After starting the engine, this DTC is stored when the engine stops without the ignition switch being operated.
Using the intelligent tester, the conditions present when the DTC was stored can be confirmed by referring to the freeze frame data. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.
It is necessary to check if the vehicle has run out of fuel in the past before performing troubleshooting, as this DTC is also stored when the engine stalls due to running out of fuel.
This DTC is stored if the engine speed drops below the set speed.
Using the intelligent tester, the conditions present when the DTC was stored can be confirmed by referring to the freeze frame data. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.
It is necessary to check if the vehicle has run out of fuel in the past before performing troubleshooting, as this DTC is also stored when idling is unstable due to running out of fuel.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P1603 | Engine Stall History | After monitoring for startability problems (P1604) finishes and 5 seconds or more elapse after starting the engine, with the engine running, the engine stops (the engine speed drops to 200 rpm or less) without the ignition switch being operated for 0.5 seconds or more (1 trip detection logic). | ·
Air leak in intake system ·
Purge VSV ·
Brake booster hose not connected properly ·
Mass air flow meter sub-assembly ·
Engine coolant temperature sensor ·
Wire harness or connector ·
Air fuel ratio sensor ·
Power supply circuit (purge VSV, fuel injector assembly, ignition coil assembly) ·
Fuel pump ·
Fuel pump control system ·
Fuel line (fuel filter, pipes and hoses) ·
Throttle with motor body assembly ·
Camshaft timing oil control valve assembly ·
Air conditioning system ·
Power steering system ·
Electrical load signal system ·
A/T system ·
Park/Neutral position switch assembly ·
Thermostat ·
ECM |
Does not come on | DTC stored |
| P1605 | Rough Idling | After 5 seconds or more elapse after starting the engine, with the engine running, the engine speed drops to 400 rpm or less (1 trip detection logic). | ·
Air leak in intake system ·
Purge VSV ·
Brake booster hose not connected properly ·
Mass air flow meter sub-assembly ·
Engine coolant temperature sensor ·
Wire harness or connector ·
Air fuel ratio sensor ·
Power supply circuit (purge VSV, fuel injector assembly, ignition coil assembly) ·
Fuel pump ·
Fuel pump control system ·
Fuel line (fuel filter, pipes and hoses) ·
Throttle with motor body assembly ·
Camshaft timing oil control valve assembly ·
Knock control sensor ·
Ignition coil assembly (No. 1 to No. 6 cylinder) ·
Fuel injector assembly ·
Spark plug(s) ·
Air conditioning system ·
Power steering system ·
Electrical load signal system ·
A/T system ·
Park/Neutral position switch assembly ·
ECM |
Does not come on | DTC stored |
Reference waveforms showing a normal cold engine start
Reference waveforms showing a normal warm engine start
Reference values when there is an air leak in the intake system during rough idling
| Parameter | -3 | -2 | -1 | 0 | 1 | Unit |
|---|---|---|---|---|---|---|
| Engine Speed | 647 | 649 | 586 | 378 | 182 | rpm |
| Calculate Load | 26.2 | 26.2 | 29.1 | 42.6 | 58.6 | % |
| Vehicle Load | 11.7 | 11.7 | 12.1 | 48.7 | 61.2 | % |
| MAF | 2.87 | 2.87 | 2.87 | 6.23 | 3.04 | gm/sec |
| Atmosphere Pressure | 0 | 0 | 0 | 0 | 0 | kPa |
| Coolant Temp | 187 | 187 | 187 | 187 | 187 | F |
| Intake Air | 109 | 109 | 109 | 109 | 109 | F |
| Battery Voltage | 13.515 | 13.515 | 13.264 | 12.892 | 12.792 | V |
| Throttle Sensor Volt % | 14.5 | 14.5 | 14.5 | 16.8 | 17.2 | % |
| Throttl Sensor #2 Volt % | 46.2 | 46.2 | 46.2 | 48.4 | 49.2 | % |
| Throttle Sensor Position | 0.0 | 0.0 | 0.0 | 0.0 | 0.0 | % |
| Throttle Motor DUTY | 14.5 | 14.5 | 14.5 | 17.2 | 17.2 | % |
| Injector (Port) | 2159 | 2161 | 2148 | 2190 | 2190 | μs |
| Injection Volum (Cylinder 1) | 0.093 | 0.093 | 0.093 | 0.095 | 0.095 | ml |
| Fuel Pump Duty | 58.6 | 58.6 | 58.6 | 58.6 | 58.6 | % |
| EVAP (Purge) VSV | 13.3 | 13.3 | 13.3 | 13.3 | 13.3 | % |
| Evap Purge Flow | 2.9 | 2.9 | 2.9 | 3.2 | 3.2 | % |
| Purge Density Learn Value | 0.891 | 0.891 | 0.891 | 0.891 | 0.891 | |
| EVAP Purge VSV | OFF | OFF | OFF | OFF | OFF | |
| Purge Cut VSV Duty | 8.5 | 8.5 | 8.5 | 8.5 | 8.5 | % |
| Target Air-Fuel Ratio | 0.998 | 0.998 | 0.998 | 0.998 | 0.998 | |
| AF Lambda B1S1 | 0.999 | 0.997 | 1.001 | 1.038 | 1.118 | |
| AF Lambda B2S1 | 0.997 | 0.994 | 0.999 | 1.036 | 1.112 | |
| AFS Voltage B1S1 | 3.258 | 3.242 | 3.284 | 3.521 | 3.715 | V |
| AFS Voltage B2S1 | 3.251 | 3.306 | 3.324 | 3.497 | 3.689 | V |
| O2S B1S2 | 0.740 | 0.740 | 0.740 | 0.740 | 0.740 | V |
| O2S B2S2 | 0.760 | 0.760 | 0.760 | 0.760 | 0.760 | V |
| Short FT #1 | -1.563 | -1.563 | -1.563 | -1.563 | -1.563 | % |
| Long FT #1 | 6.250 | 6.250 | 6.250 | 6.250 | 6.250 | % |
| Total FT #1 | 0.054 | 0.054 | 0.054 | 0.054 | 0.054 | |
| Sort FT #2 | -0.782 | -0.782 | -0.782 | -0.782 | -0.782 | % |
| Long FT #2 | 7.031 | 7.031 | 7.031 | 7.031 | 7.031 | % |
| Total FT #2 | 0.062 | 0.062 | 0.062 | 0.062 | 0.062 | |
| Fuel System Status #1 | CL | CL | CL | CL | CL | |
| Fuel System Status #2 | CL | CL | CL | CL | CL | |
| IGN Advance | 22.0 | 22.0 | 22.5 | 23.5 | 23.5 | deg |
| Knock Feedback Value | -1.5 | -1.5 | -1.5 | -1.5 | -1.5 | °CA |
| Knock Correct Learn Value | 17.0 | 17.0 | 17.0 | 17.0 | 17.0 | °CA |
| Starter Signal | Close | Close | Close | Close | Close |
Refer to DTC P0351 for the ignition coil circuit (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P0351).
Refer to DTC P0443 for the purge VSV circuit (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P0443).
Refer to DTC P2195 for the air fuel ratio sensor circuit (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P2195).
Refer to Fuel Pump Control Circuit (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>Fuel Pump Control Circuit).
Refer to Fuel Injector Circuit (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>Fuel Injector Circuit).
In contrast to normal malfunction diagnosis for components, circuits and systems, DTCs P1603 and P1605 are used to determine the malfunctioning area from the problem symptoms and freeze frame data when the user mentions problems such as engine stall.
As these DTCs can be stored as a result of certain user actions, even if these DTCs are output, if the customer makes no mention of problems, clear these DTCs without performing any troubleshooting and return the vehicle to the customer.
If any other DTCs are output, perform troubleshooting for those DTCs first.
Use any information from the customer problem analysis about the condition of the vehicle at the time when the problem occurred (how the engine stopped, conditions when the engine was restarted, etc.) as a reference.
| Symptom | Suspected Area |
|---|---|
| Engine vibration occurs and engine stops | Air fuel ratio abnormal |
| Engine stops with no engine vibration | Ignition system, injection stoppage, high load from external parts |
| Engine can be started with accelerator pedal depressed | Insufficient air volume |
| Rough idling after engine started | Air fuel ratio abnormal, abnormal combustion |
Read freeze frame data using the intelligent tester. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.
When confirming the freeze frame data, be sure to check all 5 sets of freeze frame data (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA).
When DTC P1603 (Engine Stall History) is stored, DTC P1605 (Rough Idling) is also stored. When confirming freeze frame data, check DTC P1605. (The ECM stores DTC P1605 first. Therefore, the 5 sets of freeze frame data can be confirmed through DTC P1605, enabling the technician to obtain more information.)
When confirming freeze frame data, if there are multiple items related to the cause of the malfunction, perform troubleshooting for all related items.
Try to operate the vehicle under the conditions recorded in the freeze frame data which were present when the malfunction occurred. Confirm the data at this time and the data when the engine is idling (engine warmed up, no load, and shift lever in D or N) and compare these data with the freeze frame data.
Inspections take into account the fact that the malfunction may not have reoccurred and place emphasis on checking the vehicle conditions present at the time when the malfunction occurred.
When performing inspections, jiggle the relevant wire harnesses and connectors in an attempt to reproduce malfunctions that do not always occur.
Using freeze frame data, narrow down the parts to be inspected according to the vehicle conditions at the time when the malfunction occurred.
If the engine stalled when the intake air volume was low (during idling or deceleration), there may be a decrease in torque due to an incorrect air fuel ratio, etc.
If the engine stalled when the intake air volume was high (during driving or acceleration), there may be a major malfunction such as continuous misfire due to ignition stoppage, fuel injection stoppage, etc. and the torque drops to zero.
If the engine speed decreased slowly, there may have been a decrease in torque due to an air fuel ratio that was incorrect (by approximately 20 to 30%), etc.
If the engine speed decreased rapidly, there may have been a malfunction such as when the engine misfires almost continuously due to ignition stoppage, fuel injection stoppage, etc., or when the external load increases due to an external part malfunctioning.
If the air fuel ratio was abnormal, there may have been an intake air leak, sensor malfunction, or fuel supply problem.
If the air fuel ratio was normal, the air volume may have been insufficient or the ignition timing may have been incorrect.
P1603 inspection flow: Narrow down the parts to be inspected according to the vehicle conditions at the time when the malfunction occurred (freeze frame data).
| Vehicle State | Engine Speed | Suspected Area | Primary Parts to Inspect | Procedure | |
|---|---|---|---|---|---|
| Idling or decelerating | Slowly decreases and engine stalls | Air fuel ratio abnormal | Air suction | ·
Intake system connections ·
Purge VSV system ·
Brake booster assembly |
3 to 6 |
| Sensor malfunction (value from sensor too lean) | ·
Mass air flow meter sub-assembly ·
Engine coolant temperature sensor ·
Air fuel ratio sensor system |
7 to 16 | |||
| Sensor malfunction (value from sensor too rich) | 22 to 26,
30 to 34 |
||||
| Fuel supply problem | ·
Fuel pump control system ·
Purge VSV system ·
Fuel line ·
ECM |
17 to 21,
27 to 29 |
|||
| Intake air volume insufficient | ISC flow rate | ·
Throttle with motor body assembly (ISC valve) |
35 to 37 | ||
| Excessive valve overlap | ·
Camshaft timing oil control valve assembly |
38, 39 | |||
| Ignition timing incorrect | Does not operate as expected | ·
Engine coolant temperature sensor ·
Knock control sensor ·
Mass air flow meter sub-assembly |
40 to 42 | ||
| Rapidly decreases and engine stalls | Ignition and injection stops (electrical system malfunction) | Power temporarily cut | ·
Power supply circuit (fuel injector assembly, ignition coil assembly) |
43, 44 | |
| External part malfunctioning | Increase in load | ·
Air conditioning system ·
Electrical load signal system ·
Power steering system ·
A/T system ·
Park/Neutral position switch assembly |
47 to 49 | ||
| Accelerating | - | Crankshaft position sensor, VVT sensor malfunction | Power temporarily cut | ·
Check DTCs |
1 |
| Mass air flow meter sub-assembly | Foreign matter adhesion | ·
Mass air flow meter sub-assembly |
51 | ||
| Fuel supply problem | Fuel leak, clog | ·
Fuel pump control system ·
Fuel line |
54 to 56 | ||
| Ignition and injection stops (electrical system malfunction) | Power temporarily cut | ·
Power supply circuit (fuel injector assembly, ignition coil assembly) |
52, 53 | ||
If the engine speed decreased slowly, there may have been a decrease in torque due to an air fuel ratio that was incorrect (by approximately 20 to 30%), etc.
