When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.
| Replaced Parts (A) | Pipes Requiring New Replacement |
|---|---|
| Injector assembly (including shuffling the injector assemblies between the cylinders) | ·
No. 1 injection pipe sub-assembly ·
No. 2 injection pipe sub-assembly |
| Supply pump assembly | Fuel inlet pipe sub-assembly |
·
Common rail assembly ·
Cylinder block sub-assembly ·
Cylinder head sub-assembly ·
Cylinder head gasket ·
Timing chain case assembly |
·
No. 1 injection pipe sub-assembly ·
No. 2 injection pipe sub-assembly ·
Fuel inlet pipe sub-assembly |
After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.
The injector assembly is a precision instrument. Do not use the injector assembly if it is struck or dropped.
The supply pump assembly is a precision instrument. Do not use the supply pump assembly if it is struck or dropped.
The common rail assembly is a precision instrument. Do not use the common rail assembly if it is struck or dropped.
Hold the supply pump assembly itself during removal and installation. Do not hold the pre-stroke control valve or fuel pipe, etc.
Hold the common rail assembly itself during removal and installation. Do not hold the pressure discharge valve or fuel pressure sensor, etc.
Make sure foreign matter does not enter the fuel path.
16575C
1.INSTALL NO. 1 WATER HOSE CLAMP BRACKET
Install the No. 1 water hose clamp bracket to the timing chain case assembly with the bolt.
13471
2.INSTALL CRANKSHAFT PULLEY
13496
3.INSTALL CRANKSHAFT PULLEY COVER
88451B
4.INSTALL VISCOUS HEATER CRANKSHAFT PULLEY (w/ Viscous Heater)
25709E
5.INSTALL NO. 4 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY
Install the No. 4 vacuum transmitting pipe sub-assembly to the cylinder block sub-assembly with the bolt.
25708
6.INSTALL NO. 3 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY
Install the No. 3 vacuum transmitting pipe sub-assembly to the cylinder head sub-assembly and cylinder block sub-assembly with the 2 bolts.
Connect the No. 4 vacuum transmitting hose sub-assembly to the No. 3 vacuum transmitting pipe sub-assembly.
25707
7.INSTALL NO. 2 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY
Install the No. 2 vacuum transmitting pipe sub-assembly to the cylinder block sub-assembly and oil pan sub-assembly with the 2 bolts.
25706
8.INSTALL NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY
Install the No. 1 vacuum transmitting pipe sub-assembly to the cylinder head sub-assembly and cylinder block sub-assembly with the 3 bolts.
Connect the No. 2 vacuum transmitting hose sub-assembly to the No. 3 vacuum transmitting pipe sub-assembly.
Connect the No. 1 vacuum transmitting hose sub-assembly to the vacuum pump assembly.
25804A
9.INSTALL VACUUM SWITCHING VALVE SUB-ASSEMBLY (for Engine Mounting)
16620
10.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY
16603
11.INSTALL NO. 1 IDLER PULLEY SUB-ASSEMBLY
16304
12.INSTALL WATER OUTLET SUB-ASSEMBLY
Install a new gasket and the water outlet sub-assembly to the timing chain cover sub-assembly with the 4 bolts and 2 nuts.
16207
13.INSTALL NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY
Install the No. 2 water by-pass pipe sub-assembly to the engine water pump assembly and water inlet with the 2 bolts.
Connect the No. 3 water by-pass hose to the water outlet sub-assembly, and slide the clamp to secure the hose.
15407
14.TEMPORARILY INSTALL TURBO OIL INLET PIPE SUB-ASSEMBLY
17141
15.TEMPORARILY INSTALL EXHAUST MANIFOLD WITH TURBOCHARGER SUB-ASSEMBLY
Install 2 new gaskets to the exhaust manifold and turbocharger sub-assembly.
Temporarily install the exhaust manifold to turbocharger sub-assembly with 3 new nuts.
Temporarily install the exhaust manifold with turbocharger sub-assembly, 8 collars and the 8 plate washers to the cylinder head sub-assembly with 8 new nuts.
| *1 | Collar |
|
Engine Side |
Make sure that the side of the collar with the smaller diameter faces the exhaust manifold.
Install a new gasket on the union bolt side to turbo oil inlet pipe sub-assembly.
Temporarily install the union bolt.
15474
16.INSTALL TURBO OIL OUTLET PIPE
17293
17.TEMPORARILY INSTALL TURBOCHARGER STAY
Temporarily install the turbocharger stay to the turbocharger sub-assembly, with 3 bolts and nut.
17141
18.TIGHTEN EXHAUST MANIFOLD WITH TURBOCHARGER SUB-ASSEMBLY
17293
19.TIGHTEN TURBOCHARGER STAY
87101
20.INSTALL NO. 1 VISCOUS HEATER BRACKET SUB-ASSEMBLY (w/ Viscous Heater)
Temporarily install the No. 1 viscous heater bracket sub-assembly to the cylinder block sub-assembly and timing chain cover sub-assembly with the 4 bolts.
Tighten the 4 bolts in the sequence shown in the illustration to install the No. 1 viscous heater bracket sub-assembly.
16284
21.CONNECT NO. 1 AND NO. 2 TURBO WATER HOSE
16268
22.INSTALL NO. 1 WATER BY-PASS PIPE
Install a new gasket and the No. 1 water by-pass pipe to the timing chain cover sub-assembly with the 3 bolts.
Make sure that the claw of the gasket faces the No. 1 water by-pass pipe.
16279
23.INSTALL NO. 3 WATER BY-PASS PIPE
12361
24.INSTALL FRONT ENGINE MOUNTING INSULATOR RH
Install the front engine mounting insulator RH to the front No. 1 engine mounting bracket RH with the nut.
Connect the No. 3 vacuum transmitting hose sub-assembly to the front No. 1 engine mounting bracket RH.
89463C
25.INSTALL NO. 1 NITROGEN OXIDES SENSOR (w/ Urea SCR System)
25051
26.INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
27.INSTALL NO. 2 EXHAUST PIPE SUPPORT STAY
89463C
28.CONNECT NO. 1 NITROGEN OXIDES SENSOR (w/ Urea SCR System)
17271
29.INSTALL NO. 1 TURBO INSULATOR
17167
30.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
89467B
31.INSTALL AIR FUEL RATIO SENSOR (w/o Urea SCR System)
17168
32.INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR
23295D
33.INSTALL NO. 1 INJECTOR HOLDER
16281
34.CONNECT NO. 4 WATER BY-PASS HOSE
Connect the No. 4 water by-pass hose to the No. 1 injector holder, and slide the clamp to secure the hose.
16282
35.INSTALL NO. 5 WATER BY-PASS HOSE
Attach the clamp and install the No. 5 water by-pass hose to the No. 1 water hose clamp bracket.
Connect the No. 5 water by-pass hose to the No. 1 injector holder and water outlet sub-assembly, and slide the 2 clamps to secure the hose.
36.INSTALL WATER BY-PASS HOSE (w/ Urea SCR System)
12229
37.INSTALL PCV PIPE (for Cold Area Specification Vehicles)
12261
38.INSTALL PCV HOSE (except Cold Area Specification Vehicles)
89422C
39.INSTALL ENGINE COOLANT TEMPERATURE SENSOR
88431
40.INSTALL NO. 1 COMPRESSOR MOUNTING BRACKET
Install the No. 1 compressor mounting bracket exactly as described in the procedures below to properly secure and prevent damage to the fan and generator V belt.
Temporarily install the No. 1 compressor mounting bracket to the cylinder block sub-assembly with the 2 bolts.
Temporarily install the No. 1 compressor mounting bracket with the 2 bolts so that the No. 1 compressor mounting bracket can be moved by hand.
Push the No. 1 compressor mounting bracket toward the cylinder block sub-assembly as shown in the illustration and tighten bolt A.
| *a | No Clearance |
| *b | Push |
| *c | Front |
Make sure there is no clearance between the cylinder block sub-assembly and No. 1 compressor mounting bracket as shown in the illustration.
Uniformly tighten the 3 bolts in the order shown in the illustration.
16025
41.INSTALL NO. 5 WATER BY-PASS PIPE SUB-ASSEMBLY
Install a new gasket and the No. 5 water by-pass pipe sub-assembly to the cylinder block sub-assembly with the 3 bolts.
Make sure that the claw of the gasket faces the No. 5 water by-pass pipe sub-assembly.
23300
42.INSTALL FUEL FILTER ASSEMBLY
Install the fuel filter assembly to the cylinder block sub-assembly with the 2 nuts.
23815D
43.INSTALL NO. 3 FUEL PIPE
44.INSTALL HOSE BRACKET
Install the hose bracket to the cylinder head sub-assembly with the 2 bolts.
19850
45.INSTALL GLOW PLUG ASSEMBLY
19871
46.INSTALL NO. 1 GLOW PLUG CONNECTOR
23810A
47.INSTALL COMMON RAIL ASSEMBLY
23701
48.TEMPORARILY INSTALL NO. 1 AND NO. 2 INJECTION PIPE SUB-ASSEMBLY
23670
49.TIGHTEN INJECTOR ASSEMBLY
23701
50.TIGHTEN NO. 1 AND NO. 2 INJECTION PIPE SUB-ASSEMBLY
51.INSTALL WIRING HARNESS CLAMP BRACKET
for LHD:
Install the 3 wiring harness clamp brackets to the cylinder head cover sub-assembly with the 3 bolts.
for RHD:
Install the 2 wiring harness clamp brackets to the cylinder head cover sub-assembly with the 2 bolts.
23811H
52.INSTALL NO. 1 FUEL PIPE
53.INSTALL WIRING HARNESS CLAMP BRACKET
17111
54.INSTALL INTAKE MANIFOLD
23770
55.INSTALL NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY
23804C
56.INSTALL FUEL INLET PIPE SUB-ASSEMBLY
23271H
57.INSTALL NO. 1 FUEL HOSE
23273H
58.INSTALL NO. 2 FUEL HOSE
23804D
59.INSTALL NO. 4 FUEL PIPE SUB-ASSEMBLY
23243B
60.INSTALL FUEL PUMP MOTOR WIRE
22803
61.INSTALL FUEL INJECTION PUMP COVER SUB-ASSEMBLY
17118
62.REMOVE MANIFOLD STAY
63.INSTALL WIRING HARNESS CLAMP BRACKET
23812D
64.INSTALL NO. 2 FUEL PIPE
Install the No. 2 fuel pipe to the manifold stay with the bolt.
Connect the No. 1 fuel hose to the No. 2 fuel pipe, and slide the clamp to secure the hose.
11409
65.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE
25800
66.INSTALL NO. 1 EGR COOLER AND NO. 2 EGR VALVE ASSEMBLY WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY
16209
67.INSTALL NO. 4 WATER BY-PASS PIPE SUB-ASSEMBLY
Install the No. 4 water by-pass pipe sub-assembly to the intake manifold with the 2 bolts.
for Cold Area Specification Vehicles:
Attach the clamp and connect the No. 11 water by-pass hose to the No. 2 fuel pipe.
Connect the water hose to the No. 2 EGR valve assembly, and slide the clamp to secure the hose.
Connect the No. 6 water by-pass hose to the No. 4 water by-pass pipe sub-assembly, and slide the clamp to secure the hose.
w/ Urea SCR System:
Install the No. 17 water by-pass hose to the No. 1 EGR pipe sub-assembly and No. 4 water by-pass pipe sub-assembly, and slide the 2 clamps to secure the hose.
25804
68.INSTALL VACUUM CONTROL VALVE SET
25601
69.INSTALL NO. 1 EGR PIPE SUB-ASSEMBLY
Using an E8 "TORX" socket wrench, install 2 new stud bolts to the exhaust manifold.
Install 2 new gaskets and the No. 1 EGR pipe sub-assembly to the exhaust manifold, electric EGR control valve assembly and No. 1 vacuum transmitting pipe sub-assembly with the bolt and 4 new nuts.
27148A
70.INSTALL CONNECTING WIRE
Attach the 2 clamps and install the connecting wire to the hose bracket.
Connect the connector to the common rail assembly.
16206B
71.INSTALL NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY
25612
72.INSTALL NO. 2 EGR PIPE
25625
73.INSTALL EGR VALVE BRACKET
89421C
74.INSTALL DIESEL TURBO PRESSURE SENSOR
23265C
75.INSTALL GAS FILTER
12631A
76.INSTALL ENGINE COVER BRACKET
17578B
77.INSTALL PIPE CLAMP
25734
78.TEMPORARILY INSTALL NO. 2 VACUUM PIPE
25733A
79.TEMPORARILY INSTALL NO. 1 VACUUM PIPE
25734
80.TIGHTEN NO. 2 VACUUM PIPE
25733A
81.TIGHTEN NO. 1 VACUUM PIPE
89425
82.INSTALL EXHAUST GAS TEMPERATURE SENSOR
89481B
83.INSTALL DIFFERENTIAL PRESSURE SENSOR
16278
84.INSTALL NO. 2 WATER BY-PASS PIPE
26100G
85.INSTALL DIESEL THROTTLE BODY ASSEMBLY
77246C
86.INSTALL FUEL MAIN TUBE SUPPORT (w/ Urea SCR System)
17360A
87.INSTALL AIR TUBE ASSEMBLY (w/o Urea SCR System)
82121
88.INSTALL ENGINE WIRE
12632
89.INSTALL NO. 2 ENGINE COVER BRACKET (w/o Urea SCR System)
12633
90.INSTALL NO. 3 ENGINE COVER BRACKET (w/o Urea SCR System)