Home › Engine / Hybrid System › B58 (ENGINE MECHANICAL) › PISTON › 2019.03–2020.03
RM3650E _51 Engine / Hybrid System _080179 B58 ENGINE MECHANICAL _0388916 PISTON A

B58 ENGINE MECHANICAL  PISTON  INSTALLATION  


PROCEDURE

Hide 1.INSTALL PISTON RING

CAUTION:
·

Very wide spreading of the piston rings during installation / removal.

·

Damage to the piston rings.

-

Spread the piston rings only until the piston ring can just be slid over the piston.

-

Use piston ring pliers to install and remove the piston rings.


·

Clean the used pistons carefully. Do not use a metal-cutting tool to avoid damaging the pistons.

·

Wear safety goggles.



NOTICE:

The description is for one component only. The procedure is identical for all further components.


a.
A513584

Keep the standard piston ring pliers (1) ready.


b.
A513595

Correctly prepare the piston rings:

i.

Upper piston ring (1): Plain rectangular compression ring (engraving must point upwards)


ii.

Centre piston ring (2): Taper faced piston ring (engraving must point upwards)


iii.

Oil scraper ring (3): consists of 2 piston rings ((O1), (O3)) with a spring (O2) in the centre.



c.
A513598

Make sure that the assembly mark TOP (1) points to the top to the combustion chamber.


d.

If there is no assembly mark TOP (1), then the piston ring with the writing must point to the top to the combustion chamber.


e.
A513588

Attach the oil scraper rings (1) and springs (2) manually (see following steps).


f.
A513590

Slide the spring (1) on to the piston (2) and install it.


g.
A513589

Slide the two oil scraper rings (1) on to the piston (2) and install them.


h.
A513599

Position the centre piston ring (1) in the marked area at the piston ring pliers (2).


i.
A513587

Clamp the piston ring pliers (1) in the direction of arrow and feed in the centre piston ring (2) in the piston (3) and install it.


j.
A513600

Release the piston ring pliers (1) at the centre piston ring (2).


k.

Feed out the piston ring pliers (1) at the centre piston ring (2) and remove it.


l.
A513599

Position the upper piston ring (1) in the marked area at the piston ring pliers (2).


m.
A513586

Clamp the piston ring pliers (1) in the direction of arrow and feed in the upper piston ring (2) in the piston (3) and install it.


n.
A513585

Release the piston ring pliers (1) at the upper piston ring (2).


o.

Feed out the piston ring pliers (1) at the upper piston ring (2) and remove it.


Hide 2.INSTALL PISTON

a.
A441689

Install piston pin (1) in piston (2) and connecting rod (3).

HINT:

Piston and piston pin are matched to each other.

Always install piston and piston pin together and do not switch by mistake.



b.
A441456

Position the piston pin hole snap ring (1) such that the opening in the marked area of the piston pin hole snap ring points in the direction of the piston top side (2).

CAUTION:
·

Piston pin hole snap ring with preload.

Danger of injury!

-

The use of the specified special tool for the disassembly or installation is mandatory.

-

Wear safety goggles.





c.
A442082

Preload the piston pin hole snap ring (1) using your thumb.


d.

Simultaneously press the piston pin hole snap ring into the piston using special tools 2 410 685 and 2 463 754.

SST
09200-WA580  
09200-WA750  


e.

Twist and reposition special tool 2 410 685 and completely press the piston pin hole snap ring into the piston.

SST
09200-WA580  


f.
A441457

Check whether the piston pin hole snap ring (1) has been correctly positioned in the groove (2).


g.

Check whether the opening in the marked area of the piston pin hole snap ring is pointing towards the piston top side (3).


Hide 3.INSPECT CYLINDER BORE

HINT:

The description is for one component only. The procedure is identical for all further components.


a.

Cylinder barrel is cleaned.


b.
A441173

Adjusting measuring bolt to nominal dimension of cylinder bore.

Cylinder bore:
Distance from the upper edge of the cylinder barrel to the measuring point Diameter of cylinder bore Permitted irregularity of the cylinder bore
0 to 60 mm (0 to 2.36 in.) 82.000 to 82.014 mm (3.228 to 3.229 in.) 0.007 mm (0.000276 in.)
60 to 80 mm (2.36 to 3.15 in.) 82.008 to 82.022 mm (3.2287 to 3.2292 in.) 0.007 mm (0.000276 in.)
80 to 115 mm (3.15 to 4.53 in.) 82.021 to 82.037 mm (3.2292 to 3.2298 in.) 0.007 mm (0.000276 in.)
115 to 135 mm (4.53 to 5.31 in.) 82.033 to 82.057 mm (3.230 to 3.231 in.) 0.010 mm (0.000394 in.)



c.

Insert internal measuring device into the micrometer and set to zero.


d.

With the internal measuring device, measure the cylinder at the following points and check the deviations from the nominal dimension.

i.

Lower third of the cylinder bore in direction of travel,


ii.

Lower third of the cylinder bore transversely to direction of travel,


iii.

Middle third of the cylinder bore in direction of travel,


iv.

Middle third of the cylinder bore transversely to direction of travel,


v.

Upper third of the cylinder bore in direction of travel,


vi.

Upper third of the cylinder bore transversely to direction of travel.

Cylinder bore:
Distance from the upper edge of the cylinder barrel to the measuring point Diameter of cylinder bore Permitted irregularity of the cylinder bore
0 to 60 mm (0 to 2.36 in.) 82.000 to 82.014 mm (3.228 to 3.229 in.) 0.007 mm (0.000276 in.)
60 to 80 mm (2.36 to 3.15 in.) 82.008 to 82.022 mm (3.2287 to 3.2292 in.) 0.007 mm (0.000276 in.)
80 to 115 mm (3.15 to 4.53 in.) 82.021 to 82.037 mm (3.2292 to 3.2298 in.) 0.007 mm (0.000276 in.)
115 to 135 mm (4.53 to 5.31 in.) 82.033 to 82.057 mm (3.230 to 3.231 in.) 0.010 mm (0.000394 in.)


HINT:

If the cylinder bore is not as specified, replace the crankcase.




Hide 13201 4.INSTALL CONNECTING ROD SUB-ASSEMBLY

NOTICE:
·

Damage on the cylinder wall and oil spray nozzles.

Major force can scratch the cylinder wall and bend the oil spray nozzles.

-

Carefully move the piston and connecting rod in the engine block.




HINT:

The description is for one component only. The procedure is identical for all further components.


a.
A441367

Align the contact points of all piston rings by 120° each.


b.

Do not position contact points over axis of piston pin (A).

Position number Description
1 12 o'clock position
2 4 o'clock position
3 8 o'clock position
A Axis of piston pin
K1 1. Piston ring (plain rectangular compression ring)
K2 2. Piston ring (taper faced piston ring)
O1 Oil scraper ring below
O2 Spiral expander
O3 Oil scraper ring above

Piston ring Align at the following position
Upper oil scraper ring (O3) Align at the 12 o'clock position (1)
Spiral expander (O2) Align at the 4 o'clock position (2)
Lower oil scraper ring (O1) Align at the 8 o'clock position (3)
Taper faced piston ring (K2) Align at the 12 o'clock position (1)
Plain rectangular compression ring (K1) Align at the 4 o'clock position (2)


c.
A441366

Make sure that contact point (1) does not overlap spring (O2).


d.
A447286

Coat the pistons (1) and piston rings lightly with oil.


e.

Insert the piston (1) with the piston rings into the piston ring compressor.


f.

Bolt special tool 2 463 755 on at large connecting rod eye (2).

SST
09200-WA730  


g.
A447287

Align the piston so that the arrow (1) points to cylinder 1.


h.

Insert piston with the connecting rod into the piston ring compressor and guide it into the cylinder.

NOTICE:
·

Damage on the cylinder wall and oil spray nozzles.

Major force can scratch the cylinder wall and bend the oil spray nozzles.

-

Carefully move the piston and connecting rod in the engine block.





Hide 5.INSTALL CONNECTING ROD CAP

a.
A441188

Vacuum the connecting rod bearing and cracked surface (1) with a vacuum cleaner (2).


b.
A441691

Insert the connecting rod bearing (1) into the connecting rod bearing cap (2).


c.

Apply a light coat of oil to the connecting rod bearing (1).


d.
A442079

If necessary, bolt the special tool (assembly tool) 2 463 755 into the large connecting rod eye.

SST
09200-WA730  


e.

Pull the connecting rod up to the connecting rod bearing journal.


f.
A441692

Attach the connecting rod bearing caps to the connecting rod until the designations (1) match.

NOTICE:
·

Engine damage caused by incorrectly installed connecting rod bearings and connecting rod bearing caps.

Engine damage may result from incorrectly installing connecting rod bearings and connecting rod bearing caps.

-

Always install all connecting rod bearings and connecting rod bearing caps in the same position from which they were removed.





g.
A441685

Replace bolts (1).


h.

Step 1:

i.

Tighten the E12 bolts (1).

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)



i.

Step 2:

i.

Tighten the bolts (1) 70° with the special tool 0 490 504 (00 9 120).

SST
09900-WA010  

HINT:
C417459C05
2.99,1.271 3.156,1.188 false 2.906,2.094 2.906,1.76 false 0.875,3 1.208,3 false 0.104,0.125 0.417,0.281 0.313,0.156 10 false *a 0.448,0.125 0.76,0.281 0.313,0.156 10 false *b 2.042,0.125 2.354,0.281 0.313,0.156 10 false *c 3.188,1.073 3.427,1.271 0.24,0.198 10 false *d 2.854,2.146 3.167,2.302 0.313,0.156 10 false *b 1.302,2.927 1.615,3.083 0.313,0.156 10 false *c
*a Example
*b Before Tightening
*c After Tightening
*d Magnetic Portion


·

The magnetic portion is used to secure the gauge to the vehicle.

·

After first adjusting the needle of the gauge to 0°, tighten to the specified angle.

·

Perform the work procedure carefully so that the gauge, etc. does not become tilted.





j.

Step 3:

i.

Tighten the bolts (1) another 70° with the special tool 0 490 504 (00 9 120).

SST
09900-WA010  

HINT:
C417459C05
2.99,1.271 3.156,1.188 false 2.906,2.094 2.906,1.76 false 0.875,3 1.208,3 false 0.104,0.125 0.417,0.281 0.313,0.156 10 false *a 0.448,0.125 0.76,0.281 0.313,0.156 10 false *b 2.042,0.125 2.354,0.281 0.313,0.156 10 false *c 3.188,1.073 3.427,1.271 0.24,0.198 10 false *d 2.854,2.146 3.167,2.302 0.313,0.156 10 false *b 1.302,2.927 1.615,3.083 0.313,0.156 10 false *c
*a Example
*b Before Tightening
*c After Tightening
*d Magnetic Portion


·

The magnetic portion is used to secure the gauge to the vehicle.

·

After first adjusting the needle of the gauge to 0°, tighten to the specified angle.

·

Perform the work procedure carefully so that the gauge, etc. does not become tilted.





Hide 12121 6.INSTALL NO. 1 OIL PAN BAFFLE PLATE

Hide 15100 7.INSTALL OIL PUMP ASSEMBLY

Hide 12101 8.INSTALL OIL PAN SUB-ASSEMBLY

Hide 12.SET NO. 1 CYLINDER TO TDC (COMPRESSION)

Hide 11101 13.INSTALL CYLINDER HEAD SUB-ASSEMBLY

Hide 14.INSPECT AND ADJUST CAMSHAFT WITH SPECIAL TOOL

Hide 13070A 15.INSTALL CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

Hide 135A0A 16.TEMPORARILY TIGHTEN EXHAUST CAMSHAFT TIMING GEAR BOLT ASSEMBLY

Hide 13050 17.INSTALL CAMSHAFT TIMING GEAR ASSEMBLY

Hide 135A0 18.TEMPORARILY TIGHTEN INTAKE CAMSHAFT TIMING GEAR BOLT ASSEMBLY

Hide 13506 19. PRETENSION TIMING CHAIN WITH SPECIAL TOOL

Hide 135A0A 20.TIGHTEN EXHAUST CAMSHAFT TIMING GEAR BOLT ASSEMBLY

Hide 135A0 21.TIGHTEN INTAKE CAMSHAFT TIMING GEAR BOLT ASSEMBLY

Hide 13540 23.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

Hide 25.INSTALL SPARK PLUG

Hide 17293 26.INSTALL TURBOCHARGER STAY

Hide 11201 29.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 15370J 30.INSTALL CAM TIMING OIL CONTROL SOLENOID ASSEMBLY

Hide 23250B 31.REPLACE FUEL INJECTOR SEAL

Hide 23250 32.INSTALL FUEL INJECTOR ASSEMBLY (for Rear Side)

Hide 23250 33.INSTALL FUEL INJECTOR ASSEMBLY (for Front Side)

Hide 23470 34.ADJUST FUEL PUMP LIFTER ASSEMBLY

Hide 23100X 35.INSTALL FUEL (ENGINE ROOM SIDE) PUMP ASSEMBLY

Hide 23801P 36.INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY