Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM J

N04C-WA ENGINE CONTROL  ECD SYSTEM  Engine Difficult to Start or Stalling  


CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

After replacing the injection or supply pump assembly, the ECM needs initialization (Click here Engine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

After replacing the injector assembly, the ECM needs registration (Click here Engine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).



HINT:
·

Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List values may occur depending on the measuring conditions or the vehicle's age. Do not assume the vehicle is normal when the Data List outputs standard values. There may be concealed factors of the malfunction.

·

If the vehicle runs out of fuel while the engine is operating, there is a chance that the engine may be difficult to restart after fuel is refilled.



PROCEDURE

1.CHECK DTC OUTPUT (RELATED TO ENGINE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.


d.

Read the DTCs.


Result:
Result Proceed to
No output A
DTCs related to engine B



A

2.CHECK FUEL FILTER ASSEMBLY

B

2.CHECK FUEL FILTER ASSEMBLY
a.

Check that the fuel filter is not clogged.

OK:

Fuel filter is not clogged.



Result:
Proceed to
OK
NG



OK

3.CHECK ENGINE CRANKING CONDITION

NG

3.CHECK ENGINE CRANKING CONDITION
a.

Check the engine cranking condition.


b.

Compare the cranking condition with that of a normal engine of the same model, and carefully check if there is any difference between them.

OK:

Engine cranking condition is normal.



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (COMMON RAIL PRESSURE)

NG

CHECK AND REPLACE BATTERY, CHARGING SYSTEM, STARTER ASSEMBLY AND STARTING SYSTEM

4.READ VALUE USING GTS (COMMON RAIL PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Common Rail Pressure.


e.

Read the value.

Standard:
Item Inspection Condition Reference Value
Common Rail Pressure Cranking, and engine coolant temperature 0°C (32°F) or more 15 MPa or more



Result:
Proceed to
OK
NG



OK

5.CHECK IF INITIAL COMBUSTION OCCURS

NG

5.CHECK IF INITIAL COMBUSTION OCCURS
a.

Check if initial combustion occurs.


Result:
Result Proceed to
No initial combustion A
Initial combustion occurs B



A

6.READ VALUE USING GTS (COMMON RAIL PRESSURE)

B

7.CHECK AIR INTAKE SYSTEM AND EXHAUST SYSTEM
6.READ VALUE USING GTS (COMMON RAIL PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Common Rail Pressure.


e.

Check that the internal fuel pressure of the common rail is within the specification below.

Standard:
Engine Speed Engine Speed
Idling Approximately 25 to 35 MPa



Result:
Proceed to
OK
NG



OK

7.CHECK AIR INTAKE SYSTEM AND EXHAUST SYSTEM

NG

13.CHECK IF FUEL IS BEING SUPPLIED TO INJECTION OR SUPPLY PUMP ASSEMBLY
7.CHECK AIR INTAKE SYSTEM AND EXHAUST SYSTEM
a.

Inspect the engine condition.


Result:
Proceed to
OK
NG



OK

8.INSPECT EXHAUST RETARDER ASSEMBLY

NG

REPAIR OR REPLACE LOCATIONS WHERE MALFUNCTIONS EXIST

8.INSPECT EXHAUST RETARDER ASSEMBLY
a.

Inspect the exhaust retarder assembly.

Click hereBrake>EXHAUST BRAKE>EXHAUST BRAKE RETARDER>INSPECTION


Result:
Proceed to
OK
NG



OK

9.READ VALUE USING GTS (COMMON RAIL PRESSURE AND INJECTION VOLUME)

NG

REPLACE EXHAUST RETARDER ASSEMBLY

9.READ VALUE USING GTS (COMMON RAIL PRESSURE AND INJECTION VOLUME)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List.


e.

Enter the following menus in order and read the values.

·

Common Rail Pressure

·

Injection Volume


Standard:
Item Engine Speed* Reference Value
Common Rail Pressure Idling 25 to 35 MPa
Injection Volume Idling 5 to 16 mm3/st


HINT:

*: The shift lever should be in the neutral position, and the A/C switch and all accessory switches should be OFF.



Result:
Proceed to
OK
NG



OK

10.CHECK CYLINDER COMPRESSION PRESSURE

NG

14.INSPECT ECM (THW TERMINAL VOLTAGE)
10.CHECK CYLINDER COMPRESSION PRESSURE
a.

Check the cylinder compression pressure.

Click hereEngine / Hybrid System>N04C-WA (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY - ECM)

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

11.CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY - ECM)
a.
A405886C09
1.51,0.125 1.885,0.406 0.375,0.281 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a 1.667,0.208 1.979,0.406 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


Disconnect the injector assembly connectors.


b.

Disconnect the ECM connectors.


c.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
i5-1 - E-15 Always Below 1 Ω
i5-2 - E-14 Always Below 1 Ω
i8-1 - E-16 Always Below 1 Ω
i8-2 - E-34 Always Below 1 Ω
i6-1 - E-20 Always Below 1 Ω
i6-2 - E-38 Always Below 1 Ω
i7-1 - E-19 Always Below 1 Ω
i7-2 - E-18 Always Below 1 Ω
i5-1 or E-15 - Body ground Always 10 kΩ or higher
i5-2 or E-14 - Body ground Always 10 kΩ or higher
i8-1 or E-16 - Body ground Always 10 kΩ or higher
i8-2 or E-34 - Body ground Always 10 kΩ or higher
i6-1 or E-20 - Body ground Always 10 kΩ or higher
i6-2 or E-38 - Body ground Always 10 kΩ or higher
i7-1 or E-19 - Body ground Always 10 kΩ or higher
i7-2 or E-18 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

12.PERFORM ACTIVE TEST USING GTS (CONTROL THE CYLINDER FUEL CUT #1 TO #4)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.PERFORM ACTIVE TEST USING GTS (CONTROL THE CYLINDER FUEL CUT #1 TO #4)
HINT:

Use this Active Test to determine the malfunctioning cylinder.


a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Active Test / Control the Cylinder Fuel Cut #1 to #4.

HINT:
·

If the engine idle speed does not change when a fuel injector is disabled, the cylinder being tested is malfunctioning.

·

If the cylinder being tested is normal, there will be a significant change in idle speed when the fuel injection is stopped for that cylinder.




Result:
Result Proceed to
Engine idling condition becomes unstable A
Engine idling condition does not change B



A

B

13.CHECK IF FUEL IS BEING SUPPLIED TO INJECTION OR SUPPLY PUMP ASSEMBLY
a.

Disconnect the inlet hose from the injection or supply pump assembly.


b.

Operate the priming pump and check that fuel is being supplied to the injection or supply pump assembly.

OK:

Fuel is properly supplied to the injection or supply pump assembly when the priming pump is operated.



Result:
Proceed to
OK
NG



OK

NG

CHECK AND REPLACE FUEL PIPE CLOGGING (INCLUDING FUEL FREEZING) (FUEL TANK - SUPPLY PUMP ASSEMBLY)

14.INSPECT ECM (THW TERMINAL VOLTAGE)
a.
A405886C09
1.51,0.125 1.885,0.406 0.375,0.281 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a 1.667,0.208 1.979,0.406 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


A405887C05
1.521,0.167 1.885,0.448 0.365,0.281 0.104,0.115 0.417,0.313 0.313,0.198 10 false *a 1.667,0.25 1.865,0.427 0.198,0.177 10 false M
*a Signal Check Harness Lead Connector


Connect the ECM connector.


b.

Connect the water temperature sender gage assembly connector.


c.

Connect the signal check harness to the ECM and ECM vehicle side harness.


d.

Start the engine.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E-66 - M-54 Idling, engine coolant temperature between 80 and 120°C (176 and 248°F) 0.2 to 1.0 V


Text in Illustration
*a Component with harness connected
(ECM)


Result:
Proceed to
OK
NG



OK

15.INSPECT CRANKSHAFT POSITION SENSOR

NG

18.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
15.INSPECT CRANKSHAFT POSITION SENSOR
a.
A405887C14
1.5,0.083 1.948,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.667,0.156 1.979,0.354 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


Disconnect the ECM connector.


b.

Connect the signal check harness to the ECM and ECM vehicle side harness.


c.

Start the engine.


d.

While idling the engine, check the waveform between the specified terminals of the ECM connector using an oscilloscope.

A407889E03
0.479,1.063 0.938,1.26 0.458,0.198 10 false G 0.406,1.75 1.396,2.198 0.99,0.448 10 false NE 3.167,2.469 4.219,2.688 1.052,0.219 10 false 20 ms/DIV. 3.458,0.052 4.51,0.271 1.052,0.219 10 false 720° 6.427,0.135 7.021,0.427 0.594,0.292 10 false 5 V/DIV. 6.625,1.135 7.156,1.438 0.531,0.302 10 false GND 6.625,1.771 7.156,2.073 0.531,0.302 10 false GND

Standard:
Tester Connection Condition Specified Condition
E-52 - E-72 Engine idling Correct waveform appears as shown
E-73 - E-53 Engine idling Correct waveform appears as shown



Result:
Proceed to
OK
NG



OK

16.CHECK HARNESS AND CONNECTOR (ST RELAY - ECM)

NG

19.INSPECT CRANKSHAFT POSITION SENSOR
16.CHECK HARNESS AND CONNECTOR (ST RELAY - ECM)
a.

Disconnect the ECM connector.


b.

Remove the ST relay.


c.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


d.
A405886C10
1.479,0.125 1.896,0.396 0.417,0.271 0.177,0.167 0.49,0.365 0.313,0.198 10 false *a 1.635,0.188 1.948,0.385 0.313,0.198 10 false V
*a Signal Check Harness Lead Connector


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST relay terminal 1 - V-12 Always Below 1 Ω
ST relay terminal 1 or V-12 - Body ground Always 10 kΩ or higher



e.

Reinstall the ST relay.


f.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

17.INSPECT ECM (PCR1 AND PCR2 TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.INSPECT ECM (PCR1 AND PCR2 TERMINAL VOLTAGE)
a.

Disconnect the ECM connector.


b.

Connect the signal check harness to the ECM and ECM vehicle side harness.


c.

Start the engine.


d.
A405887C14
1.5,0.083 1.948,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.667,0.156 1.979,0.354 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E-49 - E-56 Idling 1.3 to 1.7 V
E-68 - E-56 Idling 1.3 to 1.7 V



Result:
Proceed to
OK
NG



OK

NG

20.INSPECT COMMON RAIL ASSEMBLY (FUEL PRESSURE SENSOR)
18.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
a.
A126612C04
1.573,2.844 1.313,3.198 1.313,3.198 1.313,3.333 false 0.635,1.688 0.813,1.833 0.177,0.146 10 false 30 0.635,1.875 0.813,2.021 0.177,0.146 10 false 20 0.635,2.177 0.813,2.323 0.177,0.146 10 false 10 0.729,2.49 0.823,2.635 0.094,0.146 10 false 5 0.729,3.146 0.823,3.292 0.094,0.146 10 false 1 2.417,2.948 2.604,3.115 0.188,0.167 10 false *1 1.198,3.375 1.396,3.542 0.198,0.167 10 false *a 0.729,2.906 0.823,3.052 0.094,0.146 10 false 2 0.729,2.708 0.823,2.854 0.094,0.146 10 false 3 0.583,3.604 0.802,3.75 0.219,0.146 10 false 0.3 0.583,3.417 0.802,3.563 0.219,0.146 10 false 0.5 0.583,3.948 0.802,4.094 0.219,0.146 10 false 0.1 0.583,3.76 0.802,3.906 0.219,0.146 10 false 0.2 0.885,4.021 1.104,4.167 0.219,0.146 10 false -20 1.281,4.021 1.375,4.177 0.094,0.156 10 false 0 1.542,4.021 1.719,4.167 0.177,0.146 10 false 20 1.885,4.021 2.063,4.167 0.177,0.146 10 false 40 2.219,4.021 2.396,4.167 0.177,0.146 10 false 80 2.594,4.021 2.896,4.167 0.302,0.146 10 false 100 0.875,4.188 1.115,4.365 0.24,0.177 10 false (-4) 1.167,4.188 1.438,4.365 0.271,0.177 10 false (32) 1.479,4.188 1.75,4.365 0.271,0.177 10 false (68) 1.781,4.188 2.125,4.365 0.344,0.177 10 false (104) 2.188,4.188 2.531,4.365 0.344,0.177 10 false (176) 2.594,4.188 2.938,4.365 0.344,0.177 10 false (212) 0.875,1.573 1.073,1.729 0.198,0.156 10 false kΩ 0.302,4.031 0.51,4.198 0.208,0.167 10 false °C 0.24,4.229 0.531,4.396 0.292,0.167 10 false (°F)
*1 Engine Coolant Temperature Sensor
*a Acceptable


Remove the engine coolant temperature sensor.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 2.32 to 2.59 kΩ
80°C (176°F) 0.31 to 0.326 kΩ


NOTICE:

When checking the sensor in water, keep the terminals dry. After the check, wipe the sensor dry.


HINT:

Alternative procedure: Connect an ohmmeter to the installed ECT sensor and read the resistance. Use an infrared thermometer to measure the engine temperature in the immediate vicinity of the sensor. Compare these values against the resistance/ temperature graph. Change the engine temperature (warm up or cool down) and repeat the test.



c.

Reinstall the engine coolant temperature sensor.


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - ENGINE COOLANT TEMPERATURE SENSOR)

NG

19.INSPECT CRANKSHAFT POSITION SENSOR

Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - CRANKSHAFT POSITION SENSOR)

NG

20.INSPECT COMMON RAIL ASSEMBLY (FUEL PRESSURE SENSOR)
a.

Inspect the fuel pressure sensor.

Click hereEngine / Hybrid System>N04C-WA (FUEL)>COMMON RAIL>INSPECTION


Result:
Proceed to
OK
NG



OK

21.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)

NG

REPLACE COMMON RAIL ASSEMBLY

21.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)
a.

Disconnect the ECM connector.


b.

Disconnect the fuel pressure sensor connector.


c.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B140-1 (VC1) - E-13 Always Below 1 Ω
B140-2 (PCR1) - E-49 Always Below 1 Ω
B140-2 (PCR1) - E-68 Always Below 1 Ω
B140-3 (E2) - E-56 Always Below 1 Ω
B140-2 (PCR1) or E-49 - Body ground Always 10 kΩ or higher
B140-1 (VC) or E13 - Body ground Always 10 kΩ or higher
B140-2 (PCR1) or E-68 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

22.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

22.REPLACE ECM
a.

Replace the ECM (Click here Engine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECM>REMOVAL).

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).



b.

Check if the engine starts smoothly or if the engine stalls.

OK:

The engine starts smoothly and does not stall.



Result:
Proceed to
OK
NG



OK

END

NG