Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function) › from 2020.08
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0261052 ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  Engine does not Start  


DESCRIPTION

When the electrical key transmitter sub-assembly is in the cabin and the engine switch is pressed, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode. Additionally, when the shift lever in P*1 and the brake pedal*1 or clutch pedal*2 is depressed, the engine can be started by pressing the engine switch. If the steering is unlocked, the engine can also be started by pressing the engine switch with the shift lever in P*1 and the brake pedal*1 or clutch pedal*2 depressed.

*1: for Automatic Transmission

*2: for Manual Transmission


Related Data List and Active Test Items
Problem Symptom Data List and Active Test
Engine does not Start
Power Source Control
·

Stop Light Switch1

·

Steering Unlock Switch

·

Shift P Signal*

·

IG Relay Monitor (Inside)

·

IG Relay Monitor (Outside)

·

Latch Circuit

·

Starter Request Signal

·

Power Supply Condition

·

Neutral SW/ Clutch SW


Entry&Start
·

Immobiliser

·

Engine Start Request

·

S Code Check

·

L Code Check


Starting Control
·

Starter SW

·

Shift Position Status*

·

Ignition



*: for Automatic Transmission


WIRING DIAGRAM

w/ Stop and Start System:


B598263E01
5.052,2.281 5.51,2.479 0.458,0.198 10 false STA 5.052,0.646 5.51,0.844 0.458,0.198 10 false STAR 5.042,1.344 5.5,1.542 0.458,0.198 10 false STP1 5.5,3.125 5.958,3.323 0.458,0.198 10 false P 5.729,2.927 6.188,3.125 0.458,0.198 10 false 22 4.75,1.146 5.208,1.344 0.458,0.198 10 false 2 4.729,0.448 5.188,0.646 0.458,0.198 10 false 10 4.729,2.104 5.188,2.302 0.458,0.198 10 false 12 0.542,1.875 1,2.073 0.458,0.198 10 false STA 0.479,0.646 0.938,0.844 0.458,0.198 10 false NSW 0.573,1.219 1.031,1.417 0.458,0.198 10 false STP 0.302,2.427 0.76,2.625 0.458,0.198 10 false ECM 6.583,3.135 7.042,3.333 0.458,0.198 10 false P2 6.594,5.135 7.052,5.333 0.458,0.198 10 false STP 6.198,7.042 6.656,7.24 0.458,0.198 10 false STP2 4.896,8.552 5.354,8.75 0.458,0.198 10 false STOP 3,3.5 3.458,3.698 0.458,0.198 10 false B 3.385,3.5 3.844,3.698 0.458,0.198 10 false L 2.635,3.76 3.094,3.958 0.458,0.198 10 false P 2.625,4.042 3.083,4.24 0.458,0.198 10 false N 0.49,4.031 0.948,4.229 0.458,0.198 10 false STA2 0.563,3.052 1.021,3.25 0.458,0.198 10 false CLL 2.115,4.438 3.438,5.604 1.323,1.167 10 false Park/Neutral Position Switch Assembly 0.094,5.5 2.177,6.135 2.083,0.635 10 false Engine Stop and Start ECU 0.688,5.958 2.771,6.594 2.083,0.635 10 false from Battery 1,7.99 3.698,8.313 2.698,0.323 10 false Starter Relay Assembly (ST Relay) 0.333,6.688 1.625,7.021 1.292,0.333 10 false ST NO.2 0.99,9.542 2.281,9.833 1.292,0.292 10 false Starter Assembly 1.073,8.885 1.531,9.083 0.458,0.198 10 false B 2.177,9.313 2.635,9.51 0.458,0.198 10 false SL1 2.188,8.917 2.646,9.115 0.458,0.198 10 false SL2 4.948,5.667 7.104,6.625 2.156,0.958 10 false Transmission Floor Shift Assembly (Shift Lock Control ECU) 4.542,3.594 6.406,4.333 1.865,0.74 10 false Certification ECU (Smart Key ECU Assembly) 5.073,9.563 7.115,9.875 2.042,0.313 10 false Stop Light Switch Assembly 5.885,9.208 6.344,9.406 0.458,0.198 10 false IC 5.948,8.396 7.115,9.198 1.167,0.802 10 false from Battery 5.5,8.917 5.958,9.115 0.458,0.198 10 false B 5.49,9.219 6.292,9.427 0.802,0.208 10 false L 6.208,9.208 6.667,9.406 0.458,0.198 10 false GND 4.656,0.656 5.115,0.854 0.458,0.198 10 false G213 4.646,1.333 5.104,1.531 0.458,0.198 10 false G213 5.677,3.125 6.135,3.323 0.458,0.198 10 false G215 0.969,1.667 1.427,1.865 0.458,0.198 10 false 22 0.979,0.448 1.438,0.646 0.458,0.198 10 false 11 0.99,1.146 1.448,1.344 0.458,0.198 10 false 13 3.198,3.229 3.656,3.427 0.458,0.198 10 false 4 2.135,4.271 2.594,4.469 0.458,0.198 10 false C159 0.104,5.344 0.563,5.542 0.458,0.198 10 false G313 0.906,2.917 1.365,3.115 0.458,0.198 10 false 17 0.969,3.948 1.427,4.146 0.458,0.198 10 false 23 5.094,9.438 5.552,9.635 0.458,0.198 10 false A99 1.052,7.656 1.51,7.854 0.458,0.198 10 false 1 1.719,7.656 2.177,7.854 0.458,0.198 10 false 2 1.729,7.365 2.188,7.563 0.458,0.198 10 false 3 1.073,7.396 1.531,7.594 0.458,0.198 10 false 5 0.76,8.688 1.219,8.885 0.458,0.198 10 false 1 2.604,8.708 2.854,9.198 0.25,0.49 10 false 2 2.604,9.135 3.063,9.333 0.458,0.198 10 false 1 0.677,8.896 1.135,9.094 0.458,0.198 10 false D13 2.51,9.333 2.969,9.531 0.458,0.198 10 false D14 5.323,9.208 5.781,9.406 0.458,0.198 10 false 3 5.281,8.823 5.74,9.021 0.458,0.198 10 false 7 6.594,9.115 7.052,9.313 0.458,0.198 10 false 2 6.271,2.948 6.729,3.146 0.458,0.198 10 false 11 6.292,4.938 6.75,5.135 0.458,0.198 10 false 6 5.5,7.365 5.958,7.563 0.458,0.198 10 false A7 5.938,6.938 6.396,7.135 0.458,0.198 10 false 45 5.49,7.531 7.073,8.292 1.583,0.76 10 false Brake Actuator Assembly (Skid Control ECU) 6.219,5.156 6.677,5.354 0.458,0.198 10 false G45 0.521,7.635 1.813,7.969 1.292,0.333 10 false ST 1.01,7.052 3.917,7.427 2.906,0.375 10 false Starter Relay Assembly (ST NO. 2 Relay) 1.042,6.438 1.5,6.635 0.458,0.198 10 false 5 1.729,6.438 2.188,6.635 0.458,0.198 10 false 3 1.042,6.698 1.5,6.896 0.458,0.198 10 false 1 1.729,6.688 2.188,6.885 0.458,0.198 10 false 2 0.552,4.969 1.01,5.167 0.458,0.198 10 false STA 0.927,4.854 1.385,5.052 0.458,0.198 10 false 21 3.708,3.938 4.167,4.135 0.458,0.198 10 false 5 0.906,0.656 2.146,0.875 1.24,0.219 10 false G184 4.656,2.292 5.115,2.49 0.458,0.198 10 false G213 0.906,1.323 2.146,1.542 1.24,0.219 10 false G184 0.896,1.865 2.135,2.083 1.24,0.219 10 false G184 6.219,3.125 6.677,3.323 0.458,0.198 10 false G45 2.521,8.917 2.979,9.115 0.458,0.198 10 false D14 5.5,1.844 5.958,2.042 0.458,0.198 10 false E 5.677,1.854 6.135,2.052 0.458,0.198 10 false G215 5.75,1.656 6.208,1.854 0.458,0.198 10 false 11


w/o Stop and Start System:


for Automatic Transmission:
B598261E02
0.219,4.052 0.677,4.25 0.458,0.198 10 false ECM 6.063,5.542 7.146,6.469 1.083,0.927 10 false Certification ECU (Smart Key ECU Assembly) 3.292,6.854 5.49,7.219 2.198,0.365 10 false Stater Relay Assembly (ST Relay) 0.104,5.615 3.917,5.813 3.813,0.198 10 false Transmission Floor Shift Assembly (Shift Lock Control ECU) 2.802,7.927 5,8.292 2.198,0.365 10 false Starter Assembly 2.698,3.698 4.021,4.115 1.323,0.417 10 false Park/Neutral Position Switch 1.583,8.885 3.781,9.25 2.198,0.365 10 false Stop Light Switch Assembly 1.031,8.583 1.542,8.823 0.51,0.24 10 false STOP 0.635,8.01 1.875,8.375 1.24,0.365 10 false from Battery 0.74,6.333 1.979,6.698 1.24,0.365 10 false from Battery 2.167,6.833 2.677,7.073 0.51,0.24 10 false ST 6.167,7.208 7.156,7.719 0.99,0.51 10 false Brake Actuator Assembly (Skid Control ECU) 6.667,0.333 7.125,0.531 0.458,0.198 10 false STA 6.26,0.333 6.719,0.531 0.458,0.198 10 false G213 6.333,0.135 6.792,0.333 0.458,0.198 10 false 12 6.656,1.417 7.115,1.615 0.458,0.198 10 false STAR 6.25,1.396 6.708,1.594 0.458,0.198 10 false G213 6.344,1.219 6.802,1.417 0.458,0.198 10 false 10 6.667,2.135 7.125,2.333 0.458,0.198 10 false STP1 6.25,2.135 6.708,2.333 0.458,0.198 10 false G213 6.365,1.958 6.823,2.156 0.458,0.198 10 false 2 6.26,4.479 6.719,4.677 0.458,0.198 10 false G215 2.583,2.75 3.042,2.948 0.458,0.198 10 false L 6.333,4.271 6.792,4.469 0.458,0.198 10 false 22 6.25,5.042 6.708,5.24 0.458,0.198 10 false G215 6.333,4.854 6.792,5.052 0.458,0.198 10 false 11 6.677,5.042 7.135,5.24 0.458,0.198 10 false E 0.385,0.323 0.844,0.521 0.458,0.198 10 false STA 0.75,0.333 1.208,0.531 0.458,0.198 10 false G56 1.146,0.333 1.604,0.531 0.458,0.198 10 false C154 0.813,0.146 1.271,0.344 0.458,0.198 10 false 28 1.229,0.135 1.688,0.333 0.458,0.198 10 false 17 1.521,0.333 1.979,0.531 0.458,0.198 10 false G184 1.615,0.125 2.073,0.323 0.458,0.198 10 false 22 0.323,1.396 0.781,1.594 0.458,0.198 10 false NSW 0.771,1.417 1.229,1.615 0.458,0.198 10 false C34 1.135,1.417 1.594,1.615 0.458,0.198 10 false C154 1.219,1.208 1.677,1.406 0.458,0.198 10 false 15 0.813,1.208 1.271,1.406 0.458,0.198 10 false 23 1.604,1.208 2.063,1.406 0.458,0.198 10 false 11 0.76,2.135 1.219,2.333 0.458,0.198 10 false G56 0.385,2.156 0.844,2.354 0.458,0.198 10 false STP 0.823,1.948 1.281,2.146 0.458,0.198 10 false 35 1.115,2.135 1.573,2.333 0.458,0.198 10 false G180 1.198,1.948 1.656,2.146 0.458,0.198 10 false 10 1.521,2.135 1.979,2.333 0.458,0.198 10 false G185 1.604,1.948 2.063,2.146 0.458,0.198 10 false 13 0.375,5.281 0.833,5.479 0.458,0.198 10 false STP 0.76,5.302 1.219,5.5 0.458,0.198 10 false G45 2.865,2.74 3.323,2.938 0.458,0.198 10 false B 6.677,4.5 7.135,4.698 0.458,0.198 10 false P 3.135,3.021 3.594,3.219 0.458,0.198 10 false P 3.125,3.313 3.583,3.51 0.458,0.198 10 false N 0.448,4.469 0.906,4.667 0.458,0.198 10 false P2 0.813,4.281 1.271,4.479 0.458,0.198 10 false 11 0.771,4.479 1.229,4.677 0.458,0.198 10 false G45 6.385,6.729 6.844,6.927 0.458,0.198 10 false A7 0.854,5.104 1.313,5.302 0.458,0.198 10 false 6 2.688,3.552 3.146,3.75 0.458,0.198 10 false C159 2.99,2.479 3.448,2.677 0.458,0.198 10 false 4 2.458,3.552 2.917,3.75 0.458,0.198 10 false 5 6,6.729 6.458,6.927 0.458,0.198 10 false A6 6.365,6.5 6.823,6.698 0.458,0.198 10 false 45 6.031,6.49 6.49,6.688 0.458,0.198 10 false 22 6.698,6.75 7.156,6.948 0.458,0.198 10 false STP2 1.615,8.427 2.125,8.667 0.51,0.24 10 false B 1.917,8.438 2.427,8.677 0.51,0.24 10 false L 3.354,6.542 3.865,6.781 0.51,0.24 10 false 5 4.01,6.542 4.521,6.781 0.51,0.24 10 false 3 4.01,6.083 4.521,6.323 0.51,0.24 10 false 2 3.313,6.073 3.823,6.313 0.51,0.24 10 false 1 3.698,7.417 4.208,7.656 0.51,0.24 10 false D12 3.76,7.219 4.271,7.458 0.51,0.24 10 false 1 4.031,7.427 4.542,7.667 0.51,0.24 10 false C158 4.156,7.229 4.667,7.469 0.51,0.24 10 false 1 4.521,7.229 5.031,7.469 0.51,0.24 10 false 1 4.448,7.427 4.958,7.667 0.51,0.24 10 false D10 4.854,7.427 5.365,7.667 0.51,0.24 10 false D11 4.906,7.24 5.417,7.479 0.51,0.24 10 false 1 2.469,7.26 2.979,7.5 0.51,0.24 10 false D1 2.094,7.26 2.604,7.5 0.51,0.24 10 false D4 1.688,7.281 2.198,7.521 0.51,0.24 10 false D8 1.302,7.271 1.813,7.51 0.51,0.24 10 false D9 1.354,7.073 1.865,7.313 0.51,0.24 10 false 1 1.74,7.073 2.25,7.313 0.51,0.24 10 false 1 2.146,7.073 2.656,7.313 0.51,0.24 10 false 1 2.51,7.083 3.021,7.323 0.51,0.24 10 false 1 3.375,7.438 3.885,7.677 0.51,0.24 10 false ST 2.823,7.313 3.281,7.51 0.458,0.198 10 false B 1.448,8.333 1.958,8.573 0.51,0.24 10 false 7 2.115,8.313 2.625,8.552 0.51,0.24 10 false 3 0.063,9.26 1.052,9.458 0.99,0.198 10 false *1: for 1GR-FE 0.052,9.573 1.042,9.771 0.99,0.198 10 false *2: for 2TR-FE 1.177,9.26 2.24,9.458 1.063,0.198 10 false *3: for 1GD-FTV 1.167,9.573 3.219,9.844 2.052,0.271 10 false *4: for Vacuum Brake Booster 3.313,9.563 4.635,9.781 1.323,0.219 10 false *6: except Cold Area 3.313,9.25 4.635,9.469 1.323,0.219 10 false *5: for Cold Area 0.813,0.552 1.271,0.75 0.458,0.198 10 false *1 1.229,0.552 1.688,0.75 0.458,0.198 10 false *2 0.823,1.635 1.281,1.833 0.458,0.198 10 false *1 1.229,1.625 1.688,1.823 0.458,0.198 10 false *2 1.594,1.635 2.052,1.833 0.458,0.198 10 false *3 0.813,2.365 1.271,2.563 0.458,0.198 10 false *1 1.198,2.365 1.656,2.563 0.458,0.198 10 false *2 1.583,2.365 2.042,2.563 0.458,0.198 10 false *3 1.573,8.729 2.031,8.927 0.458,0.198 10 false A99 2.49,7.49 2.948,7.688 0.458,0.198 10 false *1 2.094,7.49 2.552,7.688 0.458,0.198 10 false *2 1.594,7.479 2.052,7.677 0.458,0.198 10 false *3, *6 1.167,7.49 1.625,7.688 0.458,0.198 10 false *3, *5 3.708,7.646 4.167,7.844 0.458,0.198 10 false *1 4.104,7.635 4.563,7.833 0.458,0.198 10 false *2 4.375,7.635 4.833,7.833 0.458,0.198 10 false *3, *5 4.813,7.635 5.271,7.833 0.458,0.198 10 false *3, *6 5.979,6.938 6.438,7.135 0.458,0.198 10 false *4 6.354,6.927 6.813,7.125 0.458,0.198 10 false *7 5.052,9.542 7.156,9.792 2.104,0.25 10 false *7: for Hydraulic Brake Booster 1.604,0.563 2.063,0.76 0.458,0.198 10 false *3 1.51,1.417 1.969,1.615 0.458,0.198 10 false G184

for Manual Transmission:
B598262E01
0.229,4.302 0.688,4.5 0.458,0.198 10 false ECM 6.031,2.979 7.094,3.646 1.063,0.667 10 false Certification ECU (Smart Key ECU Assembly) 3.458,2.333 5.365,2.583 1.906,0.25 10 false Clutch Start Switch Assembly 0.75,0.552 1.208,0.75 0.458,0.198 10 false G56 0.771,0.365 1.229,0.563 0.458,0.198 10 false 10 1.094,0.552 1.552,0.75 0.458,0.198 10 false C154 1.198,0.354 1.656,0.552 0.458,0.198 10 false 17 1.5,0.542 1.958,0.74 0.458,0.198 10 false G184 1.573,0.354 2.031,0.552 0.458,0.198 10 false 22 6.083,0.552 6.542,0.75 0.458,0.198 10 false G213 6.156,0.354 6.615,0.552 0.458,0.198 10 false 12 6.094,1.823 6.552,2.021 0.458,0.198 10 false G213 6.177,1.635 6.635,1.833 0.458,0.198 10 false 10 6.083,2.49 6.542,2.688 0.458,0.198 10 false G215 6.208,2.292 6.667,2.49 0.458,0.198 10 false 11 1.271,6.021 1.729,6.219 0.458,0.198 10 false D9 1.667,6.031 2.125,6.229 0.458,0.198 10 false D8 2.042,6.01 2.51,6.219 0.469,0.208 10 false D4 2.438,6.021 2.896,6.219 0.458,0.198 10 false D1 3.656,6.177 4.115,6.375 0.458,0.198 10 false D12 4,6.188 4.458,6.385 0.458,0.198 10 false C158 4.438,6.188 4.896,6.385 0.458,0.198 10 false D10 4.833,6.177 5.292,6.375 0.458,0.198 10 false D11 4.927,5.99 5.385,6.188 0.458,0.198 10 false 1 4.531,6 4.99,6.198 0.458,0.198 10 false 1 4.135,6 4.594,6.198 0.458,0.198 10 false 1 3.729,6 4.188,6.198 0.458,0.198 10 false 1 2.49,5.802 2.948,6 0.458,0.198 10 false 1 2.104,5.823 2.563,6.021 0.458,0.198 10 false 1 1.698,5.813 2.156,6.01 0.458,0.198 10 false 1 1.323,5.813 1.781,6.01 0.458,0.198 10 false 1 2.792,6.042 3.25,6.24 0.458,0.198 10 false B 3.354,6.188 3.813,6.385 0.458,0.198 10 false ST 2.135,5.51 4.646,5.74 2.51,0.229 10 false Starter Relay Assembly (ST Relay) 0.646,4.99 1.604,5.281 0.958,0.292 10 false from Battery 0.823,5.438 1.781,5.729 0.958,0.292 10 false ST 2,4.698 2.958,4.99 0.958,0.292 10 false 1 2.01,5.198 2.969,5.49 0.958,0.292 10 false 5 2.698,4.729 3.656,5.021 0.958,0.292 10 false 2 2.719,5.198 3.677,5.49 0.958,0.292 10 false 3 0.333,0.552 1.292,0.844 0.958,0.292 10 false STA 6.479,0.552 7.156,0.979 0.677,0.427 10 false STA 6.479,1.844 7.156,2.271 0.677,0.427 10 false STAR 6.479,2.5 7.156,2.927 0.677,0.427 10 false E 3.5,2.125 4.396,2.375 0.896,0.25 10 false A40*1, r1*2 5,1.708 5.958,2 0.958,0.292 10 false 2 3.667,1.74 4.625,2.031 0.958,0.292 10 false 1 0.948,7.135 3.01,7.396 2.063,0.26 10 false *3: for 1GR-FE 2.771,6.677 5.281,6.906 2.51,0.229 10 false Starter Assembly 0.938,7.51 3,7.771 2.063,0.26 10 false *4: for 2TR-FE 2.198,7.146 4.26,7.406 2.063,0.26 10 false *5: for 1GD-FTV 0.021,7.125 2.083,7.385 2.063,0.26 10 false *1: for LHD 0.021,7.531 2.083,7.792 2.063,0.26 10 false *2: for RHD 3.458,7.146 5.521,7.406 2.063,0.26 10 false *7: except Cold Area 2.188,7.5 4.25,7.76 2.063,0.26 10 false *6: for Cold Area 0.771,0.792 2.833,1.052 2.063,0.26 10 false *3 1.156,0.792 3.219,1.052 2.063,0.26 10 false *4 1.594,0.792 3.656,1.052 2.063,0.26 10 false *5 2.458,6.229 4.521,6.49 2.063,0.26 10 false *3 2.052,6.229 4.115,6.49 2.063,0.26 10 false *4 1.135,6.25 3.198,6.51 2.063,0.26 10 false *5, *6 1.563,6.24 3.625,6.5 2.063,0.26 10 false *5, *7 3.688,6.396 5.75,6.656 2.063,0.26 10 false *3 4.094,6.396 6.156,6.656 2.063,0.26 10 false *4 4.354,6.406 6.417,6.667 2.063,0.26 10 false *5, *6 4.771,6.406 6.74,6.729 1.969,0.323 10 false *5, *7


CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

If the entry and start system (for Start Function) has been canceled, enable the system before performing troubleshooting.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>CUSTOMIZE PARAMETERS

·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

Before replacing the certification ECU (smart key ECU assembly) or an electrical key transmitter sub-assembly, refer to the Service Bulletin.

·

After completing repairs, confirm that the problem does not recur.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

·

When disconnecting and reconnecting the battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.CHECK ENGINE SWITCH CONDITION
a.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


b.

for Automatic Transmission:

Shift lever in P.


c.

With the brake pedal*1 or clutch pedal*2 released, check that pressing the engine switch causes the power source mode to change.

*1: for Automatic Transmission

*2: for Manual Transmission



Result:
Result Proceed to
Power source mode changes : Off → on (ACC) → on (IG) → off A
Power source mode does not change to on (ACC) or on (IG) B
Power source mode changes to on (IG) but not to on (ACC) C
Power source mode changes to on (ACC) but not to on (IG) D



A

2.CHECK VEHICLE CONDITION

B

GO TO ENTRY AND START SYSTEM (for Start Function) (Power Source Mode does not Change to ON (IG and ACC))

C

GO TO ENTRY AND START SYSTEM (for Start Function) (Power Source Mode does not Change to ON (ACC))

D

GO TO ENTRY AND START SYSTEM (for Start Function) (Power Source Mode does not Change to ON (IG))

2.CHECK VEHICLE CONDITION
a.

Check vehicle condition.


Result:
Proceed to
for Manual Transmission
for Automatic Transmission



for Manual Transmission

3.READ VALUE USING GTS (Neutral SW/ Clutch SW)

for Automatic Transmission

11.READ VALUE USING GTS (STOP LIGHT SWITCH1)
3.READ VALUE USING GTS (Neutral SW/ Clutch SW)
a.

Enter the following menus: Body Electrical / Power Source Control / Data List.


b.

Read the Data List according to the display on the GTS.

Power Source Control
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Neutral SW/ Clutch SW State of clutch pedal ON or OFF ON: Clutch pedal depressed
OFF: Clutch pedal released
·

Use this item to help determine if the clutch position switch is malfunctioning.

·

The engine cannot be started when this item is "OFF".



OK:

The GTS display changes correctly in response to the shift state.



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (STARTER REQUEST SIGNAL)

NG

7.READ VALUE USING GTS (Neutral SW/ Clutch SW)
4.READ VALUE USING GTS (STARTER REQUEST SIGNAL)
a.

Enter the following menus: Body Electrical / Power Source Control / Data List.


b.

Read the Data List according to the display on the GTS.

Power Source Control
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Starter Request Signal Engine start request signal status OFF or ON OFF: The engine switch is not pressed
ON: With the clutch pedal depressed, the engine switch is pressed and held
·

When the engine cannot be started due to a start request signal malfunction, OFF is displayed.

·

When the engine switch is pressed, the duration of time that ON is displayed will be extremely short. As such, the engine switch needs to be pressed and held for a certain period of time.



NOTICE:

Check that the key indicator display is displayed in the combination meter assembly, and then press the engine switch.


OK:

The GTS display changes correctly in response to the engine switch operation.



Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS (STARTER SW)

NG

34.CHECK STEERING LOCK
5.READ VALUE USING GTS (STARTER SW)
a.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


b.

Enter the following menus: Body Electrical / Starting Control / Data List.


c.

Read the Data List while pressing the engine switch with the clutch pedal depressed according to the display on the GTS.

Starting Control
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Starter SW Starter operation request OFF or ON OFF: Starter operation not requested
ON: Starter operation requested
When OFF is displayed, the engine will not crank.

OK:

The GTS display changes.



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST RELAY)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

6.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST RELAY)
a.

except 1GD-FTV:

i.
C378519C03
0.156,0.125 0.521,0.469 0.365,0.344 10 false *a
*a Engine Room Relay Block
(Starter Relay Assembly (ST Relay) Installation Terminal)


Remove the starter relay assembly (ST relay).


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Starter relay assembly (ST relay) installation terminal 2 - Body ground Engine switch pressed and held with clutch pedal depressed (starter on) → Approximately 1 second after engine switch released (starter off) 6 V or higher* → 1.0 V or less


HINT:

*: While the engine is cranking, the battery voltage may drop to approximately 6 V.




b.

for 1GD-FTV:

i.
C421133C01
0.156,0.125 0.521,0.469 0.365,0.344 10 false *a
*a Engine Room Relay Block
(Starter Relay Assembly (ST Relay) Installation Terminal)


Remove the starter relay assembly (ST relay).


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Starter relay assembly (ST relay) installation terminal 2 - Body ground Engine switch pressed and held with clutch pedal depressed (starter on) → Approximately 1 second after engine switch released (starter off) 6 V or higher* → 1.0 V or less


HINT:

*: While the engine is cranking, the battery voltage may drop to approximately 6 V.




Result:
Proceed to
OK
NG



OK

26.CHECK HARNESS AND CONNECTOR (ST RELAY - POWER SUPPLY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.READ VALUE USING GTS (Neutral SW/ Clutch SW)
a.

Disconnect the G56*1, C154*2 and G184*3 ECM connector.

·

*1: for 1GR-FE

·

*2: for 2TR-FE

·

*3: for 1GD-FTV



b.

Enter the following menus: Body Electrical / Power Source Control / Data List.


c.

Read the Data List according to the display on the GTS.

Power Source Control
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Neutral SW/ Clutch SW State of clutch pedal ON or OFF ON: Clutch pedal depressed
OFF: Clutch pedal released
·

Use this item to help determine if the clutch position switch is malfunctioning.

·

The engine cannot be started when this item is "OFF".



OK:

The GTS display changes correctly in response to the shift state.



Result:
Proceed to
OK
NG



OK

NG

8.INSPECT CLUTCH START SWITCH ASSEMBLY
8.INSPECT CLUTCH START SWITCH ASSEMBLY
a.

Remove the clutch start switch assembly.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>REMOVAL


b.

Inspect the clutch start switch assembly.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM, CLUTCH START SWITCH ASSEMBLY AND STARTER RELAY ASSEMBLY (ST RELAY)

NG

REPLACE CLUTCH START SWITCH ASSEMBLY

9.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM, CLUTCH START SWITCH ASSEMBLY AND STARTER RELAY ASSEMBLY (ST RELAY)
a.

Disconnect the G213 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A40*1 or r1*2 clutch start switch assembly connector.

·

*1: for LHD

·

*2: for RHD



c.

Remove the starter relay assembly (ST relay).


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G213-10 (STAR) - A40-2*1 Always Below 1 Ω
G213-10 (STAR) - r1-2*2 Always Below 1 Ω
G213-12 (STA) - A40-1*1 Always Below 1 Ω
G213-12 (STA) - r1-1*2 Always Below 1 Ω
G213-10 (STAR) or A40-2 - Body ground*1 Always 10 kΩ or higher
G213-10 (STAR) or r1-2 - Body ground*2 Always 10 kΩ or higher
G213-12 (STA) or A40-1 - Body ground*1 Always 10 kΩ or higher
G213-12 (STA) or r1-1 - Body ground*2 Always 10 kΩ or higher


·

*1: for LHD

·

*2: for RHD



Result:
Proceed to
OK
NG



OK

10.INSPECT STARTER RELAY ASSEMBLY (ST RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT STARTER RELAY ASSEMBLY (ST RELAY)

Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE STARTER RELAY ASSEMBLY

11.READ VALUE USING GTS (STOP LIGHT SWITCH1)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Power Source Control / Data List.


e.

Read the Data List according to the display on the GTS.

Power Source Control
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Switch1 State of brake pedal OFF or ON OFF: Brake pedal released
ON: Brake pedal depressed
·

Use this item to determine if the stop light switch assembly is malfunctioning.

·

The engine cannot be started when this item is OFF.

·

If the stop light switch assembly is malfunctioning, the engine can be started by pressing and holding the engine switch for a certain period of time.



OK:

The GTS display changes correctly in response to the brake pedal operation.



Result:
Proceed to
OK
NG



OK

12.READ VALUE USING GTS (Neutral SW/ Clutch SW)

NG

40.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - POWER SUPPLY AND BODY GROUND)
12.READ VALUE USING GTS (Neutral SW/ Clutch SW)
a.

Enter the following menus: Body Electrical / Power Source Control / Data List.


b.

Read the Data List according to the display on the GTS.

Power Source Control
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Neutral SW/ Clutch SW Shift position (P and N) ON or OFF ON: Shift lever in P or N
OFF: Shift lever in any position other than P or N
·

Use this item to determine whether the park/neutral start switch assembly is malfunctioning.

·

When the engine cannot be started due to a park/neutral start switch assembly malfunction, OFF is displayed.



OK:

The GTS display changes correctly in response to the shift state.



Result:
Proceed to
OK
NG



OK

13.READ VALUE USING GTS (STARTER REQUEST SIGNAL)

NG

36.READ VALUE USING GTS (Neutral SW/ Clutch SW)
13.READ VALUE USING GTS (STARTER REQUEST SIGNAL)
a.

Enter the following menus: Body Electrical / Power Source Control / Data List.


b.

Read the Data List according to the display on the GTS.

Power Source Control
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Starter Request Signal Engine start request signal status OFF or ON OFF: The engine switch is not pressed
ON: With the shift lever in P and the brake pedal depressed, the engine switch is pressed and held
·

When the engine cannot be started due to a start request signal malfunction, OFF is displayed.

·

When the engine switch is pressed, the duration of time that ON is displayed will be extremely short. As such, the engine switch needs to be pressed and held for a certain period of time.



NOTICE:

Check that the key indicator display is displayed in the combination meter assembly, and then press the engine switch.


OK:

The GTS display changes correctly in response to the engine switch operation.



Result:
Proceed to
OK
NG



OK

14.READ VALUE USING GTS (STARTER SW)

NG

34.CHECK STEERING LOCK
14.READ VALUE USING GTS (STARTER SW)
a.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


b.

Shift lever in P.


c.

Enter the following menus: Body Electrical / Starting Control / Data List.


d.

Read the Data List while pressing the engine switch with the brake pedal depressed according to the display on the GTS.

Starting Control
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Starter SW Starter operation request OFF or ON OFF: Starter operation not requested
ON: Starter operation requested
When OFF is displayed, the engine will not crank.

OK:

The GTS display changes.



Result:
Proceed to
OK (w/ Stop and Start System)
OK (w/o Stop and Start System)
NG



OK (w/ Stop and Start System)

15.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST RELAY)

OK (w/o Stop and Start System)

25.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST RELAY)

NG

31.READ VALUE USING GTS (Shift P Signal)
15.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST RELAY)
a.
C421133C01
0.156,0.125 0.521,0.469 0.365,0.344 10 false *a
*a Engine Room Relay Block
(Starter Relay Assembly (ST Relay) Installation Terminal)


Remove the starter relay assembly (ST relay).


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Starter relay assembly (ST relay) installation terminal 2 - Body ground Engine switch pressed and held with brake pedal depressed (starter on) → Approximately 1 second after engine switch released (starter off) 6 V or higher* → 1.0 V or less


HINT:

*: While the engine is cranking, the battery voltage may drop to approximately 6 V.



Result:
Proceed to
OK
NG



OK

16.CHECK HARNESS AND CONNECTOR (ST RELAY - POWER SUPPLY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK HARNESS AND CONNECTOR (ST RELAY - POWER SUPPLY AND BODY GROUND)
a.
C421133C01
0.156,0.125 0.521,0.469 0.365,0.344 10 false *a
*a Engine Room Relay Block
(Starter Relay Assembly (ST Relay) Installation Terminal)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Starter relay assembly (ST relay) installation terminal 1 - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Starter relay assembly (ST relay) installation terminal 5 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

17.INSPECT STARTER RELAY ASSEMBLY (ST RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.INSPECT STARTER RELAY ASSEMBLY (ST RELAY)
a.

Inspect the starter relay assembly (ST relay).

Click hereEngine / Hybrid System>1GD-FTV (STARTING)>RELAY>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

18.CHECK HARNESS AND CONNECTOR (STARTER RELAY ASSEMBLY (ST RELAY) - STARTER ASSEMBLY)

NG

REPLACE STARTER RELAY ASSEMBLY (ST RELAY)

18.CHECK HARNESS AND CONNECTOR (STARTER RELAY ASSEMBLY (ST RELAY) - STARTER ASSEMBLY)
a.

Disconnect the D14 starter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Starter Relay Assembly (ST relay) installation terminal 3 - D14-1 (SL1) Always Below 1 Ω
Starter Relay Assembly (ST relay) installation terminal 3 or D14-1 (SL1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

19.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST NO. 2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST NO. 2 RELAY)
a.
C378519C03
0.156,0.125 0.521,0.469 0.365,0.344 10 false *a
*a Engine Room Relay Block
(Starter Relay Assembly (ST NO. 2 relay) Installation Terminal)


Remove the starter relay assembly (ST NO. 2 relay).


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Starter relay assembly (ST NO. 2 relay) installation terminal 2 - Body ground Engine switch pressed and held with brake pedal depressed (starter on) → Approximately 1 second after engine switch released (starter off) 6 V or higher* → 1.0 V or less


HINT:

*: While the engine is cranking, the battery voltage may drop to approximately 6 V.



Result:
Proceed to
OK
NG



OK

20.CHECK HARNESS AND CONNECTOR (ST NO. 2 RELAY - POWER SUPPLY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

20.CHECK HARNESS AND CONNECTOR (ST NO. 2 RELAY - POWER SUPPLY AND BODY GROUND)
a.
C378519C03
0.156,0.125 0.521,0.469 0.365,0.344 10 false *a
*a Engine Room Relay Block
(Starter Relay Assembly (ST NO. 2 relay) Installation Terminal)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Starter relay assembly (ST NO. 2 relay) installation terminal 1 - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Starter relay assembly (ST NO. 2 relay) installation terminal 5 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

21.INSPECT STARTER RELAY ASSEMBLY (ST NO. 2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

21.INSPECT STARTER RELAY ASSEMBLY (ST NO. 2 RELAY)
a.

Inspect the starter relay assembly (ST NO. 2 relay).

Click hereEngine / Hybrid System>1GD-FTV (STARTING)>RELAY>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

22.CHECK HARNESS AND CONNECTOR (STARTER RELAY ASSEMBLY (ST NO. 2 RELAY) - STARTER ASSEMBLY)

NG

REPLACE STARTER RELAY ASSEMBLY (ST NO.2 RELAY)

22.CHECK HARNESS AND CONNECTOR (STARTER RELAY ASSEMBLY (ST NO. 2 RELAY) - STARTER ASSEMBLY)
a.

Disconnect the D14 starter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Starter Relay Assembly (ST NO. 2 relay) installation terminal 3 - D14-2 (SL2) Always Below 1 Ω
Starter Relay Assembly (ST NO. 2 relay) installation terminal 3 or D14-2 (SL2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

23.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - POWER SUPPLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

23.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - POWER SUPPLY)
a.
B492201C04
1.625,2.156 1.969,2.354 0.344,0.198 1.677,2.177 2.135,2.375 0.458,0.198 10 false D13
*a Wire harness connector
(to Starter Assembly)


Disconnect the starter assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D13-1 (B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

24.INSPECT STARTER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

25.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST RELAY)
a.

except 1GD-FTV:

i.
C378519C03
0.156,0.125 0.521,0.469 0.365,0.344 10 false *a
*a Engine Room Relay Block
(Starter Relay Assembly (ST Relay) Installation Terminal)


Remove the starter relay assembly (ST relay).


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Starter relay assembly (ST relay) installation terminal 2 - Body ground Engine switch pressed and held with clutch pedal depressed (starter on) → Approximately 1 second after engine switch released (starter off) 6 V or higher* → 1.0 V or less


HINT:

*: While the engine is cranking, the battery voltage may drop to approximately 6 V.




b.

for 1GD-FTV:

i.
C421133C01
0.156,0.125 0.521,0.469 0.365,0.344 10 false *a
*a Engine Room Relay Block
(Starter Relay Assembly (ST Relay) Installation Terminal)


Remove the starter relay assembly (ST relay).


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Starter relay assembly (ST relay) installation terminal 2 - Body ground Engine switch pressed and held with clutch pedal depressed (starter on) → Approximately 1 second after engine switch released (starter off) 6 V or higher* → 1.0 V or less


HINT:

*: While the engine is cranking, the battery voltage may drop to approximately 6 V.




Result:
Proceed to
OK
NG



OK

26.CHECK HARNESS AND CONNECTOR (ST RELAY - POWER SUPPLY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

26.CHECK HARNESS AND CONNECTOR (ST RELAY - POWER SUPPLY AND BODY GROUND)
a.

except 1GD-FTV:

i.
C378519C03
0.156,0.125 0.521,0.469 0.365,0.344 10 false *a
*a Engine Room Relay Block
(Starter Relay Assembly (ST Relay) Installation Terminal)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Starter relay assembly (ST relay) installation terminal 1 - Body ground Always Below 1 Ω



ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Starter relay assembly (ST relay) installation terminal 5 - Body ground Always 11 to 14 V




b.

for 1GD-FTV:

i.
C421133C01
0.156,0.125 0.521,0.469 0.365,0.344 10 false *a
*a Engine Room Relay Block
(Starter Relay Assembly (ST Relay) Installation Terminal)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Starter relay assembly (ST relay) installation terminal 1 - Body ground Always Below 1 Ω



ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Starter relay assembly (ST relay) installation terminal 5 - Body ground Always 11 to 14 V




Result:
Proceed to
OK
NG



OK

27.INSPECT STARTER RELAY ASSEMBLY (ST RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

27.INSPECT STARTER RELAY ASSEMBLY (ST RELAY)

Result:
Proceed to
OK
NG



OK

28.CHECK HARNESS AND CONNECTOR (STARTER RELAY ASSEMBLY (ST RELAY) - STARTER ASSEMBLY)

NG

REPLACE STARTER RELAY ASSEMBLY (ST RELAY)

28.CHECK HARNESS AND CONNECTOR (STARTER RELAY ASSEMBLY (ST RELAY) - STARTER ASSEMBLY)
a.

Disconnect the D12*1, C158*2, D10*3, *4 and D11*3, *5 starter assembly connector.

·

*1: for 1GR-FE

·

*2: for 2TR-FE

·

*3: for 1GD-FTV

·

*4: for Cold Area

·

*5: except Cold Area



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Starter Relay Assembly (ST relay) installation terminal 3 - D12-1 (ST)*1 Always Below 1 Ω
Starter Relay Assembly (ST relay) installation terminal 3 or D12-1 (ST) - Body ground*1 Always 10 kΩ or higher
Starter Relay Assembly (ST relay) installation terminal 3 - C158-1 (ST)*2 Always Below 1 Ω
Starter Relay Assembly (ST relay) installation terminal 3 or C158-1 (ST) - Body ground*2 Always 10 kΩ or higher
Starter Relay Assembly (ST relay) installation terminal 3 - D10-1 (ST)*3, *4 Always Below 1 Ω
Starter Relay Assembly (ST relay) installation terminal 3 or D10-1 (ST) - Body ground*3, *4 Always 10 kΩ or higher
Starter Relay Assembly (ST relay) installation terminal 3 - D11-1 (ST)*3, *5 Always Below 1 Ω
Starter Relay Assembly (ST relay) installation terminal 3 or D11-1 (ST) - Body ground*3, *5 Always 10 kΩ or higher


·

*1: for 1GR-FE

·

*2: for 2TR-FE

·

*3: for 1GD-FTV

·

*4: for Cold Area

·

*5: except Cold Area



Result:
Proceed to
OK
NG



OK

29.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - POWER SUPPLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

29.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - POWER SUPPLY)
a.
B492201C05
2.688,0.771 3.031,0.969 0.344,0.198 2.688,1.042 3.031,1.24 0.344,0.198 2.677,1.323 3.021,1.521 0.344,0.198 2.677,1.583 3.021,1.781 0.344,0.198 2.771,0.792 3.083,0.99 0.313,0.198 10 false D1 2.75,1.063 3.063,1.26 0.313,0.198 10 false D4 2.76,1.344 3.073,1.542 0.313,0.198 10 false D8 2.75,1.583 3.063,1.781 0.313,0.198 10 false D9 3.052,1.594 3.427,1.844 0.375,0.25 10 false *3, *5 3.042,1.365 3.417,1.615 0.375,0.25 10 false *3, *4 3.052,1.073 3.427,1.323 0.375,0.25 10 false *2 3.052,0.792 3.427,1.042 0.375,0.25 10 false *1 0.198,2.365 1.469,2.635 1.271,0.271 10 false *1: for 1GR-FE 0.198,2.719 1.469,2.99 1.271,0.271 10 false *2: for 2TR-FE 0.208,3.063 1.479,3.333 1.271,0.271 10 false *3: for 1GD-FTV 1.417,2.688 2.865,2.958 1.448,0.271 10 false *4: except Cold Area 1.417,3.063 2.865,3.333 1.448,0.271 10 false *5: for Cold Area 0.188,0.219 1.458,0.49 1.271,0.271 10 false *a
*a Wire harness connector
(to Starter Assembly)


Disconnect the starter assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D1-1 (B) - Body ground*1 Always 11 to 14 V
D4-1 (B) - Body ground*2 Always 11 to 14 V
D8-1 (B) - Body ground*3, *4 Always 11 to 14 V
D9-1 (B) - Body ground*3, *5 Always 11 to 14 V


·

*1: for 1GR-FE

·

*2: for 2TR-FE

·

*3: for 1GD-FTV

·

*4: except Cold Area

·

*5: for Cold Area



Result:
Proceed to
OK
NG



OK

30.INSPECT STARTER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

30.INSPECT STARTER ASSEMBLY
a.


Result:
Proceed to
OK (for 1GR-FE)
OK (for 2TR-FE)
OK (for 1GD-FTV)
OK (for 1GD-FTV (w/ Urea SCR System))
OK (for 1GD-FTV (w/ DPF))
NG



OK (for 1GR-FE)

OK (for 2TR-FE)

OK (for 1GD-FTV)

OK (for 1GD-FTV (w/ Urea SCR System))

OK (for 1GD-FTV (w/ DPF))

NG

31.READ VALUE USING GTS (Shift P Signal)
a.

Enter the following menus: Body Electrical / Power Source Control / Data List.


b.

Read the Data List according to the display on the GTS.

Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift P Signal P position signal status Normal2, Normal3, Normal4, Normal5 or Unknown Normal2: Signal normal and park (P) selected
Normal3: Signal normal and shift state other than (P)
Normal4: Signal normal and park (N) selected
Normal5: Signal normal and park other than (P) or (N) selected
Unknown: -
Use this item to determine if the P position signal is malfunctioning.

OK:

The GTS display changes correctly in response to the shift state.



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

32.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - TRANSMISSION FLOOR SHIFT ASSEMBLY (SHIFT LOCK CONTROL ECU))
32.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - TRANSMISSION FLOOR SHIFT ASSEMBLY (SHIFT LOCK CONTROL ECU))
a.

Disconnect the G215 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the G45 transmission floor shift assembly (shift lock control ECU).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G215-22 (P) - G45-11 (P2) Always Below 1 Ω
G215-22 (P) or G45-11 (P2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

33.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

33.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Reconnect the G215 certification ECU (smart key ECU assembly) connector.


b.
C277841C77
1.417,0.094 1.885,0.333 0.469,0.24 0.948,1.615 1.26,0.927 true 0.104,0.052 0.302,0.219 0.198,0.167 10 false *a 0.833,1.646 1.063,1.844 0.229,0.198 10 false P 1.479,0.135 1.948,0.333 0.469,0.198 10 false G215
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G215-22 (P) - Body ground Shift lever in P → Shift lever not in P 9 V or higher → 2.76 V or less



Result:
Proceed to
OK
NG



OK

REPLACE TRANSMISSION FLOOR SHIFT ASSEMBLY (SHIFT LOCK CONTROL ECU)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

34.CHECK STEERING LOCK
a.

Check that the steering unlocks when the engine switch is turned on (ACC).

OK:

The steering unlocks.



Result:
Proceed to
OK
NG



OK

35.CHECK THEFT WARNING INDICATOR LIGHT ASSEMBLY (SECURITY INDICATOR LIGHT) (IMMOBILISER FUNCTION UNSET)

NG

GO TO STEERING LOCK SYSTEM (Unable to Unlock Steering Wheel (Engine cannot Start))

35.CHECK THEFT WARNING INDICATOR LIGHT ASSEMBLY (SECURITY INDICATOR LIGHT) (IMMOBILISER FUNCTION UNSET)
a.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


b.

for Automatic Transmission:

Shift lever in P.


c.

Press the engine switch with the brake pedal*1 or clutch pedal*2 released and check that the theft warning indicator light assembly (security indicator light) changes from blinking to off at the same time that the power source mode changes to on (ACC).

*1: for Automatic Transmission

*2: for Manual Transmission


OK:

The theft warning indicator light assembly (security indicator light) changes from blinking to off at the same time that the power source mode changes to on (ACC).


HINT:

The immobiliser function can be determined to be operating correctly if the theft warning indicator light assembly (security indicator light) changes from blinking to off at the same time that the power source mode changes to on (ACC).



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

GO TO ENGINE IMMOBILISER SYSTEM (w/ Entry and Start System) (Immobiliser System does not Operate Properly)

36.READ VALUE USING GTS (Neutral SW/ Clutch SW)
a.

Disconnect the C34*1, C154*2 and G184*3 ECM connector.

·

*1: for 1GR-FE

·

*2: for 2TR-FE

·

*3: for 1GD-FTV



b.

Read the Data List according to the display on the GTS.

Power Source Control
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Neutral SW/ Clutch SW Shift position (P and N) ON or OFF ON: Shift lever in P or N
OFF: Shift lever in any position other than P or N
·

Use this item to determine whether the park/neutral start switch assembly is malfunctioning.

·

When the engine cannot be started due to a park/neutral start switch assembly malfunction, OFF is displayed.



OK:

The GTS display changes correctly in response to the shift state.



Result:
Proceed to
OK
NG



OK

NG

37.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
37.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Remove the park/neutral position switch.

for AC60F: Click hereDrivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>REMOVAL


b.

Inspect the park/neutral position switch.

for AC60F: Click hereDrivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

38.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM, PARK/NEUTRAL POSITION SWITCH ASSEMBLY AND STARTER RELAY ASSEMBLY (ST RELAY)

NG

REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

38.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM, PARK/NEUTRAL POSITION SWITCH ASSEMBLY AND STARTER RELAY ASSEMBLY (ST RELAY)
a.

Disconnect the G213 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the C159 park/neutral position switch connector.


c.

Remove the starter relay assembly (ST relay).


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G213-10 (STAR) - C159-4 (B) Always Below 1 Ω
G213-12 (STA) - C159-5 (L) Always Below 1 Ω
G213-10 (STAR) or C159-4 (B) - Body ground Always 10 kΩ or higher
G213-12 (STA) or C159-5 (L) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

39.INSPECT STARTER RELAY ASSEMBLY (ST RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

39.INSPECT STARTER RELAY ASSEMBLY (ST RELAY)

Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE STARTER RELAY ASSEMBLY

40.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - POWER SUPPLY AND BODY GROUND)
a.
B492209C01
1.417,0.208 1.865,0.448 0.448,0.24 2.656,1.844 2.427,1.844 2.427,1.844 2.177,1.156 true 1.354,1.177 0.854,1.833 0.854,1.833 0.646,1.833 true 1.5,0.229 1.958,0.427 0.458,0.198 10 false A99 0.177,0.156 0.635,0.354 0.458,0.198 10 false *a 2.719,1.771 3.177,1.969 0.458,0.198 10 false B 0.333,1.75 0.792,1.948 0.458,0.198 10 false GND
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the stop light switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A99-7 (B) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A99-2 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

41.CHECK HARNESS AND CONNECTOR CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM, TRANSMISSION FLOOR SHIFT ASSEMBLY (SHIFT LOCK CONTROL ECU) AND BRAKE ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

41.CHECK HARNESS AND CONNECTOR CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM, TRANSMISSION FLOOR SHIFT ASSEMBLY (SHIFT LOCK CONTROL ECU) AND BRAKE ACTUATOR ASSEMBLY)
a.

Disconnect the G213 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the G56*1, G180*2 and G185*3 ECM connector.

·

*1: for 1GR-FE

·

*2: for 2TR-FE

·

*3: for 1GD-FTV



c.

Disconnect the A6*1 or A7*2 brake actuator assembly (skid control ECU) connector.

·

*1: for Vacuum Brake Booster

·

*2: for Hydraulic Brake Booster



d.

Disconnect the G45 transmission floor shift assembly (shift lock control ECU) connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G213-2 (STP1) - A99-3 (L) Always Below 1 Ω
G213-2 (STP1) or A99-3 (L) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

42.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

42.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY