Home › Drivetrain › P410 (HYBRID TRANSMISSION / TRANSAXLE) › HYBRID VEHICLE TRANSAXLE › 2012.10–2013.08
RM2070E _52 Drivetrain _061915 P410 HYBRID TRANSMISSION / TRANSAXLE _0301646 HYBRID VEHICLE TRANSAXLE A

P410 HYBRID TRANSMISSION / TRANSAXLE  HYBRID VEHICLE TRANSAXLE  INSTALLATION  


PROCEDURE

Hide G1143 1.INSTALL MOTOR CABLE BRACKET

a.

Install the motor cable bracket to the hybrid vehicle transaxle assembly with the bolt.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)


Hide 2.INSTALL WIRE HARNESS CLAMP BRACKET

a.
C236612E03
1.271,3.927 1.406,4.083 0.135,0.156 10 true B 2.01,0.552 2.177,0.75 0.167,0.198 10 true A

Install the 2 wire harness clamp brackets to the hybrid vehicle transaxle assembly with the 2 bolts.

Torque:
Bolt A : 29 N*m (296 kgf*cm, 21 ft.*lbf)
Bolt B : 23 N*m (235 kgf*cm, 17 ft.*lbf)


Hide 12321A 5.INSTALL REAR ENGINE MOUNTING BRACKET

a.
C209288E04
2.521,0.76 2.635,0.927 0.115,0.167 10 false A 2.552,1.365 2.667,1.531 0.115,0.167 10 false B 2.563,1.708 2.677,1.875 0.115,0.167 10 false C 1.365,1.302 1.479,1.469 0.115,0.167 10 true D

Install the rear engine mounting bracket with the 4 bolts in several steps.

Torque:
45 N*m (459 kgf*cm, 33 ft.*lbf)

NOTICE:

Temporarily tighten bolt A, and then fully tighten the 4 bolts in the order of C, B, D and A.



Hide 12311A 6.INSTALL FRONT ENGINE MOUNTING BRACKET

a.
C209287E04
1.302,0.177 1.469,0.365 0.167,0.188 10 true A 1.167,1.646 1.292,1.813 0.125,0.167 10 false B 1.615,0.219 1.76,0.396 0.146,0.177 10 true C

Install the front engine mounting bracket with the 3 bolts in several steps.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)

NOTICE:

Temporarily tighten bolt A, and then fully tighten the 3 bolts in the order of B, C and A.



Hide 30900 7.SUPPORT HYBRID VEHICLE TRANSAXLE ASSEMBLY

a.

Support the hybrid vehicle transaxle assembly with a transmission jack.


Hide 30900 8.INSTALL HYBRID VEHICLE TRANSAXLE ASSEMBLY

a.
C209284E04
1.219,0.51 2.969,0.25 2.969,0.25 2.635,0.688 false 3,0.167 3.177,0.333 0.177,0.167 10 false *1 1.104,2.542 1.24,2.719 0.135,0.177 10 false A 2.135,2.469 2.271,2.646 0.135,0.177 10 false B 2.49,4.229 2.625,4.406 0.135,0.177 10 true C 2.042,4.469 2.177,4.646 0.135,0.177 10 false C 1.594,4.458 1.729,4.635 0.135,0.177 10 false C 1.052,4.302 1.188,4.479 0.135,0.177 10 true C 0.729,3.354 0.865,3.531 0.135,0.177 10 true C

Make sure that the knock pins are installed to the engine.

Text in Illustration
*1 Knock Pin


b.

Using an transmission jack, align the engine assembly and hybrid vehicle transaxle assembly, fit the knock pins into the knock pin holes, and tighten the 7 bolts shown in the illustration.

Torque:
33 N*m (337 kgf*cm, 24 ft.*lbf)

NOTICE:
·

Make sure to align the hybrid vehicle transaxle assembly so that the input shaft of the hybrid vehicle transaxle assembly will be inserted straight into the inner splines of the transmission input damper.

·

When inserting the input shaft of the hybrid vehicle transaxle assembly into the inner splines of the transmission input damper, do not shake the hybrid vehicle transaxle excessively.

·

When mounting the hybrid vehicle transaxle assembly to the engine, make sure to securely fit the knock pins into the knock holes.

·

Push in the hybrid vehicle transaxle assembly so that the contact surfaces of the engine and the hybrid vehicle transaxle assembly are aligned evenly.

·

While mounting the hybrid vehicle transaxle assembly to the engine assembly, temporarily tighten the bolt (A), and then fully tighten the 3 bolts in the order of B, A and C.

·

Do not hang the hybrid vehicle transaxle assembly off of the engine if the contact surfaces of the engine and the hybrid vehicle transaxle assembly are not in full contact. The knock holes of the hybrid vehicle transaxle case may be deformed due to the excessive weight of the engine and hybrid vehicle transaxle assembly, resulting in misalignment between the engine and hybrid vehicle transaxle assembly.




Hide 12325A 9.INSTALL ENGINE MOUNTING BRACKET LH

a.
C209289E04
2.031,1.563 2.167,1.76 0.135,0.198 10 true B 0.792,0.521 0.917,0.677 0.125,0.156 10 false C 2.198,1 2.344,1.177 0.146,0.177 10 true A

Install the engine mounting bracket LH with 3 new bolts in several steps.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)

NOTICE:

Temporarily tighten bolt A, and then fully tighten the 3 bolts in the order of B, C and A.



b.

Install the engine mounting insulator LH with the bolt and nut.

Torque:
56 N*m (571 kgf*cm, 41 ft.*lbf)

NOTICE:

When installing the engine mounting insulator, tighten the nut while holding the bolt.



Hide 51201 11.INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

Hide 57104E 13.INSTALL FRONT CROSSMEMBER SUB-ASSEMBLY

a.

Install the front crossmember to the body with the 4 bolts.

Torque:
96 N*m (979 kgf*cm, 71 ft.*lbf)


b.

Install the front engine mounting insulator to the front crossmember with the 2 bolts.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)


c.

Tighten the front engine mounting insulator with the bolt and nut.

Torque:
145 N*m (1479 kgf*cm, 107 ft.*lbf)


Hide 52258A 14.INSTALL FRONT SUSPENSION MEMBER REAR BRACE LH

Hide 52257 15.INSTALL FRONT SUSPENSION MEMBER REAR BRACE RH

HINT:

Perform the same procedure as for the LH side.


Hide 51108A 16.INSTALL REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY LH

Hide 51107A 17.INSTALL REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 51425A 18.INSTALL FRONT ENGINE MOUNTING BRACKET LOWER REINFORCEMENT

Hide 11363A 19.INSTALL FLYWHEEL HOUSING SIDE COVER

a.

Install the flywheel housing side cover.


Hide 28193 20.INSTALL STARTER HOLE INSULATOR

a.

Install the starter hole insulator with the 2 bolts.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


Hide 21.REMOVE ENGINE HANGERS

a.

Remove the 2 bolts, No. 1 engine hanger and No. 2 engine hanger.


Hide 43040B 22.INSTALL FRONT DRIVE SHAFT HOLE SNAP RING LH

Hide 43030B 23.INSTALL FRONT DRIVE SHAFT HOLE SNAP RING RH

HINT:

Perform the same procedure as for the LH side.


Hide 43410 25.INSTALL FRONT DRIVE SHAFT ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48069 26.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

Hide 48068 27.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48810 28.INSTALL FRONT STABILIZER LINK ASSEMBLY LH

Hide 48820B 29.INSTALL FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 45047 30.CONNECT TIE ROD END SUB-ASSEMBLY LH

Hide 45046 31.CONNECT TIE ROD END SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 89543 32.INSTALL FRONT SPEED SENSOR LH

Hide 89542 33.INSTALL FRONT SPEED SENSOR RH

HINT:

Perform the same procedure as for the LH side.


Hide 43501H 35.INSTALL FRONT AXLE SHAFT NUT RH

HINT:

Perform the same procedure as for the LH side.


Hide 17410 36.INSTALL FRONT EXHAUST PIPE ASSEMBLY (w/ Exhaust Heat Recirculation System)

Hide 17410 37.INSTALL FRONT EXHAUST PIPE ASSEMBLY (w/o Exhaust Heat Recirculation System)

Hide 45025D 40.CONNECT NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

Hide 45260 41.CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY (for LHD)

Hide 45260 42.CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY (for RHD)

Hide 43. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 45259A 44.INSTALL COLUMN HOLE COVER SILENCER SHEET (for LHD)

Hide 45259A 45.INSTALL COLUMN HOLE COVER SILENCER SHEET (for RHD)

Hide 46.INSTALL WIRE HARNESS

a.

Connect the 12 wire harness clamps and 6 connectors and install the 2 bolts.

Torque:
8.4 N*m (85 kgf*cm, 74 in.*lbf)


b.

Connect the wire harness with the clamp.


c.
C235091E04
2.634,2.372 2.699,2.088 2.699,2.088 2.777,2.088 false 2.815,2.002 3.017,2.164 0.202,0.162 10 *a

Connect the connector and lock the green-colored lock as shown in the illustration.

CAUTION:

Wear insulated gloves when performing the procedure.


Text in Illustration
*a Green-colored Lock


d.

Install the earth wire with the bolt.

Torque:
8.4 N*m (85 kgf*cm, 74 in.*lbf)


e.

Connect the wire harness 2 clamps to the engine room junction block.


f.

Connect the 2 connectors to the engine room junction block.


g.

Connect the connector to the ECM with the lock lever.


h.

Connect the 2 clamps.


Hide G9228B 47.INSTALL WATER HOSE

a.

Install the water hose to the hybrid vehicle transaxle assembly with the 2 hose clamps.

C351653E01
2.854,4.281 2.958,4.281 2.958,4.281 3.083,4.042 false 4.677,3.917 4.74,3.698 4.74,3.698 4.865,3.698 false 4.333,4.625 4.198,4.625 4.198,4.625 4.125,4.354 false 4.74,4.563 4.604,4.563 4.604,4.563 4.531,4.344 false 4,0.333 4.063,0.24 4.063,0.24 4.188,0.24 false 3.49,0.323 3.427,0.219 3.427,0.219 3.292,0.219 false 3.375,0.854 3.531,0.854 3.531,0.854 3.677,0.667 false 3.719,0.542 3.656,0.458 3.656,0.458 3.552,0.458 false 3.135,0.146 3.417,0.396 0.281,0.25 10 false *d 3.385,0.385 3.667,0.635 0.281,0.25 10 false *b 3.198,0.76 3.479,1.01 0.281,0.25 10 false *c 3.885,3.5 4.167,3.75 0.281,0.25 10 false *a 4.896,3.604 5.177,3.854 0.281,0.25 10 false *1 4.365,4.542 4.646,4.792 0.281,0.25 10 false *2 4.771,4.479 5.052,4.729 0.281,0.25 10 false *3 2.667,4.188 2.948,4.438 0.281,0.25 10 false *e 3.083,4.365 3.365,4.615 0.281,0.25 10 false *f 4.229,0.188 4.51,0.438 0.281,0.25 10 false *d

Text in Illustration
*1 Water Hose
*2 No. 2 Motor Water Jacket Cover Assembly
*3 Hose Clamp
*a 2 to 7 mm (0.0787 to 0.276 in.)
*b Alignment Mark
*c Yellow Mark
*d Within 45° of the center of the clamp claw
*e Green Mark
*f Downward

NOTICE:
·

Align the yellow mark of the water hose and the alignment mark of the No. 2 motor water jacket cover assembly.

·

Install the water hose upper clamp so that the center of the clamp claws is within 45° of the center of the matchmark of the No. 2 motor water jacket cover assembly as shown in the illustration.

·

Install the water hose so that the green mark of the water hose is within 15° of facing downward.




b.

Connect the clamp to the wire harness clamp bracket.


Hide 55701J 72.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)

Hide 55701J 73.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)

Hide 55736D 74.INSTALL COWL BODY MOUNTING REINFORCEMENT LH (for LHD)

Hide 55735C 75.INSTALL COWL BODY MOUNTING REINFORCEMENT RH (for RHD)

Hide 76.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 81.INSPECT FOR HYBRID TRANSAXLE FLUID LEAK

Hide 84.INSPECT FOR EXHAUST GAS LEAK

Hide 51441 85.INSTALL NO. 1 ENGINE UNDER COVER

Hide 51442E 86.INSTALL NO. 2 ENGINE UNDER COVER

Hide 52618A 87.INSTALL FRONT LOWER BUMPER ABSORBER

Hide 51444A 88.INSTALL REAR ENGINE UNDER COVER LH

Hide 51443C 89.INSTALL REAR ENGINE UNDER COVER RH

Hide 53301 91.INSTALL HOOD SUB-ASSEMBLY

a.

Install the hood sub-assembly to the hood hinge assembly RH and hood hinge assembly LH with the 4 bolts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


b.

Connect the clamp and washer hose.


Hide 53301 93.ADJUST HOOD SUB-ASSEMBLY

Hide 53289A 94.INSTALL RADIATOR SUPPORT OPENING COVER

Hide 96.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT