Home › Drivetrain › P410 (HYBRID TRANSMISSION / TRANSAXLE) › HYBRID VEHICLE TRANSAXLE › 2013.08–2014.11
RM2070E _52 Drivetrain _061915 P410 HYBRID TRANSMISSION / TRANSAXLE _0301646 HYBRID VEHICLE TRANSAXLE A

P410 HYBRID TRANSMISSION / TRANSAXLE  HYBRID VEHICLE TRANSAXLE  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 53301 3.REMOVE HOOD SUB-ASSEMBLY

a.
C241666

Disconnect the clamp and washer hose.


b.

Remove the 4 bolts and hood sub-assembly from the hood hinge assembly RH and hood hinge assembly LH.


Hide 4.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 5.REMOVE FRONT WHEELS

Hide 51444A 6.REMOVE REAR ENGINE UNDER COVER LH

Hide 51443C 7.REMOVE REAR ENGINE UNDER COVER RH

Hide 52618A 8.REMOVE FRONT LOWER BUMPER ABSORBER

Hide 51441 9.REMOVE NO. 1 ENGINE UNDER COVER

Hide 51442E 10.REMOVE NO. 2 ENGINE UNDER COVER

Hide 14.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 55736D 15.REMOVE COWL BODY MOUNTING REINFORCEMENT LH (for LHD)

Hide 55735C 16.REMOVE COWL BODY MOUNTING REINFORCEMENT RH (for RHD)

Hide 55701J 17.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)

Hide 55701J 18.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)

Hide 17705 20.REMOVE AIR CLEANER CAP SUB-ASSEMBLY

Hide 53289A 24.REMOVE RADIATOR SUPPORT OPENING COVER

Hide G92A0A 37.REMOVE INVERTER RESERVE TANK ASSEMBLY

Hide G9227A 42.DISCONNECT NO. 3 INVERTER COOLING HOSE

Hide G9229A 43.DISCONNECT NO. 5 INVERTER COOLING HOSE

Hide G9228B 44.REMOVE WATER HOSE

a.
C236597

Disconnect the clamp from the wire harness clamp bracket.


b.

Disconnect the 2 hose clamps and remove the water hose.


Hide 45.DISCONNECT WIRE HARNESS

a.
A213036

Disconnect the 2 clamps.


b.

Pull up the lever and disconnect the connector of the ECM.


c.
C242242

Disconnect the 2 connectors and clamp from the engine room junction block and separate the wire harness.


d.
A240186

Disconnect the 2 clamps.


e.
A213039

Remove the bolt and disconnect the earth wire.


f.
C211188E01
1.03,2.36 1.173,2.15 1.173,2.15 1.267,2.15 false 1.287,2.057 1.458,2.220 0.172,0.163 10 *a

Release the green-colored lock and disconnect the connector as shown in the illustration.

CAUTION:

Wear insulated gloves when performing the procedure.


NOTICE:

Insulate the connector by sealing it with tape.


Text in Illustration
*a Green-colored Lock


g.
C211187

Disconnect the clamp and wire harness.


h.

Remove the 2 bolts and disconnect the 6 connectors and 12 wire harness clamps.

C236611


Hide 45259A 47.REMOVE COLUMN HOLE COVER SILENCER SHEET (for LHD)

Hide 45259A 48.REMOVE COLUMN HOLE COVER SILENCER SHEET (for RHD)

Hide 45260 49.SEPARATE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY (for LHD)

Hide 45260 50.SEPARATE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY (for RHD)

Hide 45025D 51.SEPARATE NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

Hide 17410 54.REMOVE FRONT EXHAUST PIPE ASSEMBLY (w/ Exhaust Heat Recirculation System)

Hide 17410 55.REMOVE FRONT EXHAUST PIPE ASSEMBLY (w/o Exhaust Heat Recirculation System)

Hide 43501H 57.REMOVE FRONT AXLE SHAFT NUT RH

HINT:

Perform the same procedure as for the LH side.


Hide 89543 58.SEPARATE FRONT SPEED SENSOR LH

Hide 89542 59.SEPARATE FRONT SPEED SENSOR RH

HINT:

Perform the same procedure as for the LH side.


Hide 45047 60.SEPARATE TIE ROD END SUB-ASSEMBLY LH

Hide 45046 61.SEPARATE TIE ROD END SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48810 62.SEPARATE FRONT STABILIZER LINK ASSEMBLY LH

Hide 48820B 63.SEPARATE FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48069 64.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

Hide 48068 65.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 43420 66.SEPARATE FRONT DRIVE SHAFT ASSEMBLY LH

Hide 43410 68.SEPARATE FRONT DRIVE SHAFT ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 43410 69.REMOVE FRONT DRIVE SHAFT ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 43420G 70.REMOVE FRONT DRIVE SHAFT HOLE SNAP RING LH

Hide 43410N 71.REMOVE FRONT DRIVE SHAFT HOLE SNAP RING RH

HINT:

Perform the same procedure as for the LH side.


Hide 72.INSTALL ENGINE HANGERS

a.
A214905

Install the 2 engine hangers with the 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

Part Name Part No.
No. 1 Engine Hanger 12281-37021
No. 2 Engine Hanger 12282-37011
Bolt 91552-81050


b.

Attach a sling device to the engine hangers and a chain block.


Hide 28193 73.REMOVE STARTER HOLE INSULATOR

a.
C209282

Remove the 2 bolts and starter hole insulator from the engine.


Hide 11363A 74.REMOVE FLYWHEEL HOUSING SIDE COVER

a.
C209283

Remove the flywheel housing side cover from the engine.


Hide 51425A 75.REMOVE FRONT ENGINE MOUNTING BRACKET LOWER REINFORCEMENT

Hide 51108A 76.REMOVE REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY LH

Hide 51107A 77.REMOVE REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 52258A 78.REMOVE FRONT SUSPENSION MEMBER REAR BRACE LH

Hide 52257 79.REMOVE FRONT SUSPENSION MEMBER REAR BRACE RH

HINT:

Perform the same procedure as for the LH side.


Hide 51201 80.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

Hide 12371A 81.REMOVE REAR ENGINE MOUNTING INSULATOR

Hide 30900 82.SUPPORT HYBRID VEHICLE TRANSAXLE ASSEMBLY

a.

Support the hybrid vehicle transaxle assembly with a transmission jack.


Hide 57104E 83.REMOVE FRONT CROSSMEMBER SUB-ASSEMBLY

a.
A213041

Remove the bolt and nut from the front engine mounting insulator.


b.
A213042

Remove the 4 bolts and front crossmember sub-assembly from the body.


Hide 12361A 84.REMOVE FRONT ENGINE MOUNTING INSULATOR

Hide 12325A 85.REMOVE ENGINE MOUNTING BRACKET LH

a.
A248101

Remove the bolt and nut, and separate the engine mounting insulator LH.

NOTICE:

Turn the nut while holding the bolt.



b.
C209289

Remove the 3 bolts and engine mounting bracket LH from the hybrid vehicle transaxle assembly.


Hide 30900 86.REMOVE HYBRID VEHICLE TRANSAXLE ASSEMBLY

a.
C209286

Remove the 7 bolts and hybrid vehicle transaxle assembly from the engine.

NOTICE:
·

To avoid damage to the knock pins, do not pry between the hybrid vehicle transaxle assembly and the engine.

·

To prevent the splines of the transmission input damper from becoming misaligned, do not allow the hybrid vehicle transaxle assembly to hit the transmission input damper during hybrid vehicle transaxle assembly removal and installation.




Hide 12311A 87.REMOVE FRONT ENGINE MOUNTING BRACKET

a.
C209287

Remove the 3 bolts and front engine mounting bracket from the hybrid vehicle transaxle assembly.


Hide 12321A 88.REMOVE REAR ENGINE MOUNTING BRACKET

a.
C209288

Remove the 4 bolts and rear engine mounting bracket from the hybrid vehicle transaxle assembly.


Hide 91.REMOVE WIRE HARNESS CLAMP BRACKET

a.
C236612

Remove the 2 bolts and 2 wire harness clamp brackets from the hybrid vehicle transaxle assembly.


Hide G1143 92.REMOVE MOTOR CABLE BRACKET

a.
C210345

Remove the bolt and motor cable bracket from the hybrid vehicle transaxle assembly.