Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2021.08
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0463852 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P1C8149  High Voltage Power Resource Circuit Consumption Circuit Short  P1C8249  High Voltage Power Resource Circuit Over Loading  


DTC SUMMARY

MALFUNCTION DESCRIPTION


The EV control ECU monitors the high-voltage wiring between the EV supply battery assembly and inverter with converter assembly and detects a short circuit malfunction or high-voltage system operation malfunction.

The cause of this malfunction may be one of the following:

Battery current sensor (IB) circuit malfunction
·

Battery current sensor (IB) malfunction

·

Motor generator control ECU (MG ECU) malfunction

·

Communication (wire harness) malfunction


High voltage system malfunction
·

EV supply battery assembly malfunction

·

No. 1 EV battery junction block assembly malfunction

·

Inverter with converter assembly malfunction

·

Air conditioner system malfunction

·

High-voltage wire harness malfunction

·

High-voltage connector or connection malfunction

·

FC converter assembly malfunction

·

FC system high-voltage auxiliary machine malfunction

·

Voltage inverter (for 1500W Type)


Low-voltage circuit (12 V) malfunction
·

EV control ECU malfunction

·

Low voltage wire harness malfunction

·

Low voltage connector malfunction

·

FC system high-voltage auxiliary machine malfunction



DESCRIPTION

Refer to the description for DTC P0AE411.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AE411

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P1C8149 High Voltage Power Resource Circuit Consumption Circuit Short High-voltage circuit malfunctions between the EV supply battery and inverter with converter assembly.
Excessive overcurrent equal to a short occurs during precharge (time from when SMRP turns on until SMRG turns on).
(1 trip detection logic)
·

Compressor with motor assembly

·

Inverter with converter assembly

·

No. 1 EV battery junction block assembly

·

Floor under wire

·

EV control ECU

·

FC converter assembly

·

FC inverter input terminal

·

Air conditioning compressor cable

·

Electric heater sub-assembly

·

FC cooling water pump cable

·

No. 1 battery pack wire

·

FC junction cable

·

FC cooling water pump inverter assembly

·

FC hydrogen pump inverter assembly

·

Front compartment main wire

·

Voltage inverter*

·

Socket inverter wire*


Master Warning:
Comes on
EV A
P1C8249 High Voltage Power Resource Circuit Over Loading High-voltage circuit malfunctions between the EV supply battery and inverter with converter assembly.
Small battery overcurrent occurs during precharge (time from when SMRP turns on until SMRG turns on) and current continues to flow after precharge.
(1 trip detection logic)
·

Compressor with motor assembly

·

Inverter with converter assembly

·

No. 1 EV battery junction block assembly

·

Floor under wire

·

EV control ECU

·

FC converter assembly

·

FC inverter input terminal

·

Air conditioning compressor cable

·

Electric heater sub-assembly

·

FC cooling water pump cable

·

No. 1 battery pack wire

·

FC junction cable

·

FC cooling water pump inverter assembly

·

FC hydrogen pump inverter assembly

·

Front compartment main wire

·

Voltage inverter*

·

Socket inverter wire*


Master Warning:
Comes on
EV A

*: for 1500W Type

Related Data List
DTC No. Data List
P1C8149
·

Hybrid/EV Battery Voltage

·

Hybrid/EV Battery Current

·

VL-Voltage before Boosting

·

VH-Voltage after Boosting


P1C8249

CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 10 minutes or more.

3.

Turn the ignition switch to ON (READY) and wait for 30 seconds or more.

4.

Turn the ignition switch off and wait for 10 minutes or more.

5.

Enter the following menus: Powertrain / EV / Utility / All Readiness.

6.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

Refer to the wiring diagram for DTC P0AA649.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AA649

Refer to the wiring diagram for DTC P1CCC96.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P1CCC96

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the EV battery service plug grip and FC converter power outlet cable on FC converter side.

Make sure to remove the service plug gripfirst.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the EV supply battery assembly

-

Disconnecting the low voltage connector of the FC converter assembly

-

Disconnecting the low voltage connector of the voltage inverter (for 1500W Type Voltage Inverter)


·
A484004

To prevent electric shock, make sure to remove the EV battery service plug grip and FC converter power outlet cable on FC converter side to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, store them according to the following guidelines to prevent other technicians from accidentally reconnecting them while work is being performed on the high voltage systems.

-

The technician performing the work should put the EV battery service plug grip in their pocket and carry it with them.

-

Remove the FC converter power outlet cable on FC converter side with a "HIGH-VOLTAGE, DO NOT TOUCH" caution tag attached to it for other technicians.


·
A484005C01
1.667,0.74 2.115,0.427 true 2.188,0.385 2.448,0.552 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip and FC converter power outlet cable on FC converter side, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly snd FC converter assembly.


·

Make sure to insulate the high-voltage connectors and terminals of the EV supply battery assembly with insulating tape after removing it.

If the EV supply battery assembly stored without insulating the connectors and terminals, electric shock or fire may result.

·
A484932

Since high voltage accumulates within the FC stack assembly with FC converter, never perform the work of separating the FC stack assembly with FC converter into the FC converter assembly and FC stack assembly without first performing electrical charge discharge (forced electrical charge discharge or electrical charge self-discharge), because doing so is dangerous.

Click hereEngine / Hybrid System>FC CONTROL>FC STACK>REMOVAL

·

Removing and installing the FC stack assembly without first discharging the electrical charge may result in an electric shock due to the high voltage circuit.



NOTICE:
·

After turning the ignition switch off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



PROCEDURE

1.CHECK DTC OUTPUT (EV, EV BATTERY, FCDC)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Powertrain > EV Battery > Trouble Codes
50001 398
Powertrain > FCDC > Trouble Codes
50001 493
Result:
Result Proceed to
P1C8149 or P1C8249 only is output, or DTCs except the ones in the tables below are also output A
Any hybrid control system DTCs in the table below are output B
Any hybrid battery system DTCs in the table below are output C
Any FC control system DTCs in the table below are output D


Malfunction Content System Relevant DTC
Microcomputer malfunction Hybrid control system P060647 Hybrid/EV Powertrain Control Module Processor Watchdog / Safety MCU Failure
P060B49 Hybrid/EV Powertrain Control Module A/D Processing Internal Electronic Failure
P060687 Hybrid/EV Powertrain Control Module Processor to Monitoring Processor Missing Message
P060A47 Hybrid/EV Powertrain Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060A87 Hybrid/EV Powertrain Control Module Processor from Monitoring Processor Missing Message
Hybrid battery system P060B49 Hybrid/EV Battery Energy Control Module A/D Processing Internal Electronic Failure
P060687 Hybrid/EV Battery Energy Control Module Processor to Monitoring Processor Missing Message
P060A47 Hybrid/EV Battery Energy Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060A87 Hybrid/EV Battery Energy Control Module Processor from Monitoring Processor Missing Message
P060B16 Hybrid/EV Battery Energy Control Module A/D Processing Circuit Voltage Below Threshold
P0E2D00 Hybrid/EV Battery Energy Control Module Hybrid/EV Battery Monitor Performance
Communication system malfunction Hybrid control system U011187 Lost Communication with Hybrid/EV Battery Energy Control Module "A" Missing Message
Sensor and actuator circuit malfunction Hybrid control system P0B231C Hybrid/EV Battery "A" Voltage Sensor Voltage Out of Range
P0ABF00 Hybrid/EV Battery Current Sensor "A" Circuit Range/Performance
P0A1114 DC/DC Converter Enable Circuit Short to Ground or Open
P0A1112 DC/DC Converter Enable Circuit Short to Auxiliary Battery
P1CCC96 DC/DC Converter Enable Component Internal Failure
Hybrid battery system P0ABF11 Hybrid/EV Battery Current Sensor "A" Circuit Short to Ground
P0B0E11 Hybrid/EV Battery Current Sensor "B" Circuit Short to Ground
P0B0E15 Hybrid/EV Battery Current Sensor "B" Circuit Short to Auxiliary Battery or Open
P0ABF15 Hybrid/EV Battery Current Sensor "A" Circuit Short to Auxiliary Battery or Open
P301A1C Hybrid Battery Stack 1 Cell Voltage Detection Voltage Out of Range
P1A001C Hybrid Battery Stack 2 Cell Voltage Detection Voltage Out of Range
P1AFD1C Flying Capacitor/Internal Control Module Hybrid/EV Battery Monitor Voltage Out of Range
P0ABF28 Hybrid/EV Battery Current Sensor "A" Signal Bias Level Out of Range / Zero Adjustment Failure
P0ABF2A Hybrid/EV Battery Current Sensor "A" Signal Stuck In Range
P1CBB12 Hybrid/EV Battery Current Sensor Power Supply Circuit Short to Auxiliary Battery
P1CBB14 Hybrid/EV Battery Current Sensor Power Supply Circuit Short to Ground or Open
P0B1362 Hybrid/EV Battery Current Sensor "A"/"B" Signal Compare Failure
System malfunction Hybrid control system P0A1F94 Hybrid/EV Battery Energy Control Module Unexpected Operation
Motor generator control system P0D3319 DC/DC Converter Circuit Current Above Threshold

HINT:

P1C8149 or P1C8249 may be output as a result of the malfunction indicated by the DTCs above.

(a)

The chart above is listed in inspection order of priority.

(b)

Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)





Post-procedure1

a.

Turn the ignition switch off.



A

2.CHECK CONNECTOR CONNECTION CONDITION (EV CONTROL ECU CONNECTOR)

B

GO TO DTC CHART (HYBRID CONTROL SYSTEM)

C

D

2.CHECK CONNECTOR CONNECTION CONDITION (EV CONTROL ECU CONNECTOR)

OK

3.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

NG

CONNECT SECURELY

3.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A001C

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

4.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - EV CONTROL ECU)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - EV CONTROL ECU)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A20 inverter with converter assembly connector.


c.

Disconnect the A17 EV control ECU connector.


Procedure1

a.
A479449C06
1.51,0.198 1.906,0.51 0.396,0.313 2.042,2.083 2.438,2.396 0.396,0.313 2.229,1.688 1.958,1.177 true 2.781,4.292 2.469,3.927 true 0.083,0.083 0.396,0.24 0.313,0.156 10 false *a 0.083,2 0.396,2.156 0.313,0.156 10 false *b 2.135,2.188 2.594,2.385 0.458,0.198 10 false A17 1.604,0.281 2.063,0.479 0.458,0.198 10 false A20 2.271,1.75 2.729,1.948 0.458,0.198 10 false NODD 2.792,4.344 3.25,4.542 0.458,0.198 10 false NODD
*a Front view of wire harness connector
(to Inverter with Converter Assembly)
*b Rear view of wire harness connector
(to EV Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition

Click Location & Routing(A20,A17)Location & Routing

Click Connector(A20)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

Click Connector(A17)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A20-5 (NODD) - A17-18 (NODD) Ignition switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition

Click Location & Routing(A20,A17)Location & Routing

Click Connector(A20)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

Click Connector(A17)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A20-5 (NODD) or A17-18 (NODD) - Body ground and other terminals Ignition switch off 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the A17 EV control ECU connector.


b.

Reconnect the A20 inverter with converter assembly connector.



OK

5.CHECK EV CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK EV CONTROL ECU
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the ignition switch to ON.


Procedure1

a.
A478491C43
1.979,0.802 2.375,1.156 0.396,0.354 2.219,1.677 1.948,2.479 true 2.438,1.823 2.917,2.469 true 0.104,0.104 0.417,0.26 0.313,0.156 10 false *a 2.073,0.917 2.375,1.083 0.302,0.167 10 false A17 1.833,2.51 2.135,2.677 0.302,0.167 10 false E1 2.781,2.51 3.24,2.729 0.458,0.219 10 false NODD
*a Component with harness connected
(EV Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A17)Location & Routing

Click Connector(A17)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A17-18 (NODD) - A17-4 (E1) Ignition switch ON Below 1.5 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.



OK

6.CHECK COMPRESSOR WITH MOTOR ASSEMBLY

NG

6.CHECK COMPRESSOR WITH MOTOR ASSEMBLY
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A483175C02
0,0 0.313,0.198 0.313,0.198 10 true *A 0.021,2.344 0.333,2.542 0.313,0.198 10 true *B
*A for LHD
*B for RHD


Disconnect the FC cooling water pump cable from the FC converter assembly.


Procedure1

a.
A481492C02
1.521,0.135 1.927,0.479 0.406,0.344 1.125,1.677 1.49,1.24 true 2.177,1.688 1.885,1.25 true 2.365,0.885 2.031,0.99 true 2.396,0.802 2.708,0.958 0.313,0.156 10 false *1 0.135,0.104 0.448,0.26 0.313,0.156 10 false *a 1.667,0.24 1.979,0.396 0.313,0.156 10 false b4 0.979,1.698 1.469,1.927 0.49,0.229 10 false N 2.208,1.708 2.698,1.938 0.49,0.229 10 false P
*1 Shield Ground
*a FC Cooling Water Pump Cable
(FC Converter Assembly Side)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection
(Tester Probe Polarity)
Condition Specified Condition

Click Location & Routing(b4)Location & Routing

Click Connector(b4)Engine Compartment>FC Cooling Water Pump Cable>FC Converter Assembly

b4-1 (N) (Negative (-) probe) - b4-2 (P) (Positive (+) probe) Ignition switch off 100 kΩ or higher


NOTICE:
·

Do not use a megohmmeter.

·

Read the resistance after the value has stabilized.

·

Be sure to inspect with connecting the tester probes to the tips of the terminal.



Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the FC cooling water pump cable.



OK

7.CHECK FC CONVERTER ASSEMBLY

NG

14.CHECK FC COOLING WATER PUMP CABLE
7.CHECK FC CONVERTER ASSEMBLY
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A485259C01
0.719,0.094 1.156,0.427 0.438,0.333 1.948,0.063 2.385,0.396 0.438,0.333 2.49,0.479 2.927,0.813 0.438,0.333 0.792,2.531 1.229,2.865 0.438,0.333 2.104,2.521 2.542,2.854 0.438,0.333 2.458,2.927 2.896,3.26 0.438,0.333 0.073,0.073 0.281,0.271 0.208,0.198 10 true *A 0.104,2.479 0.302,2.667 0.198,0.188 10 true *B 0.854,0.156 1.063,0.354 0.208,0.198 10 true b4 2.083,0.125 2.302,0.333 0.219,0.208 10 true N3 2.625,0.552 2.823,0.76 0.198,0.208 10 true x2 0.927,2.604 1.135,2.802 0.208,0.198 10 true b4 2.25,2.594 2.469,2.802 0.219,0.208 10 true N3 2.604,3 2.802,3.208 0.198,0.208 10 true x2
*A for LHD
*B for RHD


Disconnect the FC junction cable connectors, floor under wire and FC cooling water pump cable from the FC converter assembly.


Procedure1

a.
A484692C02
1.885,0.781 2.292,1.115 0.406,0.333 1.854,1.75 2.021,1.313 true 2.406,1.74 2.198,1.302 true 0.094,0.052 0.406,0.25 0.313,0.198 10 true *a 2.021,0.875 2.219,1.042 0.198,0.167 10 true N3 1.698,1.792 2.188,1.958 0.49,0.167 10 true CBI (+) 2.292,1.792 2.74,1.958 0.448,0.167 10 true CEI (-)
*a Component without harness connected
(FC Converter Assembly)


Measure the resistance according to the value(s) inthe table below.

CAUTION:

Do not use a megohmmeter.


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(N3)Location & Routing

Click Connector(N3)Engine Compartment>Floor Under Wire>FC Converter Assembly

N3-1 (CEI) (Negative (-) probe) - N3-2 (CBI) (Positive (+) probe) Ignition switch off 10 kΩ or higher


NOTICE:

If the polarity of the tester probes is wrong, the correct value cannot be measured.


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

8.CHECK ELECTRIC HEATER SUB-ASSEMBLY

NG

12.REMOVE FC CONVERTER ASSEMBLY
8.CHECK ELECTRIC HEATER SUB-ASSEMBLY
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A483163C01
0.031,0 0.344,0.198 0.313,0.198 10 true *A 0.031,2.479 0.344,2.677 0.313,0.198 10 true *B
*A for LHD
*B for RHD


Disconnect the front compartment main wire connector from the inverter with converter assembly.

HINT:

Make sure that no foreign matter has entered or contaminated the front compartment main wire connector.



Procedure1

a.
A260188C73
0.635,1.198 1.031,1.49 0.396,0.292 1,1.76 1.531,1.531 true 2.396,1.729 1.917,1.531 true 2.344,0.896 2.115,0.938 true 2.396,0.802 2.708,0.958 0.313,0.156 10 false *1 0.135,0.104 0.448,0.26 0.313,0.156 10 false *a 0.719,1.271 1.031,1.427 0.313,0.156 10 false A32 0.635,1.698 1.125,1.927 0.49,0.229 10 false ACPE 2.438,1.698 2.927,1.927 0.49,0.229 10 false ACPB
*1 Shield Ground
*a Front Compartment Main Wire
(Inverter with Converter Assembly Side)


Measure the resistance according to the value(s) inthe table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A32)Location & Routing

Click Connector(A32)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

A32-1 (ACPE) (Negative (-) probe) - A32-2 (ACPB) (Positive (+) probe) Ignition switch off 100 MΩ or higher


NOTICE:
·

Do not use a megohmmeter.

·

Read the resistance after the value hasstabilized.

·

Be sure to inspect with connecting thetester probes to the tips of the terminal.



Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the front compartment main wire connector.



OK

9.CHECK FC JUNCTION CABLE

NG

21.CHECK FRONT COMPARTMENT MAIN WIRE
9.CHECK FC JUNCTION CABLE
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A483165C01
0,0 0.313,0.198 0.313,0.198 10 true *A 0,2.458 0.313,2.656 0.313,0.198 10 true *B
*A for LHD
*B for RHD


Disconnect the FC junction cable from the inverter with converter assembly.


Procedure1

a.
C257176C53
0.438,1.031 0.833,1.344 0.396,0.313 0.969,1.719 1.26,1.188 true 2.25,1.729 1.938,1.177 true 2.635,0.625 2.375,0.771 true 2.688,0.542 3,0.698 0.313,0.156 10 false *1 0.073,0.083 0.385,0.24 0.313,0.156 10 false *a 2.26,1.75 2.677,1.958 0.417,0.208 10 false 2 (N) 0.927,1.75 1.323,1.938 0.396,0.188 10 false 1 (P) 0.583,1.115 0.896,1.271 0.313,0.156 10 false x1
*1 Shield Ground
*a Front view of FC Junction Cable connector
(Inverter with Converter Assembly Side)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(x1)Location & Routing

Click Connector(x1)Engine Compartment>FC Junction Cable>Inverter with Converter Assembly

x1-1 (P) - x1-2 (N) Ignition switch off 10 kΩ or higher


NOTICE:

Be sure not to damage or deform the terminal being inspected.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the FC junction cable.



OK

10.CHECK INVERTER WITH CONVERTER ASSEMBLY

NG

17.CHECK NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY
10.CHECK INVERTER WITH CONVERTER ASSEMBLY
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A483129C01
0.177,0.146 0.448,0.385 0.271,0.24 12 true *A 0.229,2.552 0.479,2.792 0.25,0.24 12 true *B
*A for LHD
*B for RHD


Remove the connector cover assembly from the inverter with converter assembly.


c.
A483163C01
0.031,0 0.344,0.198 0.313,0.198 10 true *A 0.031,2.479 0.344,2.677 0.313,0.198 10 true *B
*A for LHD
*B for RHD


Disconnect the front compartment main wire from the inverter with converter assembly.

HINT:

Make sure that no foreign matter has entered or contaminated the front compartment main wire.



d.
A483165C01
0,0 0.313,0.198 0.313,0.198 10 true *A 0,2.458 0.313,2.656 0.313,0.198 10 true *B
*A for LHD
*B for RHD


Disconnect the FC junction cable from the inverter with converter assembly.

HINT:

Make sure that no foreign matter has entered or contaminated the FC junction cable.



Procedure1

a.
A483167C01
1.365,1.771 1.469,1.771 1.469,1.771 1.604,1.396 true 2.198,1.135 2.313,0.833 2.313,0.833 2.406,0.833 true 2.073,3.615 2.188,3.313 2.188,3.313 2.281,3.313 true 1.26,4.24 1.365,4.24 1.365,4.24 1.5,3.865 true 0,0 0.313,0.198 0.313,0.198 10 true *A 0,2.448 0.313,2.646 0.313,0.198 10 true *B 1.01,4.156 1.302,4.365 0.292,0.208 10 true 2 (-) 2.458,0.75 2.781,0.948 0.323,0.198 10 true 1 (+) 1.063,1.698 1.344,1.917 0.281,0.219 10 true 2 (-) 2.344,3.24 2.667,3.438 0.323,0.198 10 true 1 (+)
*A for LHD
*B for RHD


Measure the resistance according to the value(s) in the table below.

CAUTION:

Do not use a megohmmeter.


Standard Resistance:
Tester Connection Condition Specified Condition
2 (-) (Negative (-) probe) - 1 (+) (Positive (+) probe) Ignition switch off 10 kΩ or higher


NOTICE:

Be sure to inspect with connecting thetester probes to the tips of the terminal.


HINT:

Perform an inspection with the FC junction cable and front compartment main wire removed from the inverter with converter assembly.


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

11.REMOVE FC CONVERTER ASSEMBLY

NG

REPLACE INVERTER WITH CONVERTER ASSEMBLY

11.REMOVE FC CONVERTER ASSEMBLY
HINT:

Click hereEngine / Hybrid System>FC CONTROL>CONVERTER ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT

REPLACE FC CONVERTER ASSEMBLY

12.REMOVE FC CONVERTER ASSEMBLY
HINT:

Click hereEngine / Hybrid System>FC CONTROL>CONVERTER ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT

13.CHECK FC INVERTER INPUT JUNCTION COVER
13.CHECK FC INVERTER INPUT JUNCTION COVER

Pre-procedure1

a.

Remove the FC inverter input junction cover from the FC converter assembly.

HINT:

Click hereEngine / Hybrid System>FC CONTROL>CONVERTER ASSEMBLY>DISASSEMBLY



Procedure1

a.

Measure the resistance according to the value(s) inthe table below.

A493910C01
3.719,1.135 4.135,1.5 0.417,0.365 3.51,2.292 3.844,1.76 true 4.271,2.281 3.979,1.75 true 0.271,0.177 0.583,0.375 0.313,0.198 10 false *a 4.125,2.302 4.625,2.5 0.5,0.198 10 true CEI (-) 3.26,2.302 3.781,2.469 0.521,0.167 10 true CBI (+) 3.854,1.26 4.063,1.427 0.208,0.167 10 true N3
*a FC Inverter Junction Cover - -


CAUTION:

Do not use a megohmmeter.


HINT:

Perform an inspection with the FC inverter input terminal and air conditioning compressor cable still installed to FC converter input junction cover.


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(N3)Location & Routing

Click Connector(N3)Engine Compartment>Floor Under Wire>FC Converter Assembly

N3-1 (CEI) (Negative (-) probe) - N3-2 (CBI) (Positive (+) probe) Ignition switch off 10 MΩ or higher


NOTICE:

If the polarity of the tester probes is wrong, thecorrect value cannot be measured.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the front compartment main wire connector.



OK

REPLACE FC COOLING WATER PUMP INVERTER ASSEMBLY AND FC HYDROGEN PUMP INVERTER ASSEMBLY

NG

15.CHECK AIR CONDITIONING COMPRESSOR CABLE
14.CHECK FC COOLING WATER PUMP CABLE
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A483175C01
0.01,0 0.323,0.198 0.313,0.198 10 true *A 0,2.365 0.313,2.563 0.313,0.198 10 true *B
*A for LHD
*B for RHD


Disconnect the FC cooling water pump cable from the FC converter assembly.


c.
A480830

Disconnect the FC cooling water pump cable from the compressor with motor assembly.

HINT:

Click hereVehicle Interior>HEATING / AIR CONDITIONING>COMPRESSOR>REMOVAL



Procedure1

a.
A481492C02
1.521,0.135 1.927,0.479 0.406,0.344 1.125,1.677 1.49,1.24 true 2.177,1.688 1.885,1.25 true 2.365,0.885 2.031,0.99 true 2.396,0.802 2.708,0.958 0.313,0.156 10 false *1 0.135,0.104 0.448,0.26 0.313,0.156 10 false *a 1.667,0.24 1.979,0.396 0.313,0.156 10 false b4 0.979,1.698 1.469,1.927 0.49,0.229 10 false N 2.208,1.708 2.698,1.938 0.49,0.229 10 false P
*1 Shield Ground
*a FC Cooling Water Pump Cable
(Inverter with Converter Assembly Side)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(b4)Location & Routing

Click Connector(b4)Engine Compartment>FC Cooling Water Pump Cable>FC Converter Assembly

b4-1 (N) - b4-2 (P) Ignition switch off 10 kΩ or higher


NOTICE:

Be sure to inspect with connecting the tester probes to the tips of the terminal.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the FC cooling water pump cable.



OK

REPLACE COMPRESSOR WITH MOTOR ASSEMBLY

NG

REPLACE FC COOLING WATER PUMP CABLE

15.CHECK AIR CONDITIONING COMPRESSOR CABLE

Pre-procedure1

a.
A492128

Remove the air conditioning compressor cable from the FC inverter input junction cover.


b.
A492129

Remove the air conditioning compressor cable from the FC inverter input terminal.


Procedure1

a.
A492122C02
2.448,2.323 2.854,2.656 0.406,0.333 1.333,3.167 1.552,2.469 true 2.021,3.177 1.792,2.469 true 0.094,0.052 0.406,0.25 0.313,0.198 10 true *a 2.594,2.427 2.833,2.594 0.24,0.167 10 true b4 1.302,3.198 1.49,3.385 0.188,0.188 10 true N 2.01,3.208 2.167,3.375 0.156,0.167 10 true P
*a Air Conditioning Compressor Cable


Measure the resistance according to the value(s) inthe table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(b4)Location & Routing

Click Connector(b4)Engine Compartment>FC Cooling Water Pump Cable>FC Converter Assembly

b4-1 (N) - b4-2 (P) Ignition switch off 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

16.REPLACE FC INVERTER INPUT TERMINAL

NG

20.REPLACE AIR CONDITIONING COMPRESSOR CABLE
16.REPLACE FC INVERTER INPUT TERMINAL

NEXT

REPLACE FC COOLING WATER PUMP INVERTER ASSEMBLY AND FC HYDROGEN PUMP INVERTER ASSEMBLY

17.CHECK NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A478504E01
1.375,0.073 1.75,0.333 0.375,0.26 1.865,0.073 2.24,0.333 0.375,0.26 2,0.135 2.313,0.333 0.313,0.198 10 false N1 1.5,0.146 1.813,0.344 0.313,0.198 10 false N2

Disconnect the N1 and N2 floor under wire from the No. 1 EV battery junction block assembly.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

A480853C02
3.021,0.135 3.438,0.448 0.417,0.313 3.74,0.135 4.156,0.448 0.417,0.313 2.792,0.896 2.625,1.125 true 3.469,0.906 3.76,1.115 true 0.146,0.125 0.458,0.323 0.313,0.198 10 false *a 3.771,1.115 4.083,1.313 0.313,0.198 10 true CBI 3.167,0.229 3.479,0.427 0.313,0.198 10 false N2 3.885,0.229 4.198,0.427 0.313,0.198 10 false N1 2.417,1.146 2.729,1.344 0.313,0.198 10 true CEI
*1 Component without harness connected
(No. 1 EV Battery Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(N1,N2)Location & Routing

Click Connector(N1)Body>Floor Under Wire>No. 1 EV Battery Junction Block Assembly

Click Connector(N2)Body>Floor Under Wire>No. 1 EV Battery Junction Block Assembly

N1-1 (CBI) - N2-1 (CEI) Ignition switch off 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

Reconnect the N1 and N2 floor under wire.



OK

18.CHECK FLOOR UNDER WIRE

NG

23.CHECK VEHICLE CONDITION
18.CHECK FLOOR UNDER WIRE
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



Procedure1

a.
A484669C01
0,0 0.313,0.198 0.313,0.198 10 true *A 0,2.479 0.313,2.677 0.313,0.198 10 true *B
*A for LHD
*B for RHD


Disconnect the floor under wire from the FC converter assembly.

HINT:

Make sure that no foreign matter has entered or contaminated the floor under wire.



b.
A478504E01
1.375,0.073 1.75,0.333 0.375,0.26 1.865,0.073 2.24,0.333 0.375,0.26 2,0.135 2.313,0.333 0.313,0.198 10 false N1 1.5,0.146 1.813,0.344 0.313,0.198 10 false N2

Disconnect the N1 and N2 floor under wire from the NO. 1 EV battery junction block assembly.


c.
A483126C05
1.479,0.125 1.917,0.448 0.438,0.323 1.083,1.708 1.573,1.125 true 2.292,1.74 1.813,1.146 true 2.313,0.531 2.052,0.729 true 0.073,0.083 0.385,0.24 0.313,0.156 10 false *a 2.323,1.74 2.635,1.896 0.313,0.156 10 false CBI 0.865,1.75 1.177,1.906 0.313,0.156 10 false CEI 1.625,0.219 1.938,0.375 0.313,0.156 10 false N3 2.354,0.385 2.667,0.542 0.313,0.156 10 false *1
*1 Shield Ground
*a Floor Under Wire
(FC Converter Assembly Side)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(N3)Location & Routing

Click Connector(N3)Engine Compartment>Floor Under Wire>FC Converter Assembly

N3-1 (CEI) - N3-2 (CBI) Ignition switch off 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the N1 and N2 floor under wire.



OK

19.CHECK FC JUNCTION CABLE

NG

REPLACE FLOOR UNDER WIRE

19.CHECK FC JUNCTION CABLE
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A483165C01
0,0 0.313,0.198 0.313,0.198 10 true *A 0,2.458 0.313,2.656 0.313,0.198 10 true *B
*A for LHD
*B for RHD


Disconnect the FC junction cable from the inverter with converter assembly.


Procedure1

a.
A484671C01
0,2.438 0.313,2.635 0.313,0.198 10 true *B 0,0 0.313,0.198 0.313,0.198 10 true *A
*A for LHD
*B for RHD


Disconnect the FC junction cable from the FC converter assembly.

HINT:

Make sure that no foreign matter has entered or contaminated the FC junction cable.



b.
C257176C53
0.438,1.031 0.833,1.344 0.396,0.313 0.969,1.719 1.26,1.188 true 2.25,1.729 1.938,1.177 true 2.635,0.625 2.375,0.771 true 2.688,0.542 3,0.698 0.313,0.156 10 false *1 0.073,0.083 0.385,0.24 0.313,0.156 10 false *a 2.26,1.75 2.677,1.958 0.417,0.208 10 false 2 (N) 0.927,1.75 1.323,1.938 0.396,0.188 10 false 1 (P) 0.583,1.115 0.896,1.271 0.313,0.156 10 false x1
*1 Shield Ground
*a Front view of FC Junction Cable connector
(Inverter with Converter Assembly Side)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(x1)Location & Routing

Click Connector(x1)Engine Compartment>FC Junction Cable>Inverter with Converter Assembly

x1-1 (P) - x1-2 (N) Ignition switch off 10 kΩ or higher


NOTICE:

Be sure not to damage or deform the terminal being inspected.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the FC junction cable.



OK

7.CHECK FC CONVERTER ASSEMBLY

NG

REPLACE FC JUNCTION CABLE

20.REPLACE AIR CONDITIONING COMPRESSOR CABLE

NEXT

REPLACE FC COOLING WATER PUMP INVERTER ASSEMBLY AND FC HYDROGEN PUMP INVERTER ASSEMBLY

21.CHECK FRONT COMPARTMENT MAIN WIRE
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A483163C01
0.031,0 0.344,0.198 0.313,0.198 10 true *A 0.031,2.479 0.344,2.677 0.313,0.198 10 true *B
*A for LHD
*B for RHD


Disconnect the front compartment main wire connector from the inverter with converter assembly.

HINT:

Make sure that no foreign matter has entered or contaminated the front compartment main wire connector.



c.
A484673C01
0.021,0 0.333,0.198 0.313,0.198 10 true *A 0,2.51 0.313,2.708 0.313,0.198 10 true *B
*A for LHD
*B for RHD


Disconnect the No. 1 battery pack wire connector from the front compartment main wire.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>INVERTER WITH CONVERTER>REMOVAL



Procedure1

a.
A260188C73
0.635,1.198 1.031,1.49 0.396,0.292 1,1.76 1.531,1.531 true 2.396,1.729 1.917,1.531 true 2.344,0.896 2.115,0.938 true 2.396,0.802 2.708,0.958 0.313,0.156 10 false *1 0.135,0.104 0.448,0.26 0.313,0.156 10 false *a 0.719,1.271 1.031,1.427 0.313,0.156 10 false A32 0.635,1.698 1.125,1.927 0.49,0.229 10 false ACPE 2.438,1.698 2.927,1.927 0.49,0.229 10 false ACPB
*1 Shield Ground
*a Front Compartment Main Wire
(Inverter with Converter Assembly Side)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A32)Location & Routing

Click Connector(A32)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

A32-1 (ACPE) - A32-2 (ACPB) Ignition switch off 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the No. 1 battery pack wire connector.


b.

Reconnect the front compartment main wire connector.



OK

22.CHECK NO.1 BATTERY PACK WIRE

NG

REPLACE FRONT COMPARTMENT MAIN WIRE

22.CHECK NO.1 BATTERY PACK WIRE
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A484673C01
0.021,0 0.333,0.198 0.313,0.198 10 true *A 0,2.51 0.313,2.708 0.313,0.198 10 true *B
*A for LHD
*B for RHD


Disconnect the No. 1 battery pack wire connector from the front compartment main wire.

