Home › BODY ELECTRICAL › AUDIO / VISUAL › AUDIO AND VISUAL SYSTEM

AUDIO AND VISUAL SYSTEM > PROBLEM SYMPTOMS TABLE

for Preparation Click here


HINT:
  1. Use the table below to help determine the cause of the problem symptom. The potential causes of the symptoms are listed in order of probability in the "Suspected area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.
  2. Inspect the fuses and relays related to this system before inspecting the suspected areas below.


Audio function 
Symptom
Suspected area
See page
Pressing power switch does not turn on system.
1. Proceed to "Pressing Power Switch does not Turn on System"
Click here
2. Radio receiver power source circuit
Click here
3. Multi-display power source circuit
Click here
4. AVC-LAN circuit
Click here
5. Radio receiver
Click here
6. Multi-display
Click here
Panel switch does not function.
1. Steering pad switch circuit
Click here
2. AVC-LAN circuit
Click here
3. Radio receiver
Click here
No sound can be heard from speakers (audio is mute).
1. AVC-LAN circuit
Click here
2. Radio receiver power source circuit
Click here
3. Multi-display power source circuit
Click here
4. Proceed to "No Sound can be Heard from Speakers"
Click here
5. Stereo component amplifier power source circuit
Click here
6. Proceed to "Sound Signal Circuit between Radio Receiver and Stereo Component Amplifier"
Click here
7. Speaker circuit
Click here
8. Proceed to "Mute Signal Circuit between Radio Receiver and Stereo Component Amplifier"
Click here
9. Stereo component amplifier
Click here
10. Radio receiver
Click here
11. Multi-display
Click here
Sound quality is bad in all modes (Volume is too low).
1. Proceed to "Poor Sound Quality in All Models (Low Volume)"
Click here
2. Speaker circuit
Click here
3. Proceed to !Sound Signal Circuit between Radio Receiver and Stereo Component Amplifier"
Click here
4. Proceed to "Mute Signal Circuit between Radio Receiver and Stereo Component Amplifier"
Click here
Auto sound levelizer does not function (9 speaker system).
Proceed to "Vehicle Speed Signal Circuit between Stereo Component Amplifier and Combination Meter"
Click here
Auto sound levelizer does not function (6 speaker system).
Proceed to "Vehicle Speed Signal Circuit between Radio Receiver and Combination Meter"
Click here
External device sound cannot be heard or sound quality is bad (Stereo jack is used).
1. Radio receiver power source circuit
Click here
2. Proceed to "Sound Signal Circuit between Radio Receiver and Stereo Jack Adapter"
Click here
3. Stereo jack adapter
-
4. Radio receiver
Click here
Abnormal noise occurs.
1. Proceed to "Noise occurs"
Click here
2. Stereo component amplifier
Click here
3. Radio receiver
Click here
Radio broadcast cannot be received or poor reception.
Proceed to "Radio Broadcast cannot be Received or Poor Reception"
Click here
CD cannot be inserted/played or CD is ejected right after insertion.
1. Radio receiver power source circuit
Click here
2. Proceed to "CD cannot be Inserted/Played or CD is Ejected Right After Insertion"
Click here
CD cannot be ejected.
1. Radio receiver power source circuit
Click here
2. Proceed to "CD cannot be Ejected"
Click here
Sound quality is bad only when CD is played.
Proceed to "Sound Quality is Bad Only when CD is Played (Volume is Too Low)"
Click here
CD sounds skips.
Proceed to "CD Sound Skips"
Click here
Radio receiver or multi-display cannot be illuminated at night.
Illumination circuit
Click here

Steering pad switch function 
Symptom
Suspected area
See page
Audio system cannot be operated with steering pad switch.
1. Steering pad switch circuit
Click here
2. Radio receiver
Click here
Steering pad switch cannot be illuminated at night.
Illumination circuit
Click here
Cellular phone registration failure, phone directory transfer failure.
Proceed to "Cellular Phone Registration Failure, Phone Directory Transfer Failure"
Click here
Cellular phone cannot send / receive.
1. Proceed to Cellular Phone cannot Send / Receive
Click here
2. Steering pad switch circuit
Click here
3. Multi-display
Click here
Cannot call in a certain place.
Proceed to "Cannot call in a Certain Place"
Click here
The other caller's voice cannot be heard, is too quiet, or distorted.
1. Proceed to "The Other Caller's Voice cannot be Heard, is too Quiet, or Distorted"
Click here
2. Multi-display
Click here
The other caller cannot hear your voice, or your voice is too quiet or distorted.
1. Proceed to "The Other Caller cannot Hear Your Voice, or Your Voice is too Quiet or Distorted"
Click here
2. Microphone circuit between overhead J/B and multi-display
Click here
3. Microphone
-
4. Microphone amplifier
-
5. Multi-display
Click here