Home › Engine / Hybrid System › B58 (ENGINE MECHANICAL) › CRANKSHAFT › 2019.03–2020.03
RM3650E _51 Engine / Hybrid System _080179 B58 ENGINE MECHANICAL _0388893 CRANKSHAFT A

B58 ENGINE MECHANICAL  CRANKSHAFT  REASSEMBLY  


PROCEDURE

Hide 11711 1. CRANKSHAFT BEARING

a.
A441174

Replace crankshaft bearing with lubricating groove (1) and the crankshaft bearing (2).


b.
A441364

Replace upper crankshaft thrust washer (1) and the lower crankshaft thrust washer (2).


c.
A441352

Make sure the crankshaft bearing (1) is correctly installed with the claw in the highlighted area.


d.
A441353

Make sure the crankshaft bearing (1) is correctly installed with the claw in the highlighted area.


e.
A441349

Install crankshaft bearings (1) to (3) and (5) to (7) in to the crankshaft bearing cap.


f.

Install the lower crankshaft thrust washer (4) in the crankshaft bearing cap.


g.

Oil all crankshaft bearings and guide bearings (1) to (7).


h.
A441348

Install crankshaft bearings with lubricating groove (1) to (3) and (5) to (7) in the crankcase.


i.

Install the upper crankshaft thrust washer with lubricating groove (4) in the crankcase.


j.

Oil all crankshaft bearings and guide bearing shells with lubricating groove (1) to (7).


Hide 13411 2.INSTALL CRANKSHAFT

NOTICE:
·

Engine damage may result from incorrectly installing crankshaft bearings and crankshaft bearing caps.

-

Always install all crankshaft bearings and crankshaft bearing caps in the same position from which they were removed.




a.
A441351

Install the crankshaft (1).

CAUTION:
·

Heavy component.

Heavy components can lead to injury or damage.

-

Remove and install heavy components with the aid of another person/other persons.





b.
A441350

Observe the assignment and numbering (1) to (7) of the crankshaft bearing caps.

i.

(1) = Engine, front (vibration damper)


ii.

(7) = Clutch side

HINT:

The crankshaft bearing cap, main bearing shell and guide bearing shell are aligned with each other.

Always install the crankshaft bearing cap, main bearing shells and guide bearing shells in the cylinder from which they were removed.




c.

Position the crankshaft bearing caps (1) to (7).


d.
A441354

Replace bolts (1) to (14).


e.

Step 1:

i.

Tighten the E14 bolts in sequence (1) to (14).

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)



f.

Step 2:

i.

Tighten the bolts 65° in the order shown in step 1 with the special tool 0 490 504 (00 9 120).

SST
09900-WA010  

HINT:
C417459C05
2.99,1.271 3.156,1.188 false 2.906,2.094 2.906,1.76 false 0.875,3 1.208,3 false 0.104,0.125 0.417,0.281 0.313,0.156 10 false *a 0.448,0.125 0.76,0.281 0.313,0.156 10 false *b 2.042,0.125 2.354,0.281 0.313,0.156 10 false *c 3.188,1.073 3.427,1.271 0.24,0.198 10 false *d 2.854,2.146 3.167,2.302 0.313,0.156 10 false *b 1.302,2.927 1.615,3.083 0.313,0.156 10 false *c
*a Example
*b Before Tightening
*c After Tightening
*d Magnetic Portion


·

The magnetic portion is used to secure the gauge to the vehicle.

·

After first adjusting the needle of the gauge to 0°, tighten to the specified angle.

·

Perform the work procedure carefully so that the gauge, etc. does not become tilted.





g.

Step 3:

i.

Tighten the bolts another 65° in the order shown in step 1 with the special tool 0 490 504 (00 9 120).

SST
09900-WA010  

HINT:
C417459C05
2.99,1.271 3.156,1.188 false 2.906,2.094 2.906,1.76 false 0.875,3 1.208,3 false 0.104,0.125 0.417,0.281 0.313,0.156 10 false *a 0.448,0.125 0.76,0.281 0.313,0.156 10 false *b 2.042,0.125 2.354,0.281 0.313,0.156 10 false *c 3.188,1.073 3.427,1.271 0.24,0.198 10 false *d 2.854,2.146 3.167,2.302 0.313,0.156 10 false *b 1.302,2.927 1.615,3.083 0.313,0.156 10 false *c
*a Example
*b Before Tightening
*c After Tightening
*d Magnetic Portion


·

The magnetic portion is used to secure the gauge to the vehicle.

