Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING UNIT › from 2016.08
RM3210E _58 Vehicle Interior _047534 HEATING / AIR CONDITIONING _0230753 AIR CONDITIONING UNIT A

HEATING / AIR CONDITIONING  AIR CONDITIONING UNIT  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during air conditioning unit removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Intelligent clearance sonar system*1
Simple intelligent parking assist system*1
Pre-crash safety system
Parking assist monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)
·

No. 1 air conditioning radiator damper servo sub-assembly

·

No. 2 air conditioning radiator damper servo sub-assembly

·

No. 3 air conditioning radiator damper servo sub-assembly


Initialize servo motor (Air conditioning system) DTCs are stored (Click here)

*1: When performing learning using the GTS.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT CLEARANCE SONAR SYSTEM>CALIBRATION

PROCEDURE

Hide 1. PRECAUTION

NOTICE:
·

Make sure to select face mode before disconnecting the cable from the negative (-) auxiliary battery terminal.

·

Make sure to perform initialization after replacing the air conditioning radiator damper servo sub-assembly. If initialization is not performed, the air conditioner unit assembly will not perform properly as the air conditioning amplifier assembly will not be able to recognize the position of the air conditioning radiator damper sub-assembly.



Hide 2. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Hide 3.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 55737B 4.REMOVE NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL (for LHD)

Hide 55738D 5.REMOVE NO. 2 HEATER AIR DUCT SPLASH SHIELD SEAL (for RHD)

Hide 55735A 6.REMOVE WATER GUARD PLATE LH

Hide 55736D 7.REMOVE COWL BODY MOUNTING REINFORCEMENT LH

Hide 55701J 8.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 87246A 9.DISCONNECT OUTLET HEATER WATER HOSE A (w/o Exhaust Heat Recirculation System)

a.
E336815

Using pliers, grip the claws of the clip and slide the clip to disconnect the outlet heater water hose A.

NOTICE:
·

Do not apply excessive force to the outlet heater water hose A.

·

Prepare a drain pan or cloth in case the coolant leaks.




Hide 87207A 10.DISCONNECT WATER PIPE AND HOSE SUB-ASSEMBLY A (w/ Exhaust Heat Recirculation System)

a.
E336814

Using pliers, grip the claws of the clip and slide the clip to disconnect the water pipe and hose sub-assembly A.

NOTICE:
·

Do not apply excessive force to the water pipe and hose sub-assembly A.

·

Prepare a drain pan or cloth in case the coolant leaks.




Hide 87245A 11.DISCONNECT INLET HEATER WATER HOSE A

a.

w/o Exhaust Heat Recirculation System:

i.
E336818

Using pliers, grip the claws of the clip and slide the clip to disconnect the inlet heater water hose A.

NOTICE:
·

Do not apply excessive force to the inlet heater water hose A.

·

Prepare a drain pan or cloth in case the coolant leaks.





b.

w/ Exhaust Heat Recirculation System:

i.
E336819

Using pliers, grip the claws of the clip and slide the clip to disconnect the inlet heater water hose A.

NOTICE:
·

Do not apply excessive force to the inlet heater water hose A.

·

Prepare a drain pan or cloth in case the coolant leaks.





Hide 88707 12.DISCONNECT SUCTION PIPE SUB-ASSEMBLY

a.
E336830

Remove the bolt and rotate the hook connector as shown in the illustration.


b.
E336833

Disconnect the suction pipe sub-assembly.


c.

Remove the O-ring from the suction pipe sub-assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



Hide 88710E 13.DISCONNECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY

a.
E336835

Disconnect the air conditioner tube and accessory assembly.


b.

Remove the O-ring from the air conditioner tube and accessory assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



Hide 14.REMOVE FRONT SEAT ASSEMBLY LH

Hide 15.REMOVE FRONT SEAT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>REMOVAL


Hide 16.REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY

Hide 17.REMOVE STEERING COLUMN ASSEMBLY

Hide 86652F 18.REMOVE SKID CONTROL BUZZER (w/ Toyota Safety Sense P)

Hide 88150A 19.REMOVE DRIVING SUPPORT ECU ASSEMBLY (w/ Toyota Safety Sense P)

Hide 85940 20.REMOVE WINDSHIELD WIPER RELAY ASSEMBLY (w/ Rain Sensor)

Hide 89343C 21.REMOVE NO. 1 CLEARANCE WARNING BUZZER (w/ TOYOTA Parking Assist-sensor System)

Hide 89343D 22.REMOVE NO. 2 CLEARANCE WARNING BUZZER (w/ TOYOTA Parking Assist-sensor System)

Hide 89340A 23.REMOVE CLEARANCE WARNING ECU ASSEMBLY (w/ TOYOTA Parking Assist-sensor System)

Hide 85970A 24.REMOVE DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY (w/ Double Locking System)

Hide 82877 25.REMOVE ECU INTEGRATION BOX RH (for LHD)

Hide 82878 26.REMOVE ECU INTEGRATION BOX LH (for RHD)

Hide 27.REMOVE TELEMATICS TRANSCEIVER WITH ANTENNA CORD (w/ Telematics Transceiver)

Hide 33560 28.REMOVE SHIFT LOCK CONTROL UNIT ASSEMBLY

Hide 88625Q 29.REMOVE COOLER (ROOM TEMP. SENSOR) THERMISTOR

a.
E336849

Disconnect the connector and aspirator to remove the cooler (room temp. sensor) thermistor.


Hide 58816C 30.REMOVE FRONT NO. 1 CONSOLE BOX INSERT

a.
E337307C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Disengage the clip and claw as shown in the illustration.


b.
E340368C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the guide to remove the front No. 1 console box insert as shown in the illustration.


Hide 58817B 31.REMOVE FRONT NO. 2 CONSOLE BOX INSERT

a.
E337302C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Disengage the clip and claw as shown in the illustration.


b.
E340366C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the guide to remove the front No. 2 console box insert as shown in the illustration.


Hide 58569D 32.REMOVE FRONT FLOOR CAUTION PLATE COVER

a.
E350285C02
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Disengage the claw and guide as shown by the arrow (1), and then pull the front floor caution plate cover as shown by the arrow (2) in the illustration to remove it.


Hide 87212G 33.REMOVE REAR NO. 3 AIR DUCT

a.
E341464

Remove the 2 front floor carpet clips.


b.
E337312

Disengage the 2 guides and turn back the front floor carpet assembly as shown in the illustration.


c.
E341465C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 claws to remove the rear No. 3 air duct as shown in the illustration.


Hide 87212F 34.REMOVE REAR NO. 2 AIR DUCT

a.
E337325

Disengage the 2 claws and remove the rear No. 2 air duct.


Hide 87212J 35.REMOVE REAR NO. 5 AIR DUCT

a.
E341463

Remove the 2 front floor carpet clips.


b.
E337319

Disengage the 2 guides and turn back the front floor carpet assembly as shown in the illustration.


c.
E341466C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 claws to remove the rear No. 5 air duct as shown in the illustration.


Hide 87212H 36.REMOVE REAR NO. 4 AIR DUCT

a.
E337335

Disengage the 2 claws and remove the rear No. 4 air duct.


Hide 87212 37.REMOVE REAR NO. 1 AIR DUCT

a.
E337338

Disengage the 4 claws to remove the rear No. 1 air duct.


Hide 55215D 38.REMOVE NO. 3 DASH PANEL INSULATOR PAD

a.
E341822

Disengage the 2 clips to remove the No. 3 dash panel insulator pad.


Hide 55306A 39.REMOVE NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.
E339401

Turn back the front floor mat as shown in the illustration.


b.
E339402

Disengage each clamp.


c.

Remove the bolt and disconnect the earth wire.


d.

w/ PTC Heater:

i.
E339409

Remove the bolt and disconnect the earth wire.



e.
E339408C01
0,0 0,0 false
V100135

Bolt
V100136

Screw
V100137

Nut


Remove the bolt, screw, nut and No. 1 instrument panel brace sub-assembly.


Hide 55307C 40.REMOVE NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.
E339410

Turn back the front floor mat as shown in the illustration.


b.
E339411

Disengage each clamp.


c.
E339412C01
0,0 0,0 false
V100135

Bolt
V100136

Screw
V100137

Nut


Remove the bolt, screw, nut and No. 2 instrument panel brace sub-assembly.


Hide 55308B 41.REMOVE NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY

a.

for LHD:

i.
E339413C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Disengage the clamp and 2 claws to disconnect the DLC3 connector.



b.

Remove the bolt, nut and No. 3 instrument panel to cowl brace sub-assembly.


Hide 42.REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU

Hide 55990B 43.REMOVE LOWER DEFROSTER NOZZLE ASSEMBLY

a.
E338066

Disengage the 6 claws to remove the lower defroster nozzle assembly.


Hide 44.REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONER UNIT ASSEMBLY

NOTICE:
·

Be sure to support the air conditioner unit assembly when removing it. Failure to do so may cause the bracket of the air conditioner unit assembly to break.

·

When disassembling the air conditioner unit assembly, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.



a.

for LHD:

i.

Disconnect each connector.

E340724C01
1.854,4.719 1.979,4.99 true 0.729,4.75 0.906,4.927 true 4.969,1.073 4.969,0.677 true 2.385,5.135 2.729,5.573 true 5.729,2.479 6.021,2.719 0.292,0.24 12 true *A 4.906,1.083 5.167,1.302 0.26,0.219 10 false *a 0.531,4.635 0.74,4.844 0.208,0.208 10 true *b 2.74,5.479 3,5.698 0.26,0.219 10 true *a 1.677,4.615 1.865,4.865 0.188,0.25 10 true *a
*A w/ PTC Heater - -
*a Earth Wire *b Relay Block Assembly
V100135

Connector
V100136

Bolt



ii.

Remove the 3 bolts and disconnect the 3 earth wires.


iii.

Remove the bolt and disconnect the relay block assembly.


iv.

Disengage each clamp and disconnect the instrument panel wire.



b.

for RHD:

i.

Disconnect each connector.

E338064C01
4.708,0.708 5.177,0.917 5.177,0.917 4.927,0.719 true 6.615,0.49 6.865,0.406 true 0.75,4.615 1.052,5.219 true 5.208,0.833 5.396,1.01 0.188,0.177 10 true *a 6.875,0.302 7.083,0.479 0.208,0.177 10 true *b 0.563,4.521 0.75,4.698 0.188,0.177 10 true *a
*a Earth Wire *b Relay Block Assembly
V100135

Connector
V100136

Bolt



ii.

Remove the 3 bolts and disconnect the 3 earth wires.


iii.

Remove the bolt and disconnect the relay block assembly.


iv.

Disengage each clamp and disconnect the instrument panel wire.



c.
E339611C01
0.458,3.021 0.958,2.76 true 0.292,2.938 0.542,3.125 0.25,0.188 10 true *1
*1 COOLER UNIT DRAIN HOSE GROMMET


Disconnect the drain cooler hose.

NOTICE:

If the cooler unit drain hose grommet is disconnected from the vehicle body while disconnecting the drain cooler hose, make sure to replace it with a new one. Failure to do so may cause water ingress.



d.
E338059

Remove the 2 bolts.


e.

Remove the 4 bolts (A).

E339607C01
0,0 0,0 false
V100135

Bolt (A)
V100136

Bolt (B)
V100137

Nut - -



f.

Remove the bolt (B) and disconnect the parking brake pedal assembly.


g.

Remove the nut.


h.

Disconnect each connector.

E339605C01
0,0 0,0 false
V113147

Remove in this Direction - -



i.

Remove the instrument panel reinforcement assembly with air conditioner unit assembly as shown in the illustration.


Hide 45.REMOVE AIR CONDITIONER UNIT ASSEMBLY

a.

Remove the 3 bolts and air conditioner unit assembly from the instrument panel reinforcement assembly.

E339608