Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM27T0E _51 Engine / Hybrid System _053657 1GR-FE ENGINE CONTROL _0260436 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P1603  Engine Stall History  P1605  Rough Idling  


DESCRIPTION

P1603

After starting the engine, this DTC is stored when the engine stops without the engine switch being operated.

Using the GTS, the conditions present when the DTC was stored can be confirmed by referring to the freeze frame data. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.

It is necessary to check if the vehicle has run out of fuel before performing troubleshooting, as this DTC is also stored when the engine stalls due to running out of fuel.

DTC No. DTC Detection Condition Trouble Area
P1603 After monitoring for startability problems (P1604) finishes and 2 seconds or more elapse after starting the engine, with the engine running, the engine stops (the engine speed drops to 200 rpm or less) without the engine switch being operated for 0.5 seconds or more (1 trip detection logic).
·

Air leak in intake system

·

Purge VSV

·

Mass air flow meter

·

Engine coolant temperature sensor

·

Thermostat

·

Power supply circuit (purge VSV, air fuel ratio sensor, fuel injector assembly, ignition coil assembly)

·

Fuel pump

·

Fuel pump control circuit

·

Fuel line

·

PCV valve and hose

·

Camshaft timing oil control valve

·

Knock sensor

·

Ignition system

·

Air conditioning system

·

Power steering system

·

Electrical load signal system

·

Charging system

·

A/T system

·

Park/neutral position switch assembly

·

ECM

·

Wire harness or connector

·

Immobiliser system



P1605

This DTC is stored if the engine speed drops below the set speed without the engine switch being operated.

Using the GTS, the conditions present when the DTC was stored can be confirmed by referring to the freeze frame data. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.

It is necessary to check if the vehicle ran out of fuel before performing troubleshooting, as this DTC is also stored when idling is unstable due to running out of fuel.

DTC No. DTC Detection Condition Trouble Area
P1605 After 5 seconds or more elapse after starting the engine, with the engine running, the engine speed drops to 400 rpm or less without the engine switch being operated (1 trip detection logic).
·

Air leak in intake system

·

Purge VSV

·

Mass air flow meter

·

Engine coolant temperature sensor

·

Thermostat

·

Power supply circuit (purge VSV, air fuel ratio sensor, fuel injector assembly, ignition coil assembly)

·

Fuel pump

·

Fuel pump control circuit

·

Fuel line

·

PCV valve and hose

·

Camshaft timing oil control valve

·

Knock sensor

·

Ignition system

·

Air conditioning system

·

Power steering system

·

Electrical load signal system

·

Charging system

·

A/T system

·

Park/neutral position switch assembly

·

ECM

·

Wire harness or connector

·

Immobiliser system



CAUTION / NOTICE / HINT

HINT:
·

In contrast to normal malfunction diagnosis for components, circuits and systems, DTCs P1603 and P1605 are used to determine the malfunctioning area from the problem symptoms and freeze frame data when the user mentions problems such as engine stall.

As these DTCs can be stored as a result of certain user actions, even if these DTCs are output, if the customer makes no mention of problems, clear these DTCs without performing any troubleshooting and return the vehicle to the customer.

·

If any other DTCs are output, perform troubleshooting for those DTCs first.

·

Use any information from the customer problem analysis about the condition of the vehicle at the time when the problem occurred (how the engine stopped, conditions when the engine was restarted, etc.) as a reference.

Symptom Suspected Area
Engine vibration occurs and engine stops Air-fuel ratio abnormal
Engine stops with no engine vibration Ignition system, injection stoppage, high load from external parts
Engine can be started with accelerator pedal depressed Insufficient air volume
Rough idling after engine started Air-fuel ratio abnormal, abnormal combustion

·

Read freeze frame data using the GTS. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.

·

When confirming the freeze frame data, be sure to check all 5 sets of freeze frame data (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA).

·

When DTC P1603 (Engine Stall History) is stored, DTC P1605 (Rough Idling) is also stored. When confirming freeze frame data, check DTC P1605. The ECM stores DTC P1605 first. Therefore, 5 sets of freeze frame data can be confirmed through DTC P1605, enabling the technician to obtain more information.

·

When confirming freeze frame data, if there are multiple items related to the cause of the malfunction, perform troubleshooting for all related items.

·

Try to operate the vehicle under the conditions recorded in the freeze frame data which were present when the malfunction occurred. Confirm the data at this time and the data when the engine is idling (engine warmed up, no load, and shift lever in D or N) and compare these data with the freeze frame data.

·

Inspections take into account the fact that the malfunction may not have reoccurred and place emphasis on checking the vehicle conditions present at the time when the malfunction occurred.

·

When performing inspections, jiggle the relevant wire harnesses and connectors in an attempt to reproduce malfunctions that do not always occur.



Inspection flow:

Using freeze frame data, narrow down the parts to be inspected according to the vehicle conditions at the time when the malfunction occurred.


P1603:

A226063E01
0.219,0.775 1.114,1.107 0.895,0.332 10 While idling or while driving? 1.824,0.778 3.155,1.478 1.332,0.700 10 Did the engine speed decrease slowly or rapidly when engine stall occurred? 0.189,0.599 0.373,0.783 0.184,0.184 10 1: 1.824,0.599 2.007,0.783 0.184,0.184 10 2: 3.925,0.778 4.961,1.295 1.036,0.517 10 Was the air-fuel ratio abnormal or normal? 3.925,0.599 4.109,0.783 0.184,0.184 10 3: 5.961,0.75 6.904,0.915 0.943,0.165 10 Intake air leak 5.781,1.758 7.031,1.923 1.250,0.165 10 Sensor malfunction 1.242,5.833 2.492,5.998 1.250,0.165 10 Sensor malfunction 5.748,2.763 7.061,2.928 1.313,0.165 10 Fuel supply problem 1.214,7.822 2.527,7.987 1.313,0.165 10 Fuel supply problem 6.036,3.459 6.746,3.809 0.710,0.350 10 Air volume insufficient 5.953,4.47 6.878,4.802 0.924,0.332 10 Ignition timing incorrect 3.41,4.481 4.492,4.822 1.082,0.341 10 Injection and ignition stoppage 1.337,6.554 2.418,6.895 1.082,0.341 10 Injection and ignition stoppage 3.497,5.48 4.394,5.821 0.897,0.341 10 Load from external parts 1.31,0.134 1.697,0.299 0.387,0.165 10 Idling 0.096,2.544 0.557,2.709 0.461,0.165 10 Driving 2.972,0.134 4.156,0.299 1.184,0.165 10 Decreased Slowly 1.16,2.544 2.400,2.746 1.239,0.202 10 Decreased Rapidly 5.027,0.134 5.692,0.317 0.665,0.184 10 Abnormal 3.832,2.544 4.330,2.709 0.498,0.165 10 Normal

1:
·

If the engine stalled when the intake air volume was low (during idling or deceleration), there may be a decrease in torque due to an incorrect air-fuel ratio, etc.

·

If the engine stalled when the intake air volume was high (during driving or acceleration), there may be a major malfunction such as continuous misfire due to ignition stoppage, fuel injection stoppage, etc. and the torque drops to zero.


2:
·

If the engine speed decreased slowly, there may have been a decrease in torque due to an air-fuel ratio that was incorrect (by approximately 20 to 30%), etc.

·

If the engine speed decreased rapidly, there may have been a malfunction such as when the engine misfires almost continuously due to ignition stoppage, fuel injection stoppage, etc., or when the external load increases due to an external part malfunctioning.


3:
·

If the air-fuel ratio is abnormal, there may have been an intake air leak, sensor malfunction, or fuel supply problem.

·

If the vehicle was normal, the air volume may have been insufficient or the ignition timing may have been incorrect.


P1603 inspection flow: Narrow down the parts to be inspected according to the vehicle conditions at the time when the malfunction occurred (freeze frame data).

Vehicle State Engine Speed Suspected Area Primary Parts to Inspect Procedure
Idling or decelerating Slowly decreases and engine stalls Ignition system abnormal Igniter abnormal
·

Power supply circuit

·

Ignition coil assemblies

·

Spark plug


7, 35, 49
Air-fuel ratio abnormal Air suction
·

Intake system connections

·

Purge VSV system


5, 6
Sensor malfunction (value from sensor too lean)
·

Mass air flow meter

·

Engine coolant temperature sensor

·

Air fuel ratio sensor system

·

Thermostat


8 to 20
Sensor malfunction (value from sensor too rich) 36 to 48
Fuel supply problem
·

Fuel pump control circuit

·

Purge VSV system

·

Fuel line

·

ECM


21 to 34
Intake air volume insufficient Problem with air passage
·

Intake system connections

·

Mass air flow meter

·

PCV valve and hose

·

Purge VSV system


50 to 52
Excessive valve overlap
·

Camshaft timing oil control valve


53 to 56
Ignition timing incorrect Does not operate as expected
·

Knock sensor

·

Engine coolant temperature sensor

·

Mass air flow meter


57 to 61
Rapidly decreases and engine stalls Ignition and injection stops (electrical system malfunction) Power temporarily cut
·

Power supply circuit (fuel injector assembly, ignition coil assembly)


62, 63
External part malfunctioning Increase in load
·

Air conditioning system

·

Electrical load signal system

·

Power steering system

·

A/T system

·

Park/neutral position switch assembly


64 to 67
Accelerating - Crankshaft position sensor or VVT sensor malfunction Power temporarily cut
·

Check DTCs


1
Mass air flow meter Foreign matter adhesion
·

Mass air flow meter


68 to 71
Ignition and injection stops (electrical system malfunction) Power temporarily cut
·

Power supply circuit (fuel injector assembly, ignition coil assembly)


72, 73
Fuel supply problem Fuel leak, clog
·

Fuel pump control circuit

·

Fuel line


74 to 78

P1605:

A226064E01
0.498,0.514 0.668,0.688 0.170,0.174 10 1: 0.498,0.71 1.640,1.213 1.142,0.503 10 Did the engine speed decrease slowly or rapidly? 2.819,0.514 2.989,0.688 0.170,0.174 10 2: 2.819,0.71 3.961,1.213 1.142,0.503 10 Was the air-fuel ratio abnormal or normal? 5.69,0.715 6.633,0.881 0.943,0.165 10 Intake air leak 5.549,1.727 6.788,1.892 1.239,0.165 10 Sensor malfunction 5.522,2.722 6.799,2.924 1.276,0.202 10 Fuel supply problem 4.034,2.065 4.742,2.384 0.708,0.319 10 Air volume insufficient 3.925,3.05 4.850,3.382 0.924,0.332 10 Ignition timing incorrect 1.582,2.706 2.673,3.057 1.091,0.350 10 Injection and ignition stoppage 1.662,3.707 2.586,4.057 0.924,0.350 10 Load from external parts 1.908,0.876 2.628,1.226 0.721,0.350 10 Decreased Slowly 0.264,1.847 0.984,2.197 0.721,0.350 10 Decreased Rapidly 4.299,0.894 4.945,1.059 0.647,0.165 10 Abnormal 2.776,1.847 3.293,2.012 0.517,0.165 10 Normal

1:
·

If the engine speed decreased slowly, there may have been a decrease in torque due to an air-fuel ratio that was incorrect (by approximately 20 to 30%), etc.

·

If the engine speed decreased rapidly, there may have been a malfunction such as when the engine misfires almost continuously due to ignition stoppage, fuel injection stoppage, etc., or when the external load increases due to an external part malfunctioning.


2:
·

If the air-fuel ratio is abnormal, there may have been an intake air leak, sensor malfunction, or fuel supply problem.

·

If the vehicle was normal, the air volume may have been insufficient or the ignition timing may have been incorrect.


P1605 inspection flow: Narrow down the parts to be inspected according to the vehicle conditions at the time when the malfunction occurred (freeze frame data).

Engine Speed Suspected Area Primary Parts to Inspect Procedure
Slowly decreases and engine stalls Ignition system abnormal Igniter abnormal
·

Power supply circuit

·

Ignition coil assemblies

·

Spark plug


7, 35, 49
Air-fuel ratio abnormal Air suction
·

Intake system connections

·

Purge VSV system


5, 6
Sensor malfunction (value from sensor too lean)
·

Mass air flow meter

·

Engine coolant temperature sensor

·

Air fuel ratio sensor system

·

Thermostat


8 to 20
Sensor malfunction (value from sensor too rich) 36 to 48
Fuel supply problem
·

Fuel pump control circuit

·

Purge VSV system

·

Fuel line

·

ECM


21 to 34
Intake air volume insufficient Problem with air passage
·

Intake system connections

·

Mass air flow meter

·

PCV valve and hose

·

Purge VSV system


50 to 52
Excessive valve overlap
·

Camshaft timing oil control valve


53 to 56
Ignition timing incorrect Does not operate as expected
·

Knock sensor

·

Engine coolant temperature sensor

·

Mass air flow meter


57 to 61
Rapidly decreases and engine stalls Ignition and injection stops (electrical system malfunction) Power temporarily cut
·

Power supply circuit (fuel injector assembly, ignition coil assembly)


62, 63
External part malfunctioning Increase in load
·

Air conditioning system

·

Electrical load signal system

·

Power steering system

·

A/T system

·

Park/neutral position switch assembly


64 to 67

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Read the DTCs (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
Only DTC P1603 and/or P1605 is output A
DTCs other than P1603 and/or P1605 are output B

HINT:

If any DTCs other than P1603 or P1605 are output, troubleshoot those DTCs first.




A

2.CHECK FREEZE FRAME DATA

B

2.CHECK FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA).

OK:

Immobiliser Fuel Cut is OFF.


Result
Result Proceed to
Abnormal A
Normal B



A

3.CHECK ENGINE IMMOBILISER SYSTEM

B

4.READ FREEZE FRAME DATA
3.CHECK ENGINE IMMOBILISER SYSTEM
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Idle the engine


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Immobiliser Communication and Immobiliser Fuel Cut.


e.

Check the Data List indication.

OK
Data List Item Result
Immobiliser Communication ON
Immobiliser Fuel Cut OFF



OK

4.READ FREEZE FRAME DATA

NG

4.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA).

Result
Problem Symptom Freeze Frame Data Item for DTC P1605 Suspected Area Proceed to
Closed Throttle Position SW Engine Speed Total of Short FT and Long FT
When idling or decelerating, engine speed slowly decreases and engine stalls All 5 sets of freeze frame data are ON Decreases slowly*1 All 5 sets of freeze frame data are +15% or more*2
·

Air suction


·

Sensor malfunction (value from sensor too lean)


·

Fuel supply problem


A
At least 1 of the 5 sets of freeze frame data is -15% or less*3 Sensor malfunction (value from sensor too rich) B
All 5 sets of freeze frame data are from -15% to +15%
·

Intake air volume insufficient


·

Ignition timing incorrect


C
When idling or decelerating, engine speed rapidly decreases and engine stalls Decreases rapidly*1 -
·

Injection stoppage, ignition stoppage


·

Load from external parts


D
When accelerating or driving at constant speed, engine stalls*4 At least one is OFF - -
·

Sensor malfunction


·

Injection stoppage, ignition stoppage


·

Fuel supply problem


E

A215381E01
0.072,0.032 2.177,0.197 2.105,0.165 10 Rapid Decrease in Engine Speed 2.333,0.377 2.702,0.561 0.369,0.184 10 (rpm) 2.389,0.723 2.665,0.869 0.276,0.147 10 800 2.389,0.928 2.665,1.075 0.276,0.147 10 600 2.389,1.126 2.665,1.272 0.276,0.147 10 400 2.389,1.331 2.665,1.478 0.276,0.147 10 200 2.548,1.529 2.689,1.675 0.142,0.147 10 0 3.038,1.642 3.235,1.798 0.198,0.156 10 #1 3.472,1.642 3.670,1.798 0.198,0.156 10 #2 3.935,1.642 4.132,1.798 0.198,0.156 10 #3 4.153,1.642 4.350,1.798 0.198,0.156 10 #4 4.377,1.642 4.574,1.798 0.198,0.156 10 #5 4.985,1.105 6.058,1.261 1.073,0.156 10 400 rpm or more 1.216,1.019 2.122,1.203 0.906,0.184 10 Engine Speed 2.702,1.944 4.816,2.128 2.114,0.184 10 Freeze Frame Data Storage Point

HINT:
·

*1: A rapid decrease in engine speed may be caused by an electrical fault in the shared wiring of all or a number of cylinders, an increase in load from external parts, etc. The engine speed is considered to have decreased rapidly if either of the following conditions applies.

Otherwise, the engine speed is considered to have decreased slowly.

(a)

In the freeze frame data, the decrease in engine speed from #3 to #5 is 400 rpm or more.

(b)

In the freeze frame data, the engine speed at #5 is 120 rpm or less.



·

If the vehicle speed is 30 km/h or less and the difference between Engine Speed and SPD (NT) is 100 rpm or less, inspect the automatic transmission. (Depending on the rate of vehicle deceleration, the engine speed may have decreased due to the A/T lock-up release being late.)

·

*2: When a DTC is stored, feedback compensation increases because the air-fuel ratio is determined to be lean.

·

*3: When a DTC is stored, feedback compensation decreases because the air-fuel ratio is determined to be rich.

·

*4: This item should be checked when DTC P1603 is output and is not necessary to check when only P1605 is output.





A

5.CHECK INTAKE SYSTEM

B

35.CHECK IGNITION SYSTEM

C

49.CHECK IGNITION SYSTEM

D

62.INSPECT TERMINAL VOLTAGE (FUEL INJECTOR POWER SOURCE)

E

68.CHECK FREEZE FRAME DATA
5.CHECK INTAKE SYSTEM
a.

Check for air leakage in the intake system [vacuum hose disconnection, cracks, damaged gaskets, etc.] (See page Engine / Hybrid System>1GR-FE (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION).

HINT:
·

If the accelerator pedal is released after racing the engine, the inspection is easier to perform because the vacuum inside the intake pipes increases and the air suction noise becomes louder.

·

If Short FT and Long FT are largely different from the normal values when idling (the intake air volume is small) and almost the same as the normal values when racing the engine (the intake air volume is high), air leakage may be present.



OK:

There is no air leakage.


HINT:
for Automatic Transmission

Perform "Inspection After Repair" after repairing or replacing the intake system (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




OK

6.CHECK PURGE VSV

NG

REPAIR OR REPLACE INTAKE SYSTEM

6.CHECK PURGE VSV
a.
A172615

Disconnect the purge hose (on the canister side) of the purge VSV.


b.

Start the engine.


c.

Idle the engine.


d.

Disconnect the connector of the purge VSV.


e.

Check if air flows through the purge VSV.

OK:

Air does not flow.



f.

Connect the connector of the purge VSV.


g.

Connect the purge hose of the purge VSV.

HINT:

When this inspection is performed, the MIL may illuminate. After finishing the inspection, check and clear DTCs (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).




OK

7.CHECK IGNITION SYSTEM

NG

7.CHECK IGNITION SYSTEM
a.

Perform ignition system On-vehicle Inspection (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION).

HINT:
for Automatic Transmission

Perform "Inspection After Repair" after repairing or replacing the ignition system (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




OK

8.READ FREEZE FRAME DATA

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

8.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA).

Result
Freeze Frame Data Item for DTC P1605 Result Suspected Area Proceed to
Calculate Load Below 90% of the current value of the vehicle*1 Mass air flow meter A
AFS Voltage B1S1
AFS Voltage B2S1
3.3 V or higher*2
·

Air fuel ratio sensor

·

Wire harness or connector


B

HINT:
·

*1: If the Mass air flow meter is malfunctioning and incorrectly measures the pressure to be less than the actual intake manifold pressure, the freeze frame data will show a low engine load value.

·

*2: If the air fuel ratio sensor is malfunctioning and constantly outputs a value indicating the air-fuel ratio is lean, the actual air-fuel ratio will become rich and the engine may stall.





A

9.CHECK MASS AIR FLOW METER

B

12.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
9.CHECK MASS AIR FLOW METER
a.

Remove the Mass air flow meter.


b.

Check for foreign matter in the airflow passage of the mass airflow meter.

Result
Result Proceed to
Visible foreign matter is not present A
Visible foreign matter is present B

HINT:
for Automatic Transmission

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




A

10.CHECK HARNESS AND CONNECTOR (ECM - MASS AIR FLOW METER)

B

10.CHECK HARNESS AND CONNECTOR (ECM - MASS AIR FLOW METER)
a.

Check the harnesses and connectors, referring to DTC P0102 inspection procedure (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>P0102).

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.





OK

11.PERFORM DRIVE TEST

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.PERFORM DRIVE TEST
a.

Connect the GTS to the DLC3.


b.

Start the engine and warm it up until the engine coolant temperature stabilizes.

HINT:

The A/C switch and all accessory switches should be off.



c.

Idle the engine.


d.

Using the GTS, read the value of Calculate Load in the Data List.

Standard:
Data List Specified Condition
Calculate Load 90 to 110% of the current value of the vehicle


Result
Result Proceed to
Abnormal A
Normal B

HINT:
for Automatic Transmission

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




A

B

15.READ FREEZE FRAME DATA
12.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Start the engine, turn off all accessory switches and warm up the engine until the engine coolant temperature stabilizes.


d.

