1.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
2.DISCHARGE FUEL SYSTEM PRESSURE
3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
53301
4.REMOVE HOOD SUB-ASSEMBLY
Disconnect the washer nozzle hose.
Remove the 8 bolts and hood.
If the hood support is detached from the ball joint, it become non-reusable. Therefore, do not detach the hood support from the ball joint unless replacing it.
55781E
5.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY
Remove the cowl top ventilator louver (See page Vehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>REMOVAL).
52129B
6.REMOVE FRONT BUMPER COVER LOWER
Remove the clip, 5 bolts and front bumper cover lower.
51405A
7.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
Remove the 4 bolts.
Unhook the engine under cover from the vehicle body as shown in the illustration.
51495
8.REMOVE TRANSMISSION UNDER COVER
Remove the 2 bolts and transmission under cover.
51450
9.REMOVE REAR ENGINE UNDER COVER ASSEMBLY
Remove the 4 bolts and rear engine under cover.
53737B
10.REMOVE FRONT FENDER APRON SEAL LH
Remove the 5 clips and front fender apron seal.
53736
11.REMOVE FRONT FENDER APRON SEAL RH
Remove the 5 clips and front fender apron seal.
53737A
12.REMOVE FRONT NO. 1 FENDER APRON TO FRAME SEAL LH
Remove the 5 clips and front No. 1 fender apron to frame seal.
53736B
13.REMOVE FRONT NO. 1 FENDER APRON TO FRAME SEAL RH
Remove the 5 clips and front No. 1 fender apron to frame seal.
53292A
14.REMOVE UPPER RADIATOR SUPPORT SEAL
Remove the 13 clips and upper radiator support seal.
15.DRAIN ENGINE OIL
16.DRAIN ENGINE COOLANT
28800A
17.DISCONNECT CABLE FROM POSITIVE BATTERY TERMINAL
74481
18.REMOVE BATTERY HOLD DOWN CLAMP
28800
19.REMOVE BATTERY
74431
20.REMOVE BATTERY TRAY
11259
21.REMOVE V-BANK COVER
52119A
22.REMOVE FRONT BUMPER COVER
Remove the front bumper cover (See page Vehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER>REMOVAL).
23.REMOVE AIR CLEANER CAP AND HOSE
24.REMOVE AIR CLEANER CASE SUB-ASSEMBLY
52521
25.REMOVE FRONT BUMPER CENTER UPPER RETAINER
53293C
26.REMOVE RADIATOR SIDE DEFLECTOR RH
53294C
27.REMOVE RADIATOR SIDE DEFLECTOR LH
16571C
28.REMOVE NO. 1 RADIATOR HOSE
16572D
29.REMOVE NO. 2 RADIATOR HOSE
16470
30.REMOVE RADIATOR RESERVOIR
32907C
31.DISCONNECT OIL COOLER TUBE (w/ Warmer)
32907C
32.DISCONNECT OIL COOLER TUBE (w/ Air Cooled Transmission Oil Cooler)
16711
33.REMOVE FAN SHROUD
16400
34.REMOVE RADIATOR ASSEMBLY
17360
35.REMOVE AIR TUBE ASSEMBLY (w/ Secondary Air Injection System)
17129
36.REMOVE INTAKE AIR SURGE TANK
37.REMOVE FAN AND GENERATOR V BELT
44320
38.DISCONNECT VANE PUMP ASSEMBLY
88711
39.DISCONNECT DISCHARGE HOSE SUB-ASSEMBLY
88704
40.DISCONNECT SUCTION HOSE SUB-ASSEMBLY
88320
41.REMOVE COOLER COMPRESSOR ASSEMBLY
17410
42.REMOVE FRONT EXHAUST PIPE ASSEMBLY
Remove the front exhaust pipe (See page Engine / Hybrid System>1GR-FE (INTAKE / EXHAUST)>EXHAUST PIPE>REMOVAL).
17118
43.REMOVE MANIFOLD STAY
17361
44.REMOVE AIR TUBE (w/ Secondary Air Injection System)
45203
45.DISCONNECT NO. 2 STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY (for RHD)
for Manual tilt and manual telescopic steering column:
Disconnect the No. 2 steering intermediate shaft (See page Steering>STEERING COLUMN>STEERING COLUMN ASSEMBLY (for Manual Tilt and Manual Telescopic Steering Column)>REMOVAL).
for Power tilt and power telescopic steering column:
Disconnect the No. 2 steering intermediate shaft (See page Steering>STEERING COLUMN>STEERING COLUMN ASSEMBLY (for Power Tilt and Power Telescopic Steering Column)>REMOVAL).
17167
46.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
17104
47.REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH
17119
48.REMOVE NO. 2 MANIFOLD STAY
17362
49.REMOVE NO. 2 AIR TUBE (w/ Secondary Air Injection System)
17168
50.REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR
17105
51.REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY LH
82715
52.REMOVE WIRING HARNESS CLAMP BRACKET
27020
53.REMOVE GENERATOR ASSEMBLY
28100
54.REMOVE STARTER ASSEMBLY
55.REMOVE DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT (for Automatic Transmission)
82121
56.DISCONNECT ENGINE WIRE
Remove the bolt and disconnect the connector.
Remove the glove compartment door (See page Vehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REMOVAL).
Disconnect the ECM connector.
Detach the clamp and disconnect the 9 connectors.
| *A | for LHD |
| *B | for RHD |
Detach the grommet from the wire harness support.
| *A | for LHD |
| *B | for RHD |
Detach the 4 claws to remove the wire harness support from the vehicle, and then pull out the ECM connector to remove it from the vehicle.
| *A | for LHD |
| *B | for RHD |
57.DISCONNECT HEATER WATER HOSE ASSEMBLY
w/o Rear heater:
Disconnect the 2 hoses and heater water hose.
| *A | w/o Rear Heater |
| *B | w/ Rear Heater |
w/ Rear heater:
Disconnect the 4 hoses and heater water hose.
23801P
58.DISCONNECT NO. 1 AND NO. 2 FUEL PIPES
Remove the No. 2 fuel pipe clamp from the fuel tube connector.
Disconnect the No. 1 and No. 2 fuel pipes (See page Engine / Hybrid System>1GR-FE (FUEL)>FUEL SYSTEM>PRECAUTION).
59.REMOVE FRONT PROPELLER SHAFT ASSEMBLY
60.REMOVE PROPELLER SHAFT ASSEMBLY
33030
61.REMOVE MANUAL TRANSMISSION ASSEMBLY (for Manual Transmission)
Remove the manual transmission from the vehicle (See page Drivetrain>RA61F (MANUAL TRANSMISSION / TRANSAXLE)>MANUAL TRANSMISSION ASSEMBLY (for 1GR-FE)>REMOVAL).
35000
62.REMOVE AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission)
Remove the automatic transmission from the vehicle (See page Drivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION ASSEMBLY (for 1GR-FE)>REMOVAL).
12371
63.REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR (for Automatic Transmission)
12371
64.REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR (for Manual Transmission)
88704
65.DISCONNECT SUCTION HOSE SUB-ASSEMBLY
Remove the bolt and disconnect the suction hose.
66.DISCONNECT OIL COOLER TUBE SUB-ASSEMBLY (for Automatic Transmission)
Remove the bolt and disconnect the oil cooler tube.
| *A | w/o Air Cooled Transmission Oil Cooler |
| *B | w/ Air Cooled Transmission Oil Cooler |
31210
67.REMOVE CLUTCH COVER ASSEMBLY (for Manual Transmission)
31250
68.REMOVE CLUTCH DISC ASSEMBLY (for Manual Transmission)
13405
69.REMOVE FLYWHEEL SUB-ASSEMBLY (for Manual Transmission)
Using SST, hold the crankshaft.
Remove the 8 bolts and flywheel.
Do not reuse the bolts.
32101
70.REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for Automatic Transmission)
Using SST, hold the crankshaft.
Remove the 8 bolts, rear spacer, drive plate and front spacer.
71.REMOVE ENGINE ASSEMBLY
Install 2 engine hangers with 4 bolts as shown in the illustration.
| *1 | No. 1 Engine Hanger |
| *2 | No. 2 Engine Hanger |
| No. 1 Engine Hanger | 12281-31110 |
| No. 2 Engine Hanger | 12282-31140 |
| Bolt | 91671-C0830 |
Attach an engine sling device and hang the engine with a chain block.
Remove the 6 nuts from the front engine mounting insulator LH and RH.
Lift the engine out of the vehicle carefully.
Make sure the engine is clear of all wiring and hoses.
Remove the front engine mounting insulator LH and RH.
Place the engine onto a work bench.
72.INSTALL ENGINE STAND
Install the engine onto an engine stand with bolts.