35150B
1.INSTALL TRANSMISSION CASE PLUG ASSEMBLY
After replacing the continuously variable transaxle assembly, perform the following procedure.
Apply a light coat of Toyota Genuine CVT fluid FE to the 2 O-rings of 2 new transmission case plug assemblies.
Install the 2 transmission case plug assemblies to the continuously variable transaxle assembly.
Make sure that the O-rings are not damaged or do not jump out of position during installation.
35141D
2.INSTALL BREATHER PLUG HOSE
Perform this procedure only when replacement of the breather plug hose is necessary.
Install the No. 1 breather plug to the breather plug hose.
Install the breather plug hose with the No. 1 breather plug to the continuously variable transaxle assembly.
Engage the clamp and install the breather hose clamp to the breather plug hose.
3.INSTALL WIRE HARNESS CLAMP BRACKET
Install the 4 wire harness clamp brackets to the continuously variable transaxle assembly with the 5 bolts.
Engage the breather hose clamp and install the breather plug hose to the wire harness clamp bracket.
33823
4.INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET
Install the No. 1 transmission control cable bracket to the continuously variable transaxle assembly with the 2 bolts.
30400E
5.INSTALL CVT OIL PUMP TYPE T OIL SEAL
Ensure that there is no dirt or foreign matter on your hands, and then apply MP grease to the entire periphery of the lip of a new CVT oil pump type T oil seal.
Temporarily attach the CVT oil pump type T oil seal by pressing it onto the installation surface of the oil pump housing manually.
| *a | Drive in Depth |
Clean the oil seal contact section of SST and the area around it.
Using SST, drive the CVT oil pump type T oil seal in evenly, until it is even with the side surface of the oil pump housing.
-0.2 to 0.2 mm (-0.00787 to 0.00787 in.)
Drive the CVT oil pump type T oil seal in gradually, while visually checking the parallelism.
After the installation, confirm that the CVT oil pump type T oil seal has been driven in until it is even with the side surface of the oil pump housing.
Wipe any extra grease off with your hand.
32000A
6.INSTALL TORQUE CONVERTER ASSEMBLY
| *a | Matchmark |
| *b | Wide Groove |
| *c | Narrow Groove |
Turn the front oil pump drive gear so that the groove is at the top and place a matchmark on the housing to indicate the position of the groove.
Place the matchmark on the housing to indicate the position of the wide groove.
The matchmark position must be correct to prevent damage.
| *a | Key |
| *b | Matchmark |
Place a matchmark on the torque converter assembly so that the position of its key is clearly indicated.
| *1 | CVT Oil Pump Type T Oil Seal |
| *a | Matchmark |
Align the matchmark on the housing with the one on the torque converter assembly and engage the splines of the input shaft with the turbine runner splines.
Install the torque converter assembly to the input shaft while keeping it horizontal.
Do not damage the CVT oil pump type T oil seal.
| *1 | CVT Oil Pump Type T Oil Seal |
| *a | Matchmark |
Rotate the torque converter assembly approximately 180° and engage the splines of the stator shaft with the stator assembly.
Install the torque converter assembly to the input shaft while keeping it horizontal.
Do not damage the CVT oil pump type T oil seal.
| *1 | CVT Oil Pump Type T Oil Seal |
| *a | Matchmark |
Rotate the torque converter assembly approximately 180° again, align the matchmark on the torque converter assembly with the one on the housing and insert the key of the torque converter assembly into the groove of the front oil pump drive gear.
Do not push the torque converter assembly excessively when rotating it.
Install the torque converter assembly to the input shaft while keeping it horizontal.
Do not damage the CVT oil pump type T oil seal.
Clean the drive plate and torque converter assembly setting bolt holes.
| *a | Engine Surface |
| *b | Drive Plate Surface |
Using a vernier caliper and straightedge, measure dimension "A" between the continuously variable transaxle assembly contact surface of the engine assembly*a and the torque converter assembly contact surfaces of the drive plate*b.
Using a vernier caliper and straightedge, measure dimension "B" shown in the illustration and check that dimension "B" is more than dimension "A", which was measured in the previous step.
B = A + 1 mm (0.0394 in.) or more
Make sure to deduct the thickness of the straightedge.
If the continuously variable transaxle assembly is installed to the engine assembly with the torque converter assembly not sufficiently inserted, the torque converter assembly may be damaged.
Do not include the thickness of the set block.
30400
7.INSTALL CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
| *1 | Crankshaft |
| *2 | Torque Converter Assembly Centerpiece |
|
Clutch Spline Grease |
Apply clutch spline grease to the surface of the crankshaft that contacts the torque converter assembly centerpiece.
Toyota Genuine Clutch Spline Grease or equivalent
Approximately 1 g (0.0353 oz.)
| *1 | Knock Pin |
Confirm that the 2 knock pins are installed on the engine assembly and are not damaged.
Install the continuously variable transaxle assembly to the engine assembly with the 8 bolts.
Make sure that the wire harness or similar items are not pinched between the contact surfaces.
Do not forcibly pry on the continuously variable transaxle assembly.
When mounting the continuously variable transaxle assembly to the engine assembly, make sure to securely fit the knock pins into the knock holes.
Check that the torque converter assembly rotates.
When tightening the bolts, be sure that the mating surfaces of the engine assembly and continuously variable transaxle assembly are in close contact with one another.
Bolt length:
Bolt A: 45 mm (1.77 in.)
Bolt B: 35 mm (1.38 in.)
| *a | Adhesive |
Clean and degrease the bolts and installation holes in the engine mounting bracket LH.
Apply adhesive to 2 or 3 threads on the ends of the 4 bolts.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
To prevent contamination by foreign matter, install immediately after applying adhesive.
| *a | Temporarily Tighten |
Install the engine mounting bracket LH to the continuously variable transaxle assembly with the 4 bolts in the order shown in the illustration.
| *a | Temporarily Tighten |
Install the engine mounting insulator LH to the body with the 5 bolts in the order shown in the illustration.
Install the engine mounting bracket LH to the engine mounting insulator LH with the bolt and nut.
Turn the bolt while holding the nut.
12364B
8.INSTALL NO. 2 ENGINE MOVING CONTROL ROD
Temporarily install the No. 2 engine moving control rod to the continuously variable transaxle assembly with the 3 bolts.
Bolt length:
Bolt A: 25 mm (0.984 in.)
Bolt B: 33.5 mm (1.32 in.)
| *a | Temporarily Tighten |
Tighten the 3 bolts in the order shown in the illustration.
51201
9.INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
32101G
10.INSTALL DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT
| *a | Adhesive |
Remove any adhesive remaining in the 6 drive plate and torque converter assembly setting bolts.
Apply a few drops of adhesive to 2 or 3 threads at the tips of the 6 drive plate and torque converter assembly setting bolts.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
To prevent contamination by foreign matter, install immediately after applying adhesive.
Turn the crankshaft to gain access to the installation locations of the 6 drive plate and torque converter assembly setting bolts and install each bolt while holding the crankshaft pulley with SST.
First install the black-colored bolt, and then the remaining 5 silver-colored bolts.
Do not start the engine for at least 1 hour after installing the drive plate and torque converter assembly setting bolts.
82121
11.CONNECT ENGINE WIRE
Install the wire harness clamp bracket to the continuously variable transaxle assembly with the bolt.
Install the engine wire to the continuously variable transaxle assembly with the bolt.
Engage the 8 clamps and install the engine wire to the continuously variable transaxle assembly.
Connect the 6 connectors to the continuously variable transaxle assembly.
16260
12.CONNECT WATER BY-PASS HOSE ASSEMBLY
| *a | View A |
| *b | Front of Vehicle |
| *c | Left of Vehicle |
| *d | Blue Mark |
Engage the 2 clamps to install the water by-pass hose assembly to the continuously variable transaxle assembly.
Connect the 2 water by-pass hoses to the transmission oil cooler and slide the 2 hose clips to secure them as shown in the illustration.
Fully insert the 2 water by-pass hoses until the 2nd rib on each transmission oil cooler pipe.
Perform the installation with the hose clips at the correct directions.
35141F
13.INSTALL NO. 1 BREATHER PLUG
Engage the clamp and install the No. 1 breather plug to the hose clamp.
11363A
14.INSTALL FLYWHEEL HOUSING SIDE COVER
28100
15.INSTALL STARTER ASSEMBLY
16.INSTALL FRONT DRIVE SHAFT ASSEMBLIES
43498A
17.INSTALL NO. 1 DRIVE SHAFT HEAT INSULATOR
17410
18.INSTALL FRONT EXHAUST PIPE ASSEMBLY (for TMMIN Made)
17410
19.INSTALL FRONT EXHAUST PIPE ASSEMBLY (for TMT Made)
57533B
20.INSTALL FRONT FLOOR CENTER BRACE (for TMMIN Made)
57533B
21.INSTALL FRONT FLOOR CENTER BRACE (for TMT Made)
45025D
22.INSTALL NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY
23.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
45209
24.INSTALL STEERING SLIDING YOKE SUB-ASSEMBLY
for TMMIN Made:
Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY(for TMMIN Made)>INSTALLATION
for TMT Made:
Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY(for TMT Made)>INSTALLATION
45259A
25.INSTALL COLUMN HOLE COVER SILENCER SHEET
for TMMIN Made:
Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY(for TMMIN Made)>INSTALLATION
for TMT Made:
Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY(for TMT Made)>INSTALLATION
33820B
26.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
58810J
27.INSTALL CONSOLE BOX ASSEMBLY (for TMT Made)
58839A
28.INSTALL CONSOLE BOX HOLE COVER (for TMT Made)
58916
29.INSTALL BOX BOTTOM MAT (for TMT Made)
58912C
30.INSTALL NO. 2 SIDE BOX PANEL (for TMT Made)
58911A
31.INSTALL NO. 1 SIDE BOX PANEL (for TMT Made)
58817A
32.INSTALL NO. 2 FRONT CONSOLE BOX INSERT (for TMT Made)
58816D
33.INSTALL NO. 1 FRONT CONSOLE BOX INSERT (for TMT Made)
for LHD:
Click hereVehicle Interior>INTERIOR PANELS / TRIM>UPPER INSTRUMENT PANEL>INSTALLATION
for RHD:
Click hereVehicle Interior>INTERIOR PANELS / TRIM>LOWER INSTRUMENT PANEL>INSTALLATION
58910C
34.INSTALL REAR CONSOLE BOX ASSEMBLY (for Integrated Type)
58910C
35.INSTALL REAR CONSOLE BOX ASSEMBLY (for Separate Type)
74410
36.INSTALL BATTERY CARRIER ASSEMBLY
74431
37.INSTALL BATTERY TRAY
28800
38.INSTALL BATTERY
17701
39.INSTALL AIR CLEANER CASE SUB-ASSEMBLY
17801
40.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
41.INSTALL AIR CLEANER CAP SUB-ASSEMBLY
17880
42.INSTALL AIR CLEANER HOSE ASSEMBLY
43.INSTALL FRONT WHEELS
44.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
45.ADD ENGINE COOLANT
46.ADD CONTINUOUSLY VARIABLE TRANSAXLE FLUID
47.INSPECT FOR COOLANT LEAK
48.INSPECT FOR CONTINUOUSLY VARIABLE TRANSAXLE FLUID LEAK
49.INSPECT FOR EXHAUST GAS LEAK
Perform "Inspection After Repairs" after repairing gas leaks in the exhaust system.
Click hereEngine / Hybrid System>1NR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
50.INSPECT SHIFT LEVER POSITION
51.ADJUST SHIFT LEVER POSITION
51441C
52.INSTALL ENGINE UNDER COVER RH (w/o Metal Type Under Cover)
51442C
53.INSTALL ENGINE UNDER COVER LH (w/o Metal Type Under Cover)
51405A
54.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (w/ Metal Type Under Cover)
51451A
55.INSTALL CENTER ENGINE UNDER COVER (w/ Metal Type Under Cover)
56.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
57.RESET MEMORY