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F59-5 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| F59-16 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | |
| 50.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - STEERING ANGLE SENSOR (SPIRAL CABLE SUB-ASSEMBLY)) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F59-7 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| F59-18 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | ||
| ||
| 51.CONNECT CONNECTOR |
Reconnect the F59 No. 2 junction connector connector.
| NEXT | |
| 52.CHECK FOR SHORT TO GND IN CAN BUS WIRE (STABILIZER CONTROL ECU) |
![]() |
Disconnect the F70 stabilizer control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F70-29 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| F70-28 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to Stabilizer Control ECU) |
| *b | Front view of DLC3 |
|
| ||||
| OK | ||
| ||
| 53.CONNECT CONNECTOR |
Reconnect the F59 No. 2 junction connector connector.
| NEXT | |
| 54.CHECK FOR SHORT TO GND IN CAN BUS WIRE (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)) |
![]() |
Disconnect the F9 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F9-14 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| F9-13 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to Main Body ECU (Multiplex Network Body ECU)) |
| *b | Front view of DLC3 |
|
| ||||
| OK | ||
| ||
| 55.CONNECT CONNECTOR |
Reconnect the F59 No. 2 junction connector connector.
| NEXT | |
| 56.CHECK FOR SHORT TO GND IN CAN BUS WIRE (AIRBAG SENSOR ASSEMBLY) |
![]() |
Disconnect the F33 airbag sensor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F33-13 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| F33-22 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Front view of wire harness connector (to Airbag Sensor Assembly) |
| *b | Front view of DLC3 |
|
| ||||
| OK | ||
| ||
| 57.CONNECT CONNECTOR |
Reconnect the F59 No. 2 junction connector connector.
| NEXT | |
| 58.CHECK FOR SHORT TO GND IN CAN BUS WIRE (STEERING ANGLE SENSOR (SPIRAL CABLE SUB-ASSEMBLY)) |
![]() |
Disconnect the F19 steering angle sensor (spiral cable sub-assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F19-4 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| F19-3 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to Steering Angle Sensor (Spiral Cable Sub-assembly)) |
| *b | Front view of DLC3 |
|
| ||||
| OK | ||
| ||