HINT:

Make sure that no foreign matter has entered or contaminated the front compartment main wire connector.



c.
A483173C01
0.021,0 0.333,0.198 0.313,0.198 10 true *A 0,2.51 0.313,2.708 0.313,0.198 10 true *B
*A for LHD
*B for RHD


Disconnect the No. 1 battery pack wire connector from the electric heater sub-assembly.


Procedure1

a.
C400224C03
0.281,0.885 0.698,1.229 0.417,0.344 1.031,1.771 1.5,1.188 true 2.5,1.76 2.031,1.167 true 1.938,1.375 1.771,1.76 1.771,1.76 1.625,1.375 true 0.417,0.99 0.729,1.188 0.313,0.198 10 false O4 0.896,1.823 1.354,2.021 0.458,0.198 10 false VOL- 2.51,1.854 2.969,2.052 0.458,0.198 10 false VOL+ 0.135,0.083 0.448,0.281 0.313,0.198 10 false *a 1.677,1.802 1.99,2 0.313,0.198 10 false *1
*1 Shield Ground
*a No. 1 battery pack wire
(Electric Heater Sub-assembly Side)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O4)Location & Routing

Click Connector(O4)Engine Compartment>EV Battery Pack Wire>Electric Heater Sub-Assembly

O4-1 (VOL-) - O4-2 (VOL+) Ignition switch off 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the No. 1 battery pack wire connector.



OK

REPLACE ELECTRIC HEATER SUB-ASSEMBLY

NG

REPLACE NO.1 BATTERY PACK WIRE

23.CHECK VEHICLE CONDITION
a.

Choose the model to be inspected.


Result:
Result Proceed to
Exept 1500W Type A
for 1500W Type B



A

REPLACE NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY

B

24.CHECK SOCKET INVERTER WIRE
24.CHECK SOCKET INVERTER WIRE
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
C384273

Disconnect the socket inverter wire from the NO.1 EV battery junction block assembly.

HINT:

Make sure that no foreign matter or water has entered the socket inverter wire connector.



Procedure1

a.
C384272C04
0.854,1.375 1.208,1.656 0.354,0.281 2.031,1.271 2.385,1.552 0.354,0.281 2.927,2.052 2.927,1.708 true 2.083,2.542 2.198,2.094 true 1.063,2.094 1.5,2.531 true 2.833,2.104 3.146,2.302 0.313,0.198 10 false *1 1.938,2.625 2.417,2.833 0.479,0.208 10 false CEP 1.438,2.625 1.844,2.813 0.406,0.188 10 false CBP 2.135,1.354 2.417,1.531 0.281,0.177 10 false P2 0.969,1.458 1.25,1.635 0.281,0.177 10 false P1 0.146,0.104 0.458,0.302 0.313,0.198 10 false *a
*1 Shield Ground
*a Socket Inverter Wire
(NO.1 EV Battery Junction Block Assembly Side)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(P1,P2)Location & Routing

P1-1 (CBP) - P2-1 (CEP) Ignition switch off 10 kΩ or higher


HINT:

Visually inspect the socket inverter wire for damage. If there is any damage, then this is the likely cause of low insulation resistance.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the socket inverter wire.



OK

REPLACE NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY

NG

25.CHECK SOCKET INVERTER WIRE
25.CHECK SOCKET INVERTER WIRE
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A479492

Disconnect the socket inverter wire from the voltage converter assembly.

HINT:

Make sure that no foreign matter or water has entered the FC battery charger wire connector.



c.
C384273

Disconnect the socket inverter wire from the No.1 EV battery junction block assembly.

HINT:

Make sure that no foreign matter or water has entered the FC battery charger wire connector.



Procedure1

a.
C384272C04
0.854,1.375 1.208,1.656 0.354,0.281 2.031,1.271 2.385,1.552 0.354,0.281 2.927,2.052 2.927,1.708 true 2.083,2.542 2.198,2.094 true 1.063,2.094 1.5,2.531 true 2.833,2.104 3.146,2.302 0.313,0.198 10 false *1 1.938,2.625 2.417,2.833 0.479,0.208 10 false CEP 1.438,2.625 1.844,2.813 0.406,0.188 10 false CBP 2.135,1.354 2.417,1.531 0.281,0.177 10 false P2 0.969,1.458 1.25,1.635 0.281,0.177 10 false P1 0.146,0.104 0.458,0.302 0.313,0.198 10 false *a
*1 Shield Ground
*a Socket Inverter Wire
(NO.1 EV Battery Junction Block Assembly Side)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(P1,P2)Location & Routing

P1-1 (CBP) - P2-1 (CEP) Ignition switch off 10 kΩ or higher


HINT:

Visually inspect the socket inverter wire for damage. If there is any damage, then this is the likely cause of low insulation resistance.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the socket inverter wire.



OK

NG

REPLACE SOCKET INVERTER WIRE