Home › Engine / Hybrid System › 1NZ-FE ENGINE CONTROL › 1NZ-FE SFI SYSTEM › 2011.08–2014.07
RM19S0E _51 Engine / Hybrid System _051448 1NZ-FE ENGINE CONTROL _0248039 1NZ-FE SFI SYSTEM C

1NZ-FE ENGINE CONTROL  1NZ-FE SFI SYSTEM  P1603  Engine Stall History  P1605  Rough Idling  


DESCRIPTION

P1603

After starting the engine, this DTC is stored when the engine stops without the ignition switch being operated.

Using the intelligent tester, the conditions present when the DTC was stored can be confirmed by referring to the freeze frame data. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.

It is necessary to check if the vehicle has run out of fuel in the past before performing troubleshooting, as this DTC is also stored when the engine stalls due to running out of fuel.

DTC No. DTC Detection Condition Trouble Area
P1603*1 After monitoring for startability problems (P1604) finishes and 5 seconds or more elapse after starting the engine, with the engine running, the engine stops (the engine speed drops to 200 rpm or less) without the ignition switch being operated for 0.5 seconds or more (1 trip detection logic).
·

Air leak in intake system

·

Purge VSV

·

Brake booster hose not connected properly

·

Mass air flow meter

·

Engine coolant temperature sensor

·

Wire harness or connector

·

Heated oxygen sensor (sensor 1)

·

Power supply circuit (purge VSV, fuel injector assembly, No. 1 ignition coil)

·

Fuel pump

·

Fuel pump control circuit

·

Fuel line (fuel filter, pipes and hoses)

·

Throttle with motor body assembly

·

Camshaft timing oil control valve assembly

·

Knock sensor

·

Air conditioning system

·

Power steering system

·

Electrical load signal system

·

Automatic transaxle system

·

Park/neutral position switch assembly

·

ECM



*1: for Automatic Transaxle

P1605

This DTC is stored if the engine speed drops below the set speed.

Using the intelligent tester, the conditions present when the DTC was stored can be confirmed by referring to the freeze frame data. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.

It is necessary to check if the vehicle has run out of fuel in the past before performing troubleshooting, as this DTC is also stored when idling is unstable due to running out of fuel.

DTC No. DTC Detection Condition Trouble Area
P1605 After 5 seconds or more elapse after starting the engine, with the engine running, the engine speed drops to 400 rpm or less (1 trip detection logic).
·

Air leak in intake system

·

Purge VSV

·

Brake booster hose not connected properly

·

Mass air flow meter

·

Engine coolant temperature sensor

·

Wire harness or connector

·

Heated oxygen sensor (sensor 1)

·

Power supply circuit (purge VSV, fuel injector assembly, No. 1 ignition coil)

·

Fuel pump

·

Fuel pump control circuit

·

Fuel line (fuel filter, pipes and hoses)

·

Throttle with motor body assembly

·

Camshaft timing oil control valve assembly

·

Knock sensor

·

No. 1 ignition coil

·

Fuel injector assembly

·

Spark plug(s)

·

Air conditioning system

·

Power steering system

·

Electrical load signal system

·

Automatic transaxle system*1

·

Park/neutral position switch assembly*1

·

ECM



*1: for Automatic Transaxle

Reference waveforms showing a normal cold engine start


A259947


Reference waveforms showing a normal warm engine start


A258726


Reference values when there is an air leak in the air induction system during rough idling


Freeze Frame Data P1605 Rough Idling
Engine and ECT
Current P1605: Rough Idling
Time Freeze Frame Data
Item Data1 Data2 Data3 Data4 Data5 Unit
Engine Speed 685 467 429 382 532 rpm
Calculate Load 30.5 36.8 41.5 43.1 48.6 %
Vehicle Load 20.7 47.4 31.3 35.6 34.9 %
MAF 1.85 2.85 1.73 1.76 2.40 gm/sec
Atmosphere Pressure 103 103 103 103 103 kPa
Coolant Temp 86 86 86 86 86 °C
Intake Air 42 42 42 42 42 °C
Ambient Temperature 23 23 23 23 23 °C
Battery Voltage 13.222 12.929 12.851 12.792 13.046 V
Throttle Sensor Volt % 15.2 15.6 15.6 17.2 17.2 %
Throttle Sensor #2 Volt % 47.0 47.4 47.0 48.6 49.0 %
Throttle Sensor Position 0.0 0.0 0.0 0.0 0.0 %
Throttle Motor DUTY 15.2 15.6 16.8 20.3 16.8 %
Injector (Port) 2569 2770 3430 3589 4291 μs
Injection Volume (Cylinder 1) 0.070 0.069 0.069 0.069 0.069 ml
Fuel Pump/Speed Status ON ON ON ON ON
EVAP (Purge) VSV 0.0 0.0 0.0 0.0 0.0 %
Evap Purge Flow 0.0 0.0 0.0 0.0 0.0 %
Purge Density Learn Value 0.000 0.000 0.000 0.000 0.000
EVAP purge VSV OFF OFF OFF OFF OFF
Target Air-Fuel Ratio 1.011 1.011 1.009 1.009 1.009
O2S B1 S1 0.055 0.055 0.055 0.055 0.055 V
O2S B1 S2 0.000 0.000 0.000 0.000 0.000 V
Short FT #1 0.000 0.000 0.000 0.000 0.000 %
Long FT #1 -4.688 -5.469 -5.469 -5.469 -4.688 %
Total FT #1 0.000 0.000 0.000 0.000 0.000
Fuel System Status #1 OL OL OL OL OL
IGN Advance 7.0 11.0 9.5 9.0 7.0 deg
Knock Feedback Value -1.5 -1.5 -1.5 -1.5 -1.5 °CA
Knock Correct Learn Value 14.0 14.0 14.0 14.0 14.0 °CA
VVT Control Status #1 ON ON ON ON ON
Starter Signal OFF OFF OFF OFF OFF


WIRING DIAGRAM

Refer to DTC P0031 for the heated oxygen sensor circuit (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>P0031).

Refer to DTC P0443 for Purge VSV circuit (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>P0443).

Refer to DTC P0351 for the ignition coil circuit (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>P0351).

Refer to Fuel Injector Circuit (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>Fuel Injector Circuit).

CAUTION / NOTICE / HINT

HINT:
·

In contrast to normal malfunction diagnosis for components, circuits and systems, DTCs P1603 and P1605 are used to determine the malfunctioning area from the problem symptoms and freeze frame data when the user mentions problems such as engine stall.

As these DTCs can be stored as a result of certain user actions, even if these DTCs are output, if the customer makes no mention of problems, clear these DTCs without performing any troubleshooting and return the vehicle to the customer.

·

If any other DTCs are output, perform troubleshooting for those DTCs first.

·

Use any information from the customer problem analysis about the condition of the vehicle at the time when the problem occurred (how the engine stopped, conditions when the engine was restarted, etc.) as a reference.

Symptom Suspected Area
Engine vibration occurs and engine stops Air-fuel ratio abnormal
Engine stops with no engine vibration Ignition system, injection stoppage, high load from external parts
Engine can be started with accelerator pedal depressed Insufficient air volume
Rough idling after engine started Air-fuel ratio abnormal, abnormal combustion

·

Read freeze frame data using the intelligent tester. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.

·

When confirming the freeze frame data, be sure to check all 5 sets of freeze frame data (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>FREEZE FRAME DATA).

·

When DTC P1603 (Engine Stall History) is stored, DTC P1605 (Rough Idling) is also stored. When confirming freeze frame data, check DTC P1605. (The ECM stores DTC P1605 first. Therefore, the 5 sets of freeze frame data can be confirmed through DTC P1605, enabling the technician to obtain more information.)

·

When confirming freeze frame data, if there are multiple items related to the cause of the malfunction, perform troubleshooting for all related items.

·

Try to operate the vehicle under the conditions recorded in the freeze frame data which were present when the malfunction occurred. Confirm the data at this time and the data when the engine is idling (engine warmed up, no load, and shift lever in D or N) and compare these data with the freeze frame data.

·

Inspections take into account the fact that the malfunction may not have reoccurred and place emphasis on checking the vehicle conditions present at the time when the malfunction occurred.

·

When performing inspections, jiggle the relevant wire harnesses and connectors in an attempt to reproduce malfunctions that do not always occur.



Inspection flow:

Using freeze frame data, narrow down the parts to be inspected according to the vehicle conditions at the time when the malfunction occurred.


P1603:

A224366E07
0.219,0.775 1.114,1.107 0.895,0.332 10 While idling or while driving? 1.824,0.778 3.155,1.478 1.332,0.700 10 Did the engine speed decrease slowly or rapidly when engine stall occurred? 0.189,0.599 0.373,0.783 0.184,0.184 10 1: 1.824,0.599 2.007,0.783 0.184,0.184 10 2: 3.925,0.778 4.961,1.295 1.036,0.517 10 Was the air-fuel ratio abnormal or normal? 3.925,0.599 4.109,0.783 0.184,0.184 10 3: 5.961,0.75 6.904,0.915 0.943,0.165 10 Intake air leak 5.781,1.758 7.031,1.923 1.250,0.165 10 Sensor malfunction 1.242,5.833 2.492,5.998 1.250,0.165 10 Sensor malfunction 5.748,2.763 7.061,2.928 1.313,0.165 10 Fuel supply problem 1.214,7.822 2.527,7.987 1.313,0.165 10 Fuel supply problem 6.036,3.459 6.746,3.809 0.710,0.350 10 Air volume insufficient 5.953,4.47 6.878,4.802 0.924,0.332 10 Ignition timing incorrect 3.41,4.481 4.492,4.822 1.082,0.341 10 Injection and ignition stoppage 1.337,6.554 2.418,6.895 1.082,0.341 10 Injection and ignition stoppage 3.497,5.48 4.394,5.821 0.897,0.341 10 Load from external parts 1.31,0.134 1.697,0.299 0.387,0.165 10 Idling 0.096,2.544 0.557,2.709 0.461,0.165 10 Driving 2.972,0.134 4.156,0.299 1.184,0.165 10 Decreased Slowly 1.16,2.544 2.400,2.746 1.239,0.202 10 Decreased Rapidly 5.027,0.134 5.692,0.317 0.665,0.184 10 Abnormal 3.832,2.544 4.330,2.709 0.498,0.165 10 Normal

1:
·

If the engine stalled when the intake air volume was low (during idling or deceleration), there may be a decrease in torque due to an incorrect air-fuel ratio, etc.

·

If the engine stalled when the intake air volume was high (during driving or acceleration), there may be a major malfunction such as continuous misfire due to ignition stoppage, fuel injection stoppage, etc. and the torque drops to zero.


2:
·

If the engine speed decreased slowly, there may have been a decrease in torque due to an air-fuel ratio that was incorrect (by approximately 20 to 30%), etc.

·

If the engine speed decreased rapidly, there may have been a malfunction such as when the engine misfires almost continuously due to ignition stoppage, fuel injection stoppage, etc., or when the external load increases due to an external part malfunctioning.


3:
·

If the air-fuel ratio was abnormal, there may have been an intake air leak, sensor malfunction, or fuel supply problem.

·

If the air-fuel ratio was normal, the air volume may have been insufficient or the ignition timing may have been incorrect.


P1603 inspection flow: Narrow down the parts to be inspected according to the vehicle conditions at the time when the malfunction occurred (freeze frame data).

Vehicle State Engine Speed Suspected Area Primary Parts to Inspect Procedure
Idling or decelerating Slowly decreases and engine stalls Air-fuel ratio abnormal Air suction
·

Intake system connections

·

Purge VSV system

·

Brake booster


3 to 6
Sensor malfunction (value from sensor too lean)
·

Mass air flow meter

·

Engine coolant temperature sensor

·

Heated oxygen sensor system

·

Thermostat

·

Power supply circuit (heated oxygen sensor)


7 to 16
Sensor malfunction (value from sensor too rich) 25 to 34
Fuel supply problem
·

Fuel pump control system

·

Purge VSV system

·

Fuel line

·

ECM


17 to 24
Intake air volume insufficient ISC flow rate
·

Throttle with motor body assembly (ISC valve)


35 to 37
Excessive valve overlap
·

Camshaft timing oil control valve assembly


38
Ignition timing incorrect Does not operate as expected
·

Engine coolant temperature sensor

·

Mass air flow meter

·

Knock sensor


39 to 41
Rapidly decreases and engine stalls Ignition and injection stops (electrical system malfunction) Power temporarily cut
·

Power supply circuit (Fuel injector assembly, No. 1 ignition coil)


42, 43
External part malfunctioning Increase in load
·

Air conditioning system

·

Electrical load signal system

·

Power steering system

·

Automatic transaxle system

·

Park/neutral position switch assembly


46 to 49
Accelerating - Crankshaft position sensor, Camshaft position sensor malfunction Power temporarily cut
·

Check DTCs


1
Mass air flow meter Foreign matter adhesion
·

Mass air flow meter


51
Fuel supply problem Fuel leak, clog
·

Fuel pump control system

·

Fuel line


54 to 56
Ignition and injection stops (electrical system malfunction) Power temporarily cut
·

Power supply circuit (Fuel injector assembly, No. 1 ignition coil)


52, 53

P1605:

A224367E06
0.498,0.514 0.668,0.688 0.170,0.174 10 1: 0.498,0.71 1.640,1.213 1.142,0.503 10 Did the engine speed decrease slowly or rapidly? 2.819,0.514 2.989,0.688 0.170,0.174 10 2: 2.819,0.71 3.961,1.213 1.142,0.503 10 Was the air-fuel ratio abnormal or normal? 5.69,0.715 6.633,0.881 0.943,0.165 10 Intake air leak 5.549,1.727 6.788,1.892 1.239,0.165 10 Sensor malfunction 5.522,2.722 6.799,2.924 1.276,0.202 10 Fuel supply problem 4.034,2.065 4.742,2.384 0.708,0.319 10 Air volume insufficient 3.925,3.05 4.850,3.382 0.924,0.332 10 Ignition timing incorrect 1.582,2.706 2.673,3.057 1.091,0.350 10 Injection and ignition stoppage 1.662,3.707 2.586,4.057 0.924,0.350 10 Load from external parts 1.908,0.876 2.628,1.226 0.721,0.350 10 Decreased Slowly 0.264,1.847 0.984,2.197 0.721,0.350 10 Decreased Rapidly 4.299,0.894 4.945,1.059 0.647,0.165 10 Abnormal 2.776,1.847 3.293,2.012 0.517,0.165 10 Normal

1:
·

If the engine speed decreased slowly, there may have been a decrease in torque due to an air-fuel ratio that was incorrect (by approximately 20 to 30%), etc.

·

If the engine speed decreased rapidly, there may have been a malfunction such as when the engine misfires almost continuously due to ignition stoppage, fuel injection stoppage, etc., or when the external load increases due to an external part malfunctioning.


2:
·

If the air-fuel ratio was abnormal, there may have been an intake air leak, sensor malfunction, or fuel supply problem.

·

If the air-fuel ratio was normal, the air volume may have been insufficient or the ignition timing may have been incorrect.


P1605 inspection flow: Narrow down the parts to be inspected according to the vehicle conditions at the time when the malfunction occurred (freeze frame data).

Engine Speed Suspected Area Primary Parts to Inspect Procedure
Slowly decreases and engine stalls Air-fuel ratio abnormal Air suction
·

Intake system connections

·

Purge VSV system

·

Brake booster


3 to 6
Sensor malfunction (value from sensor too lean)
·

Mass air flow meter

·

Engine coolant temperature sensor

·

Heated oxygen sensor system

·

Thermostat

·

Power supply circuit (heated oxygen sensor)


7 to 16
Sensor malfunction (value from sensor too rich) 25 to 34
Fuel supply problem
·

Fuel pump control system

·

Purge VSV system

·

Fuel line

·

ECM


17 to 24
Intake air volume insufficient ISC flow rate
·

Throttle with motor body assembly (ISC valve)


35 to 37
Ignition timing incorrect Does not operate as expected
·

Knock sensor

·

Engine coolant temperature sensor

·

Mass air flow meter


39 to 41
Rapidly decreases and engine stalls Ignition and injection stops (electrical system malfunction) Power temporarily cut
·

Power supply circuit (Fuel injector assembly, No. 1 ignition coil)


42, 43
External part malfunctioning Increase in load
·

Air conditioning system

·

Electrical load signal system

·

Power steering system

·

Automatic transaxle system*1

·

Park/neutral position switch assembly*1


46 to 49

*1: for Automatic Transaxle

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.


e.

Read DTCs (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC P1603 and/or P1605 are output A
DTC P1603 or P1605 and other DTCs are output B



A

2.READ FREEZE FRAME DATA

B

2.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>DTC CHECK / CLEAR).

Result
Problem Symptom Freeze Frame Data Item Suspected Area Proceed to
Closed Throttle Position SW Engine Speed Total of Short FT and Long FT
When idling or decelerating, engine speed slowly decreases and engine stalls All 5 sets of freeze frame data are ON Decreases slowly*1 All 5 sets of freeze frame data are +15% or more*2
·

Air suction


·

Sensor malfunction (value from sensor too lean)


·

Fuel supply problem


A
At least 1 of the 5 sets of freeze frame data is -15% or less*3 Sensor malfunction (value from sensor too rich) B
All 5 sets of freeze frame data are between -15% and +15%
·

Intake air volume insufficient


·

Ignition timing incorrect


C
When idling or decelerating, engine speed rapidly decreases and engine stalls Decreases rapidly*1 -
·

Injection stoppage, ignition stoppage


·

Load from external parts


D
When accelerating or driving at constant speed, engine stalls*4 At least one is OFF - -
·

Sensor malfunction


·

Injection stoppage, ignition stoppage


·

Fuel supply problem


E

A215381E01
0.072,0.032 2.177,0.197 2.105,0.165 10 Rapid Decrease in Engine Speed 2.333,0.377 2.702,0.561 0.369,0.184 10 (rpm) 2.389,0.723 2.665,0.869 0.276,0.147 10 800 2.389,0.928 2.665,1.075 0.276,0.147 10 600 2.389,1.126 2.665,1.272 0.276,0.147 10 400 2.389,1.331 2.665,1.478 0.276,0.147 10 200 2.548,1.529 2.689,1.675 0.142,0.147 10 0 3.038,1.642 3.235,1.798 0.198,0.156 10 #1 3.472,1.642 3.670,1.798 0.198,0.156 10 #2 3.935,1.642 4.132,1.798 0.198,0.156 10 #3 4.153,1.642 4.350,1.798 0.198,0.156 10 #4 4.377,1.642 4.574,1.798 0.198,0.156 10 #5 4.985,1.105 6.058,1.261 1.073,0.156 10 400 rpm or more 1.216,1.019 2.122,1.203 0.906,0.184 10 Engine Speed 2.702,1.944 4.816,2.128 2.114,0.184 10 Freeze Frame Data Storage Point

HINT:
·

*1: A rapid decrease in engine speed may be caused by an electrical fault in the shared wiring of all or a number of cylinders, an increase in load from external parts, etc. The engine speed is considered to have decreased rapidly if either of the following conditions applies.

Otherwise, the engine speed is considered to have decreased slowly.

(a)

In the freeze frame data, the decrease in engine speed from #3 to #5 is 400 rpm or more.

(b)

In the freeze frame data, the engine speed at #5 is 120 rpm or less.



·

If the vehicle speed is 50 km/h (31 mph) or less and the difference between Engine Speed and SPD (NT) is 100 rpm or less, inspect the automatic transaxle. (Depending on the rate of vehicle deceleration, the engine speed may have decreased due to the A/T lock-up release being late.)

·

*2: When a DTC is stored, feedback compensation increases because the air-fuel ratio is determined to be lean.

·

*3: When a DTC is stored, feedback compensation decreases because the air-fuel ratio is determined to be rich.

·

*4: This item should be checked when DTC P1603 is output and is not necessary to check when only P1605 is output.





A

3.CHECK INTAKE SYSTEM

B

25.READ FREEZE FRAME DATA

C

35.READ FREEZE FRAME DATA

D

42.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR ASSEMBLY)

E

50.READ FREEZE FRAME DATA
3.CHECK INTAKE SYSTEM
a.

Check for air leaks in the intake system (vacuum hose disconnection, cracks, damaged gaskets, etc.) (See page Engine / Hybrid System>1NZ-FE INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION).

HINT:
·

If the accelerator pedal is released after racing the engine, the inspection is easier to perform because the vacuum inside the intake pipes increases and the air suction noise becomes louder.

·

If Short FT and Long FT are largely different from the normal values when idling (the intake air volume is small) and almost the same as the normal values when racing the engine (the intake air volume is high), air leakage may be present.



OK:

There is no air leaks.




OK

4.CHECK PURGE VSV

NG

REPAIR OR REPLACE INTAKE SYSTEM

4.CHECK PURGE VSV
a.
A258724E03
1.406,1.052 0.979,1.521 false 2.438,0.573 2.844,1.021 false 0.833,1.552 1.052,1.729 0.219,0.177 10 false *1 2.833,1.01 3.052,1.208 0.219,0.198 10 true *2

Disconnect the purge hose (on the canister side) of the purge VSV.


b.

Start the engine.

*1 Purge VSV
*2 Hose (Canister)


c.

Idle the engine.


d.

Disconnect the connector of the purge VSV.


e.

Check if air flows through the purge VSV.

OK:

Air does not flow.



f.

Reconnect the connector of the purge VSV.


g.

Reconnect the purge hose of the purge VSV.

HINT:

When this inspection is performed, the MIL may illuminate. After finishing the inspection, check and clear DTCs (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>DTC CHECK / CLEAR).




OK

5.READ FREEZE FRAME DATA

NG

5.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>FREEZE FRAME DATA).

Result
Freeze Frame Data Item Result Suspected Area Proceed to
Stop Light Switch At least 1 of the 5 sets of freeze frame data is ON Air suction from brake booster A
All 5 sets of freeze frame data are OFF - B



A

6.READ VALUE USING INTELLIGENT TESTER (SHORT FT #1)

B

7.READ FREEZE FRAME DATA
6.READ VALUE USING INTELLIGENT TESTER (SHORT FT #1)
A217928E01
0.214,0.569 0.925,0.739 0.711,0.170 10 Depressed 0.093,0.053 0.902,0.209 0.809,0.156 10 Brake Pedal 0.308,1.092 0.936,1.248 0.628,0.156 10 Released 0.114,1.834 0.881,1.989 0.767,0.156 10 Short FT #1 2.508,2.227 3.261,2.564 0.753,0.336 10 Change is 10% or less

a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Start the engine and warm it up until the engine coolant temperature stabilizes.

HINT:

The A/C switch and all accessory switches should be off.



d.

Idle the engine.


e.

Turn the tester on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List / Short FT #1.

Standard:

Short FT #1 changes by +10% or less.


Result
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C

HINT:
·

Even if the results are normal, the brake booster may have been malfunctioning. Continue this inspection procedure until step 24, and if there are no problems with other parts, replace the brake booster (refer to step 57).


·

When air leaks from the brake booster is present, the feedback compensation increases because the air-fuel ratio becomes lean.


·

It is also possible to perform the airtightness inspection to check the brake booster.





A

7.READ FREEZE FRAME DATA

B

REPLACE BRAKE BOOSTER (FOR LHD)

C

REPLACE BRAKE BOOSTER (FOR RHD)

7.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>DTC CHECK / CLEAR).

Result
Freeze Frame Data Item Result Suspected Area Proceed to
Calculate Load Below 90% of the current value of the vehicle*1 Mass air flow meter A
O2S B1S1 Below 0.45 V*2
·

Heated oxygen sensor

·

Wire harness or connector

·

Actual air-fuel ratio abnormal


B
Both freeze frame data items listed above Values are other than above - C

HINT:
·

Try to operate the vehicle under the conditions recorded in the freeze frame data which were present when the malfunction occurred. Confirm the data at this time and the data when the engine is idling (engine warmed up, no load, and shift lever in D or N) and compare these data with the freeze frame data.

·

*1: If the mass air flow meter is malfunctioning, the freeze frame data will show a low engine load value.

·

*2: If the heated oxygen sensor is malfunctioning and constantly outputs a value indicating the air-fuel ratio is lean, the actual air-fuel ratio will become rich and the engine may stall.





A

8.INSPECT MASS AIR FLOW METER

B

9.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME)

C

12.READ FREEZE FRAME DATA
8.INSPECT MASS AIR FLOW METER

b.

Check for foreign matter in the air flow passage of the mass air flow meter.

Result
Result Proceed to
Visible foreign matter is present A
Visible foreign matter is not present B

HINT:

Even if the results are normal, the mass air flow meter may have been malfunctioning. Continue this inspection procedure until step 24, and if there are no problems with other parts, replace the mass air flow meter (refer to step 57).




A

B

12.READ FREEZE FRAME DATA
9.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME)
a.
A254132E04
0.548,0.37 1.635,0.532 1.086,0.163 10 Injection Volume 1.038,0.819 1.534,0.968 0.496,0.149 10 +12% 1.073,1.162 1.558,1.301 0.486,0.139 10 -12% 0.219,1.856 2.672,2.040 2.453,0.184 10 Heated Oxygen Sensor Output Voltage 0.273,2.378 1.478,2.527 1.205,0.149 10 Higher than 0.5 V 0.694,2.769 1.475,2.911 0.781,0.142 10 Below 0.4 V

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the tester on.


d.

Warm up the engine.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume.


f.

Change the fuel injection volume using the tester, and monitor the voltage output of the heated oxygen sensors displayed on the tester.

Standard:
Tester Display Specified Condition
Control the Injection Volume (+12%) Heated oxygen sensor output voltage is higher than 0.5 V
Control the Injection Volume (-12%) Heated oxygen sensor output voltage is below 0.4 V


Result
Result Proceed to
Abnormal A
Normal B

HINT:
·

The heated oxygen sensor (sensor 1) has an output delay of a few seconds and the heated oxygen sensor (sensor 2) has a maximum output delay of approximately 20 seconds.

·

Even if the results are normal, the heated oxygen sensor may have been malfunctioning. Continue this inspection procedure until step 24, and if there are no problems with other parts, replace the heated oxygen sensor (refer to step 57).





A

10.CHECK TERMINAL VOLTAGE (POWER SOURCE OF HEATED OXYGEN SENSOR (SENSOR 1))

B

12.READ FREEZE FRAME DATA
10.CHECK TERMINAL VOLTAGE (POWER SOURCE OF HEATED OXYGEN SENSOR (SENSOR 1))
a.

Check the harnesses and connectors, referring to DTC P0031 inspection procedure (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>P0031).


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.




OK

11.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)

NG

REPAIR POWER SOURCE CIRCUIT (HEATED OXYGEN SENSOR (SENSOR 1) POWER SOURCE)

11.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
a.

Check the harnesses and connectors, referring to DTC P0171 inspection procedure (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>P0171).


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>FREEZE FRAME DATA).

Result
Freeze Frame Data Item Result Proceed to
Initial Engine Coolant Temp, Ambient Temperature, Initial Intake Air Temp Difference in temperature between each item is below 10°C*1 A
Difference in temperature between each item is 10°C or more*2 B

HINT:
·

*1: A long time had elapsed after stopping the engine.

·

*2: A long time had not elapsed after stopping the engine.





A

13.READ FREEZE FRAME DATA

B

15.READ FREEZE FRAME DATA
13.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>FREEZE FRAME DATA).

A217929E01
0.467,0.856 2.887,1.519 2.420,0.663 10 Engine Coolant Temperature Increase after Engine Start (Engine Coolant Temperature - Engine Coolant Temperature at Engine Start) 3.423,0.037 3.718,0.234 0.295,0.198 10 (°C) 5.609,2.116 6.223,2.286 0.614,0.170 10 (Minutes) 5.16,1.69 5.316,1.846 0.156,0.156 10 A 4.964,0.779 5.120,0.935 0.156,0.156 10 C 3.891,0.493 4.047,0.649 0.156,0.156 10 B 3.563,2.39 5.573,2.546 2.010,0.156 10 Time Elapsed after Engine Start

Result
Freeze Frame Data Item Result Suspected Area Proceed to
Initial Engine Coolant Temp, Coolant Temp, Engine Run Time Range A
·

Engine coolant temperature sensor

·

Thermostat


A
Range B Engine coolant temperature sensor B
Range C - C

HINT:

This step is not directly related to engine stall.




A

14.INSPECT THERMOSTAT

B

16.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

C

17.READ FREEZE FRAME DATA
14.INSPECT THERMOSTAT
a.

Result
Result Proceed to
Abnormal A
Normal B

HINT:

This step is not directly related to engine stall.



A

B

16.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
15.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>FREEZE FRAME DATA).

Result
Freeze Frame Data Item Result Suspected Area Proceed to
Coolant Temp 120°C or more Engine coolant temperature sensor A
Coolant Temp, Ambient Temperature Engine coolant temperature is lower than outside temperature by 15°C or more Engine coolant temperature sensor
Both freeze frame data items listed above Values are other than above - B



A

16.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

B

17.READ FREEZE FRAME DATA
16.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
a.

Inspect the engine coolant temperature sensor (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>ENGINE COOLANT TEMPERATURE SENSOR>INSPECTION).


Result
Result Proceed to
Abnormal A
Normal B

HINT:

Even if the results are normal, the engine coolant temperature sensor may have been malfunctioning. Continue this inspection procedure until step 24, and if there are no problems with other parts, replace the engine coolant temperature sensor (refer to step 57).



A

B

17.READ FREEZE FRAME DATA
17.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>FREEZE FRAME DATA).

Result
Freeze Frame Data Item Result Suspected Area Proceed to
EVAP (Purge) VSV At least 1 of the 5 sets of freeze frame data is not 0% Purge VSV A
All 5 sets of freeze frame data are 0% - B

HINT:

If the purge VSV is stuck closed, air-fuel ratio compensation by the purge VSV is incorrectly adjusted, and then the air-fuel ratio becomes lean and the engine may stall.




A

18.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE VSV FOR EVAP CONTROL)

B

22.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP/SPEED)
18.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE VSV FOR EVAP CONTROL)
a.
A257861E03
1.354,1.094 1.01,1.583 false 2.344,1.021 2.552,1.615 false 0.906,1.594 1.135,1.792 0.229,0.198 10 false *1 2.469,1.625 2.729,1.813 0.26,0.188 10 true *2

Disconnect the purge hose (on the canister side) of the purge VSV.


b.

Connect the intelligent tester to the DLC3.

Text in Illustration
*1 Purge VSV
*2 Hose (to canister)


c.

Turn the ignition switch to ON.


d.

Start the engine.


e.

Turn the tester on.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Evap Control.


g.

Operate the purge VSV and check the air flow.

OK:
Activate the VSV for Evap Control Specified Condition
ON Air flows
OFF Air does not flow


Result
Result Proceed to
Abnormal A
Normal B


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Even if the results are normal, the purge VSV may have been malfunctioning. Continue this inspection procedure until step 24, and if there are no problems with other parts, replace the purge VSV (refer to step 57).




A

19.INSPECT PURGE VSV

B

22.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP/SPEED)
19.INSPECT PURGE VSV

OK

20.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF PURGE VSV)

NG

20.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF PURGE VSV)
a.

Check the harnesses and connectors, referring to DTC P0443 inspection procedure (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>P0443).


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.




OK

21.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)

NG

REPAIR POWER SOURCE CIRCUIT (PURGE VSV POWER SOURCE)

21.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)
a.

Check the harnesses and connectors, referring to DTC P0443 inspection procedure (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>P0443).


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

22.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP/SPEED)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.


d.

When performing the Active Test, check for an operating sound from the fuel pump.

OK:
Control the Fuel Pump/Speed Specified Condition
ON Operating sound heard
OFF Operating sound not heard


Result
Result Proceed to
Abnormal A
Normal B

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

While performing the Active Test, make sure that there is no fuel leakage from the pipes, no signs that fuel has leaked, and no fuel smell.

·

If the fuel pump operating noise is abnormal, proceed to step 23.





A

23.INSPECT FUEL PUMP

B

24.CHECK FUEL SYSTEM
23.INSPECT FUEL PUMP
a.


OK

NG

24.CHECK FUEL SYSTEM
a.

Check for foreign matter such as iron particles around the fuel pump (fuel pump, fuel pump filter and inside the fuel tank), and for signs that the fuel pump was stuck.

Result
Result Proceed to
There is foreign matter or signs that fuel pump was stuck A
There is no foreign matter and no signs that fuel pump was stuck B

HINT:

If there is foreign matter such as iron particles on the fuel pump, fuel filter or fuel tank, remove the foreign matter.




A

REPAIR OR REPLACE FUEL SYSTEM

B

57.REPLACE MALFUNCTIONING PARTS
25.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>FREEZE FRAME DATA).

Result
Freeze Frame Data Item Result Suspected Area Proceed to
Calculate Load 110% or more of the current value of the vehicle*1 Mass air flow meter A
O2S B1S1 0.45 V or higher*2
·

Heated oxygen sensor

·

Harness and connector

·

Actual air-fuel ratio abnormal


B
Both freeze frame data items listed above Values are other than above - C

HINT:
·

Try to operate the vehicle under the conditions recorded in the freeze frame data which were present when the malfunction occurred. Confirm the data at this time and the data when the engine is idling (engine warmed up, no load, and shift lever in D or N) and compare these data with the freeze frame data.

·

*1: If the mass air flow meter is malfunctioning and incorrectly measures the intake air volume to be higher than the actual volume of air flowing through the intake manifold, the freeze frame data will show a high engine load value.

·

*2: As the heated oxygen sensor output is low before the sensor warms up, the value at that time cannot be used for diagnosis. If the heated oxygen sensor is malfunctioning and constantly outputs a value indicating the air-fuel ratio is rich, the actual air-fuel ratio will become lean and the engine may stall.





A

26.INSPECT MASS AIR FLOW METER

B

27.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME)

C

30.READ FREEZE FRAME DATA
26.INSPECT MASS AIR FLOW METER
a.

Remove the mass air flow meter.


b.

Check for foreign matter in the air flow passage of the mass air flow meter.

Result
Result Proceed to
Visible foreign matter is present A
Visible foreign matter is not present B


HINT:

Even if the results are normal, the mass air flow meter may have been malfunctioning. Continue this inspection procedure until step 34, and if there are no problems with other parts, replace the mass air flow meter (refer to step 57).



A

B

30.READ FREEZE FRAME DATA
27.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME)
a.
A254132E05
0.548,0.37 1.635,0.532 1.086,0.163 10 Injection Volume 1.18,0.819 1.690,0.968 0.510,0.149 10 +12% 1.18,1.162 1.666,1.301 0.486,0.139 10 -12% 0.219,1.856 2.672,2.040 2.453,0.184 10 Heated Oxygen Sensor Output Voltage 0.273,2.378 1.478,2.527 1.205,0.149 10 Higher than 0.5 V 0.694,2.769 1.475,2.911 0.781,0.142 10 Below 0.4 V

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the tester on.


d.

Warm up the engine.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume.


f.

Change the fuel injection volume using the tester, and monitor the voltage output of the heated oxygen sensors displayed on the tester.

Standard:
Tester Display Specified Condition
Control the Injection Volume (12%) Heated oxygen sensor output voltage is higher than 0.5 V
Control the Injection Volume (-12%) Heated oxygen sensor output voltage is below 0.4 V


Result
Result Proceed to
Abnormal A
Normal B

HINT:
·

The heated oxygen sensor (sensor 1)has an output delay of a few seconds and the heated oxygen sensor (sensor 2) has a maximum output delay of approximately 20 seconds.

·

Even if the results are normal, the heated oxygen sensor may have been malfunctioning. Continue this inspection procedure until step 34, and if there are no problems with other parts, replace the heated oxygen sensor (refer to step 57).





A

28.CHECK TERMINAL VOLTAGE (POWER SOURCE OF HEATED OXYGEN SENSOR)

B

30.READ FREEZE FRAME DATA
28.CHECK TERMINAL VOLTAGE (POWER SOURCE OF HEATED OXYGEN SENSOR)
a.

Check the harnesses and connectors, referring to DTC P0031 inspection procedure (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>P0031).


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.




OK

29.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)

NG

REPAIR POWER SOURCE CIRCUIT (HEATED OXYGEN SENSOR POWER SOURCE)

29.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
a.

Check the harnesses and connectors, referring to DTC P0171 inspection procedure (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>P0171).


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

30.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>FREEZE FRAME DATA).

Result
Freeze Frame Data Item Result Proceed to
Initial Engine Coolant Temp, Ambient Temperature, Initial Intake Air Temp Difference in temperature between each item is below 10°C*1 A
Difference in temperature between each item is 10°C or more*2 B

HINT:
·

*1: A long time had elapsed after stopping the engine.

·

*2: A long time had not elapsed after stopping the engine.





A

31.READ FREEZE FRAME DATA

B

33.READ FREEZE FRAME DATA
31.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Using the tester, confirm the vehicle conditions present when the DTC was stored which are recorded in the freeze frame data (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>FREEZE FRAME DATA).

A217929E01
0.467,0.856 2.887,1.519 2.420,0.663 10 Engine Coolant Temperature Increase after Engine Start (Engine Coolant Temperature - Engine Coolant Temperature at Engine Start) 3.423,0.037 3.718,0.234 0.295,0.198 10 (°C) 5.609,2.116 6.223,2.286 0.614,0.170 10 (Minutes) 5.16,1.69 5.316,1.846 0.156,0.156 10 A 4.964,0.779 5.120,0.935 0.156,0.156 10 C 3.891,0.493 4.047,0.649 0.156,0.156 10 B 3.563,2.39 5.573,2.546 2.010,0.156 10 Time Elapsed after Engine Start

Result
Freeze Frame Data Item Result Suspected Area Proceed to
Initial Engine Coolant Temp, Coolant Temp, Engine Run Time Range A
·

Engine coolant temperature sensor

·

Thermostat


A
Range B Engine coolant temperature B
Range C - C

HINT:

This step is not directly related to engine stall.




A

32.INSPECT THERMOSTAT

B

34.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

C

58.CLEAR DTC
32.INSPECT THERMOSTAT
a.

Result
Result Proceed to
Abnormal A
Normal B

HINT:

This step is not directly related to engine stall.



A

B

34.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
33.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>FREEZE FRAME DATA).

Result
Freeze Frame Data Item Result Suspected Area Proceed to
Coolant Temp 120°C or higher Engine coolant temperature sensor A
Coolant Temp, Ambient Temperature Engine coolant temperature is lower than outside temperature by 15°C or more Engine coolant temperature sensor
Both freeze frame data items listed above Values are other than above - B



A

34.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

B

58.CLEAR DTC
34.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
a.

Inspect the engine coolant temperature sensor (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>ENGINE COOLANT TEMPERATURE SENSOR>INSPECTION).


Result
Result Proceed to
Abnormal A
Normal B

HINT:

Even if the results are normal, the engine coolant temperature sensor may have been malfunctioning. If there are no problems with other parts, replace the engine coolant temperature sensor (refer to step 57).



A

B

57.REPLACE MALFUNCTIONING PARTS
35.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>FREEZE FRAME DATA).

Result
Freeze Frame Data Item Result Suspected Area Proceed to
Total of ISC Learning Value and ISC Feedback Value Below 80% of the current value of the vehicle*1 Throttle with motor body assembly A
120% or more of the current value of the vehicle*2 B
From 80 to 120% of the current value of the vehicle - C

HINT:
·

Try to operate the vehicle under the conditions recorded in the freeze frame data which were present when the malfunction occurred. Confirm the data at this time and the data when the engine is idling (engine warmed up, no load, and shift lever in D or N) and compare these data with the freeze frame data.

·

*1: If the throttle with motor body assembly has a temporary problem in which it cannot fully close, the intake air volume and engine speed increase. As a result, the ISC learning amount becomes less than the standard. At this time, if the throttle with motor body assembly returns to normal and fully closes, the intake air volume will be insufficient and the engine may stall.

·

*2: If carbon accumulates on the throttle with motor body assembly and the intake air volume decreases, the ISC learning amount is increased to maintain the idling speed. If this situation continues, the ISC learning amount reaches the upper limit, the idling speed cannot be maintained causing idling to become unstable, and the engine may stall.





A

36.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY

B

37.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY

C

38.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE VVT LINEAR)
36.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY
a.

Check for foreign matter and signs that the throttle with motor body assembly was stuck, and also check that the valve and shaft move smoothly during operation.

Result
Result Proceed to
Abnormal A
Normal B

HINT:

Even if the results are normal, the throttle with motor body assembly may have been malfunctioning. Continue this inspection procedure until step 41, and if there are no problems with other parts, replace the throttle with motor body assembly (refer to step 57).




A

REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY

B

38.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE VVT LINEAR)
37.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY
a.

Check if carbon is in the air flow passage of the throttle with motor body assembly.

Result
Result Proceed to
Carbon in passage A
No carbon in passage B

HINT:

Even if the results are normal, the throttle with motor body assembly may have been malfunctioning. Continue this inspection procedure until step 41, and if there are no problems with other parts, replace the throttle with motor body assembly (refer to step 57).




A

REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY

B

38.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE VVT LINEAR)
38.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE VVT LINEAR)
a.

Perform the Active Test, referring to DTC P0011 inspection procedure (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>P0011).

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

When the results of the inspection using the Active Test are normal but the valve operating noise is abnormal, check the valve for any signs of problems.





OK

39.READ FREEZE FRAME DATA

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

39.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>FREEZE FRAME DATA).

Result
Freeze Frame Data Item Suspected Area Proceed to
IGN Advance Knock Correct Learn Value
Differs from the current value of the vehicle by 10° or more Below 3°
·

Engine coolant temperature sensor

·

Mass air flow meter

·

Knock sensor


A
3° or more - B
Differs from the current value of the vehicle by less than 10° - -

HINT:
·

Try to operate the vehicle under the conditions recorded in the freeze frame data which were present when the malfunction occurred. Confirm the data at this time and the data when the engine is idling (engine warmed up, no load, and shift lever in D or N) and compare these data with the freeze frame data.

·

Even if the results are normal, the knock sensors may have been malfunctioning. If there are no problems with other parts, replace the knock sensors (refer to step 57).





A

40.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

B

57.REPLACE MALFUNCTIONING PARTS
40.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
a.

Inspect the engine coolant temperature sensor (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>ENGINE COOLANT TEMPERATURE SENSOR>INSPECTION).



OK

41.INSPECT MASS AIR FLOW METER (INTAKE AIR TEMPERATURE SENSOR)

NG

41.INSPECT MASS AIR FLOW METER (INTAKE AIR TEMPERATURE SENSOR)
a.

Inspect the mass air flow meter (intake air temperature sensor) (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>MASS AIR FLOW METER>INSPECTION).



OK

NG

42.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR ASSEMBLY)
a.

Check the harnesses and connectors, referring to DTC P0300 inspection procedure (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>P0300).


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.

·

A rapid decrease in engine speed may have been caused by a malfunction in all or multiple cylinders. (There may be an electrical malfunction in the wiring shared by all the cylinders.)




OK

43.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IGNITION COIL NO. 1)

NG

43.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IGNITION COIL NO. 1)
a.

Check the harnesses and connectors, referring to DTC P0351 inspection procedure (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>P0351).


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.

·

A rapid decrease in engine speed may have been caused by a malfunction in all or multiple cylinders. (There may be an electrical malfunction in the wiring shared by all the cylinders.)




OK

44.READ FREEZE FRAME DATA

NG

REPAIR POWER SOURCE CIRCUIT (NO. 1 IGNITION COIL POWER SOURCE)

44.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>FREEZE FRAME DATA).

Result
Freeze Frame Data Item Result Suspected Area Proceed to
Idle Spark Advn Ctrl (#1 to #4) At least one cylinder shows a value of 4° or more
·

Fuel injector system

·

Ignition coil system


A
All cylinders show a value of less than 4° - B



A

45.READ FREEZE FRAME DATA

B

46.READ FREEZE FRAME DATA
45.READ FREEZE FRAME DATA
a.

Change the location of the ignition coil No. 1 for the cylinder whose Idle Spark Advn Ctrl (#1 to #4) was 4° or more in step 44.


b.

Connect the intelligent tester to the DLC3.


c.

Start the engine.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Idle Spark Advn Ctrl (#1 to #4).

Result
Result Proceed to
Same as result in step 44 A
Different from result in step 44 B

HINT:

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.




A

46.READ FREEZE FRAME DATA

B

46.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>FREEZE FRAME DATA).

Result
Freeze Frame Data Item Suspected Area Proceed to
A/C Signal Air Conditioner FB Val Power Steering Signal
A/C Signal display changes from OFF to ON Value displayed for Air Conditioner FB Val increases Does not change from OFF A/C system A*1
B*2
Changes from OFF to ON Power steering system C*3
D*4
A/C Signal display does not change from OFF Value displayed for Air Conditioner FB Val does not increase Changes from OFF to ON
Does not change from OFF -

*1: for Automatic Air Conditioning.

*2: for Manual Air Conditioning.

*3: for Automatic Transaxle.

*4: for Manual Transaxle.


HINT:
·

Try to operate the vehicle under the conditions recorded in the freeze frame data which were present when the malfunction occurred. Confirm the data at this time and the data when the engine is idling (engine warmed up, no load, and shift lever in D or N) and compare these data with the freeze frame data.

·

The normal value for the ISC learning amount is engine displacement (liters) x 0.9.

·

Even if the results are normal, the power steering system may have been malfunctioning. Continue this inspection procedure until step 48 (or step 49), and if there are no problems with other parts, inspect the power steering system (refer to step 57).





A

B

CHECK AIR CONDITIONING SYSTEM (FOR MANUAL AIR CONDITIONING)

C

47.READ FREEZE FRAME DATA

D

49.READ FREEZE FRAME DATA
47.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>FREEZE FRAME DATA).

Result
Freeze Frame Data Item Suspected Area Proceed to
Electrical Load Signal Electric Load Feedback Val Difference between Engine Speed and Turbine Speed Vehicle Speed
Electrical Load Signal display changes from OFF to ON*1, or Value displayed for Electric Load Feedback Val increases*1 Value displayed for Electric Load Feedback Val changes - - Electrical load signal circuit A
Value displayed for Electric Load Feedback Val does not change At least 1 of the 5 sets of freeze frame data is below 100 rpm Below 50 km/h (31 mph) Automatic transaxle system B
50 km/h (31 mph) or more - C
All 5 sets of freeze frame data are 100 rpm or more - - C
Electrical Load Signal display does not change from OFF, or Value displayed for Electric Load Feedback Val does not increase - At least 1 of the 5 sets of freeze frame data is below 100 rpm Below 50 km/h (31 mph) Automatic transaxle system B
50 km/h (31 mph) or more - C
All 5 sets of freeze frame data are 100 rpm or more - - C

HINT:
·

*1: If the Electrical Load Signal display changes from OFF to ON or the "Electric Load Feedback Val" increases, it probably is a malfunction due to a change in electrical load. Check the generator and the continuity and connections between the generator and ECM.

·

If the vehicle speed is 50 km/h (31 mph) or less and the difference between Engine Speed and SPD (NT) is 100 rpm or less, inspect the automatic transaxle. (Depending on the rate of vehicle deceleration, the engine speed may have decreased due to the A/T lock-up release being late.)

·

The normal value for the ISC learning amount is engine displacement (liters) x 0.9.

·

Even if the results are normal, the electrical load signal system and/or the automatic transaxle system may have been malfunctioning. Continue this inspection procedure until step 48, and if there are no problems with other parts, inspect the electrical load system and/or the automatic transaxle system (refer to step 57).





A

B

CHECK AUTOMATIC TRANSAXLE SYSTEM

C

48.READ FREEZE FRAME DATA
48.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>FREEZE FRAME DATA).

Result
Freeze Frame Data Item Suspected Area Proceed to
Shift SW Status (P or N) Neutral Position SW Signal
P and N position are both OFF in at least one data set ON when Shift SW Status D or R Park/neutral position switch assembly A
OFF when Shift SW Status D or R Automatic transaxle system B
All 5 sets of freeze frame data are ON - - C

HINT:

Even if the results are normal, the park/neutral position switch assembly and/or automatic transaxle system may have been malfunctioning. If there are no problems with other parts, inspect the park/neutral position switch assembly and/or automatic transaxle system (refer to step 57).




A

CHECK PARK/NEUTRAL POSITION SWITCH ASSEMBLY

B

CHECK AUTOMATIC TRANSAXLE SYSTEM

C

57.REPLACE MALFUNCTIONING PARTS
49.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>FREEZE FRAME DATA).

Result
Freeze Frame Data Item Suspected Area Proceed to
Electrical Load Signal
Electric Load Feedback Val
Electrical Load Signal display changes from OFF to ON*1, or Value displayed for Electric Load Feedback Val increases*1 Electrical load signal circuit A
Electrical Load Signal display does not change from OFF, or Value displayed for Electric Load Feedback Val does not increase - B

HINT:
·

*1: If the Electrical Load Signal display changes from OFF to ON or the "Electric Load Feedback Val" increases, it probably is a malfunction due to a change in electrical load. Check the generator and the continuity and connections between the generator and ECM.

·

The normal value for the ISC learning amount is engine displacement (liters) x 0.9.

·

Even if the results are normal, the electrical load signal system may have been malfunctioning. If there are no problems with other parts, inspect the electrical load system (refer to step 57).





A

B

57.REPLACE MALFUNCTIONING PARTS
50.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>FREEZE FRAME DATA).

Result
Freeze Frame Data Item Result Suspected Area Proceed to
Throttle Sensor Position, Calculate Load Calculate Load decreases while Throttle Sensor Position increases Mass air flow meter A
Calculate Load does not decrease while Throttle Sensor Position increases - B



A

51.INSPECT MASS AIR FLOW METER

B

52.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR ASSEMBLY)
51.INSPECT MASS AIR FLOW METER
a.

Remove the mass air flow meter.


b.

Check for foreign matter in the air flow passage of the mass air flow meter.

Result
Result Proceed to
Visible foreign matter is present A
Visible foreign matter is not present B


c.

Install the mass air flow meter.

HINT:

Even if the results are normal, the mass air flow meter may have been malfunctioning. Continue this inspection procedure until step 56, and if there are no problems with other parts, replace the mass air flow meter (refer to step 57).




A

B

52.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR ASSEMBLY)
52.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR ASSEMBLY)
a.

Check the harnesses and connectors, referring to DTC P0300 inspection procedure (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>P0300).


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.

·

A rapid decrease in engine speed may have been caused by a malfunction in all or multiple cylinders. (There may be an electrical malfunction in the wiring shared by all the cylinders.)




OK

53.CHECK TERMINAL VOLTAGE (POWER SOURCE OF NO. 1 IGNITION COIL)

NG

53.CHECK TERMINAL VOLTAGE (POWER SOURCE OF NO. 1 IGNITION COIL)
a.

Check the harnesses and connectors, referring to DTC P0351 inspection procedure (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>P0351).


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.

·

A rapid decrease in engine speed may have been caused by a malfunction in all or multiple cylinders. (There may be an electrical malfunction in the wiring shared by all the cylinders.)




OK

54.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP/SPEED)

NG

REPAIR POWER SOURCE CIRCUIT (NO. 1 IGNITION COIL POWER SOURCE)

54.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP/SPEED)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.


e.

When performing the Active Test, check for an operating sound from the fuel pump.

OK:
Control the Fuel Pump/Speed Specified Condition
ON Operating sound heard
OFF Operating sound not heard


Result
Result Proceed to
Abnormal A
Normal B

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

While performing the Active Test, make sure that there is no fuel leakage from the pipes, no signs that fuel has leaked, and no fuel smell.

·

If the fuel pump operating noise is abnormal, proceed to step 55.





A

55.INSPECT FUEL PUMP

B

56.CHECK FUEL SYSTEM
55.INSPECT FUEL PUMP
a.


OK

NG

56.CHECK FUEL SYSTEM
a.

Check for foreign matter such as iron particles around the fuel pump (fuel pump, fuel pump filter and inside the fuel tank), and for signs that the fuel pump was stuck.

Result
Result Proceed to
There is foreign matter or signs that fuel pump was stuck A
There is no foreign matter and no signs that fuel pump was stuck B



A

REPAIR OR REPLACE FUEL SYSTEM

B

57.REPLACE MALFUNCTIONING PARTS
57.REPLACE MALFUNCTIONING PARTS
a.

If the malfunction could not be identified in steps 3 to 24, replace the part which is suspected to be malfunctioning according to the step where an inspection was performed.

Performed Step Inspection or Part to Replace
Step 6 Brake booster replacement
Step 8 Mass air flow meter replacement
Step 9 Heated oxygen sensor replacement
Step 16 Engine coolant temperature sensor replacement
Step 18 Purge VSV replacement
Step 24 Fuel pump replacement


b.

If the malfunction could not be identified in steps 25 to 34, replace the part which is suspected to be malfunctioning according to the step where an inspection was performed.

Performed Step Inspection or Part to Replace
Step 26 Mass air flow meter replacement
Step 27 Heated oxygen sensor replacement
Step 34 Engine coolant temperature sensor replacement


c.

If the malfunction could not be identified in steps 35 to 41, replace the part which is suspected to be malfunctioning according to the step where an inspection was performed.

Performed Step Inspection or Part to Replace
Step 36, 37 Throttle with motor body assembly replacement
Step 39 Knock sensor replacement


d.

If the malfunction could not be identified in steps 42 to 49, inspect and repair the part which is suspected to be malfunctioning according to the step where an inspection was performed.

Performed Step Inspection or Part to Replace
Step 46 A/C system inspection and repair
Power steering system inspection and repair
Step 47 or 49 Automatic transaxle system inspection and repair
Electrical load system inspection and repair
Step 48 Park/neutral position switch assembly inspection and repair
Automatic transaxle system inspection and repair


e.

If the malfunction could not be identified in steps 50 to 56, replace the part which is suspected to be malfunctioning according to the step where an inspection was performed.

Performed Step Inspection or Part to Replace
Step 51 Mass air flow meter replacement

HINT:

Referring to the chart, inspect and repair or replace the part from the step where an inspection was performed.




NEXT

58.CLEAR DTC
58.CLEAR DTC
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.




NEXT

59.PERFORM CONFIRMATION DRIVING PATTERN
59.PERFORM CONFIRMATION DRIVING PATTERN
a.

Check if engine stall symptoms are present.

HINT:

If any engine stall symptoms are present, recheck for DTCs and freeze frame data and perform an inspection.




OK

END

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS