When the engine misfires, high concentrations of hydrocarbons (HC) enter the exhaust gas. Extremely high hydrocarbon concentration levels can cause an increase in exhaust emission levels. Extremely high concentrations of hydrocarbons can also cause increases in the three-way catalytic converter temperature, which may cause damage to the three-way catalytic converter. To prevent this increase in emissions and to limit the possibility of thermal damage, the ECM monitors the misfire count. When the temperature of the three-way catalytic converter reaches the point of thermal degradation, the ECM blinks the MIL. To monitor misfires, the ECM uses both the VVT sensor and the crankshaft position sensor. The VVT sensor is used to identify any misfiring cylinders and the crankshaft position sensor is used to measure variations in the crankshaft rotation speed. Misfires are counted when the crankshaft rotation speed variations exceed predetermined thresholds. If the misfire count exceeds the threshold levels, and could cause emission control system performance deterioration, the ECM illuminates the MIL and stores a DTC.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0300 | Simultaneous misfiring of several cylinders occurs and one of the following conditions is met (2 trip detection logic):
·
A misfire occurs that may damage the three-way catalytic converter (MIL blinks when detect immediately). ·
An emission deterioration misfire occurs (MIL illuminates). |
·
Open or short in engine wire harness ·
Connector connection ·
Vacuum hose connections ·
Ignition system ·
Fuel injector assembly ·
Fuel pressure ·
Mass air flow meter sub-assembly ·
Engine coolant temperature sensor ·
Compression pressure ·
Valve timing ·
PCV valve and hose ·
PCV hose connections ·
Intake system ·
ECM |
| P0301
P0302 P0303 P0304 P0305 P0306 |
Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic):
·
A misfire occurs that may damage the three-way catalytic converter (MIL blinks when detect immediately). ·
An emission deterioration misfire occurs (MIL illuminates). |
When DTCs for misfiring cylinders are randomly stored, but DTC P0300 is not stored, it indicates that misfires have been detected in different cylinders at different times. DTC P0300 is only stored when several misfiring cylinders are detected at the same time.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Record the DTC(s) and freeze frame data.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Using the tester, switch the ECM from normal mode to check mode (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>CHECK MODE PROCEDURE).
Read the misfire counts of each cylinder, Cylinder #1 Misfire Count to Cylinder #6 Misfire Count, with the engine idling. If any misfire count is displayed, skip the following confirmation driving pattern.
Drive the vehicle so that the vehicle conditions displayed in Misfire RPM and Misfire Load of the Data List are the same as the freeze frame data. Perform this step several times.
In order to store misfire DTCs, it is necessary to operate the vehicle for the period of time shown in the table below, confirm the Misfire RPM and Misfire Load in the Data List.
| Engine speed | Duration |
|---|---|
| Idling | 8.0 minutes or more |
| 1000 | 4.5 minutes or more |
| 2000 | 2.5 minutes or more |
| 3000 | 1.5 minutes or more |
Check whether misfires have occurred by checking DTCs and freeze frame data.
Do not turn the engine switch off until the output DTC(s) and freeze frame data have been recorded. When the ECM returns to normal mode (default), the stored DTC(s), freeze frame data and other data are cleared.
Record the DTC(s), freeze frame data and misfire counts.
Turn the engine switch off and wait for at least 30 seconds.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Refer to DTC P0100 (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P0100).
Refer to Fuel Injector Circuit (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>Fuel Injector Circuit).
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
If any DTCs other than misfire DTCs are output, troubleshoot those DTCs first.
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
If the misfire does not recur when the vehicle is brought to the workshop, reproduce the conditions stored in the ECM as freeze frame data.
If the misfire still cannot be reproduced even though the conditions stored in the ECM as freeze frame data have been reproduced, one of the following factors is considered to be a possible cause of the problem:
There was insufficient fuel in the tank.
Improper fuel was used.
The spark plugs have been contaminated.
The problem requires further diagnosis.
After finishing repairs, check the misfire counts of the cylinders (Cylinder #1 Misfire Count to Cylinder #6 Misfire Count).
Be sure to confirm that no misfiring cylinder DTCs are stored again by conducting the confirmation driving pattern after finishing repairs.
For 6 cylinder engine, the ECM intentionally does not set the specific misfiring cylinder DTCs at high engine speed. If misfires occur only in high engine speed areas, only DTC P0300 is set.
In the event of DTC P0300 being present, perform the following operations:
Clear the DTCs (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
Start the engine and conduct the confirmation driving pattern.
Read the misfiring rates of each cylinder or DTC(s) using the intelligent tester.
Repair the cylinder(s) that has a high misfiring rate or is indicated by the DTC.
After finishing repairs, conduct the confirmation driving pattern again, in order to verify that DTC P0300 is not set.
When one of Short FT #1, Long FT #1, Short FT #2 or Long FT #2 in the freeze frame data is outside the range of +/-15%, the air fuel ratio may be rich (-15% or less) or lean (15% or higher).
When Coolant Temp in the freeze frame data is less than 75°C (167°F), the misfires have occurred only while warming up the engine.
An extremely imbalanced drive wheel which causes body vibration may cause misfire DTCs to be stored.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine / DTC.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P0300, P0301, P0302, P0303, P0304, P0305 and/or P0306 are output | A |
| DTC P0300, P0301, P0302, P0303, P0304, P0305 and/or P0306 and other DTCs are output | B |
If any DTCs other than P0300, P0301, P0302, P0303, P0304, P0305 and/or P0306 are output, troubleshoot those DTCs first.
A
B
Check the PCV hose connections.
PCV valve and hose are correctly connected and are not damaged.
OK
NG
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine / Data List / All Data / Misfire RPM and Misfire Load.
Read and note the Misfire RPM and Misfire Load values.
The Misfire RPM and Misfire Load values indicate the vehicle conditions under which the misfire occurred.
NEXT
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine / Data List / All Data / Cylinder #1 Misfire Count, Cylinder #2 Misfire Count, Cylinder #3 Misfire Count, Cylinder #4 Misfire Count, Cylinder #5 Misfire Count and Cylinder #6 Misfire Count.
Start the engine and allow the engine to idle.
Read each value for Cylinder #1 Misfire Count to Cylinder #6 Misfire Count displayed on the tester. If no misfire counts occur in any cylinders, perform procedure [A] and [B] and then check the misfire counts again.
Drive the vehicle with the Misfire RPM and Misfire Load noted in the "Read Value Using Intelligent Tester (Misfire RPM And Misfire Load)" procedures above [A].
Read the Cylinder #1 Misfire Count to Cylinder #6 Misfire Count or DTCs displayed on the tester [B].
| Result | Proceed to |
|---|---|
| Most misfires occur in only 1 or 2 cylinders | A |
| 3 cylinders or more have equal misfire counts | B |
If it is difficult to reproduce misfires for each cylinder, check the Data List item called Misfire Margin. Try to find vehicle driving conditions that lower the Misfire Margin value. Values above 30% are considered normal.
If the freeze frame data record of the engine coolant temperature is less than 75°C (167°F), the misfire may be detected only when the engine is cold.
If the freeze frame data record of the Engine Run Time is below 120 seconds, the misfire may be detected immediately after the engine is started.
A
B
Inspect the spark plug of the misfiring cylinder (See page Engine / Hybrid System>2GR-FE IGNITION>IGNITION COIL AND SPARK PLUG>ON-VEHICLE INSPECTION).
OK
NG
Perform a spark test.
If the result of the spark test is normal, proceed to the next step.
NEXT
Measure the cylinder compression pressure of the misfiring cylinder (See page Engine / Hybrid System>2GR-FE ENGINE MECHANICAL>ENGINE>ON-VEHICLE INSPECTION).
OK
NG
Disconnect the ECM connector.
Turn the engine switch on (IG).
Measure the voltage between the terminals.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D1-45 (#10) - D1-22 (E01) | Engine switch on (IG) | 11 to 14 V |
| D1-85 (#20) - D1-22 (E01) | Engine switch on (IG) | 11 to 14 V |
| D1-44 (#30) - D1-22 (E01) | Engine switch on (IG) | 11 to 14 V |
| D1-84 (#40) - D1-22 (E01) | Engine switch on (IG) | 11 to 14 V |
| D1-43 (#50) - D1-22 (E01) | Engine switch on (IG) | 11 to 14 V |
| D1-83 (#60) - D1-22 (E01) | Engine switch on (IG) | 11 to 14 V |
OK
NG
Check the fuel injector assembly injection (whether fuel volume is high or low, and whether injection pattern is poor) (See page Engine / Hybrid System>2GR-FE FUEL>FUEL INJECTOR>INSPECTION).
OK
NG
Check the intake system for vacuum leaks.
No leaks from intake system.
OK
NG
Check the fuel pressure (See page Engine / Hybrid System>2GR-FE FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION).
OK
NG
OK
NG
OK
NG
OK
NG
Check the intake system for vacuum leaks.
No leaks from intake system.
OK
NG
Check the fuel pressure (See page Engine / Hybrid System>2GR-FE FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION).
OK
NG
OK
NG
OK
NG
OK
NG
Inspect the spark plug of the misfiring cylinder (See page Engine / Hybrid System>2GR-FE IGNITION>IGNITION COIL AND SPARK PLUG>ON-VEHICLE INSPECTION).
OK
NG
Perform a spark test.
If the result of the spark test is normal, proceed to the next step.
NEXT
Measure the cylinder compression pressure of the misfiring cylinder (See page Engine / Hybrid System>2GR-FE ENGINE MECHANICAL>ENGINE>ON-VEHICLE INSPECTION).
OK
NG
Disconnect the ECM connector.
Turn the engine switch on (IG).
Measure the voltage between the terminals.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D1-45 (#10) - D1-22 (E01) | Engine switch on (IG) | 11 to 14 V |
| D1-85 (#20) - D1-22 (E01) | Engine switch on (IG) | 11 to 14 V |
| D1-44 (#30) - D1-22 (E01) | Engine switch on (IG) | 11 to 14 V |
| D1-84 (#40) - D1-22 (E01) | Engine switch on (IG) | 11 to 14 V |
| D1-43 (#50) - D1-22 (E01) | Engine switch on (IG) | 11 to 14 V |
| D1-83 (#60) - D1-22 (E01) | Engine switch on (IG) | 11 to 14 V |
OK
NG
Check the fuel injector assembly injection (whether fuel volume is high or low, and whether injection pattern is poor) (See page Engine / Hybrid System>2GR-FE FUEL>FUEL INJECTOR>INSPECTION).
OK
NG
Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter sub-assembly and ECM (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).
Repair any problems.
NEXT
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Clear the DTCs (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
Turn the engine switch off and wait for at least 30 seconds.
Start the engine and warm it up.
Turn the tester on.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P0300, P0301, P0302, P0303, P0304, P0305 or P0306.
Check the DTC judgment result.
| Result | Proceed to |
|---|---|
| ABNORMAL
(DTC P0300, P0301, P0302, P0303, P0304, P0305 and/or P0306 is output) |
A |
| NORMAL
(DTC is not output) |
B |
A
B
OK
NG
Replace the mass air flow meter sub-assembly (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>MASS AIR FLOW METER>REMOVAL).
If the results of the inspections performed in steps 13 and 18 indicated no problem, proceed to the next step without replacing the mass air flow meter sub-assembly.
NEXT
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Clear the DTCs (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
Turn the engine switch off and wait for at least 30 seconds.
Start the engine and warm it up.
Turn the tester on.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P0300, P0301, P0302, P0303, P0304, P0305 or P0306.
Check the DTC judgment result.
| Result | Proceed to |
|---|---|
| NORMAL
(DTC is not output) |
A |
| ABNORMAL
(DTC P0300, P0301, P0302, P0303, P0304, P0305 and/or P0306 is output) |
B |
A
B
Check the fuel lines for leaks or blockage.
OK
NG