Home › Engine / Hybrid System › 3ZR-FAE (ENGINE MECHANICAL) › ENGINE UNIT › from 2019.09
RM32H0E _51 Engine / Hybrid System _059726 3ZR-FAE ENGINE MECHANICAL _0294289 ENGINE UNIT A

3ZR-FAE ENGINE MECHANICAL  ENGINE UNIT  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL STIFFENING CRANKCASE RING PIN

NOTICE:

It is not necessary to remove ring pins unless they are being replaced.


a.
A394344C01
2.958,2.438 3.271,2.594 0.313,0.156 10 false *a 0.76,2.188 1.073,2.344 0.313,0.156 10 false *b 1.385,2.708 1.698,2.865 0.313,0.156 10 false *c
*a Protrusion Height
*b 11 mm
*c 8 mm


Using a plastic hammer, tap 2 new ring pins into the stiffening crankcase assembly.

Standard Ring Pin:
Item Protrusion Height Height Width
Ring pin 4.0 mm (0.157 in.) 8.0 mm (0.315 in.) 11 mm (0.433 in.)



b.
A152991C06
2.938,2.385 3.25,2.542 0.313,0.156 10 *a 0.635,2.083 0.948,2.24 0.313,0.156 10 *b 1.292,2.656 1.604,2.813 0.313,0.156 10 *c
*a Protrusion Height
*b 11 mm (0.433 in.)
*c 8 mm (0.315 in.)


Using a plastic hammer, tap in 2 new stiffening crankcase ring pins until they are seated.

Standard Ring Pin:
Item Protrusion Height Height Width
Stiffening crankcase ring pin 3.0 mm (0.118 in.) 8 mm (0.315 in.) 11 mm (0.433 in.)



Hide 2.INSTALL STUD BOLT

NOTICE:

If a stud bolt is deformed or the threads are damaged, replace it.


a.
A150942C02
2.667,2.104 2.5,2.104 2.5,2.104 2.333,1.771 true 0.417,1.948 0.583,1.948 0.583,1.948 0.75,1.615 true 2.25,2.75 2.708,2.927 0.458,0.177 10 *c 1.625,2.688 1.792,2.917 0.167,0.229 10 *a 1.615,3.01 1.927,3.229 0.313,0.219 10 *b 2.708,2.021 3.021,2.177 0.313,0.156 10 *1 0.26,1.885 0.573,2.042 0.313,0.156 10 *1
*1 Stud Bolt
*a 8.5 mm (0.335 in.)
*b 8.0 mm (0.315 in.)
*c 18 mm (0.709 in.)


Using an E6 "TORX" socket wrench, install the stud bolts as shown in the illustration.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


b.
A150941C03
2.688,2.656 2.896,2.865 0.208,0.208 10 *c 2.26,2.365 2.479,2.542 0.219,0.177 10 *a 2.25,2.938 2.448,3.125 0.198,0.188 10 *b
*a 15 mm (0.591 in.)
*b 12 mm (0.472 in.)
*c 34 mm (1.339 in.)


Using an E6 "TORX" socket wrench, install the stud bolts as shown in the illustration.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


c.
A298932C01
1.51,2.5 1.823,2.656 0.313,0.156 10 *a 1.542,3.01 1.854,3.167 0.313,0.156 10 *b 2.479,2.719 2.792,2.875 0.313,0.156 10 *c
*a 12 mm (0.472 in.)
*b 9.0 mm (0.354 in.)
*c 23 mm (0.906 in.)


Using an E5 "TORX" socket wrench, install the stud bolts as shown in the illustration.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


d.
A173608C01
0.958,3.719 1.24,3.938 0.281,0.219 10 *a 1.698,3.438 1.927,3.656 0.229,0.219 10 *b 1.385,4.042 1.583,4.229 0.198,0.188 10 *c
*a 12 mm (0.472 in.)
*b 18 mm (0.709 in.)
*c 48.5 mm (1.909 in.)


Using an E7 "TORX" socket wrench, install the camshaft housing stud bolts.

Torque:
9.5 N*m (97 kgf*cm, 84 in.*lbf)


Hide 11420 3.INSTALL STIFFENING CRANKCASE ASSEMBLY

a.
A150919N23
0.583,2.635 0.844,2.854 0.26,0.219 10 false A

Apply seal packing in a continuous line as shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard Seal Diameter:
Area Specified Condition
Continuous Line 2.0 to 3.0 mm (0.0787 to 0.118 in.)
A 4.5 to 5.5 mm (0.177 to 0.217 in.)


Application Length (A):

56 mm (2.20 in.)


NOTICE:
·

Remove any oil from the contact surfaces.

·

Install the stiffening crankcase assembly within 3 minutes and tighten the bolts within 15 minutes of applying seal packing.

·

Do not start the engine for at least 2 hours after installing the stiffening crankcase assembly.




b.
A152989E06
0.792,0.188 0.938,0.365 0.146,0.177 10 false B 1.344,0.198 1.49,0.375 0.146,0.177 10 false B 1.688,0.219 1.833,0.396 0.146,0.177 10 false B 2.167,0.302 2.313,0.479 0.146,0.177 10 false C 2.344,2.146 2.49,2.323 0.146,0.177 10 false C 1.802,2.146 1.948,2.323 0.146,0.177 10 false C 1.719,2.396 1.865,2.573 0.146,0.177 10 false 2 1.385,4.365 1.531,4.542 0.146,0.177 10 false 1 1.365,2.177 1.51,2.354 0.146,0.177 10 false C 0.979,2.188 1.125,2.365 0.146,0.177 10 false C 0.615,2.188 0.76,2.365 0.146,0.177 10 false C 3.115,0.698 3.26,0.875 0.146,0.177 10 false A 3.104,1.625 3.25,1.802 0.146,0.177 10 false A 3.135,2.896 3.24,3.042 0.104,0.146 10 false 9 1.823,4.354 1.938,4.5 0.115,0.146 10 false 3 1.365,2.375 1.458,2.531 0.094,0.156 10 false 4 1.01,4.354 1.125,4.5 0.115,0.146 10 false 5 2.188,2.49 2.302,2.646 0.115,0.156 10 false 6 2.375,4.323 2.5,4.479 0.125,0.156 10 false 7 0.823,2.375 0.917,2.521 0.094,0.146 10 false 8 0.604,4.365 0.781,4.51 0.177,0.146 10 false 10 3.115,3.823 3.292,3.969 0.177,0.146 10 false 11

Install the stiffening crankcase assembly with the 11 bolts in the order shown in the illustration.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

Bolt Length:
Item Specified Condition
Bolt (A) 143.7 mm (5.43 in.)
Bolt (B) 35 mm (1.38 in.)
Bolt (C) 70 mm (2.76 in.)



c.

Recheck the torque for the bolts (1) and (2).

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


d.

Wipe off any excess seal packing with a clean piece of cloth.


Hide 15100 4.INSTALL OIL PUMP ASSEMBLY

Hide 12102A 5.INSTALL NO. 2 OIL PAN SUB-ASSEMBLY

Hide 12101A 6.INSTALL OIL PAN DRAIN PLUG

a.
A150893

Install a new gasket and oil pan drain plug to the No. 2 oil pan sub-assembly.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


Hide 11432A 8.INSTALL NO. 1 TAPER SCREW PLUG

a.
A235914C12
1.833,0.5 2.031,0.427 false 1.49,1.698 1.802,1.604 true 2.583,2.531 2.823,2.677 0.24,0.146 10 false *d 0.448,2.396 0.875,2.604 0.427,0.208 10 false A 2.042,2.24 2.469,2.396 0.427,0.156 10 false B 2.948,2.729 3.125,2.885 0.177,0.156 10 false *f 0.938,2.635 1.177,2.781 0.24,0.146 10 false *a 0.938,2.948 1.125,3.115 0.188,0.167 10 false *b 1.26,2.823 1.438,2.969 0.177,0.146 10 false *c 1.656,0.406 1.844,0.656 0.188,0.25 10 false A 1.323,1.594 1.688,1.813 0.365,0.219 10 false B 2.573,2.906 2.813,3.052 0.24,0.146 10 false *e
*a 5.0 mm (0.197 in.)
*b 11 mm (0.433 in.)
*c 18 mm (0.709 in.)
*d 8.0 mm (0.315 in.)
*e 12.5 mm (0.492 in.)
*f 22 mm (0.866 in.)


Apply adhesive to 2 or 3 threads of the No. 1 taper screw plug, and install the No. 1 taper screw plug (A).

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent


NOTICE:
·

Install the No. 1 taper screw plug within 3 minutes of applying adhesive.

·

Do not start the engine for at least 1 hour after installing the No. 1 taper screw plug.




b.

Apply adhesive to 2 or 3 threads of the No. 1 taper screw plug, and install the No. 1 taper screw plug (B).

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:
·

Install the No. 1 taper screw plug within 3 minutes of applying adhesive.

·

Do not start the engine for at least 1 hour after installing the No. 1 taper screw plug.




Hide 12204 9.INSTALL PCV VALVE (VENTILATION VALVE SUB-ASSEMBLY)

Hide 11101 11.INSTALL CYLINDER HEAD SUB-ASSEMBLY

Hide 13716 12.INSTALL VALVE STEM CAP

a.

Apply a light coat of engine oil to the valve stem ends.


b.

Install the 16 valve stem caps to the valve stems.

HINT:

Do not drop the valve stem caps into the cylinder head sub-assembly.



Hide 13750 13.INSTALL VALVE LASH ADJUSTER ASSEMBLY

a.

Inspect each valve lash adjuster assembly before installing it.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE MECHANICAL)>ENGINE UNIT>INSPECTION


b.

Install the 16 valve lash adjuster assemblies to the cylinder head sub-assembly.

NOTICE:

Install the valve lash adjuster assembly to the same place it was removed from.



Hide 13801 14.INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.
A226182C03
2.146,0.802 2.469,0.479 2.469,0.479 2.844,0.479 false 2.094,1.26 2.802,1.26 false 1.552,0.469 1.302,0.219 1.302,0.219 0.667,0.219 false 1.083,1.271 0.417,1.271 false 0.25,1.219 0.469,1.458 0.219,0.24 10 *1 0.458,0.146 0.698,0.354 0.24,0.208 10 *2 2.854,1.188 3.156,1.594 0.302,0.406 10 *3 2.875,0.417 3.229,0.833 0.354,0.417 10 *4
*1 Valve Lash Adjuster Assembly
*2 No. 1 Valve Rocker Arm Sub-assembly
*3 Valve Stem
*4 Valve Stem Cap


Apply engine oil to the valve lash adjuster assembly tips and valve stem cap ends.


b.

Make sure that the No. 1 valve rocker arm sub-assemblies are installed as shown in the illustration.


Hide 11114A 15.INSTALL CAMSHAFT HOUSING STRAIGHT PIN

NOTICE:

It is not necessary to remove a camshaft housing straight pin unless it is being replaced.


a.
A206181C01
1.135,2.385 1.448,2.542 0.313,0.156 10 *a 2.729,2.417 3.042,2.573 0.313,0.156 10 *b 2.229,2.979 2.542,3.135 0.313,0.156 10 *c
*a Protrusion Height
*b 14 mm (0.551 in.)
*c 6.0 mm (0.236 in.)


Using a plastic hammer, tap in a new camshaft housing straight pin to the specified protrusion height.

Standard Straight Pin:
Item Protrusion Height Height Width
Camshaft housing straight pin 6.5 to 7.5 mm (0.256 to 0.295 in.) 14 mm (0.551 in.) 6.0 mm (0.236 in.)



Hide 222A0 16.INSTALL CONTINUOUSLY VARIABLE VALVE LIFT CONTROLLER ASSEMBLY

Hide 11103 17.INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY

Hide 13050 18.INSTALL CAMSHAFT TIMING GEAR ASSEMBLY

Hide 13070A 19.INSTALL CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

Hide 13521A 20.INSTALL CRANKSHAFT TIMING GEAR KEY

a.
A150910

Using a plastic hammer, tap in the 2 crankshaft timing gear keys.

HINT:

Tap in the crankshaft timing gear keys until they contact the crankshaft as shown in the illustration.



Hide 19315 21.INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE

a.
A150874

Install the No. 1 crankshaft position sensor plate with the "F" mark facing forward.


Hide 13507 22.INSTALL NO. 2 CHAIN SUB-ASSEMBLY

Hide 13521 23.INSTALL CRANKSHAFT TIMING SPROCKET

Hide 13561 24.INSTALL NO. 1 CHAIN VIBRATION DAMPER

a.
A173475

Install the No. 1 chain vibration damper with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 25.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.

Temporarily install the crankshaft pulley bolt.


b.
A309090C01
1.719,1.583 1.844,0.302 1.844,0.302 2.094,0.302 true 2.156,0.229 2.469,0.427 0.313,0.198 10 false *1
*1 Timing Gear Key


Turn the crankshaft counterclockwise to position the timing gear key to the top.


c.
A282746C09
0.469,0.792 1,1.438 1,1.438 1.594,0.833 false 0.906,1.458 1.083,1.625 0.177,0.167 10 *a
*a Timing Mark


Check that the timing marks on the camshaft timing exhaust gear assembly and camshaft timing gear assembly are aligned as shown in the illustration.


d.

Remove the crankshaft pulley bolt.


Hide 13506 26.INSTALL CHAIN SUB-ASSEMBLY

a.

Align the mark plates (orange) with the timing marks as shown in the illustration and install the chain sub-assembly.

A282747C04
0.833,2.51 1.427,1.792 1.427,1.792 1.531,1.792 true 3.896,0.552 3.063,0.552 true 3.896,0.438 3.323,0.219 3.323,0.219 3.052,0.219 true 0.865,2.698 1.427,3.344 1.427,3.344 1.573,3.344 true 1.563,1.729 1.771,2.021 0.208,0.292 10 *a 1.656,3.26 1.844,3.469 0.188,0.208 10 *b 2.896,0.146 3.281,0.5 0.385,0.354 10 *a 2.896,0.479 3.177,0.823 0.281,0.344 10 *b
*a Mark Plate (Orange) *b Timing Mark


HINT:
·

Be sure to position the mark plate at the front of the engine.

·

The mark plate on the camshaft side is colored orange.

·

Do not pass the chain sub-assembly around the sprocket of the camshaft timing gear assembly. Only place it on the sprocket.

·

Pass the chain sub-assembly through the No. 1 chain vibration damper.




b.

Hold the hexagonal portion of the camshaft with a wrench and turn the camshaft timing gear assembly counterclockwise to align the mark plate (orange) and timing mark, and then install the chain sub-assembly.


c.

Hold the hexagonal portion of the camshaft with a wrench and turn the camshaft timing gear assembly clockwise.

HINT:

To tension the chain sub-assembly, slowly turn the camshaft timing gear assembly clockwise to prevent the chain sub-assembly from being misaligned.



d.
A172418C06
1.948,1.76 1.229,0.365 1.229,0.365 1.104,0.365 true 1.823,1.833 1.229,0.365 true 1.917,2.021 2.531,3.125 2.531,3.125 2.677,3.125 true 2.146,1.844 2.531,3.125 true 2.688,3.031 2.875,3.208 0.188,0.177 10 false *b 0.896,0.271 1.052,0.417 0.156,0.146 10 false *a
*a Timing Mark
*b Mark Plate (Pink)


Align the mark plates (pink) and timing marks and install the chain to the crankshaft timing gear.

HINT:

The mark plates on the crankshaft side are colored pink.



Hide 13559 27.INSTALL CHAIN TENSIONER SLIPPER

A173477

a.

Install the chain tensioner slipper to the cylinder block sub-assembly.


Hide 28.CHECK NO. 1 CYLINDER TO TDC/COMPRESSION

a.

Check each timing mark at TDC/compression.

A165311C03
0.771,1.375 0.969,0.938 0.969,0.938 1.135,0.938 true 2.396,1.469 2.396,1.052 2.396,1.052 2.229,1.052 true 0.781,1.469 0.781,2.219 true 2.365,1.594 2.365,2.26 true 5.5,0.833 5.667,0.833 5.667,0.833 5.792,1.635 true 6.25,0.833 6.083,0.833 6.083,0.833 5.854,1.594 true 6.073,2.229 5.906,2.229 5.906,2.229 5.906,1.646 true 5.646,2.302 5.813,2.302 5.813,2.302 5.813,1.719 true 0.719,2.25 1.031,2.406 0.313,0.156 10 false *a 1.177,0.854 1.49,1.01 0.313,0.156 10 false *b 2.073,0.969 2.385,1.125 0.313,0.156 10 false *b 2.292,2.292 2.604,2.448 0.313,0.156 10 false *a 6.292,0.75 6.604,0.906 0.313,0.156 10 false *a 5.323,0.75 5.635,0.906 0.313,0.156 10 false *a 6.115,2.146 6.427,2.302 0.313,0.156 10 false *c 5.5,2.219 5.813,2.375 0.313,0.156 10 false *c
*a Timing Mark *b Mark Plate (Orange)
*c Mark Plate (Pink) - -



Hide 12511 29.INSTALL NO. 1 GENERATOR BRACKET

a.
A394380

Install the No. 1 generator bracket with the 4 bolts.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)


Hide 16323 30.INSTALL WATER INLET HOUSING

a.
A150906

Install a new gasket and the water inlet housing with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 11302 31.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY

Hide 11302A 32.INSTALL TIMING CHAIN COVER OIL SEAL

Hide 13540 34.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A162975C09
0.26,0.156 1.677,1.5 1.417,1.344 1.771,0.167 3.188,1.51 1.417,1.344 1.042,0.271 1.115,0.271 1.115,0.271 1.177,0.323 false 0.875,3.083 0.99,3.083 0.99,3.083 1.052,2.646 false 2.302,3.979 2.25,3.979 2.25,3.979 2.083,3.542 false 1.438,4.281 1.313,4.281 1.313,4.281 1.188,4.042 false 0.969,3.479 1.052,3.479 1.052,3.479 1.167,3.573 false 1.208,2.115 2.49,2.313 2.49,2.313 2.115,3.198 false 1.375,2.49 1.375,2.688 false 2.458,0.271 2.531,0.271 2.531,0.271 2.594,0.333 false 1.344,2.927 1.292,2.927 1.292,2.927 1.125,2.49 false 0.885,0.208 1.167,0.479 0.281,0.271 10 false *a 0.344,0.677 0.646,1.021 0.302,0.344 10 false *g 1.313,2.688 1.604,3 0.292,0.313 10 false *b 0.75,1.948 1.052,2.292 0.302,0.344 10 false *h 2.333,3.927 2.573,4.167 0.24,0.24 10 false *c 0.313,0.198 0.594,0.479 0.281,0.281 10 false *e 1.833,0.188 2.125,0.51 0.292,0.323 10 false *f 2.292,0.198 2.583,0.5 0.292,0.302 10 false *a 2.552,2.208 2.802,2.448 0.25,0.24 10 false *a 0.833,3.417 1.073,3.698 0.24,0.281 10 false *a 1.458,4.219 1.792,4.531 0.333,0.313 10 false *b 0.677,3.01 0.99,3.385 0.313,0.375 10 false *d 1.833,0.688 2.063,0.927 0.229,0.24 10 false *g 0.531,2.281 0.875,2.729 0.344,0.448 10 false *g 1.375,2.885 1.615,3.125 0.24,0.24 10 false *c
*a Cam
*b Hook
*c Plunger
*d Pin
*e Correct
*f Incorrect
*g Push
*h Raise


Raise the cam, then fully push in the plunger and engage the hook to the pin so that the plunger is in the position shown in the illustration.

NOTICE:

Make sure that the cam engages the first tooth of the plunger to allow the hook to pass over the pin.



b.
A296127

Install a new gasket, the bracket and No. 1 chain tensioner assembly with the 2 nuts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)

NOTICE:

If the hook releases the plunger while the No. 1 chain tensioner assembly is being installed, set the hook again.



c.
A282750C02
0.563,2.229 0.344,2.229 false 0.604,1.771 0.833,2 0.229,0.229 10 *b 0.198,2.177 0.479,2.417 0.281,0.24 10 *a
*a Hook
*b Disconnect


Rotate the crankshaft counterclockwise slightly and check that the hook is released.


d.
A282751C02
0.865,1.958 0.781,1.958 0.781,1.958 0.656,2.344 false 0.906,1.875 1.208,2.167 0.302,0.292 10 *b 0.375,2.625 0.594,2.875 0.219,0.25 10 *a
*a Plunger
*b Plunger Extended


Turn the crankshaft clockwise and check that the plunger is extended.


Hide 15600A 35.INSTALL OIL FILTER UNION

A365984

a.

Using a 12 mm hexagon socket wrench, install the oil filter union to the oil filter bracket.

Torque:
29.5 N*m (301 kgf*cm, 22 ft.*lbf)


Hide 11193 37.INSTALL SPARK PLUG TUBE GASKET

a.
A153838C02
0.51,1.885 0.823,2.083 0.313,0.198 10 *a
*a Part to Cut Off


Using a cutter knife, cut off the seal part of the removed spark plug tube gasket.


b.
A179168C04
1.396,1.083 1.563,1.49 false 1.604,0.646 1.896,0.427 false 1.563,4.115 2.021,3.76 false 1.938,0.344 2.125,0.646 0.188,0.302 10 *1 1.594,1.458 1.823,1.708 0.229,0.25 10 *2 1.396,4.073 1.677,4.323 0.281,0.25 10 *a
*a Claw
*1 Spark Plug Tube Gasket without Seal Part
*2 New Spark Plug Tube Gasket


Using a hammer and the spark plug tube gasket which has had the sealing part cut off, uniformly tap in a new spark plug tube gasket all the way.

NOTICE:
·

Keep the lip free from foreign matter.

·

Do not tap the spark plug tube gasket.



HINT:

If a spark plug tube gasket that will be used to install the spark plug tube gasket is deformed, and cannot be positioned on the spark plug tube gasket, correct the deformation using pliers.



c.

Return the claws of the ventilation baffle plate to their original positions.


Hide 11213 38.INSTALL CYLINDER HEAD COVER GASKET

a.
A179166

Install a new cylinder head cover gasket to the cylinder head cover sub-assembly.

NOTICE:

Remove any oil from the contact surfaces.



Hide 11201 39.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

a.
A165301

Install 3 new gaskets to the camshaft bearing cap.


b.
A165302

Apply seal packing as shown the illustration.

Seal Packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard Diameter:

4.0 mm (0.157 in.)


NOTICE:
·

Remove any oil from the contact surfaces.

·

Install the cylinder head cover sub-assembly within 3 minutes and tighten the bolts within 15 minutes of applying seal packing.

·

Do not start the engine for at least 2 hours after installation.




c.
A173472

Install the cylinder head cover sub-assembly with a new seal washer and the 13 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 83530 40.INSTALL ENGINE OIL PRESSURE SWITCH ASSEMBLY

Hide 89422 41.INSTALL ENGINE COOLANT TEMPERATURE SENSOR

Hide 11101J 44.INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

Hide 47.INSTALL ENGINE COVER JOINT

a.
A150847

Install the 2 engine cover joints.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 12108A 48.INSTALL OIL FILLER CAP GASKET

a.
A128159

Install the oil filler cap gasket to the oil filler cap sub-assembly.


Hide 12108 49.INSTALL OIL FILLER CAP SUB-ASSEMBLY

a.
A173599

Install the oil filler cap sub-assembly.