1.INSTALL PISTON RING
Very wide spreading of the piston rings during installation / removal.
Damage to the piston rings.
Spread the piston rings only until the piston ring can just be slid over the piston.
Use piston ring pliers to install and remove the piston rings.
Clean the used pistons carefully. Do not use a metal-cutting tool to avoid damaging the pistons.
Wear safety goggles.
The description is for one component only. The procedure is identical for all further components.
Determining the correct set of the piston ring (1):
| Engine | Set of the piston rings |
|---|---|
| B58 (2 Port Type) | 13011-WAA02 |
| B58 (6 Port Type) | 13011-WAA01
13011-WAA03 |
Keep the standard piston ring pliers (1) ready.
Correctly prepare the piston rings:
Upper piston ring (1): Plain rectangular compression ring (engraving must point upwards)
Centre piston ring (2): Taper faced piston ring (engraving must point upwards)
Oil scraper ring (3): consists of 2 piston rings ((O1), (O3)) with a spring (O2) in the centre.
Make sure that the assembly mark TOP (1) points to the top to the combustion chamber.
If there is no assembly mark TOP (1), then the piston ring with the writing must point to the top to the combustion chamber.
Attach the oil scraper rings (1) and springs (2) manually (see following steps).
Slide the spring (1) on to the piston (2) and install it.
Slide the two oil scraper rings (1) on to the piston (2) and install them.
Position the centre piston ring (1) in the marked area at the piston ring pliers (2).
Clamp the piston ring pliers (1) in the direction of arrow and feed in the centre piston ring (2) in the piston (3) and install it.
Release the piston ring pliers (1) at the centre piston ring (2).
Feed out the piston ring pliers (1) at the centre piston ring (2) and remove it.
Position the upper piston ring (1) in the marked area at the piston ring pliers (2).
Clamp the piston ring pliers (1) in the direction of arrow and feed in the upper piston ring (2) in the piston (3) and install it.
Release the piston ring pliers (1) at the upper piston ring (2).
Feed out the piston ring pliers (1) at the upper piston ring (2) and remove it.
2.INSTALL PISTON
Install piston pin (1) in piston (2) and connecting rod (3).
Piston and piston pin are matched to each other.
Always install piston and piston pin together and do not switch by mistake.
Position the piston pin hole snap ring (1) such that the opening in the marked area of the piston pin hole snap ring points in the direction of the piston top side (2).
Piston pin hole snap ring with preload.
Danger of injury!
The use of the specified special tool for the disassembly or installation is mandatory.
Wear safety goggles.
piston pin with 12.0 mm internal diameter :
Preload the piston pin hole snap ring (1) using your thumb.
Simultaneously press the piston pin hole snap ring into the piston using special tools 2 410 685 and 2 463 754.
Twist and reposition special tool 2 410 685 and completely press the piston pin hole snap ring into the piston.
piston pin with 12.5 mm internal diameter :
Preload the piston pin hole snap ring (1) using your thumb.
Simultaneously press the piston pin hole snap ring into the piston using special tools 2 410 685 and 2 463 754.
Twist and reposition special tool 2 410 685 and completely press the piston pin hole snap ring into the piston.
Check whether the piston pin hole snap ring (1) has been correctly positioned in the groove (2).
Check whether the opening in the marked area of the piston pin hole snap ring is pointing towards the piston top side (3).
3.INSPECT CYLINDER BORE
The description is for one component only. The procedure is identical for all further components.
Cylinder barrel is cleaned.
Adjusting measuring bolt to nominal dimension of cylinder bore.
| Distance from the upper edge of the cylinder barrel to the measuring point | Diameter of cylinder bore | Permitted irregularity of the cylinder bore |
| 0 to 60 mm (0 to 2.36 in.) | 82.000 to 82.014 mm (3.228 to 3.229 in.) | 0.007 mm (0.000276 in.) |
| 60 to 80 mm (2.36 to 3.15 in.) | 82.008 to 82.022 mm (3.2287 to 3.2292 in.) | 0.007 mm (0.000276 in.) |
| 80 to 115 mm (3.15 to 4.53 in.) | 82.021 to 82.037 mm (3.2292 to 3.2298 in.) | 0.007 mm (0.000276 in.) |
| 115 to 135 mm (4.53 to 5.31 in.) | 82.033 to 82.057 mm (3.230 to 3.231 in.) | 0.010 mm (0.000394 in.) |
Insert internal measuring device into the micrometer and set to zero.
With the internal measuring device, measure the cylinder at the following points and check the deviations from the nominal dimension.
Lower third of the cylinder bore in direction of travel,
Lower third of the cylinder bore transversely to direction of travel,
Middle third of the cylinder bore in direction of travel,
Middle third of the cylinder bore transversely to direction of travel,
Upper third of the cylinder bore in direction of travel,
Upper third of the cylinder bore transversely to direction of travel.
| Distance from the upper edge of the cylinder barrel to the measuring point | Diameter of cylinder bore | Permitted irregularity of the cylinder bore |
| 0 to 60 mm (0 to 2.36 in.) | 82.000 to 82.014 mm (3.228 to 3.229 in.) | 0.007 mm (0.000276 in.) |
| 60 to 80 mm (2.36 to 3.15 in.) | 82.008 to 82.022 mm (3.2287 to 3.2292 in.) | 0.007 mm (0.000276 in.) |
| 80 to 115 mm (3.15 to 4.53 in.) | 82.021 to 82.037 mm (3.2292 to 3.2298 in.) | 0.007 mm (0.000276 in.) |
| 115 to 135 mm (4.53 to 5.31 in.) | 82.033 to 82.057 mm (3.230 to 3.231 in.) | 0.010 mm (0.000394 in.) |
If the cylinder bore is not as specified, replace the crankcase.
13201
4.INSTALL CONNECTING ROD SUB-ASSEMBLY
Damage on the cylinder wall and oil spray nozzles.
Major force can scratch the cylinder wall and bend the oil spray nozzles.
Carefully move the piston and connecting rod in the engine block.
The description is for one component only. The procedure is identical for all further components.
Align the contact points of all piston rings by 120° each.
Do not position contact points over axis of piston pin (A).
| Position number | Description |
|---|---|
| 1 | 12 o'clock position |
| 2 | 4 o'clock position |
| 3 | 8 o'clock position |
| A | Axis of piston pin |
| K1 | 1. Piston ring (plain rectangular compression ring) |
| K2 | 2. Piston ring (taper faced piston ring) |
| O1 | Oil scraper ring below |
| O2 | Spiral expander |
| O3 | Oil scraper ring above |
| Piston ring | Align at the following position |
|---|---|
| Upper oil scraper ring (O3) | Align at the 12 o'clock position (1) |
| Spiral expander (O2) | Align at the 4 o'clock position (2) |
| Lower oil scraper ring (O1) | Align at the 8 o'clock position (3) |
| Taper faced piston ring (K2) | Align at the 12 o'clock position (1) |
| Plain rectangular compression ring (K1) | Align at the 4 o'clock position (2) |
Make sure that contact point (1) does not overlap spring (O2).
Coat the pistons (1) and piston rings lightly with oil.
Insert the piston (1) with the piston rings into the piston ring compressor.
Bolt special tool 2 463 755 on at large connecting rod eye (2).
Align the piston so that the arrow (1) points to cylinder 1.
Insert piston with the connecting rod into the piston ring compressor and guide it into the cylinder.
Damage on the cylinder wall and oil spray nozzles.
Major force can scratch the cylinder wall and bend the oil spray nozzles.
Carefully move the piston and connecting rod in the engine block.
5.INSTALL CONNECTING ROD CAP
Vacuum the connecting rod bearing and cracked surface (1) with a vacuum cleaner (2).
Insert the connecting rod bearing (1) into the connecting rod bearing cap (2).
Apply a light coat of oil to the connecting rod bearing (1).
If necessary, bolt the special tool (assembly tool) 2 463 755 into the large connecting rod eye.
Pull the connecting rod up to the connecting rod bearing journal.
Attach the connecting rod bearing caps to the connecting rod until the designations (1) match.
Engine damage caused by incorrectly installed connecting rod bearings and connecting rod bearing caps.
Engine damage may result from incorrectly installing connecting rod bearings and connecting rod bearing caps.
Always install all connecting rod bearings and connecting rod bearing caps in the same position from which they were removed.
Replace bolts (1).
Step 1:
Tighten the E12 bolts (1).
Step 2:
Tighten the bolts (1) 70° with the special tool 0 490 504 (00 9 120).
| *a | Example |
| *b | Before Tightening |
| *c | After Tightening |
| *d | Magnetic Portion |
The magnetic portion is used to secure the gauge to the vehicle.
After first adjusting the needle of the gauge to 0°, tighten to the specified angle.
Perform the work procedure carefully so that the gauge, etc. does not become tilted.
Step 3:
Tighten the bolts (1) another 70° with the special tool 0 490 504 (00 9 120).
| *a | Example |
| *b | Before Tightening |
| *c | After Tightening |
| *d | Magnetic Portion |
The magnetic portion is used to secure the gauge to the vehicle.
After first adjusting the needle of the gauge to 0°, tighten to the specified angle.
Perform the work procedure carefully so that the gauge, etc. does not become tilted.
12121
6.INSTALL NO. 1 OIL PAN BAFFLE PLATE
15100
7.INSTALL OIL PUMP ASSEMBLY
12101
8.INSTALL OIL PAN SUB-ASSEMBLY
9. SEALING OIL DUCT
10.CLEAN SEALING SURFACES
11115
11.INSTALL CYLINDER HEAD GASKET
12.SET NO. 1 CYLINDER TO TDC (COMPRESSION)
11101
13.INSTALL CYLINDER HEAD SUB-ASSEMBLY
14.INSPECT AND ADJUST CAMSHAFT WITH SPECIAL TOOL
13070A
15.INSTALL CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
135A0A
16.TEMPORARILY TIGHTEN EXHAUST CAMSHAFT TIMING GEAR BOLT ASSEMBLY
13050
17.INSTALL CAMSHAFT TIMING GEAR ASSEMBLY
135A0
18.TEMPORARILY TIGHTEN INTAKE CAMSHAFT TIMING GEAR BOLT ASSEMBLY
13506
19. PRETENSION TIMING CHAIN WITH SPECIAL TOOL
135A0A
20.TIGHTEN EXHAUST CAMSHAFT TIMING GEAR BOLT ASSEMBLY
135A0
21.TIGHTEN INTAKE CAMSHAFT TIMING GEAR BOLT ASSEMBLY
22.REMOVE SST
13540
23.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY
24.INSPECT CAMSHAFT TIMING
25.INSTALL SPARK PLUG
17293
26.INSTALL TURBOCHARGER STAY
15474
27.INSTALL OUTLET TURBO OIL PIPE
17111
28.INSTALL INTAKE MANIFOLD
11201
29.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY
15370J
30.INSTALL CAM TIMING OIL CONTROL SOLENOID ASSEMBLY
23250B
31.REPLACE FUEL INJECTOR SEAL
23250
32.INSTALL FUEL INJECTOR ASSEMBLY (for Rear Side)
23250
33.INSTALL FUEL INJECTOR ASSEMBLY (for Front Side)
23470
34.ADJUST FUEL PUMP LIFTER ASSEMBLY
23100X
35.INSTALL FUEL (ENGINE ROOM SIDE) PUMP ASSEMBLY
23801P
36.INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY
37.ADD ENGINE OIL
17882
38.INSTALL NO. 2 AIR CLEANER HOSE
39.INSTALL ENGINE ASSEMBLY