Idle the engine.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.


f.

Read the output voltage from the air fuel ratio sensor when increasing and decreasing the fuel injection volume.

A358304E01
0.135,0.219 1.323,0.406 1.188,0.188 10 false Injection Volume 0.156,0.865 0.75,1.083 0.594,0.219 10 false +12.5% 0.177,1.125 0.729,1.323 0.552,0.198 10 false -12.5% 1.885,0.208 4.354,0.406 2.469,0.198 10 false Air Fuel Ratio Sensor Output Voltage 2.042,0.927 3.198,1.115 1.156,0.188 10 false Higher than 3.4 V 2.365,1.229 3.229,1.417 0.865,0.188 10 false Below 3.1 V 4.563,0.875 5.719,1.063 1.156,0.188 10 false Higher than 0.55 V 4.958,1.177 5.823,1.365 0.865,0.188 10 false Below 0.4 V 4.542,0.198 7.01,0.396 2.469,0.198 10 false Heated Oxygen Sensor Output Voltage 4.063,1.063 4.375,1.26 0.313,0.198 10 false OK 6.635,1.021 6.948,1.219 0.313,0.198 10 false OK

Standard:
GTS Display Specified Condition
Control the Injection Volume for A/F Sensor (+12.5%) Air fuel ratio sensor output voltage is below 3.1 V
Control the Injection Volume for A/F Sensor (-12.5%) Air fuel ratio sensor output voltage is higher than 3.4 V


Result
Result Proceed to
Abnormal A
Normal B

HINT:

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.




A

13.CHECK TERMINAL VOLTAGE (AIR FUEL RATIO SENSOR POWER SOURCE)

B

15.READ FREEZE FRAME DATA
13.CHECK TERMINAL VOLTAGE (AIR FUEL RATIO SENSOR POWER SOURCE)
a.

Check the harnesses and connectors, referring to DTC P0031 inspection procedure (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>P0031).

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.





OK

14.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)

NG

REPAIR AIR FUEL RATIO SENSOR POWER SOURCE CIRCUIT

14.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
a.

Check the harnesses and connectors, referring to DTC P2237 inspection procedure (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>P2237).

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.





OK

15.READ FREEZE FRAME DATA

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA).

Result
Freeze Frame Data Item for DTC P1605 Result Proceed to
Initial Engine Coolant Temp, Ambient Temp for A/C, Initial Intake Air Temp Difference in temperature between each item is less than 10°C*1 A
Difference in temperature between each item is 10°C or more*2 B

HINT:
·

*1: A long time had elapsed after stopping the engine.

·

*2: A long time had not elapsed after stopping the engine.





A

16.READ FREEZE FRAME DATA

B

18.READ FREEZE FRAME DATA
16.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA).

A217929E01
0.467,0.856 2.887,1.519 2.420,0.663 10 Engine Coolant Temperature Increase after Engine Start (Engine Coolant Temperature - Engine Coolant Temperature at Engine Start) 3.423,0.037 3.718,0.234 0.295,0.198 10 (°C) 5.609,2.116 6.223,2.286 0.614,0.170 10 (Minutes) 5.16,1.69 5.316,1.846 0.156,0.156 10 A 4.964,0.779 5.120,0.935 0.156,0.156 10 C 3.891,0.493 4.047,0.649 0.156,0.156 10 B 3.563,2.39 5.573,2.546 2.010,0.156 10 Time Elapsed after Engine Start

Result
Freeze Frame Data Item for DTC P1605 Result Suspected Area Proceed to
Initial Engine Coolant Temp, Coolant Temp, Engine Run Time Range A
·

Engine coolant temperature sensor

·

Thermostat


A
Range B Engine coolant temperature sensor B
Range C - C

HINT:

This step is not directly related to engine stall.




A

17.INSPECT THERMOSTAT

B

19.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

C

21.READ FREEZE FRAME DATA
17.INSPECT THERMOSTAT
HINT:

For the thermostat inspection, refer to the following procedures (See page Engine / Hybrid System>1GR-FE (COOLING)>THERMOSTAT>INSPECTION).


Result
Result Proceed to
Abnormal A
Normal B


A

B

19.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
18.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA).

Result
Freeze Frame Data Item for DTC P1605 Result Suspected Area Proceed to
Coolant Temp 120°C or higher Engine coolant temperature sensor A
Coolant Temp, Ambient Temp for A/C Engine coolant temperature is lower than outside temperature by 15°C or more Engine coolant temperature sensor
Both freeze frame data items listed above Values are other than above - B



A

19.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

B

21.READ FREEZE FRAME DATA
19.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
HINT:

For the engine coolant temperature sensor inspection, refer to the following procedures (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>ENGINE COOLANT TEMPERATURE SENSOR>INSPECTION).


Result
Result Proceed to
Normal A
Abnormal B

HINT:
for Automatic Transmission

Perform "Inspection After Repair" after replacing the engine coolant temperature sensor (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).



A

20.CHECK HARNESS AND CONNECTOR (ECM - ENGINE COOLANT TEMPERATURE SENSOR)

B

20.CHECK HARNESS AND CONNECTOR (ECM - ENGINE COOLANT TEMPERATURE SENSOR)
a.

Check the harnesses and connectors, referring to DTC P0115 inspection procedure (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>P0115).


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.




OK

21.READ FREEZE FRAME DATA

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

21.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA).

Result
Freeze Frame Data Item for DTC P1605 Result Suspected Area Proceed to
EVAP (Purge) VSV At least 1 of the 5 sets of freeze frame data is not 0% Purge VSV A
All 5 sets of freeze frame data are 0% - B

HINT:

If the purge VSV is stuck closed, air-fuel ratio compensation by the purge VSV is incorrectly adjusted, and then the air-fuel ratio becomes lean and the engine may stall.




A

22.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VSV FOR EVAP CONTROL)

B

30.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP / SPEED)
22.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VSV FOR EVAP CONTROL)
a.
A200511E01
0.55,0.157 1.109,0.306 0.559,0.149 10 VSV ON 2.222,0.157 2.843,0.306 0.621,0.149 10 VSV OFF 0.593,1.471 1.152,1.627 0.559,0.156 10 Air flows 1.985,1.471 3.058,1.627 1.073,0.156 10 Air does not flow

Disconnect the purge hose (on the canister side) of the purge VSV.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG).


d.

Start the engine.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Evap Control.


f.

Operate the purge VSV and check the airflow.

OK:
Activate the VSV for Evap Control Specified Condition
ON Air flows
OFF Air does not flow


Result
Result Proceed to
NG A
OK B


HINT:

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.



A

23.INSPECT PURGE VSV

B

30.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP / SPEED)
23.INSPECT PURGE VSV

OK

24.CHECK TERMINAL VOLTAGE (PURGE VSV POWER SOURCE)

NG

24.CHECK TERMINAL VOLTAGE (PURGE VSV POWER SOURCE)
a.

Check the harnesses and connectors, referring to DTC P0443 inspection procedure (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>P0443).


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.




OK

25.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)

NG

REPAIR PURGE VSV POWER SOURCE CIRCUIT

25.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)
a.

Check the harnesses and connectors, referring to DTC P0443 inspection procedure (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>P0443).


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.




OK

26.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

26.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.




NEXT

27.READ VALUE USING GTS (EVAP (Purge) VSV)
27.READ VALUE USING GTS (EVAP (Purge) VSV)
a.

Connect the GTS to the DLC3.


b.

Start the engine and warm it up until the engine coolant temperature stabilizes.

HINT:

The A/C switch and all accessory switches should be off.



c.

Idle the engine for 15 minutes or more.


d.

Using the GTS, read the value of EVAP (Purge) VSV in the Data List.

Standard:
Data List Specified Condition
EVAP (Purge) VSV Value other than 0% is displayed


Result
Result Proceed to
Abnormal A
Normal B



A

28.PERFORM ACTIVE TEST USING GTS

B

28.PERFORM ACTIVE TEST USING GTS
a.
A200511E01
0.55,0.157 1.109,0.306 0.559,0.149 10 VSV ON 2.222,0.157 2.843,0.306 0.621,0.149 10 VSV OFF 0.593,1.471 1.152,1.627 0.559,0.156 10 Air flows 1.985,1.471 3.058,1.627 1.073,0.156 10 Air does not flow

Disconnect the purge hose (on the canister side) of the purge VSV.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG).


d.

Start the engine.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Evap Control.


f.

Operate the purge VSV and check the airflow.

OK:
Activate the VSV for Evap Control Specified Condition
ON Air flows
OFF Air does not flow


Result
Result Proceed to
NG A
OK B


HINT:

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.



A

29.CHECK CONNECTOR CONNECTION CONDITION (ECM)

B

29.CHECK CONNECTOR CONNECTION CONDITION (ECM)
a.

Check the ECM connector connection condition.

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.





OK

NG

RECONNECT CONNECTOR CORRECTLY

30.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP / SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.


e.

When performing the Active Test, check for an operating sound from the fuel pump.

Standard:
Control the Fuel Pump / Speed Specified Condition
ON Operating sound heard
OFF Operating sound not heard


Result
Result Proceed to
Abnormal A
Normal B

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

While performing the Active Test, make sure that there is no fuel leakage from the pipes, no signs that fuel has leaked, and no fuel smell.

·

If the fuel pump operating noise is abnormal, proceed to step 31.





A

31.INSPECT FUEL PUMP

B

32.CHECK FUEL SYSTEM
31.INSPECT FUEL PUMP
a.

Inspect the fuel pump (for Single Tank Type) (See page Engine / Hybrid System>1GR-FE (FUEL)>FUEL PUMP (for Single Tank Type)>INSPECTION).


b.

Inspect the fuel pump (for Double Tank Type) (See page Engine / Hybrid System>1GR-FE (FUEL)>FUEL PUMP (for Double Tank Type)>INSPECTION).

Result
Result Proceed to
OK A
NG (for Single Tank Type) B
NG (for Double Tank Type) C

HINT:
for Automatic Transmission

Perform "Inspection After Repair" after replacing the fuel pump (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




A

B

REPLACE FUEL PUMP (FOR SINGLE TANK TYPE)

C

REPLACE FUEL PUMP (FOR DOUBLE TANK TYPE)

32.CHECK FUEL SYSTEM
a.

Check the fuel system.

·

Check the fuel pump operation.

·

Check for fuel leaks.

·

Check the fuel pressure.

·

Perform the Active Test [Control the Select Cylinder Fuel Cut].



HINT:

For the fuel system On-vehicle Inspection, refer to the following procedures (See page Engine / Hybrid System>1GR-FE (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION).


Result
Result Proceed to
Abnormal A
Normal B


A

33.CHECK FUEL SYSTEM

B

33.CHECK FUEL SYSTEM
a.

Check for foreign matter such as iron particles around the fuel pump (fuel pump, fuel pump filter and inside the fuel tank), and for signs that the fuel pump was stuck.

Result
Result Proceed to
There is no foreign matter and no signs that fuel pump was stuck A
There is foreign matter or signs that fuel pump was stuck B

HINT:

If there is foreign matter such as iron particles on the fuel pump, fuel filter or fuel tank, remove the foreign matter.




A

34.CHECK FUEL SYSTEM

B

REPAIR OR REPLACE FUEL SYSTEM

34.CHECK FUEL SYSTEM
a.

Check the fuel system.

·

Check the fuel pump operation.

·

Check for fuel leaks.

·

Check the fuel pressure.

·

Perform the Active Test [Control the Select Cylinder Fuel Cut].



HINT:

For the fuel system On-vehicle Inspection, refer to the following procedures (See page Engine / Hybrid System>1GR-FE (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION).



OK

END

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

35.CHECK IGNITION SYSTEM
a.

Perform ignition system On-vehicle Inspection (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION).

HINT:
for Automatic Transmission

Perform "Inspection After Repair" after repairing or replacing the ignition system (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




OK

36.READ FREEZE FRAME DATA

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

36.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA).

Result
Freeze Frame Data Item for DTC P1605 Result Suspected Area Proceed to
Calculate Load 110% or more of the current value of the vehicle*1 Mass air flow meter A
AFS Voltage B1S1
AFS Voltage B2S1
Below 3.3 V*2
·

Air fuel ratio sensor

·

Harness and connector


B
Both freeze frame data items listed above Values are other than above - C

HINT:
·

*1: If the Mass air flow meter is malfunctioning and incorrectly measures the intake air volume to be higher than the actual volume of air flowing through the intake manifold, the freeze frame data will show a high engine load value.

·

*2: As the air fuel ratio sensor output is low before the sensor warms up, the value at that time cannot be used for diagnosis. If the air fuel ratio sensor is malfunctioning and constantly outputs a value indicating the air-fuel ratio is rich, the actual air-fuel ratio will become lean and the engine may stall.





A

37.CHECK MASS AIR FLOW METER

B

40.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

C

43.READ FREEZE FRAME DATA
37.CHECK MASS AIR FLOW METER
a.

Remove the mass airflow meter.


b.

Check for foreign matter in the airflow passage of the Mass air flow meter.

Result
Result Proceed to
Visible foreign matter is not present A
Visible foreign matter is present B

HINT:
for Automatic Transmission

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




A

38.CHECK HARNESS AND CONNECTOR (ECM - MASS AIR FLOW METER)

B

38.CHECK HARNESS AND CONNECTOR (ECM - MASS AIR FLOW METER)
a.

Check the harnesses and connectors, referring to DTC P0102 inspection procedure (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>P0102).

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.





OK

39.PERFORM DRIVE TEST

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

39.PERFORM DRIVE TEST
a.

Connect the GTS to the DLC3.


b.

Start the engine and warm it up until the engine coolant temperature stabilizes.

HINT:

The A/C switch and all accessory switches should be off.



c.

Idle the engine.


d.

Using the GTS, read the value of Calculate Load in the Data List.

Standard:
Data List Specified Condition
Calculate Load 90 to 110% of the current value of the vehicle


HINT:
for Automatic Transmission

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




OK

40.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

NG

40.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Start the engine, turn off all accessory switches and warm up the engine until the engine coolant temperature stabilizes.


d.

Idle the engine.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.


f.

Read the output voltage from the air fuel ratio sensor when increasing and decreasing the fuel injection volume.

A358304E01
0.135,0.219 1.323,0.406 1.188,0.188 10 false Injection Volume 0.156,0.865 0.75,1.083 0.594,0.219 10 false +12.5% 0.177,1.125 0.729,1.323 0.552,0.198 10 false -12.5% 1.885,0.208 4.354,0.406 2.469,0.198 10 false Air Fuel Ratio Sensor Output Voltage 2.042,0.927 3.198,1.115 1.156,0.188 10 false Higher than 3.4 V 2.365,1.229 3.229,1.417 0.865,0.188 10 false Below 3.1 V 4.563,0.875 5.719,1.063 1.156,0.188 10 false Higher than 0.55 V 4.958,1.177 5.823,1.365 0.865,0.188 10 false Below 0.4 V 4.542,0.198 7.01,0.396 2.469,0.198 10 false Heated Oxygen Sensor Output Voltage 4.063,1.063 4.375,1.26 0.313,0.198 10 false OK 6.635,1.021 6.948,1.219 0.313,0.198 10 false OK

Standard:
GTS Display Specified Condition
Control the Injection Volume for A/F Sensor (+12.5%) Air fuel ratio sensor output voltage is below 3.1 V
Control the Injection Volume for A/F Sensor (-12.5%) Air fuel ratio sensor output voltage is higher than 3.4 V


Result
Result Proceed to
Abnormal A
Normal B

HINT:

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.




A

41.CHECK TERMINAL VOLTAGE (AIR FUEL RATIO SENSOR POWER SOURCE)

B

43.READ FREEZE FRAME DATA
41.CHECK TERMINAL VOLTAGE (AIR FUEL RATIO SENSOR POWER SOURCE)
a.

Check the harnesses and connectors, referring to DTC P0031 inspection procedure (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>P0031).

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.





OK

42.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)

NG

REPAIR AIR FUEL RATIO SENSOR POWER SOURCE CIRCUIT

42.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
a.

Check the harnesses and connectors, referring to DTC P2237 inspection procedure (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>P2237).

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.





OK

43.READ FREEZE FRAME DATA

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

43.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA).

Result
Freeze Frame Data Item for DTC P1605 Result Proceed to
Initial Engine Coolant Temp, Ambient Temp for A/C, Initial Intake Air Temp Difference in temperature between each item is less than 10°C*1 A
Difference in temperature between each item is 10°C or more*2 B

HINT:
·

*1: A long time had elapsed after stopping the engine.

·

*2: A long time had not elapsed after stopping the engine.





A

44.READ FREEZE FRAME DATA

B

46.READ FREEZE FRAME DATA
44.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA).

A217929E01
0.467,0.856 2.887,1.519 2.420,0.663 10 Engine Coolant Temperature Increase after Engine Start (Engine Coolant Temperature - Engine Coolant Temperature at Engine Start) 3.423,0.037 3.718,0.234 0.295,0.198 10 (°C) 5.609,2.116 6.223,2.286 0.614,0.170 10 (Minutes) 5.16,1.69 5.316,1.846 0.156,0.156 10 A 4.964,0.779 5.120,0.935 0.156,0.156 10 C 3.891,0.493 4.047,0.649 0.156,0.156 10 B 3.563,2.39 5.573,2.546 2.010,0.156 10 Time Elapsed after Engine Start

Result
Freeze Frame Data Item for DTC P1605 Result Suspected Area Proceed to
Initial Engine Coolant Temp, Coolant Temp, Engine Run Time Range A
·

Engine coolant temperature sensor

·

Thermostat


A
Range B Engine coolant temperature B
Range C - C

HINT:

This step is not directly related to engine stall.




A

45.INSPECT THERMOSTAT

B

47.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

C

76.CHECK FUEL SYSTEM
45.INSPECT THERMOSTAT
HINT:

For the thermostat inspection, refer to the following procedures (See page Engine / Hybrid System>1GR-FE (COOLING)>THERMOSTAT>INSPECTION).


Result
Result Proceed to
Abnormal A
Normal B

HINT:

This step is not directly related to engine stall.



A

B

47.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
46.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA).

Result
Freeze Frame Data Item for DTC P1605 Result Suspected Area Proceed to
Coolant Temp 120°C or higher Engine coolant temperature sensor A
Coolant Temp, Ambient Temp for A/C Engine coolant temperature is lower than outside temperature by 15°C or more Engine coolant temperature sensor
Both freeze frame data items listed above Values are other than above - B



A

47.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

B

79.CLEAR DTC
47.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
HINT:

For the engine coolant temperature sensor inspection, refer to the following procedures (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>ENGINE COOLANT TEMPERATURE SENSOR>INSPECTION).


Result
Result Proceed to
Normal A
Abnormal B

HINT:
for Automatic Transmission

Perform "Inspection After Repair" after replacing the engine coolant temperature sensor (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).



A

48.CHECK HARNESS AND CONNECTOR (ECM - ENGINE COOLANT TEMPERATURE SENSOR)

B

48.CHECK HARNESS AND CONNECTOR (ECM - ENGINE COOLANT TEMPERATURE SENSOR)
a.

Check the harnesses and connectors, referring to DTC P0115 inspection procedure (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>P0115).


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

49.CHECK IGNITION SYSTEM
a.

Perform ignition system On-vehicle Inspection (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION).

HINT:
for Automatic Transmission

Perform "Inspection After Repair" after repairing or replacing the ignition system (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




OK

50.READ FREEZE FRAME DATA

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

50.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA).

Result
Freeze Frame Data Item for DTC P1605 Result Suspected Area Proceed to
Total of ISC Learning Value and ISC Feedback Value Below 80% of the current value of the vehicle Intake air volume insufficient A
80% or more of the current value of the vehicle B



A

51.CHECK INTAKE SYSTEM

B

53.PERFORM ACTIVE TEST USING GTS (CONTROL THE VVT LINEAR)
51.CHECK INTAKE SYSTEM
a.

Check for air leakage in the intake system [vacuum hose disconnection, cracks, damaged gaskets, etc.] (See page Engine / Hybrid System>1GR-FE (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION).

HINT:
·

If the accelerator pedal is released after racing the engine, the inspection is easier to perform because the vacuum inside the intake pipes increases and the air suction noise becomes louder.

·

If Short FT and Long FT are largely different from the normal values when idling (the intake air volume is small) and almost the same as the normal values when racing the engine (the intake air volume is high), air leakage may be present.



OK:

There is no air leakage.


HINT:
for Automatic Transmission

Perform "Inspection After Repair" after repairing or replacing the intake system (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




OK

52.CHECK INTAKE SYSTEM

NG

REPAIR OR REPLACE INTAKE SYSTEM

52.CHECK INTAKE SYSTEM
a.

Check the intake system.

·

Inspect the brake booster assembly.

·

Inspect the Mass air flow meter.

·

Check the PCV hose.

·

Inspect the PCV valve.

·

Inspect the purge VSV.


Result
Result Proceed to
Abnormal A
Normal B

HINT:
for Automatic Transmission

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




A

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

B

57.READ FREEZE FRAME DATA
53.PERFORM ACTIVE TEST USING GTS (CONTROL THE VVT LINEAR)
a.

Connect the GTS to the DLC3.


b.

Turn the GTS on.


c.

Warm up the engine.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Linear (Bank1) or Control the VVT Linear (Bank2).

HINT:

When performing the Active Test, make sure the A/C is on and the shift lever is in P or N.



e.

Check the engine speed while operating the camshaft timing oil control valve using the GTS.

OK:
GTS Operation Specified Condition
0% Normal engine speed
100% Engine idles roughly or stalls


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

When the results of the inspection using the Active Test are normal but the valve operating noise is abnormal, check the valve for any signs of problems.

·

If the camshaft timing oil control valve is stuck on, the valve overlap increases and combustion worsens due to the internal EGR which may cause rough idle or cause the engine to stall.





OK

54.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

54.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)
a.

Check the harnesses and connectors, referring to DTC P0010 inspection procedure (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>P0010).

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.





OK

55.PERFORM ACTIVE TEST USING GTS (CONTROL THE VVT EXHAUST LINEAR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

55.PERFORM ACTIVE TEST USING GTS (CONTROL THE VVT EXHAUST LINEAR)
a.

Connect the GTS to the DLC3.


b.

Turn the GTS on.


c.

Warm up the engine.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Exhaust Linear (Bank1) or Control the VVT Exhaust Linear (Bank2).

HINT:

When performing the Active Test, make sure the A/C is on and the shift lever is in P or N.



e.

Check the engine speed while operating the camshaft timing oil control valve using the GTS.

OK:
GTS Operation Specified Condition
0% Normal engine speed
100% Engine idles roughly or stalls


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

When the results of the inspection using the Active Test are normal but the valve operating noise is abnormal, check the valve for any signs of problems.

·

If the camshaft timing oil control valve is stuck on, the valve overlap increases and combustion worsens due to the internal EGR which may cause rough idle or cause the engine to stall.





OK

56.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

56.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)
a.

Check the harnesses and connectors, referring to DTC P0013 inspection procedure (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>P0013).

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.





OK

57.READ FREEZE FRAME DATA

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

57.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA).

Result
Freeze Frame Data Item for DTC P1605 Suspected Area Proceed to
IGN Advance Knock Correct Learn Value
Differs from the current value of the vehicle by 10° or more Less than 3°
·

Engine coolant temperature sensor

·

Mass air flow meter

·

Knock sensor


A
3° or more - B
Differs from the current value of the vehicle by less than 10° - -



A

58.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

B

58.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
HINT:
·

For the engine coolant temperature sensor inspection, refer to the following procedures (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>ENGINE COOLANT TEMPERATURE SENSOR>INSPECTION).


for Automatic Transmission
·

Perform "Inspection After Repair" after replacing the engine coolant temperature sensor (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




OK

59.CHECK HARNESS AND CONNECTOR (ECM - ENGINE COOLANT TEMPERATURE SENSOR)

NG

59.CHECK HARNESS AND CONNECTOR (ECM - ENGINE COOLANT TEMPERATURE SENSOR)
a.

Check the harnesses and connectors, referring to DTC P0115 inspection procedure (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>P0115).


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.




OK

60.INSPECT MASS AIR FLOW METER (INTAKE AIR TEMPERATURE SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

60.INSPECT MASS AIR FLOW METER (INTAKE AIR TEMPERATURE SENSOR)
a.

Inspect the mass air flow meter (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>MASS AIR FLOW METER>INSPECTION).

HINT:
·

If the intake air temperature sent to the ECM is higher than the standard due to the Mass air flow meter (intake air temperature sensor) malfunctioning, the ignition timing may become delayed.


for Automatic Transmission
·

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).





OK

61.READ VALUE USING GTS

NG

61.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Start the engine and warm it up until the engine coolant temperature stabilizes.

HINT:

The A/C switch and all accessory switches should be off.



c.

Idle the engine.


d.

Using the GTS, read the value of IGN Advance and Knock Correct Learn Value in the Data List.

Result
Freeze Frame Data Item for DTC P1605 Proceed to
IGN Advance Knock Correct Learn Value
Differs from the current value of the vehicle by 10° or more Less than 3° A
3° or more B
Differs from the current value of the vehicle by less than 10° -

HINT:

If the results of the checks performed in steps 56 to 64 were all normal and the sum of ISC Feedback Value and ISC Learning Value in the Data List is 120% of the normal value or more, check for carbon deposits in the throttle body assembly. If there are carbon deposits, clean them off to finish the troubleshooting procedure.




A

B

END

62.INSPECT TERMINAL VOLTAGE (FUEL INJECTOR POWER SOURCE)
a.

Check the harnesses and connectors, referring to DTC P0300 inspection procedure (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>P0300).


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.




OK

63.CHECK IGNITION SYSTEM

NG

63.CHECK IGNITION SYSTEM
a.

Perform ignition system On-vehicle Inspection (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION).

HINT:
for Automatic Transmission

Perform "Inspection After Repair" after repairing or replacing the ignition system (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




OK

64.CHECK FREEZE FRAME DATA

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

64.CHECK FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA).

Result
Freeze Frame Data Item for DTC P1605 Suspected Area Proceed to
A/C Signal Air Conditioner FB Val Power Steering Signal
A/C Signal display changes from OFF to ON*1 Value displayed for Air Conditioner FB Val increases - A/C system B
Value displayed for Air Conditioner FB Val does not increase Does not change from OFF - A*1
C*2
Changes from OFF to ON Power steering system
A/C Signal display does not change from OFF - Changes from OFF to ON
Does not change from OFF -

*1: for A/T

*2: for M/T


HINT:
·

*1: Check not only the on/off state of the air conditioner but also the change in air conditioner load.

·

The normal value for the ISC learned value is engine displacement (liters) x 0.9.

·

Even if the results are normal, the power steering system and/or A/C system may have been malfunctioning. If there are no problems with other parts, inspect the power steering system and/or A/C system.





A

65.CHECK FREEZE FRAME DATA

B

CHECK AIR CONDITIONING SYSTEM

C

67.CHECK FREEZE FRAME DATA
65.CHECK FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA).

Result
Freeze Frame Data Item for DTC P1605 Suspected Area Proceed to
Electrical Load Signal or Electric Load Feedback Val Electric Load Feedback Val Difference between Engine Speed and SPD (NT) Vehicle Speed
Electrical Load Signal display changes from OFF to ON*1, or value displayed for Electric Load Feedback Val increases*1 Value displayed for Electric Load Val changes - - Electrical load signal circuit C
Value displayed for Electric Load Val does not change At least 1 of the 5 sets of freeze frame data is less than 100 rpm Less than 30 km/h A/T system B
30 km/h or more - A
All 5 sets of freeze frame data are 100 rpm or more - - A
Electrical Load Signal display does not change from OFF, or value displayed for Electric Load Feedback Val does not increase - At least 1 of the 5 sets of freeze frame data is less than 100 rpm Less than 30 km/h A/T system B
30 km/h or more - A
All 5 sets of freeze frame data are 100 rpm or more - - A

HINT:
·

*1: If the Electrical Load Signal display changes from OFF to ON, or the "Electric Load Feedback Val" increases, it probably is a malfunction due to a change in electrical load. Check the generator and the continuity and connections between the generator and ECM.

·

The normal value for the ISC learned value is engine displacement (liters) x 0.9.

·

Even if the results are normal, the electrical load signal system and/or A/T system may have been malfunctioning. If there are no problems with other parts, inspect the electrical load system and/or A/T system.





A

66.CHECK FREEZE FRAME DATA

B

CHECK AUTOMATIC TRANSMISSION SYSTEM

C

66.CHECK FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA).

Result
Freeze Frame Data Item for DTC P1605 Suspected Area Proceed to
Shift SW Status (P Range)
Shift SW Status (N Range)
Neutral Position SW Signal
P and N position are both OFF in at least one data set In D or R, NSW is ON Park/neutral position switch assembly A
In D or R, NSW is OFF A/T system B
All 5 sets of freeze frame data are ON - - C

HINT:

Even if the results are normal, the park/neutral position switch assembly and/or A/T system may have been malfunctioning. If there are no problems with other parts, inspect the park/neutral position switch assembly and/or A/T system.




A

INSPECT PARK/NEUTRAL POSITION SWITCH

B

CHECK AUTOMATIC TRANSMISSION SYSTEM

C

67.CHECK FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA).

Result
Freeze Frame Data Item for DTC P1605 Proceed to
Electrical Load Signal or Electric Load Feedback Val Electric Load Feedback Val
Electrical Load Signal display changes from OFF to ON*1, or value displayed for Electric Load Feedback Val increases*1 Value displayed for Electric Load Val changes A
Value displayed for Electric Load Val does not change B
Electrical Load Signal display does not change from OFF, or value displayed for Electric Load Feedback Val does not increase -

HINT:
·

*1: If the Electrical Load Signal display changes from OFF to ON, or the "Electric Load Feedback Val" increases, it probably is a malfunction due to a change in electrical load. Check the generator and the continuity and connections between the generator and ECM.

·

The normal value for the ISC learned value is engine displacement (liters) x 0.9.

·

Even if the results are normal, the electrical load signal system may have been malfunctioning. If there are no problems with other parts, inspect the electrical load system.





A

B

68.CHECK FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA).

Result
Freeze Frame Data Item Result Suspected Area Proceed to
Throttle Sensor Position, Calculate Load Calculate Load decreases while Throttle Sensor Position increases Mass air flow meter A
Calculate Load does not decrease while Throttle Sensor Position increases - B



A

69.CHECK MASS AIR FLOW METER

B

72.INSPECT TERMINAL VOLTAGE (FUEL INJECTOR POWER SOURCE)
69.CHECK MASS AIR FLOW METER

b.

Check for foreign matter in the airflow passage of the mass airflow meter.

Result
Result Proceed to
Visible foreign matter is not present A
Visible foreign matter is present B

HINT:
for Automatic Transmission

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




A

70.CHECK HARNESS AND CONNECTOR (ECM - MASS AIR FLOW METER)

B

70.CHECK HARNESS AND CONNECTOR (ECM - MASS AIR FLOW METER)
a.

Check the harnesses and connectors, referring to DTC P0102 inspection procedure (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>P0102).

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.





OK

71.PERFORM DRIVE TEST

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

71.PERFORM DRIVE TEST
a.

Connect the GTS to the DLC3.


b.

Start the engine and warm it up until the engine coolant temperature stabilizes.

HINT:

The A/C switch and all accessory switches should be off.



c.

Idle the engine.


d.

Using the GTS, read the value of Calculate Load in the Data List.

Standard:
Data List Specified Condition
Calculate Load 90 to 110% of the current value of the vehicle


HINT:
for Automatic Transmission

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




OK

72.INSPECT TERMINAL VOLTAGE (FUEL INJECTOR POWER SOURCE)

NG

72.INSPECT TERMINAL VOLTAGE (FUEL INJECTOR POWER SOURCE)
a.

Check the harnesses and connectors, referring to DTC P0300 inspection procedure (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>P0300).


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.




OK

73.CHECK IGNITION SYSTEM

NG

73.CHECK IGNITION SYSTEM
a.

Perform ignition system On-vehicle Inspection (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION).

HINT:
for Automatic Transmission

Perform "Inspection After Repair" after repairing or replacing the ignition system (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




OK

74.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP / SPEED)

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

74.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP / SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.


e.

When performing the Active Test, check for an operating sound from the fuel pump.

Standard:
Control the Fuel Pump / Speed Specified Condition
ON Operating sound heard
OFF Operating sound not heard


Result
Result Proceed to
Abnormal A
Normal B

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

While performing the Active Test, make sure that there is no fuel leakage from the pipes, no signs that fuel has leaked, and no fuel smell.

·

If the fuel pump operating noise is abnormal, proceed to step 75.





A

75.INSPECT FUEL PUMP

B

76.CHECK FUEL SYSTEM
75.INSPECT FUEL PUMP
a.

Inspect the fuel pump (for Single Tank Type) (See page Engine / Hybrid System>1GR-FE (FUEL)>FUEL PUMP (for Single Tank Type)>INSPECTION).


b.

Inspect the fuel pump (for Double Tank Type) (See page Engine / Hybrid System>1GR-FE (FUEL)>FUEL PUMP (for Double Tank Type)>INSPECTION).

Result
Result Proceed to
OK A
NG (for Single Tank Type) B
NG (for Double Tank Type) C

HINT:
for Automatic Transmission

Perform "Inspection After Repair" after replacing the fuel pump (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




A

B

REPLACE FUEL PUMP (FOR SINGLE TANK TYPE)

C

REPLACE FUEL PUMP (FOR DOUBLE TANK TYPE)

76.CHECK FUEL SYSTEM
a.

Check the fuel system.

·

Check the fuel pump operation.

·

Check for fuel leaks.

·

Check the fuel pressure.

·

Perform the Active Test [Control the Select Cylinder Fuel Cut].



HINT:

For the fuel system On-vehicle Inspection, refer to the following procedures (See page Engine / Hybrid System>1GR-FE (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION).


Result
Result Proceed to
Abnormal A
Normal B


A

77.CHECK FUEL SYSTEM

B

77.CHECK FUEL SYSTEM
a.

Check for foreign matter such as iron particles around the fuel pump (fuel pump, fuel pump filter and inside the fuel tank), and for signs that the fuel pump was stuck.

Result
Result Proceed to
There is no foreign matter and no signs that fuel pump was stuck A
There is foreign matter or signs that fuel pump was stuck B

HINT:

If there is foreign matter such as iron particles on the fuel pump, fuel filter or fuel tank, remove the foreign matter.




A

78.CHECK FUEL SYSTEM

B

REPAIR OR REPLACE FUEL SYSTEM

78.CHECK FUEL SYSTEM
a.

Check the fuel system.

·

Check the fuel pump operation.

·

Check for fuel leaks.

·

Check the fuel pressure.

·

Perform the Active Test [Control the Select Cylinder Fuel Cut].



HINT:

For the fuel system On-vehicle Inspection, refer to the following procedures (See page Engine / Hybrid System>1GR-FE (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION).



OK

END

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

79.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.




NEXT

END