1. PRECAUTION
The engine assembly with transmission is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop.
The vehicle has a hybrid system that operates at voltages up to 650 V. The hybrid system uses an HV battery that contains an electrolyte which is a strong alkali solution that includes potassium hydroxide. Be sure to follow the instructions in this manual to handle the system correctly. Failure to do so may result in serious injury or electrocution (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
2. DISCHARGE FUEL SYSTEM PRESSURE
G3834
3.REMOVE SERVICE PLUG GRIP
4.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
5.REMOVE FRONT WHEEL
51444A
6.REMOVE REAR ENGINE UNDER COVER LH
51443C
7.REMOVE REAR ENGINE UNDER COVER RH
52618A
8.REMOVE FRONT LOWER BUMPER ABSORBER
51441
9.REMOVE NO. 1 ENGINE UNDER COVER
51442E
10.REMOVE NO. 2 ENGINE UNDER COVER
11.DRAIN ENGINE OIL
12.DRAIN COOLANT (for Engine)
13.DRAIN COOLANT (for Inverter)
14.DRAIN HYBRID TRANSAXLE FLUID
11212
15.REMOVE NO. 2 CYLINDER HEAD COVER
Remove the 3 clips and No. 2 cylinder head cover.
Attempting to disengage both front and rear clips at the same time may cause the No. 2 cylinder cover to break.
Pull the No. 2 cylinder cover straight up to remove it. Attempting to pull the No. 2 cylinder cover forward may cause it to break.
53289A
16.REMOVE RADIATOR SUPPORT OPENING COVER
17705
17.REMOVE AIR CLEANER CAP SUB-ASSEMBLY
Disconnect the air flow meter connector.
Disconnect the 2 clamps and hose band, and remove the air cleaner cap sub-assembly.
Remove the air cleaner filter element.
17750A
18.REMOVE INLET AIR CLEANER ASSEMBLY
Remove the 2 bolts and inlet air cleaner assembly.
19.REMOVE AIR CLEANER CASE
Separate the 3 clamps and No. 4 water by-pass hose from the air cleaner case.
Remove the 3 bolts and air cleaner case.
20.REMOVE AIR CLEANER HOSE ASSEMBLY
G9214
21.REMOVE NO. 1 INVERTER BRACKET
82111
22.DISCONNECT ENGINE ROOM MAIN WIRE
G9221
23.REMOVE INVERTER COVER
24.CHECK TERMINAL VOLTAGE
82164
25.DISCONNECT FRAME WIRE
G2148
26.DISCONNECT GENERATOR CABLE
G1148
27.DISCONNECT MOTOR CABLE
82122
28.DISCONNECT NO. 2 ENGINE WIRE
G9221
29.INSTALL INVERTER COVER
82112
30.DISCONNECT NO. 2 ENGINE ROOM WIRE
G9228B
31.DISCONNECT WATER HOSE
G9200
32.REMOVE INVERTER WITH CONVERTER ASSEMBLY
G92A0A
33.REMOVE INVERTER RESERVE TANK ASSEMBLY
Remove the 2 bolts and inverter reserve tank assembly.
G9219A
34.REMOVE INVERTER TRAY BRACKET
Separate the 2 clamps.
Remove the 5 bolts and inverter tray bracket.
16571C
35.DISCONNECT NO. 1 RADIATOR HOSE
Slide the clamp and disconnect the No. 1 radiator hose from the radiator pipe.
16572D
36.DISCONNECT NO. 2 RADIATOR HOSE
Slide the clamp and disconnect the No. 2 radiator hose from the water inlet.
16281
37.DISCONNECT NO. 4 WATER BY-PASS HOSE
Slide the clamp and disconnect the No. 4 water by-pass hose from the radiator pipe.
G9227A
38.DISCONNECT NO. 3 INVERTER COOLING HOSE
Slide the clamp and disconnect the No. 3 inverter cooling hose from the hybrid vehicle transaxle assembly.
G9229A
39.DISCONNECT NO. 5 INVERTER COOLING HOSE
Slide the clamp and disconnect the No. 5 inverter cooling hose from the hybrid vehicle transaxle assembly.
87246A
40.DISCONNECT OUTLET HEATER WATER HOSE
Slide the clamp and disconnect the outlet heater water hose.
87245A
41.DISCONNECT INLET HEATER WATER HOSE
Slide the clamp and disconnect the inlet heater water hose.
42.DISCONNECT HEATER HOSE
Slide the clamp and disconnect the heater hose.
23826
43.DISCONNECT NO. 1 FUEL VAPOR FEED HOSE
Slide the clamp and disconnect the No. 1 fuel vapor feed hose.
23901
44.DISCONNECT FUEL TUBE SUB-ASSEMBLY
Release the claw and remove the No. 1 fuel pipe clamp.
Pinch the retainer as illustrated, then pull the fuel tube connector out of the pipe.
Remove any dirt and foreign matter from the fuel tube connector before performing this work.
Do not allow any scratches or foreign matter to get on the parts when disconnecting, as the fuel tube connector has the O-rings that seal the pipe.
Perform this work by hand. Do not use any tools.
Do not forcibly bend, kink or twist the nylon tube.
Protect the disconnected parts by covering them with plastic bags after disconnecting the fuel tube.
If the fuel tube connector and pipe are stuck, push and pull to release them.
88370
45.SEPARATE COMPRESSOR WITH MOTOR ASSEMBLY
82121
46.DISCONNECT ENGINE WIRE
Disconnect the 2 clamps.
Pull up the lever and disconnect the ECM connector.
Disconnect the 2 connectors, 2 clamps and engine wire from the engine room junction block.
Disconnect the 3 clamps.
Remove the bolt and disconnect the earth wire.
Disconnect the 2 clamps and engine wire.
47.SECURE STEERING WHEEL
45259A
48.REMOVE COLUMN HOLE COVER SILENCER SHEET (for LHD)
45260
49.SEPARATE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY (for LHD)
45025D
50.DISCONNECT NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY
51442A
51.REMOVE FRONT NO. 3 ENGINE UNDER COVER
57533B
52.REMOVE FRONT CENTER FLOOR BRACE
17410
53.REMOVE FRONT EXHAUST PIPE ASSEMBLY (w/ Exhaust Heat Recirculation System)
17410
54.REMOVE FRONT EXHAUST PIPE ASSEMBLY (w/o Exhaust Heat Recirculation System)
43502H
55.REMOVE FRONT AXLE SHAFT NUT LH
43501H
56.REMOVE FRONT AXLE SHAFT NUT RH
Perform the same procedure as for the LH side.
89543
57.SEPARATE FRONT SPEED SENSOR LH
89542
58.SEPARATE FRONT SPEED SENSOR RH
Perform the same procedure as for the LH side.
45047
59.SEPARATE TIE ROD END SUB-ASSEMBLY LH
45046
60.SEPARATE TIE ROD END SUB-ASSEMBLY RH
Perform the same procedure as for the LH side.
48810
61.SEPARATE FRONT STABILIZER LINK ASSEMBLY LH
48820B
62.SEPARATE FRONT STABILIZER LINK ASSEMBLY RH
Perform the same procedure as for the LH side.
48069
63.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH
48068
64.SEPARATE FRONT NO. 1 LOWER SUSPENSION ARM SUB-ASSEMBLY RH
Perform the same procedure as for the LH side.
43420
65.SEPARATE FRONT DRIVE SHAFT ASSEMBLY LH
43420
66.REMOVE FRONT DRIVE SHAFT ASSEMBLY LH
43410
67.SEPARATE FRONT DRIVE SHAFT ASSEMBLY RH
Perform the same procedure as for the LH side.
43410
68.REMOVE FRONT DRIVE SHAFT ASSEMBLY RH
Perform the same procedure as for the LH side.
43040B
69.REMOVE FRONT DRIVE SHAFT HOLE SNAP RING LH
43030B
70.REMOVE FRONT DRIVE SHAFT HOLE SNAP RING RH
Perform the same procedure as for the LH side.
51425A
71.REMOVE FRONT LOWER ENGINE MOUNTING BRACKET REINFORCEMENT
51108A
72.REMOVE REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY LH
51107A
73.REMOVE REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY RH
52258A
74.REMOVE FRONT SUSPENSION MEMBER REAR BRACE LH
52257
75.REMOVE FRONT SUSPENSION MEMBER REAR BRACE RH
Perform the same procedure as for the LH side.
51201
76.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
77.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE
Set an engine lifter.
Place the engine assembly on wooden blocks or equivalent so that the engine assembly is level.
Remove the 4 bolts and separate the front crossmember sub-assembly.
Remove the bolt and 2 nuts, and separate the engine mounting insulator sub-assembly RH.
Remove the bolt and nut, and separate the engine mounting insulator LH.
Carefully remove the engine assembly with transaxle from the vehicle.
Install the No. 1 engine hanger and No. 2 engine hanger with the 2 bolts.
| *1 | No. 1 Engine Hanger |
| *2 | No. 2 Engine Hanger |
| Part Name | Part No. |
|---|---|
| No. 1 engine hanger | 12281-37021 |
| No. 2 engine hanger | 12282-37011 |
| Bolt | 91552-81050 |
Attach an engine sling device and hang the engine assembly with a chain block.
57104E
78.REMOVE FRONT CROSSMEMBER SUB-ASSEMBLY
Remove the bolt and nut, and separate the front engine mounting insulator from the front engine mounting bracket.
12361A
79.REMOVE FRONT ENGINE MOUNTING INSULATOR
Perform this procedure only when replacement of the front engine mounting insulator is necessary.
Remove the 2 bolts and front engine mounting insulator.
12371A
80.REMOVE REAR ENGINE MOUNTING INSULATOR
Perform this procedure only when replacement of the rear engine mounting insulator is necessary.
Remove the through bolt and rear engine mounting insulator.
12372A
81.REMOVE ENGINE MOUNTING INSULATOR LH
Perform this procedure only when replacement of the engine mounting insulator LH is necessary.
Remove the 4 bolts and engine mounting insulator LH.
12305
82.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH
Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.
Remove the 2 bolts and 2 cooler brackets.
Disconnect the earth wire clamp from the engine mounting insulator sub-assembly RH.
Remove the 3 bolts and engine mounting insulator sub-assembly RH.
16577C
83.REMOVE RADIATOR PIPE
Slide the clamp and remove the No. 3 radiator hose from the cylinder head.
Remove the 2 bolts and radiator pipe.
28193
84.REMOVE STARTER HOLE INSULATOR
11363A
85.REMOVE FLYWHEEL HOUSING SIDE COVER
82121
86.REMOVE ENGINE WIRE
Disconnect all the wire harnesses and connectors. Make sure that no wire harnesses are connected to the engine assembly.
30900
87.REMOVE HYBRID VEHICLE TRANSAXLE ASSEMBLY
Remove the hybrid vehicle transaxle assembly (See page Drivetrain>P410 (HYBRID TRANSMISSION / TRANSAXLE)>HYBRID VEHICLE TRANSAXLE>REMOVAL).
Be careful not to apply excessive force to the transmission input damper assembly when removing or installing the hybrid vehicle transaxle assembly. If excessive force is applied, the transmission input damper assembly may be damaged, or its splines may become misaligned.
31270
88.REMOVE TRANSMISSION INPUT DAMPER ASSEMBLY
Gently place the engine assembly onto wood blocks or equivalent.
This step should be done while hanging the engine assembly using the engine hangers and a chain block.
Remove the transmission input damper assembly (See page Engine / Hybrid System>2ZR-FXE (ENGINE MECHANICAL)>REAR CRANKSHAFT OIL SEAL>REMOVAL).
13405
89.REMOVE FLYWHEEL SUB-ASSEMBLY
Remove the flywheel sub-assembly (See page Engine / Hybrid System>2ZR-FXE (ENGINE MECHANICAL)>REAR CRANKSHAFT OIL SEAL>REMOVAL).