If the engine speed decreased rapidly, there may have been a malfunction such as when the engine misfires almost continuously due to ignition stoppage, fuel injection stoppage, etc., or when the external load increases due to an external part malfunctioning.
If the air fuel ratio was abnormal, there may have been an intake air leak, sensor malfunction, or fuel supply problem.
If the air fuel ratio was normal, the air volume may have been insufficient or the ignition timing may have been incorrect.
P1605 inspection flow: Narrow down the parts to be inspected according to the vehicle conditions at the time when the malfunction occurred (freeze frame data).
| Engine Speed | Suspected Area | Primary Parts to Inspect | Procedure | |
|---|---|---|---|---|
| Slowly decreases | Air fuel ratio abnormal | Air suction | ·
Intake system connections ·
Purge VSV system ·
Brake booster assembly |
3 to 6 |
| Sensor malfunction (value from sensor too lean) | ·
Mass air flow meter sub-assembly ·
Engine coolant temperature sensor ·
Air fuel ratio sensor system |
7 to 16 | ||
| Sensor malfunction (value from sensor too rich) | 22 to 26,
30 to 34 |
|||
| Fuel supply problem | ·
Fuel pump control system ·
Purge VSV system ·
Fuel line ·
ECM |
17 to 21,
27 to 29 |
||
| Intake air volume insufficient | ISC flow rate | ·
Throttle with motor body assembly (ISC valve) |
35 to 37 | |
| Ignition timing incorrect | Does not operate as expected | ·
Knock control sensor ·
Engine coolant temperature sensor ·
Mass air flow meter sub-assembly |
40 to 42 | |
| Rapidly decreases | Ignition and injection stops (electrical system malfunction) | Power temporarily cut | ·
Power supply circuit (fuel injector assembly, ignition coil assembly) |
43, 44 |
| External part malfunctioning | Increase in load | ·
Air conditioning system ·
Power steering system ·
A/T system ·
Park/Neutral position switch assembly |
47 to 49 | |
Inspect the fuses for circuits related to this system before performing the following procedure.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine / DTC.
Read the DTCs.
Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC P1603 and/or P1605 is output | A |
| DTC P1603 or P1605 and other DTCs are output | B |
A
B
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.
Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA
| Problem Symptom | Freeze Frame Data Item | Suspected Area | Proceed to | ||
|---|---|---|---|---|---|
| Closed Throttle Position SW | Engine Speed | Total of Short FT and Long FT | |||
| When idling or decelerating, engine speed slowly decreases (and engine stalls) | All 5 sets of freeze frame data are ON | Decreases slowly*1 | All 5 sets of freeze frame data are 15% or higher*2 | ·
Air suction ·
Sensor malfunction (value from sensor too lean) ·
Fuel supply problem |
A |
| At least 1 of the 5 sets of freeze frame data is -15% or less*3 | Sensor malfunction (value from sensor too rich) | B | |||
| All 5 sets of freeze frame data are between -15% and 15% | ·
Intake air volume insufficient ·
Ignition timing incorrect |
C | |||
| When idling or decelerating, engine speed rapidly decreases (and engine stalls) | Decreases rapidly*1 | - | ·
Injection stoppage, ignition stoppage ·
Load from external parts |
D | |
| When accelerating or driving at constant speed, engine stalls*4 | At least one is OFF | - | - | ·
Sensor malfunction ·
Injection stoppage, ignition stoppage ·
Fuel supply problem |
E |
*1: A rapid decrease in engine speed may be caused by an electrical fault in the shared wiring of all or a number of cylinders, an increase in load from external parts, etc. The engine speed is considered to have decreased rapidly if either of the following conditions applies.
Otherwise, the engine speed is considered to have decreased slowly.
In the freeze frame data, the decrease in engine speed from #3 to #5 is 400 rpm or higher.
In the freeze frame data, the engine speed at #5 is 120 rpm or less.
If the vehicle speed is 20 km/h (12 mph) or less and the difference between Engine Speed and SPD (NT) is 100 rpm or less, inspect the automatic transaxle. (Depending on the rate of vehicle deceleration, the engine speed may have decreased due to the A/T lock-up release being late.)
*2: When a DTC is stored, feedback compensation increases because the air fuel ratio is determined to be lean.
*3: When a DTC is stored, feedback compensation decreases because the air fuel ratio is determined to be rich.
*4: This item should be checked when DTC P1603 is output and is not necessary to check when only P1605 is output.
A
B
C
D
E
Check for air leaks in the intake system (vacuum hose disconnection, cracks, damaged gaskets, etc.).
Click hereEngine / Hybrid System>2GR-FE INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION
If the accelerator pedal is released after racing the engine, the inspection is easier to perform because the vacuum inside the intake pipes increases and the air suction noise becomes louder.
If Short FT and Long FT are largely different from the normal values when idling (the intake air volume is small) and almost the same as the normal values when racing the engine (the intake air volume is high), air leaks may be present.
There is no air leaks.
Perform "Inspection After Repair" after repairing or replacing the intake system.
Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Fuel Vapor Feed Hose Assembly (to Canister) |
| *2 | Purge VSV Connector |
| *3 | Purge VSV |
Disconnect the fuel vapor feed hose assembly (on the canister side) of the purge VSV.
Start the engine.
Idle the engine.
Disconnect the connector of the purge VSV.
Check if air flows through the purge VSV.
Air does not flow.
When this inspection is performed, the MIL may illuminate. After finishing the inspection, check and clear DTCs.
Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.
Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA
| Freeze Frame Data Item | Result | Suspected Area | Proceed to |
|---|---|---|---|
| Stop Light Switch | At least 1 of the 5 sets of freeze frame data is ON | Air suction from brake booster assembly | A |
| All 5 sets of freeze frame data are OFF | - | B |
A
B
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Start the engine and warm it up until the engine coolant temperature stabilizes.
The A/C switch and all accessory switches should be off.
Idle the engine.
Using the tester, read [Short FT #1 and Short FT #2] of the Data List while depressing the brake pedal.
| Tester Display |
|---|
| Short FT #1 |
| Short FT #2 |
Short FT #1 or Short FT #2 changes by 10% or less.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
Even if the results are normal, the brake booster assembly may have been malfunctioning. Continue this inspection procedure until step 29, and if there are no problems with other parts, replace the brake booster assembly (refer to step 57).
When air leaks from the brake booster assembly is present, the feedback compensation increases because the air fuel ratio becomes lean.
It is also possible to perform the airtightness inspection to check the brake booster assembly.
A
B
C
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.
Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA
| Freeze Frame Data Item | Result | Suspected Area | Proceed to |
|---|---|---|---|
| Calculate Load | Less than 90% of the current value of the vehicle*1 | Mass air flow meter sub-assembly | A |
| AFS Voltage B1S1 or AFS Voltage B2S1 | 3.3 V or higher*2 | ·
Air fuel ratio sensor ·
Wire harness or connector ·
Actual air fuel ratio abnormal |
B |
| Both freeze frame data items listed above | Values are other than above | - | C |
Try to operate the vehicle under the conditions recorded in the freeze frame data which were present when the malfunction occurred. Confirm the data at this time and the data when the engine is idling (engine warmed up, no load, and shift lever in D or N) and compare these data with the freeze frame data.
*1: If the mass air flow meter sub-assembly is malfunctioning, the freeze frame data will show a low engine load value.
*2: If the air fuel ratio sensor is malfunctioning and constantly outputs a value indicating the air fuel ratio is lean, the actual air fuel ratio will become rich and the engine may stall.
A
B
C
Remove the mass air flow meter sub-assembly.
Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>MASS AIR FLOW METER>REMOVAL
Check for foreign matter in the air flow passage of the mass air flow meter sub-assembly.
| Result | Proceed to |
|---|---|
| Visible foreign matter is present | A |
| Visible foreign matter is not present | B |
Even if the results are normal, the mass air flow meter sub-assembly may have been malfunctioning. Continue this inspection procedure until step 29, and if there are no problems with other parts, replace the mass air flow meter sub-assembly (refer to step 57).
Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.
Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
A
B
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the tester on.
Warm up the engine.
Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor / All Data / AFS Voltage B1S1 and AFS Voltage B2S1.
| Active Test Display |
|---|
| Control the Injection Volume for A/F Sensor |
| Data List Display |
|---|
| AFS Voltage B1S1 |
| AFS Voltage B2S1 |
Change the fuel injection volume using the tester, and monitor the voltage output of the air fuel ratio sensors displayed on the tester.
| Tester Display | Specified Condition |
|---|---|
| Control the Injection Volume for A/F Sensor (12.5%) | Air fuel ratio sensors output voltage is below 3.1 V |
| Control the Injection Volume for A/F Sensor (-12.5%) | Air fuel ratio sensors output voltage is higher than 3.4 V |
| Result | Proceed to |
|---|---|
| Abnormal | A |
| Normal | B |
The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.
Even if the results are normal, the air fuel ratio sensor may have been malfunctioning. Continue this inspection procedure until step 29, and if there are no problems with other parts, replace the air fuel ratio sensor (refer to step 57).
A
B
Check the harnesses and connectors, referring to DTC P0031 inspection procedure.
Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P0031
Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
Make sure there is not an excessive amount of force applied to the wire harness.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the harnesses and connectors, referring to DTC P2237 inspection procedure.
Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P2237
Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
Make sure there is not an excessive amount of force applied to the wire harness.
Perform "Inspection After Repair" after replacing the air fuel ratio sensor.
Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.
Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA
| Freeze Frame Data Item | Result | Proceed to |
|---|---|---|
| Initial Engine Coolant Temp, Initial Intake Air Temp | Difference in temperature between each item is below 10°C (18°F)*1 | A |
| Difference in temperature between each item is 10°C (18°F) or higher*2 | B |
*1: A long time had elapsed after stopping the engine.
*2: A long time had not elapsed after stopping the engine.
A
B
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.
Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA
| Freeze Frame Data Item | Result | Suspected Area | Proceed to |
|---|---|---|---|
| Initial Engine Coolant Temp, Coolant Temp, Engine Run Time | Range A | ·
Engine coolant temperature sensor ·
Thermostat |
A |
| Range B | Engine coolant temperature sensor | B | |
| Range C | - | C |
This step is not directly related to engine stall.
A
B
C
Inspect the thermostat.
Click hereEngine / Hybrid System>2GR-FE COOLING>THERMOSTAT>INSPECTION
| Result | Proceed to |
|---|---|
| Abnormal | A |
| Normal | B |
This step is not directly related to engine stall.
A
B
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.
Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA
| Freeze Frame Data Item | Result | Suspected Area | Proceed to |
|---|---|---|---|
| Coolant Temp | 120°C (248°F) or higher | Engine coolant temperature sensor | A |
| Engine coolant temperature is lower than outside temperature* by 15°C (27°F) or higher | Engine coolant temperature sensor | ||
| Freeze frame data item listed above | Values are other than above | - | B |
*: Use an actual outside temperature estimated from the Initial Intake Air, Ambient Temp for A/C, and (if possible) the weather when the DTC was detected.
A
B
Inspect the engine coolant temperature sensor.
Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>ENGINE COOLANT TEMPERATURE SENSOR>INSPECTION
Even if the results are normal, the engine coolant temperature sensor may have been malfunctioning. Continue this inspection procedure until step 29, and if there are no problems with other parts, replace the engine coolant temperature sensor (refer to step 57).
Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.
Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.
Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA
| Freeze Frame Data Item | Result | Suspected Area | Proceed to |
|---|---|---|---|
| EVAP (Purge) VSV | At least 1 of the 5 sets of freeze frame data is not 0% | Purge VSV | A |
| All 5 sets of freeze frame data are 0% | - | B |
If the purge VSV is stuck closed, air fuel ratio compensation by the purge VSV is incorrectly adjusted, and then the air fuel ratio becomes lean and the engine may stall.
A
B
| *1 | Purge VSV |
| *2 | Fuel Vapor Feed Hose Assembly
(to Canister) |
Disconnect the fuel vapor feed hose assembly (on the canister side) of the purge VSV.
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the tester on.
Enter the following menus: Powertrain / Engine / Active Test / Activate the VSV for Evap Control.
| Tester Display |
|---|
| Activate the VSV for Evap Control |
When the purge VSV is operated using the tester, check whether the port of the purge VSV applies suction to your finger.
| Tester Operation | Specified Condition |
|---|---|
| ON | Purge VSV port applies suction to finger |
| OFF | Purge VSV port applies no suction to finger |
| Result | Proceed to |
|---|---|
| Abnormal | A |
| Normal | B |
Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
Even if the results are normal, the purge VSV may have been malfunctioning. Continue this inspection procedure until step 29, and if there are no problems with other parts, replace the purge VSV (refer to step 57).
A
B
Inspect the purge VSV.
Click hereEngine / Hybrid System>2GR-FE EMISSION CONTROL>PURGE VALVE>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the harnesses and connectors, referring to DTC P0443 inspection procedure.
Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P0443
Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
Make sure there is not an excessive amount of force applied to the wire harness.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the harnesses and connectors, referring to DTC P0443 inspection procedure.
Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P0443
Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
Make sure there is not an excessive amount of force applied to the wire harness.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.
Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA
| Freeze Frame Data Item | Result | Suspected Area | Proceed to |
|---|---|---|---|
| Calculate Load | 110% or higher of the current value of the vehicle*1 | Mass air flow meter sub-assembly | A |
| AFS Voltage B1S1 or AFS Voltage B2S1 | Less than 3.3 V*2 | ·
Air fuel ratio sensor ·
Harness and connector ·
Actual air fuel ratio abnormal |
B |
| Both freeze frame data items listed above | Values are other than above | - | C |
Try to operate the vehicle under the conditions recorded in the freeze frame data which were present when the malfunction occurred. Confirm the data at this time and the data when the engine is idling (engine warmed up, no load, and shift lever in D or N) and compare these data with the freeze frame data.
*1: If the mass air flow meter sub-assembly is malfunctioning and incorrectly measures the intake air volume to be higher than the actual volume of air flowing through the intake air surge tank assembly, the freeze frame data will show a high engine load value.
*2: As the air fuel ratio sensor output is low before the sensor warms up, the value at that time cannot be used for diagnosis. If the air fuel ratio sensor is malfunctioning and constantly outputs a value indicating the air fuel ratio is rich, the actual air fuel ratio will become lean and the engine may stall.
A
B
C
Remove the mass air flow meter sub-assembly.
Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>MASS AIR FLOW METER>REMOVAL
Check for foreign matter in the air flow passage of the mass air flow meter sub-assembly.
| Result | Proceed to |
|---|---|
| Visible foreign matter is present | A |
| Visible foreign matter is not present | B |
Even if the results are normal, the mass air flow meter sub-assembly may have been malfunctioning. Continue this inspection procedure until step 34, and if there are no problems with other parts, replace the mass air flow meter sub-assembly (refer to step 57).
Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.
Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
A
B
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the tester on.
Warm up the engine.
Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor / All Data / AFS Voltage B1S1 and AFS Voltage B2S1.
| Active Test Display |
|---|
| Control the Injection Volume for A/F Sensor |
| Data List Display |
|---|
| AFS Voltage B1S1 |
| AFS Voltage B2S1 |
Change the fuel injection volume using the tester, and monitor the voltage output of the air fuel ratio sensors displayed on the tester.
| Tester Display | Specified Condition |
|---|---|
| Control the Injection Volume for A/F Sensor (12.5%) | Air fuel ratio sensors output voltage is below 3.1 V |
| Control the Injection Volume for A/F Sensor (-12.5%) | Air fuel ratio sensors output voltage is higher than 3.4 V |
| Result | Proceed to |
|---|---|
| Abnormal | A |
| Normal | B |
The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.
Even if the results are normal, the air fuel ratio sensor may have been malfunctioning. Continue this inspection procedure until step 34, and if there are no problems with other parts, replace the air fuel ratio sensor (refer to step 57).
A
B
Check the harnesses and connectors, referring to DTC P0031 inspection procedure.
Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P0031
Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
Make sure there is not an excessive amount of force applied to the wire harness.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the harnesses and connectors, referring to DTC P2237 inspection procedure.
Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P2237
Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
Make sure there is not an excessive amount of force applied to the wire harness.
Perform "Inspection After Repair" after replacing the air fuel ratio sensor.
Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump / Speed.
| Tester Display |
|---|
| Control the Fuel Pump / Speed |
When performing the Active Test, check for an operating sound from the fuel pump.
| Control the Fuel Pump / Speed | Specified Condition |
|---|---|
| ON | Operating sound heard |
| OFF | Operating sound not heard |
| Result | Proceed to |
|---|---|
| Abnormal | A |
| Normal | B |
Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
While performing the Active Test, make sure that there is no fuel leakage from the pipes, no signs that fuel has leaked, and no fuel smell.
If the fuel pump operating noise is abnormal, proceed to step 28.
A
B
Inspect the fuel pump.
Click hereEngine / Hybrid System>2GR-FE FUEL>FUEL PUMP>INSPECTION
Perform "Inspection After Repair" after replacing the fuel pump.
Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for foreign matter such as iron particles around the fuel pump, and for signs that the fuel pump was stuck.
| Result | Proceed to |
|---|---|
| There is foreign matter or signs that fuel pump was stuck | A |
| There is no foreign matter and no signs that fuel pump was stuck | B |
If there is foreign matter such as iron particles on the fuel pump, remove the foreign matter.
A
B
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.
Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
| Freeze Frame Data Item | Result | Proceed to |
|---|---|---|
| Initial Engine Coolant Temp, Initial Intake Air Temp | Difference in temperature between each item is below 10°C (18°F)*1 | A |
| Difference in temperature between each item is 10°C (18°F) or higher*2 | B |
*1: A long time had elapsed after stopping the engine.
*2: A long time had not elapsed after stopping the engine.
A
B
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions present when the DTC was stored which are recorded in the freeze frame data.
Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA
| Freeze Frame Data Item | Result | Suspected Area | Proceed to |
|---|---|---|---|
| Initial Engine Coolant Temp, Coolant Temp, Engine Run Time | Range A | ·
Engine coolant temperature sensor ·
Thermostat |
A |
| Range B | Engine coolant temperature sensor | B | |
| Range C | - | C |
This step is not directly related to engine stall.
A
B
C
Inspect the thermostat.
Click hereEngine / Hybrid System>2GR-FE COOLING>THERMOSTAT>INSPECTION
| Result | Proceed to |
|---|---|
| Abnormal | A |
| Normal | B |
This step is not directly related to engine stall.
A
B
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.
Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA
| Freeze Frame Data Item | Result | Suspected Area | Proceed to |
|---|---|---|---|
| Coolant Temp | 120°C (248°F) or higher | Engine coolant temperature sensor | A |
| Engine coolant temperature is lower than outside temperature* by 15°C (27°F) or higher | Engine coolant temperature sensor | ||
| Freeze frame data item listed above | Values are other than above | - | B |
*: Use an actual outside temperature estimated from the Initial Intake Air, Ambient Temp for A/C, and (if possible) the weather when the DTC was detected.
A
B
Inspect the engine coolant temperature sensor.
Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>ENGINE COOLANT TEMPERATURE SENSOR>INSPECTION
| Result | Proceed to |
|---|---|
| Abnormal | A |
| Normal | B |
Even if the results are normal, the engine coolant temperature sensor may have been malfunctioning. If there are no problems with other parts, replace the engine coolant temperature sensor (refer to step 57).
Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.
Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
A
B
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.
Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA
| Freeze Frame Data Item | Result | Suspected Area | Proceed to |
|---|---|---|---|
| Total of ISC Learning Value and ISC Feedback Value | Less than 80% of the current value of the vehicle*1 | Throttle with motor body assembly | A |
| 120% or higher of the current value of the vehicle*2 | B | ||
| From 80 to 120% of the current value of the vehicle | - | C |
Try to operate the vehicle under the conditions recorded in the freeze frame data which were present when the malfunction occurred. Confirm the data at this time and the data when the engine is idling (engine warmed up, no load, and shift lever in D or N) and compare these data with the freeze frame data.
*1: If the throttle with motor body assembly has a temporary problem in which it cannot fully close, the intake air volume and engine speed increase. As a result, the ISC learning amount becomes less than the standard. At this time, if the throttle with motor body assembly returns to normal and fully closes, the intake air volume will be insufficient and the engine may stall.
*2: If carbon accumulates on the throttle with motor body assembly and the intake air volume decreases, the ISC learning amount is increased to maintain the idle speed. If this situation continues, the ISC learning amount reaches the upper limit, the idle speed cannot be maintained causing idling to become unstable, and the engine may stall.
A
B
C
Check for foreign matter and signs that the throttle with motor body assembly was stuck, and also check that the valve and shaft move smoothly during operation.
| Result | Proceed to |
|---|---|
| Abnormal | A |
| Normal | B |
Even if the results are normal, the throttle with motor body assembly may have been malfunctioning. Continue this inspection procedure until step 42, and if there are no problems with other parts, replace the throttle with motor body assembly (refer to step 57).
Perform "Inspection After Repair" after replacing the throttle with motor body assembly.
Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
A
B
Check if carbon is in the air flow passage of the throttle with motor body assembly.
| Result | Proceed to |
|---|---|
| Carbon in passage | A |
| No carbon in passage | B |
Even if the results are normal, the throttle with motor body assembly may have been malfunctioning. Continue this inspection procedure until step 42, and if there are no problems with other parts, replace the throttle with motor body assembly (refer to step 57).
Perform "Inspection After Repair" after replacing the throttle with motor body assembly.
Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
A
B
Perform the Active Test, referring to DTC P0011 inspection procedure.
Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P0011
Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
When the results of the inspection using the Active Test are normal but the valve operating noise is abnormal, check the valve for any signs of problems.
If the camshaft timing oil control valve assembly (for intake camshaft) is stuck at the advanced side, the valve overlap increases and combustion worsens due to the internal EGR which may cause rough idle or cause the engine to stall.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Perform the Active Test, referring to DTC P0014 inspection procedure.
Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P0014
Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
When the results of the inspection using the Active Test are normal but the valve operating noise is abnormal, check the valve for any signs of problems.
If the camshaft timing oil control valve assembly (for exhaust camshaft) is stuck at the retard side, the valve overlap increases and combustion worsens due to the internal EGR which may cause rough idle or cause the engine to stall.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.
Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
| Freeze Frame Data Item | Suspected Area | Proceed to | |
|---|---|---|---|
| IGN Advance | Knock Correct Learn Value | ||
| Differs from the current value of the vehicle by 10 deg or more | Below 3°CA | ·
Engine coolant temperature sensor ·
Mass air flow meter sub-assembly ·
Knock control sensor |
A |
| 3°CA or more | - | B | |
| Differs from the current value of the vehicle by less than 10 deg | - | ||
Try to operate the vehicle under the conditions recorded in the freeze frame data which were present when the malfunction occurred. Confirm the data at this time and the data when the engine is idling (engine warmed up, no load, and shift lever in D or N) and compare these data with the freeze frame data.
Even if the results are normal, the knock control sensors may have been malfunctioning. If there are no problems with other parts, replace the knock control sensors (refer to step 57).
A
B
Inspect the engine coolant temperature sensor.
Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>ENGINE COOLANT TEMPERATURE SENSOR>INSPECTION
Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.
Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the mass air flow meter sub-assembly (intake air temperature sensor).
Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>MASS AIR FLOW METER>INSPECTION
Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly or knock control sensor.
Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the harnesses and connectors, referring to DTC P0300 inspection procedure.
Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P0300
Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
Make sure there is not an excessive amount of force applied to the wire harness.
A rapid decrease in engine speed may have been caused by a malfunction in all or multiple cylinders. (There may be an electrical malfunction in the wiring shared by all the cylinders.)
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the harnesses and connectors, referring to DTC P0351 inspection procedure.
Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P0351
Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
Make sure there is not an excessive amount of force applied to the wire harness.
A rapid decrease in engine speed may have been caused by a malfunction in all or multiple cylinders. (There may be an electrical malfunction in the wiring shared by all the cylinders.)
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.
Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA
| Freeze Frame Data Item | Result | Suspected Area | Proceed to |
|---|---|---|---|
| Idle Spark Advn Ctrl (#1 to #6) | At least one cylinder shows a value of 4°CA or higher | ·
Fuel injector system ·
Ignition coil system |
A |
| All cylinders show a value of less than 4°CA | - | B |
A
B
Change the location of the ignition coil assembly for the cylinder whose Idle Spark Advn Ctrl (#1 to #6) was 4°CA or more in step 45.
Connect the intelligent tester to the DLC3.
Start the engine.
Using the tester, select [Idle Spark Advn Ctrl (#1 to #6)] of the Data List.
| Tester Display |
|---|
| Idle Spark Advn Ctrl #1 |
| Idle Spark Advn Ctrl #2 |
| Idle Spark Advn Ctrl #3 |
| Idle Spark Advn Ctrl #4 |
| Idle Spark Advn Ctrl #5 |
| Idle Spark Advn Ctrl #6 |
| Result | Proceed to |
|---|---|
| Same as result in step 45 | A |
| Different from result in step 45 | B |
Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
Perform "Inspection After Repair" after replacing the ignition coil assembly.
Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
A
B
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.
Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA
| Freeze Frame Data Item | Suspected Area | Proceed to | ||
|---|---|---|---|---|
| A/C Signal | Air Conditioner FB Val | Power Steering Signal | ||
| A/C Signal display changes from OFF to ON | Value displayed for Air Conditioner FB Val increases | Does not change from OFF | A/C system | B |
| Changes from OFF to ON | Power steering system | A | ||
| A/C Signal display does not change from OFF | Value displayed for Air Conditioner FB Val does not increase | Changes from OFF to ON | ||
| Does not change from OFF | - | |||
Try to operate the vehicle under the conditions recorded in the freeze frame data which were present when the malfunction occurred. Confirm the data at this time and the data when the engine is idling (engine warmed up, no load, and shift lever in D or N) and compare these data with the freeze frame data.
The normal value for the ISC learning amount is engine displacement (liters) x 0.9.
Even if the results are normal, the power steering system or the air conditioning system may have been malfunctioning. Continue this inspection procedure until step 49, and if there are no problems with other parts, inspect the power steering system and the air conditioning system (refer to step 57).
A
B
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.
Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA
| Freeze Frame Data Item | Suspected Area | Proceed to | |||
|---|---|---|---|---|---|
| Electrical Load Signal 1 | Electric Load Feedback Val | Difference between Engine Speed and SPD (NT) | Vehicle Speed | ||
| Electrical Load Signal 1 display changes from OFF to ON*1, or value displayed for Electric Load Feedback Val increases*1 | Value displayed for Electric Load Feedback Val changes | - | - | Electrical load signal circuit | A |
| Value displayed for Electric Load Feedback Val does not change | At least 1 of the 5 sets of freeze frame data is less than 100 rpm | Less than 20 km/h (12 mph) | A/T system | B | |
| Electrical Load Signal 1 display does not change from OFF, or value displayed for Electric Load Feedback Val does not increase | - | At least 1 of the 5 sets of freeze frame data is less than 100 rpm | Less than 20 km/h (12 mph) | ||
| At least 1 of the 5 sets of freeze frame data is less than 100 rpm | 20 km/h (12 mph) or higher | - | C | ||
| All 5 sets of freeze frame data are 100 rpm or higher | - | ||||
| Electrical Load Signal 1 display changes from OFF to ON*1, or value displayed for Electric Load Feedback Val increases*1 | Value displayed for Electric Load Feedback Val does not change | At least 1 of the 5 sets of freeze frame data is less than 100 rpm | 20 km/h (12 mph) or higher | ||
| All 5 sets of freeze frame data are 100 rpm or higher | - | ||||
*1: If the Electrical Load Signal 1 display changes from OFF to ON or the Electric Load Feedback Val increases, it probably is a malfunction due to a change in electrical load. Check the generator and the continuity and connections between the generator and ECM.
If the vehicle speed is 20 km/h (12 mph) or less and the difference between Engine Speed and SPD (NT) is 100 rpm or less, inspect the automatic transaxle. (Depending on the rate of vehicle deceleration, the engine speed may have decreased due to the A/T lock-up release being late.)
The normal value for the ISC learning amount is engine displacement (liters) x 0.9.