·

After first adjusting the needle of the gauge to 0°, tighten to the specified angle.

·

Perform the work procedure carefully so that the gauge, etc. does not become tilted.





h.

Step 4:

i.

Release E14 bolts (1) to (14).



i.

Step 5:

i.

Tighten the E14 bolts in sequence (1) to (14).

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)



j.

Step 6:

i.

Tighten the bolts 65° in the order shown in step 1 with the special tool 0 490 504 (00 9 120).

SST
09900-WA010  

HINT:
C417459C05
2.99,1.271 3.156,1.188 false 2.906,2.094 2.906,1.76 false 0.875,3 1.208,3 false 0.104,0.125 0.417,0.281 0.313,0.156 10 false *a 0.448,0.125 0.76,0.281 0.313,0.156 10 false *b 2.042,0.125 2.354,0.281 0.313,0.156 10 false *c 3.188,1.073 3.427,1.271 0.24,0.198 10 false *d 2.854,2.146 3.167,2.302 0.313,0.156 10 false *b 1.302,2.927 1.615,3.083 0.313,0.156 10 false *c
*a Example
*b Before Tightening
*c After Tightening
*d Magnetic Portion


·

The magnetic portion is used to secure the gauge to the vehicle.

·

After first adjusting the needle of the gauge to 0°, tighten to the specified angle.

·

Perform the work procedure carefully so that the gauge, etc. does not become tilted.





k.

Step 7:

i.

Tighten the bolts another 65° in the order shown in step 1 with the special tool 0 490 504 (00 9 120).

SST
09900-WA010  

HINT:
C417459C05
2.99,1.271 3.156,1.188 false 2.906,2.094 2.906,1.76 false 0.875,3 1.208,3 false 0.104,0.125 0.417,0.281 0.313,0.156 10 false *a 0.448,0.125 0.76,0.281 0.313,0.156 10 false *b 2.042,0.125 2.354,0.281 0.313,0.156 10 false *c 3.188,1.073 3.427,1.271 0.24,0.198 10 false *d 2.854,2.146 3.167,2.302 0.313,0.156 10 false *b 1.302,2.927 1.615,3.083 0.313,0.156 10 false *c
*a Example
*b Before Tightening
*c After Tightening
*d Magnetic Portion


·

The magnetic portion is used to secure the gauge to the vehicle.

·

After first adjusting the needle of the gauge to 0°, tighten to the specified angle.

·

Perform the work procedure carefully so that the gauge, etc. does not become tilted.





Hide 3.INSPECT CRANKSHAFT THRUST CLEARANCE

a.
A455566

Using a dial indicator, check crankshaft thrust clearance.

Axial play of crankshaft:

0.09 to 0.314 mm (0.00354 to 0.01236 in.)


HINT:

If the thrust clearance is not as specified, replace worn components.



Hide 4.INSPECT CRANKSHAFT

a.
A441707

Turn the crankshaft clockwise with the special tool 0 490 130 (00 2 010) and compare the reading on the scale to the maximum permitted torque.

SST
09200-WA190  

Maximum permitted torque of the crankshaft:

12 N*m (122 kgf*cm, 9 ft.*lbf)


HINT:

If the maximum permitted torque is exceeded, correct the radial clearance.



Hide 13201 7.INSTALL CONNECTING ROD SUB-ASSEMBLY

Hide 12121 8.INSTALL NO. 1 OIL PAN BAFFLE PLATE

a.
A442078

Replace bolts (markings).


b.

Insert No. 1 oil pan baffle plate (1) and position.


c.

Tighten the E10 bolts in a crosswise pattern.

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)


d.

Using SST, tighten the E10 bolts an additional 45°.

SST
09900-WA010  

HINT:
C417459C05
2.99,1.271 3.156,1.188 false 2.906,2.094 2.906,1.76 false 0.875,3 1.208,3 false 0.104,0.125 0.417,0.281 0.313,0.156 10 false *a 0.448,0.125 0.76,0.281 0.313,0.156 10 false *b 2.042,0.125 2.354,0.281 0.313,0.156 10 false *c 3.188,1.073 3.427,1.271 0.24,0.198 10 false *d 2.854,2.146 3.167,2.302 0.313,0.156 10 false *b 1.302,2.927 1.615,3.083 0.313,0.156 10 false *c
*a Example
*b Before Tightening
*c After Tightening
*d Magnetic Portion


·

The magnetic portion is used to secure the gauge to the vehicle.

·

After first adjusting the needle of the gauge to 0°, tighten to the specified angle.

·

Perform the work procedure carefully so that the gauge, etc. does not become tilted.




Hide 13507A 9.INSTALL OIL PUMP DRIVE CHAIN SUB-ASSEMBLY

a.
A442091

Guide in and install oil pump drive chain sub-assembly (1) on crankshaft (2).


Hide 15100 10.INSTALL OIL PUMP ASSEMBLY

Hide 13506 11.INSTALL CHAIN SUB-ASSEMBLY

Hide 12101 14.INSTALL OIL PAN SUB-ASSEMBLY

NOTICE:
·

Contaminant or foreign body.

Contamination can result in malfunctions, operating failure or leaks.

-

Adhere to the utmost cleanliness.

-

Protect components from contamination e.g. by covering.

-

Close off line connections with seal plugs.



·

Damage to the surface.

The use of metal-cutting tools (e.g. sandpaper) to clean the surfaces can damage them and lead to leaks or engine damage.

-

Do not use any metal-cutting tools.




a.
A444611

Remove coarse seal packing remains on the sealing surface of the cylinder block (1) and the sealing surface on the oil pan sub-assembly.

SST
09900-WA030  

NOTICE:

The sealing surfaces must be free from oils, grease and cleaning agents.



b.
A444612

Remove fine seal packing remains on the sealing surface of the oil pan sub-assembly (1) and the sealing surface on the cylinder block.

NOTICE:

The sealing surfaces must be free from oils, grease and cleaning agents.



c.

Load the sealer gun with the seal packing.

Seal Packing:

Loctite 5970 Flange Sealant



d.
A441243

Apply sealing bead (1) with the seal packing in the marked area along the inner edge.

Height of the sealing bead:

2.0 to 2.5 mm (0.0787 to 0.0984 in.)


NOTICE:
·

The application time of the liquid sealing compound can be at a maximum of 10 min.

·

Start-up of the assembly is not possible until 25 minutes after the application time.

·

Non-observance can lead to leaks in the assembly.




e.

Completely encircle the oil return orifice (arrow) with the seal packing.


f.
A445109

Using a straightedge, position the oil pan sub-assembly and timing case cover so that their surfaces are aligned.

HINT:

The straightedge is only required when the transmission is removed.



g.
A441242

Insert oil pan sub-assembly (1) upwards and forwards and position.


h.
A441936

Tighten all the oil pan sub-assembly E10 bolts (marks) hand-tight, do not yet tighten fully.


i.
A446321

Tighten the E10 bolts (1).

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)


j.
A441936

Tighten all E10 bolts (marks).

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)


k.
A441934

Connect connectors (1) and lock.

HINT:

Make sure the connector engages audibly.



l.

Secure clamps (2).


Hide 15.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

Hide 16.REMOVE AND INSTALL FRONT CRANKSHAFT OIL SEAL

a.
A441373

Drive in the front crankshaft oil seal (1) in themarked area with a punch to approx. 1 cm deep.

HINT:
·

Scratches.

Tools and sharp-edged components cancause scratches.

-

Protect working area.

-

Handle tools and componentscarefully.





b.
A445283

Carefully lever out and remove the front crankshaftoil seal (1).


c.
A441293

Clean sealing surface (1).


d.
A441289

Clean the special tool 0 496 128 (11 8 801) fromthe set of special tools 0 496 127 (11 8 800) andcoat it with fresh engine oil.

SST
09200-WA080  


e.
A441290

Position the special tool 0 496 128 (11 8 801) from the set of special tools 0 496 127 (11 8 800) onthe crankshaft and bolt it on.

SST
09200-WA080  

HINT:
·

Front crankshaft oil seal damage.Touching the sealing lip (inner) andapplying oil to the front crankshaft oilseal will lead to its destruction.

-

Do not touch the sealing lip (inner)of the front crankshaft oil seal.

-

Do not apply oil to the frontcrankshaft oil seal.

-

Install the front crankshaft oil sealdry.





f.

Replace front crankshaft oil seal (1).


g.

Carefully slide the front crankshaft oil seal (1) straight in a rotational movement onto the specialtool 0 496 128 (11 8 801) from the set of special tools 0 496 127 (11 8 800) until the frontcrankshaft oil seal is positioned flush against the cylinder block sub-assembly.

SST
09200-WA080  


h.
A441291

Position the special tool 0 496 130 (11 8 803) fromthe set of special tools 0 496 127 (11 8 800) andbolt on hand-tight with the nut.

SST
09200-WA080  


i.

Ensure that the front crankshaft oil seal moves inevenly.


j.
A441292

Bolt in the special tool (sleeve) 0 496 130 (11 8803) from the set of special tools 0 496 127 (11 8800) with the tool (1) until the special tool(sleeve)0 496 130 (11 8 803) is flush with thecylinder block sub-assembly.

SST
09200-WA080  


Hide 21.SET NO. 1 CYLINDER TO TDC (COMPRESSION)

NOTICE:
·

Damage to the engine.

The engine may be damaged if it is manually rotated in the wrong direction.

-

Always rotate the engine in the correct direction of rotation by hand: a) Clockwise, facing the vibration damper or b) Counter-clockwise, facing the timing chain. (b) only applies when the chain sub-assembly is installed.




a.
A441295

Turn the engine with the special tool 0 493 380 (11 6 480) to the TDC firing position of cylinder 1.

SST
09200-WA190  


b.
A441989

Guide out and remove sealing cap (1) on oil pan sub-assembly (2).


c.
A441713

Make sure that the special tool 2 288 380 is positioned correctly .

SST
09200-WA570  

i.

The engine is in the TDC firing position of cylinder 1.



d.
A441714

The TDC firing position of the 1st cylinder is not reached and the special tool 2 288 380 is positioned incorrectly: Position the special tool 2 288 380 again.

SST
09200-WA570  


Hide 11101 22.INSTALL CYLINDER HEAD SUB-ASSEMBLY

Hide 13070A 24.INSTALL CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

Hide 135A0A 25.TEMPORARILY TIGHTEN EXHAUST CAMSHAFT TIMING GEAR BOLT ASSEMBLY

Hide 13050 26.INSTALL CAMSHAFT TIMING GEAR ASSEMBLY

Hide 135A0 27.TEMPORARILY TIGHTEN INTAKE CAMSHAFT TIMING GEAR BOLT ASSEMBLY

Hide 13506 28.TEMPORARILY INSTALL CHAIN SUB-ASSEMBLY

a.
A442019

Pretension the timing chain correctly with the special tool 2 455 654 .

SST
09200-WA810  


b.

Make sure that pin (1) is flush with housing (2).


c.
A442020

Make sure that the preload of the timing chain is not insufficient. The preload is insufficient when the pin (1) of the special tool 2 455 654 is not aligned flush with the housing (2). The timing chain is not correctly pre-tensioned.

SST
09200-WA810  


d.
A442021

Make sure that the preload of the timing chain is not too high. The preload is too high when the pin (1) of the special tool 2 455 654 is not aligned flush with the housing (2). The timing chain is not correctly pre-tensioned.

SST
09200-WA810  


Hide 135A0A 29.TIGHTEN EXHAUST CAMSHAFT TIMING GEAR BOLT ASSEMBLY

Hide 135A0 30.TIGHTEN INTAKE CAMSHAFT TIMING GEAR BOLT ASSEMBLY

Hide 31.REMOVE SST

a.
A442031

Release the bolts (arrows) from the set of special tools 2 456 372 .

SST
09200-WA700  


b.

Guide the setting gauge 0.5 ° (3) out of the special tool 2 456 372 between the exhaust camshaft and basic carrier (1) and remove it.

SST
09200-WA700  


c.

Guide setting gauge 0.7 ° (2) out of the special tool 2 456 372 between the intake camshaft and basic carrier (1) and remove it.

SST
09200-WA700  


d.
A442011

Unscrew the bolts (2) from the set of special tools 2 456 372 .

SST
09200-WA700  


e.

Thread the basic carrier (1) out of the special tool 2 456 372 and remove.

SST
09200-WA700  


f.
A441987

Guide the special tool 2 288 380 out and remove.

SST
09200-WA570  


g.
A441295

Guide the special tool 0 493 380 (11 6 480) out and remove.

SST
09200-WA190  


h.
A442030

Guide the special tool 2 455 654 (1) out and remove.

SST
09200-WA810  


Hide 13540 32.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

Hide 33.INSPECT CAMSHAFT TIMING

a.
A441295

Turn the engine with the special tool 0 493 380 (11 6 480) to the TDC firing position of cylinder 1.

SST
09200-WA190  

NOTICE:
·

Damage to the engine.

The engine may be damaged if it is manually rotated in the wrong direction.

-

Always rotate the engine in the correct direction of rotation by hand: a) Clockwise, facing the crankshaft pulley assembly or b) Counter-clockwise, facing the timing chain. (b) only applies when the chain sub-assembly is installed.





b.
A441986

Make sure that the marks (1) on the intake camshaft sub-assembly (E) and the exhaust camshaft sub-assembly (A) are legible from above.


c.
A441416

Ensure that the cam (1) on the exhaust camshaft sub-assembly on cylinder 1 points to the inside right at a slight angle.


d.
A441985

Ensure that the cam (1) on the intake camshaft sub-assembly on cylinder 1 points to the inside left at an angle.


e.
A441418

Ensure that the flattened areas (1) on the intake camshaft sub-assembly and the exhaust camshaft sub-assembly point upwards.


f.
A442011

Position the basic carrier (1) from the set of special tools 2 456 372 on the cylinder head sub-assembly.

SST
09200-WA700  


g.

Tighten the bolts (2) from the set of special tools 2 456 372 .

SST
09200-WA700  

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


h.
A442012

Position the test gauge (2) from the set of special tools 2 358 122 between the intake camshaft sub-assembly and the basic carrier (1) from the set of special tools 2 456 372 .

SST
09200-WA380  
09200-WA700  


i.

Position the test gauge (3) from the set of special tools 2 358 122 between the exhaust camshaft sub-assembly and the basic carrier (1) from the set of special tools 2 456 372 .

SST
09200-WA380  
09200-WA700  


j.

Tighten bolts (arrows).

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


k.
A441989

Guide out and remove sealing cap (1) on oil pan sub-assembly (2).


l.
A441713

Position the special tool 2 288 380 correctly in the dowel hole .

SST
09200-WA570  

i.

The engine is in the TDC firing position of cylinder 1.



m.
A441714

Make sure that the special tool 2 288 380 is not positioned incorrectly.

SST
09200-WA570  

i.

The TDC firing position of cylinder 1 was not reached.



Hide 34.INSTALL SPARK PLUG

Hide 17293 35.INSTALL TURBOCHARGER STAY

a.
A441294

Replace bolts (2).


b.

Position support and tighten with the T45 bolt (2).

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


c.

Replace bolts (1).


d.

Tighten down T45 bolt (1).

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


Hide 11201 38.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 15370J 39.INSTALL CAM TIMING OIL CONTROL SOLENOID ASSEMBLY

Hide 23250B 40.REPLACE FUEL INJECTOR SEAL

Hide 23250 41.INSTALL FUEL INJECTOR ASSEMBLY (for Rear Side)

Hide 23250 42.INSTALL FUEL INJECTOR ASSEMBLY (for Front Side)

Hide 23470 43.ADJUST FUEL PUMP LIFTER ASSEMBLY

Hide 23100X 44.INSTALL FUEL (ENGINE ROOM SIDE) PUMP ASSEMBLY

Hide 23801P 45.INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY