When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.
| Replaced Parts (A) | Pipes Requiring New Replacement |
|---|---|
| Injector assembly (including shuffling the injector assemblies between the cylinders) | ·
No. 1 injection pipe sub-assembly ·
No. 2 injection pipe sub-assembly |
| Supply pump assembly | Fuel inlet pipe sub-assembly |
·
Common rail assembly ·
Cylinder block sub-assembly ·
Cylinder head sub-assembly ·
Cylinder head gasket ·
Timing chain case assembly |
·
No. 1 injection pipe sub-assembly ·
No. 2 injection pipe sub-assembly ·
Fuel inlet pipe sub-assembly |
After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.
The injector assembly is a precision instrument. Do not use the injector assembly if it is struck or dropped.
The supply pump assembly is a precision instrument. Do not use the supply pump assembly if it is struck or dropped.
The common rail assembly is a precision instrument. Do not use the common rail assembly if it is struck or dropped.
Hold the supply pump assembly itself during removal and installation. Do not hold the pre-stroke control valve or fuel pipe, etc.
Hold the common rail assembly itself during removal and installation. Do not hold the pressure discharge valve or fuel pressure sensor, etc.
Make sure foreign matter does not enter the fuel path.
11310
1.INSTALL TIMING CHAIN CASE ASSEMBLY AND ENGINE WATER PUMP ASSEMBLY
Install a new gasket to the timing chain case assembly.
Install the 4 new O-rings to the cylinder block sub-assembly and cylinder head sub-assembly.
Clean and degrease the contact surfaces of the timing chain case assembly, cylinder head sub-assembly and cylinder block sub-assembly.
Apply a coating of seal packing to the timing chain case assembly at the points shown in the illustration.
| *a | 46 mm (1.81 in.) | *b | 50 mm (1.97 in.) |
| *c | 2.0 to 3.0 mm (0.0787 to 0.118 in.) | *d | 2.5 to 3.5 mm (0.0984 to 0.138 in.) |
| *e | 3.0 to 4.0 mm (0.118 to 0.158 in.) | *f | 1.5 to 2.5 mm (0.0591 to 0.0984 in.) |
| *g | 13 to 15 mm (0.512 to 0.591 in.) | *h | 9.0 to 11 mm (0.354 to 0.433 in.) |
| *i | 31 to 33 mm (1.22 to 1.30 in.) | - | - |
Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent.
| Line Type and Area | Seal Packing Diameter | Application Area | Seal Packing Application Length |
|---|---|---|---|
| Dashed Line | 1.5 to 2.5 mm (0.0591 to 0.0984 in.) | 2.0 to 3.0 mm (0.0787 to 0.118 in.) | - |
| A - A | 2.5 to 3.5 mm (0.0984 to 0.138 in.) | 2.0 to 3.0 mm (0.0787 to 0.118 in.) | 46 mm (1.81 in.) |
| B - B | 2.5 to 3.5 mm (0.0984 to 0.138 in.) | 2.0 to 3.0 mm (0.0787 to 0.118 in.) | 50 mm (1.97 in.) |
| D | 1.5 to 2.5 mm (0.0591 to 0.0984 in.) | 3.0 to 4.0 mm (0.118 to 0.158 in.) | - |
Using non-residue solvent, clean and remove any oil from the installation surface.
Install the part within 3 minutes and tighten the bolts within 10 minutes after applying seal packing.
Do not add engine oil for at least 2 hours after installation.
Do not start the engine within 2 hours after installation.
Temporarily install the timing chain case assembly with the 15 bolts.
| *a | Type of bolt | *b | Tightening |
| Item | Length | Thread Diameter |
|---|---|---|
| Bolt A | 30 mm (1.18 in.) | 8.0 mm (0.315 in.) |
| Bolt B | 45 mm (1.77 in.) | 8.0 mm (0.315 in.) |
| Bolt C | 65 mm (2.56 in.) | 8.0 mm (0.315 in.) |
| Bolt D | 30 mm (1.18 in.) | 10 mm (0.394 in.) |
Temporarily install a new gasket and the engine water pump assembly with the 8 bolts.
Tighten the 23 bolts in the order shown in the illustration.
Check the torque of bolt 1 after tightening bolt 23.
22815A
2.INSTALL INJECTION PUMP INSULATOR
22100
3.INSTALL SUPPLY PUMP ASSEMBLY
13559
4.INSTALL NO. 1 CHAIN TENSIONER SLIPPER
13561
5.TEMPORARILY INSTALL NO. 1 CHAIN VIBRATION DAMPER
13506
6.INSTALL CRANKSHAFT TIMING SPROCKET, INJECTION PUMP DRIVE GEAR WITH NO. 1 CHAIN SUB-ASSEMBLY
13561
7.TIGHTEN NO. 1 CHAIN VIBRATION DAMPER
13540
8.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY
9.INSTALL SUPPLY PUMP SHAFT NUT
13523
10.INSTALL CAMSHAFT TIMING SPROCKET
13562
11.INSTALL NO. 2 CHAIN VIBRATION DAMPER
13507
12.INSTALL NO. 2 CHAIN SUB-ASSEMBLY
13559
13.INSTALL NO. 2 CHAIN TENSIONER SLIPPER
13550
14.INSTALL NO. 2 CHAIN TENSIONER ASSEMBLY
13566B
15.INSTALL TIMING CHAIN GUIDE
16.CHECK NO. 1 CYLINDER TO TDC/COMPRESSION
17.INSTALL BALANCESHAFT TIMING SPROCKET, BALANCESHAFT GEAR SUB-ASSEMBLY WITH NO. 3 CHAIN SUB-ASSEMBLY
11991A
18.INSTALL NO. 1 BALANCESHAFT THRUST PLATE
13560A
19.INSTALL NO. 3 CHAIN TENSIONER ASSEMBLY
13519
20.INSTALL OIL PUMP DRIVE GEAR
Install the oil pump drive gear to the crankshaft.
11324
21.INSTALL TIMING CHAIN COVER PLATE
11302
22.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY
Apply a light coat of engine oil to a new timing chain case gasket.
Install the timing chain case gasket to the timing chain case assembly.
Clean and degrease the contact surfaces of the timing chain cover sub-assembly and timing chain case assembly.
Apply a coating of seal packing to the timing chain cover sub-assembly at the points shown in the illustration.
| *a | 2.0 to 3.0 mm (0.0787 to 0.118 in.) | *b | 2.5 to 3.5 mm (0.0984 to 0.138 in.) |
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent.
2.5 to 3.5 mm (0.0984 to 0.138 in.)
Using non-residue solvent, clean and remove any oil from the installation surface.
Install the part within 3 minutes and tighten the bolts within 10 minutes after applying seal packing.
Do not add engine oil for at least 2 hours after installation.
Do not start the engine within 2 hours after installation.
Temporarily install the timing chain cover sub-assembly with the 20 bolts.
| *a | Type of bolt | *b | Tightening |
| Item | Length | Thread Diameter |
|---|---|---|
| Bolt A | 40 mm (1.57 in.) | 8.0 mm (0.315 in.) |
| Bolt B | 25 mm (0.984 in.) | 8.0 mm (0.315 in.) |
Tighten the 20 bolts in the order shown in the illustration.
Check the torque of bolt 1 after tightening bolt 20.
11303A
23.INSTALL FRONT CRANKSHAFT OIL SEAL
12101
24.INSTALL OIL PAN SUB-ASSEMBLY
Clean and degrease the contact surfaces of the oil pan sub-assembly and cylinder block sub-assembly.
|
Seal Packing |
Apply seal packing in a continuous line as shown in the illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
3.5 to 4.5 mm (0.138 to 0.177 in.)
Remove any oil from the contact surface.
Install the oil pan sub-assembly within 3 minutes and tighten the bolts and nuts within 10 minutes after applying seal packing.
Do not add engine oil within 2 hours after installation.
Do not start the engine for at least 2 hours after installation.
|
Bolt |
|
Nut |
Install the oil pan sub-assembly to the cylinder block sub-assembly with the 23 bolts and 2 nuts.
Check the torque of all nuts and bolts labeled A again.
89491
25.INSTALL ENGINE OIL LEVEL SENSOR
11201
26.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY
Apply a light coat of engine oil to the O-ring of the camshaft position sensor.
Install a new cylinder head cover gasket, No. 2 cylinder head cover gasket and 2 camshaft bearing cap oil hole gaskets to the cylinder head cover sub-assembly.
Clean and degrease the contact surfaces of the cylinder head cover sub-assembly and cylinder head sub-assembly.
Apply seal packing as shown in the illustration.
| *1 | Timing Chain Cover Sub-assembly | *2 | Timing Chain Case Assembly |
| *3 | Cylinder Head Sub-assembly | *4 | No. 3 Camshaft Bearing Cap |
| *a | Seal Diameter: 3.0 to 6.0 mm (0.118 to 0.236 in.) | *b | Application Width: 7.0 mm (0.276 in.) |
| *c | Application Width: 9.0 mm (0.354 in.) | *d | Application Width: 11.0 mm (0.433 in.) |
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
3.0 to 6.0 mm (0.118 to 0.236 in.)
Remove any oil from the contact surface.
Install the cylinder head cover sub-assembly within 3 minutes and tighten the bolts within 10 minutes after applying seal packing.
Do not add engine oil for at least 2 hours after installation.
Do not start the engine within 2 hours after installation.
|
Bolt |
|
Nut |
|
Nozzle Holder Clamp Seat |
Tighten the 14 bolts, 4 nozzle holder clamp seats, 2 nuts and camshaft position sensor in the order shown in the illustration.
When reusing the camshaft position sensor, check the O-rings.
Make sure that the O-ring is not cracked or jammed when installing it on the cylinder head cover sub-assembly.
Replace with a new part if it is dropped or if it receives a strong impact.
Check the torque of bolts 1 to 4 again.
23682
27.INSTALL NOZZLE HOLDER GASKET
23670
28.TEMPORARILY INSTALL INJECTOR ASSEMBLY
12501
29.INSTALL GENERATOR BRACKET SUB-ASSEMBLY
12281A
30.INSTALL NO. 1 ENGINE HANGER
16575C
31.INSTALL NO. 1 WATER HOSE CLAMP BRACKET (w/ DPF)
13471
32.INSTALL CRANKSHAFT PULLEY (for Automatic Transmission)
13407
33.INSTALL CRANKSHAFT DAMPER SUB-ASSEMBLY (for Manual Transmission)
13496
34.INSTALL CRANKSHAFT PULLY COVER (for Automatic Transmission)
88451B
35.INSTALL VISCOUS HEATER CRANKSHAFT PULLEY (w/ Viscous Heater)
16620
36.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY
Install the V-ribbed belt tensioner assembly to the timing chain cover sub-assembly with the 3 bolts.
16603
37.INSTALL NO. 1 IDLER PULLEY SUB-ASSEMBLY
Install the No. 1 idler pulley sub-assembly to the generator bracket sub-assembly with the bolt.
16331A
38.INSTALL THERMOSTAT
16321
39.INSTALL WATER INLET
16304
40.INSTALL WATER OUTLET SUB-ASSEMBLY
16207
41.INSTALL NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY
15407
42.TEMPORARILY INSTALL TURBO OIL INLET PIPE SUB-ASSEMBLY
17141
43.TEMPORARILY INSTALL EXHAUST MANIFOLD WITH TURBOCHARGER SUB-ASSEMBLY
15474
44.INSTALL TURBO OIL OUTLET PIPE
17293
45.TEMPORARILY INSTALL TURBOCHARGER STAY
17141
46.TIGHTEN EXHAUST MANIFOLD WITH TURBOCHARGER SUB-ASSEMBLY
17293
47.TIGHTEN TURBOCHARGER STAY
87101
48.INSTALL NO. 1 VISCOUS HEATER BRACKET SUB-ASSEMBLY (w/ Viscous Heater)
16284
49.CONNECT NO. 1 AND NO. 2 TURBO WATER HOSE
16268
50.INSTALL NO. 1 WATER BY-PASS PIPE
51.INSTALL WATER BY-PASS HOSE (for Water Cooled Compressor Housing Turbocharger)
16279
52.INSTALL NO. 3 WATER BY-PASS PIPE
12261
53.INSTALL PCV HOSE (except Cold Area Specification Vehicles)
89463C
54.INSTALL NO. 1 NITROGEN OXIDES SENSOR (w/ Exhaust Gas Temperature Sensor for EGR)
17291
55.INSTALL TURBINE OUTLET ELBOW (w/o EGR Cooler)
25051
56.INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (w/ EGR Cooler)
57.INSTALL NO. 2 EXHAUST PIPE SUPPORT STAY (w/o DPF)
w/ EGR Cooler:
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>MONOLITHIC CONVERTER (w/o DPF)>INSTALLATION
w/o EGR Cooler:
Click hereEngine / Hybrid System>1GD-FTV (ENGINE MECHANICAL)>ENGINE UNIT>INSTALLATION
58.INSTALL NO. 2 EXHAUST PIPE SUPPORT STAY (w/ DPF)
89463C
59.CONNECT NO. 1 NITROGEN OXIDES SENSOR (w/ Exhaust Gas Temperature Sensor for EGR)
17271
60.INSTALL NO. 1 TURBO INSULATOR (w/o DPF)
w/ EGR Cooler:
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>MONOLITHIC CONVERTER (w/o DPF)>INSTALLATION
w/o EGR Cooler:
Click hereEngine / Hybrid System>1GD-FTV (ENGINE MECHANICAL)>ENGINE UNIT>INSTALLATION
17271
61.INSTALL NO. 1 TURBO INSULATOR (w/ DPF)
17167
62.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR (w/o DPF)
w/ EGR Cooler:
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>MONOLITHIC CONVERTER (w/o DPF)>INSTALLATION
w/o EGR Cooler:
Click hereEngine / Hybrid System>1GD-FTV (ENGINE MECHANICAL)>ENGINE UNIT>INSTALLATION
17167
63.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR (w/ DPF)
89467B
64.INSTALL AIR FUEL RATIO SENSOR (w/o Exhaust Gas Temperature Sensor for EGR)
23295D
65.INSTALL NO. 1 INJECTOR HOLDER (w/ DPF)
16281
66.CONNECT NO. 4 WATER BY-PASS HOSE (w/ DPF)
16282
67.INSTALL NO. 5 WATER BY-PASS HOSE (w/ DPF)
12229
68.INSTALL PCV PIPE (for Cold Area Specification Vehicles)
16632B
69.INSTALL NO. 2 IDLER PULLEY BRACKET (w/o Air Conditioning System)
88431
70.INSTALL NO. 1 COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning System)
88320
71.INSTALL COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System)
44781
72.INSTALL HOSE BRACKET
23701
73.TEMPORARILY INSTALL NO. 1 AND NO. 2 INJECTION PIPE SUB-ASSEMBLY
23670
74.TIGHTEN INJECTOR ASSEMBLY
23701
75.TIGHTEN NO. 1 AND NO. 2 INJECTION PIPE SUB-ASSEMBLY
76.INSTALL WIRING HARNESS CLAMP BRACKET
23760
77.INSTALL NOZZLE LEAKAGE PIPE ASSEMBLY
23811H
78.INSTALL NO. 1 FUEL PIPE (w/ DPF)
79.INSTALL WIRING HARNESS CLAMP BRACKET
17111
80.INSTALL INTAKE MANIFOLD
23770
81.INSTALL NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY
23804C
82.INSTALL FUEL INLET PIPE SUB-ASSEMBLY
23815D
83.INSTALL NO. 3 FUEL PIPE (w/ Pressurized Fuel Filter)
23804D
84.INSTALL NO. 4 FUEL PIPE (w/ Pressurized Fuel Filter)
23804D
85.INSTALL NO. 4 FUEL PIPE SUB-ASSEMBLY (w/ DPF)
23271H
86.INSTALL NO. 1 FUEL HOSE
23273H
87.INSTALL NO. 2 FUEL HOSE
23243B
88.INSTALL FUEL PUMP MOTOR WIRE
22803
89.INSTALL FUEL INJECTION PUMP COVER SUB-ASSEMBLY
17118
90.INSTALL MANIFOLD STAY
91.INSTALL WIRING HARNESS CLAMP BRACKET
23812D
92.INSTALL NO. 2 FUEL PIPE
11409
93.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE
25624
94.INSTALL EGR VALVE ADAPTER (w/o EGR System)
95.INSTALL EGR VALVE ADAPTER SUB-ASSEMBLY WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY (w/ EGR System without EGR Cooler)
25800
96.INSTALL NO. 1 EGR COOLER AND NO. 2 EGR VALVE ASSEMBLY WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY (w/ EGR System with EGR Cooler)
16209
97.INSTALL NO. 4 WATER BY-PASS PIPE SUB-ASSEMBLY
25804
98.INSTALL VACUUM CONTROL VALVE SET (w/ EGR Cooler)
25601
99.INSTALL EGR PIPE WITH COOLER SUB-ASSEMBLY (for Laminated EGR Pre-cooler)
25601
100.INSTALL NO. 1 EGR PIPE SUB-ASSEMBLY (w/ EGR System)
27148A
101.INSTALL CONNECTING WIRE
16206B
102.INSTALL NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY (w/o EGR Cooler)
16206B
103.INSTALL NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY (w/ EGR Cooler)
25612
104.INSTALL NO. 2 EGR PIPE
89425D
105.INSTALL NO. 5 EXHAUST GAS TEMPERATURE SENSOR (w/ Exhaust Gas Temperature Sensor for EGR)
25625
106.INSTALL EGR VALVE BRACKET
23265C
107.INSTALL GAS FILTER
89421C
108.INSTALL DIESEL TURBO PRESSURE SENSOR
12631A
109.INSTALL ENGINE COVER BRACKET
17578B
110.INSTALL PIPE CLAMP (w/ DPF)
25734
111.TEMPORARILY INSTALL NO. 2 VACUUM PIPE (w/ DPF)
25733A
112.TEMPORARILY INSTALL NO. 1 VACUUM PIPE (w/ DPF)
25734
113.TIGHTEN NO. 2 VACUUM PIPE (w/ DPF)
25733A
114.TIGHTEN NO. 1 VACUUM PIPE (w/ DPF)
89425
115.INSTALL EXHAUST GAS TEMPERATURE SENSOR (w/ DPF)
89481B
116.INSTALL DIFFERENTIAL PRESSURE SENSOR (w/ DPF)
16278
117.INSTALL NO. 2 WATER BY-PASS PIPE
26100G
118.INSTALL DIESEL THROTTLE BODY ASSEMBLY
82121
119.INSTALL ENGINE WIRE
12632
120.INSTALL NO. 2 ENGINE COVER BRACKET
121.INSTALL ENGINE ASSEMBLY