Even if the results are normal, the electrical load signal system and/or the A/T system may have been malfunctioning. Continue this inspection procedure until step 49, and if there are no problems with other parts, inspect the electrical load system and/or the A/T system (refer to step 57).
A
B
C
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.
Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA
| Freeze Frame Data Item | Suspected Area | Proceed to | |
|---|---|---|---|
| Shift SW Status (P or N Range) | Neutral Position SW Signal | ||
| P and N position are both OFF in at least one data set | ON when Shift SW Status D or R | Park/Neutral position switch assembly | A |
| OFF when Shift SW Status D or R | A/T system | B | |
| All 5 sets of freeze frame data are ON | - | - | C |
Even if the results are normal, the park/neutral position switch assembly and/or A/T system may have been malfunctioning. If there are no problems with other parts, inspect the park/neutral position switch assembly and/or A/T system (refer to step 57).
A
Click hereDrivetrain>U660E AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>INSPECTION
B
C
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.
Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA
| Freeze Frame Data Item | Result | Suspected Area | Proceed to |
|---|---|---|---|
| Throttle Sensor Position, Calculate Load | Calculate Load decreases while Throttle Sensor Position increases | Mass air flow meter sub-assembly | A |
| Calculate Load does not decrease while Throttle Sensor Position increases | - | B |
A
B
Remove the mass air flow meter sub-assembly.
Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>MASS AIR FLOW METER>REMOVAL
Check for foreign matter in the air flow passage of the mass air flow meter sub-assembly.
| Result | Proceed to |
|---|---|
| Visible foreign matter is present | A |
| Visible foreign matter is not present | B |
Even if the results are normal, the mass air flow meter sub-assembly may have been malfunctioning. Continue this inspection procedure until step 56, and if there are no problems with other parts, replace the mass air flow meter sub-assembly (refer to step 57).
Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.
Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
A
B
Check the harnesses and connectors, referring to DTC P0300 inspection procedure.
Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P0300
Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
Make sure there is not an excessive amount of force applied to the wire harness.
A rapid decrease in engine speed may have been caused by a malfunction in all or multiple cylinders. (There may be an electrical malfunction in the wiring shared by all the cylinders.)
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the harnesses and connectors, referring to DTC P0351 inspection procedure.
Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P0351
Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
Make sure there is not an excessive amount of force applied to the wire harness.
A rapid decrease in engine speed may have been caused by a malfunction in all or multiple cylinders. (There may be an electrical malfunction in the wiring shared by all the cylinders.)
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump / Speed.
| Tester Display |
|---|
| Control the Fuel Pump / Speed |
When performing the Active Test, check for an operating sound from the fuel pump.
| Control the Fuel Pump / Speed | Specified Condition |
|---|---|
| ON | Operating sound heard |
| OFF | Operating sound not heard |
| Result | Proceed to |
|---|---|
| Abnormal | A |
| Normal | B |
Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
While performing the Active Test, make sure that there is no fuel leakage from the pipes, no signs that fuel has leaked, and no fuel smell.
If the fuel pump operating noise is abnormal, proceed to step 56
A
B
Inspect the fuel pump.
Click hereEngine / Hybrid System>2GR-FE FUEL>FUEL PUMP>INSPECTION
Perform "Inspection After Repair" after replacing the fuel pump.
Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for foreign matter such as iron particles around the fuel pump, and for signs that the fuel pump was stuck.
| Result | Proceed to |
|---|---|
| There is foreign matter or signs that fuel pump was stuck | A |
| There is no foreign matter and no signs that fuel pump was stuck | B |
If there is foreign matter such as iron particles on the fuel pump, remove the foreign matter.
A
B
If the malfunction could not be identified in steps 3 to 29, replace the part which is suspected to be malfunctioning according to the step where an inspection was performed.
| Performed Step | Inspection or Part to Replace |
|---|---|
| Step 6 | Brake booster assembly replacement |
| Step 8 | Mass air flow meter sub-assembly replacement |
| Step 9 | Air fuel ratio sensor replacement |
| Step 16 | Engine coolant temperature sensor replacement |
| Step 18 | Purge VSV replacement |
| Step 29 | Fuel pump replacement |
If the malfunction could not be identified in steps 22 to 26, 30 to 34 replace the part which is suspected to be malfunctioning according to the step where an inspection was performed.
| Performed Step | Inspection or Part to Replace |
|---|---|
| Step 23 | Mass air flow meter sub-assembly replacement |
| Step 24 | Air fuel ratio sensor replacement |
| Step 34 | Engine coolant temperature sensor replacement |
If the malfunction could not be identified in steps 35 to 42, replace the part which is suspected to be malfunctioning according to the step where an inspection was performed.
| Performed Step | Inspection or Part to Replace |
|---|---|
| Step 36, 37 | Throttle with motor body assembly replacement |
| Step 40 | Knock control sensor replacement |
If the malfunction could not be identified in steps 43 to 49, inspect and repair the part which is suspected to be malfunctioning according to the step where an inspection was performed.
| Performed Step | Inspection or Part to Replace |
|---|---|
| Step 47 | A/C system inspection and repair
Power steering system inspection and repair |
| Step 48 | Electrical load system inspection and repair
A/T system inspection and repair |
| Step 49 | Park/Neutral position switch assembly inspection and repair
A/T system inspection and repair |
If the malfunction could not be identified in steps 50 to 56, replace the part which is suspected to be malfunctioning according to the step where an inspection was performed.
| Performed Step | Inspection or Part to Replace |
|---|---|
| Step 51 | Mass air flow meter sub-assembly replacement |
Referring to the chart, inspect and repair or replace the part from the step where an inspection was performed.
Perform "Inspection After Repair" after replacing or servicing parts related to engine operation. Refer to detailed information in Initialization.
Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Clear the DTCs.
Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| NEXT |
NEXT
Check if engine stall symptoms are present.
If any engine stall symptoms are present, recheck for DTCs and freeze frame data and perform an inspection.
| Proceed to |
|---|
| OK |
| NG |
OK
NG