1.REMOVE REAR WHEEL
2.DRAIN BRAKE FLUID
If brake fluid leaks onto any painted surface, immediately wash it off.
3.DRAIN DIFFERENTIAL OIL
17430
4.REMOVE TAIL EXHAUST PIPE ASSEMBLY
37100
5.REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY
89408D
6.REMOVE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY (w/ Height Control Sensor)
89546
7.SEPARATE REAR SPEED SENSOR LH
89545
8.SEPARATE REAR SPEED SENSOR RH
Perform the same procedure as for the LH side.
42312B
9.REMOVE REAR AXLE SHAFT NUT LH
42311N
10.REMOVE REAR AXLE SHAFT NUT RH
Perform the same procedure as for the LH side.
11.REMOVE REAR DISC BRAKE CALIPER ASSEMBLY LH
12.REMOVE REAR DISC BRAKE CALIPER ASSEMBLY RH
Perform the same procedure as for the LH side.
42491
13.REMOVE PARKING BRAKE SHOE ADJUSTING HOLE PLUG
Remove the 2 parking brake shoe adjusting hole plugs.
42431
14.REMOVE REAR DISC
Remove the 2 rear discs.
Click hereBrake>BRAKE (REAR)>REAR BRAKE>REMOVAL
42440
15.REMOVE REAR AXLE HUB AND BEARING ASSEMBLY LH
42410
16.REMOVE REAR AXLE HUB AND BEARING ASSEMBLY RH
Perform the same procedure as for the LH side.
48802
17.REMOVE REAR STABILIZER LINK SUB-ASSEMBLY LH
48802
18.REMOVE REAR STABILIZER LINK SUB-ASSEMBLY RH
Perform the same procedure as for the LH side.
48812
19.REMOVE REAR STABILIZER BAR
48508
20.LOOSEN REAR LOWER SHOCK ABSORBER BRACKET SUB-ASSEMBLY LH
Loosen the 2 bolts to remove the rear axle carrier sub-assembly LH after removing the rear trailing arm assembly LH.
Do not remove the bolts.
48507A
21.LOOSEN REAR LOWER SHOCK ABSORBER BRACKET SUB-ASSEMBLY RH
Perform the same procedure as for the LH side.
48740F
22.REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY LH
48730F
23.REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY RH
Perform the same procedure as for the LH side.
24.LOOSEN PARKING BRAKE ASSEMBLY (for LH Side)
25.LOOSEN PARKING BRAKE ASSEMBLY (for RH Side)
Perform the same procedure as for the LH side.
48780E
26.REMOVE REAR TRAILING ARM ASSEMBLY LH
48760E
27.REMOVE REAR TRAILING ARM ASSEMBLY RH
Perform the same procedure as for the LH side.
28.SEPARATE PARKING BRAKE ASSEMBLY (for LH Side)
29.SEPARATE PARKING BRAKE ASSEMBLY (for RH Side)
Perform the same procedure as for the LH side.
42305
30.REMOVE REAR AXLE CARRIER SUB-ASSEMBLY LH
Remove the bolt (A) and nut, and separate the rear upper control arm assembly LH from the rear axle carrier sub-assembly LH.
Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.
Remove the nut (B), spacer, 2 bolts (C) and rear axle carrier sub-assembly LH.
Be careful not to damage the rear drive shaft outboard joint boot.
Use wire or an equivalent tool to keep the rear drive shaft assembly from hanging.
42304
31.REMOVE REAR AXLE CARRIER SUB-ASSEMBLY RH
Use the same procedure as for the LH side.
42340B
32.REMOVE REAR DRIVE SHAFT ASSEMBLY LH
42330
33.REMOVE REAR DRIVE SHAFT ASSEMBLY RH
Use the same procedure as for the LH side.
42360A
34.REMOVE REAR DRIVE SHAFT SNAP RING LH
42360A
35.REMOVE REAR DRIVE SHAFT SNAP RING RH
Use the same procedure as for the LH side.
41110
36.REMOVE REAR DIFFERENTIAL CARRIER ASSEMBLY WITH DIFFERENTIAL SUPPORT
37.SEPARATE FRAME WIRE
Remove the bolt and disconnect each connector, and then disengage each clamp to separate the frame wire from the rear suspension member sub-assembly as shown in the illustration.
The connector (A) and the clamp (B) are only on vehicles with the LED headlight system.
51206A
38.REMOVE REAR SUSPENSION MEMBER SUB-ASSEMBLY
| *a | Engine Lifter |
| *b | Attachment |
| *c | Wooden Block |
|
Attachment placement location |
Support the rear suspension member sub-assembly with an engine lifter using 2 wooden blocks and 2 attachments or equivalent tools as shown in the illustration.
Make sure to secure the rear suspension member sub-assembly to prevent it from dropping.
Use the attachments to keep the rear suspension member sub-assembly level.
The rear suspension member sub-assembly is a heavy component. Make sure that it is supported securely.
Remove the 4 bolts, 2 nuts, 2 rear lower suspension braces, rear lower suspension member stopper LH and rear lower suspension member stopper RH.
48720A
39.REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY LH
Remove the bolt, nut and rear No. 1 suspension arm assembly LH from the rear suspension member sub-assembly.
Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.
48710A
40.REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY RH
Perform the same procedure as for the LH side.
52272
41.REMOVE REAR SUSPENSION MEMBER UPPER STOPPER
Remove the 2 rear suspension member upper stoppers from the rear suspension member sub-assembly.
52277B
42.REMOVE REAR SUSPENSION MEMBER REAR UPPER STOPPER
Remove the 2 rear suspension member rear upper stoppers from the rear suspension member sub-assembly.
89546
43.REMOVE REAR SPEED SENSOR LH
Remove the 2 bolts, nut and rear speed sensor LH from the rear suspension member sub-assembly.
89545
44.REMOVE REAR SPEED SENSOR RH
Perform the same procedure as for the LH side.
48790
45.REMOVE REAR UPPER CONTROL ARM ASSEMBLY LH
48770A
46.REMOVE REAR UPPER CONTROL ARM ASSEMBLY RH
Perform the same procedure as for the LH side.
41651A
47.REMOVE REAR NO. 2 DIFFERENTIAL MOUNT CUSHION
52271D
48.REMOVE REAR SUSPENSION MEMBER FRONT BODY MOUNTING CUSHION (for LH Side)
| *a | Bend Portion |
Using a chisel and hammer, bend the 2 portions of the rear suspension member front body mounting cushion rib.
Make sure to bend the 2 portions of the cushion rib until the claws of SST can fit securely.
Install SST as shown in the illustration.
Apply grease to the threads and tip of the SST center bolt before use.
| *a | Turn |
| *b | Hold |
Using SST, remove the rear suspension member front body mounting cushion while applying grease into the clearance between the rear suspension member front body mounting cushion and the rear suspension member sub-assembly.
Set the claws of SST onto the rear suspension member sub-assembly securely as shown in the illustration.
Be careful as the rear suspension member front body mounting cushion may fly out.
The rear suspension member front body mounting cushion cannot be reused.
Remove SST and the rear suspension member front body mounting cushion (LH Side) from the rear suspension member sub-assembly.
52271D
49.REMOVE REAR SUSPENSION MEMBER FRONT BODY MOUNTING CUSHION (for RH Side)
Perform the same procedure as for the LH side.
52276A
50.REMOVE REAR SUSPENSION MEMBER REAR BODY MOUNTING CUSHION LH
| *a | Bend Portion |
Using a chisel and hammer, bend the 2 portions of the rear suspension member rear body mounting cushion LH rib.
Make sure to bend the 2 portions of the cushion rib until the claws of SST can fit securely.
Install SST as shown in the illustration.
Apply grease to the threads and tip of the SST center bolt before use.
| *a | Turn |
| *b | Hold |
Using SST, remove the rear suspension member rear body mounting cushion LH while applying grease into the clearance between the rear suspension member rear body mounting cushion LH and the rear suspension member sub-assembly.
Set the claws of SST onto the rear suspension member sub-assembly securely as shown in the illustration.
Be careful as the rear suspension member rear body mounting cushion LH may fly out.
The rear suspension member rear body mounting cushion LH cannot be reused.
Remove SST and the rear suspension member rear body mounting cushion LH from the rear suspension member sub-assembly.
52275B
51.REMOVE REAR SUSPENSION MEMBER REAR BODY MOUNTING CUSHION RH
Perform the same procedure as for the LH side.
52.REMOVE HOLE PLUG
Remove the 13 hole plugs from the rear suspension member sub-assembly as shown in the illustration.