Home › Engine / Hybrid System › 2AZ-FE ENGINE MECHANICAL › CYLINDER HEAD › from 2016.05
RM24M0E _51 Engine / Hybrid System _059548 2AZ-FE ENGINE MECHANICAL _0291834 CYLINDER HEAD A

2AZ-FE ENGINE MECHANICAL  CYLINDER HEAD  INSTALLATION  


CAUTION / NOTICE / HINT

PROCEDURE

Hide 11115 1.INSTALL CYLINDER HEAD GASKET

a.
U188310E01
0.221,0.111 0.729,0.290 0.508,0.179 10 Lot No.

Place a new gasket on the cylinder block surface with the Lot No. stamp facing upward.

NOTICE:
·

Remove any oil from the contact surfaces.


·

Be careful of the installation direction.




Hide 11101 2.INSTALL CYLINDER HEAD SUB-ASSEMBLY

a.

Place the cylinder head on the head gasket.

NOTICE:

Place the cylinder head gently in order to avoid damaging the gasket.



b.

Install the cylinder head bolts.

NOTICE:

The cylinder head bolts are tightened in 2 successive steps.


i.
F050595E14
1.594,0.073 1.74,0.229 0.146,0.156 10 false 1 2.188,1.906 2.333,2.063 0.146,0.156 10 false 5 2.823,0.073 2.969,0.229 0.146,0.156 10 false 9 2.833,1.906 2.979,2.063 0.146,0.156 10 false 7 2.198,0.073 2.344,0.229 0.146,0.156 10 false 3 0.99,1.906 1.135,2.063 0.146,0.156 10 false 4 1,0.073 1.146,0.229 0.146,0.156 10 false 6 0.333,1.906 0.542,2.063 0.208,0.156 10 false 10 0.375,0.073 0.521,0.229 0.146,0.156 10 false 8 1.604,1.906 1.75,2.063 0.146,0.156 10 false 2

Apply a light coat of engine oil to the threads and under the heads of the cylinder head set bolts.


ii.

Using several steps, uniformly install and tighten the 10 cylinder head set bolts and plate washers with a 10 mm bi-hexagon wrench in the order shown in the illustration.

Torque:
78.5 N*m (800 kgf*cm, 58 ft.*lbf)



c.
A098364E12
1.979,1.104 1.583,1.719 false 0.094,0.5 0.979,0.698 0.885,0.198 10 false Engine Front 1.396,0.24 1.667,0.427 0.271,0.188 10 false 90° 1.219,1.74 1.948,1.927 0.729,0.188 10 false Paint Mark

Mark the front of the cylinder head bolts with paint.


d.

Further tighten the cylinder head bolts by 90° as shown in the illustration.


e.

Check that the paint mark is now at a 90° angle to the front.


Hide 13050 3.INSTALL CAMSHAFT TIMING GEAR ASSEMBLY

a.

Put the camshaft timing gear and camshaft together with the straight pin and key groove misaligned, as shown in the illustration.


b.
A098365E03
1.938,0.208 1.302,0.802 false 0.979,0.948 0.854,1.823 false 1.99,0.125 2.781,0.292 0.792,0.167 10 false Straight Pin 0.406,1.833 1.188,2.115 0.781,0.281 10 true Key Groove

Turn the camshaft timing gear as shown in the illustration while pushing it gently against the camshaft. Push further at the position where the pin fits into the groove.

NOTICE:

Be sure not to turn the camshaft timing gear to the retard angle side (the right angle).



c.

Check that there is no clearance between the gear fringe and camshaft.


d.

Tighten the flange bolt with the camshaft timing gear fixed in place.

Torque:
54 N*m (551 kgf*cm, 40 ft.*lbf)


e.

Check that the camshaft timing gear can move to the retard angle side (the right direction) and is locked in the most retarded position.


Hide 13523 4.INSTALL NO. 2 CAMSHAFT TIMING SPROCKET

a.
A032167

Clamp the camshaft in a vise, then install the camshaft timing sprocket with the bolt.

Torque:
54 N*m (551 kgf*cm, 40 ft.*lbf)

NOTICE:

Do not damage the camshaft.



Hide 13511 5.INSTALL CAMSHAFT

a.

Apply a light coat of engine oil to the journal portion of the camshaft.


b.
F050592E02
1.365,0.021 2.625,0.313 1.26,0.292 10 true No. 1 Cam Lobe

Place the 2 camshafts on the cylinder head with the No. 1 cam lobes facing the directions shown in the illustration.


c.
F050591

Examine the front marks and numbers, and check that the order is as shown in the illustration. Then install the bearing caps onto the cylinder head.


d.

Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts.


e.
F050596E09
0.635,0.583 0.25,0.208 false 0.635,1.583 0.479,1.948 false 0.042,0.021 0.406,0.188 0.365,0.167 10 false No. 1 0.26,1.948 0.625,2.115 0.365,0.167 10 false No. 2 1.49,0.042 1.604,0.219 0.115,0.177 10 false 1 1.771,0.208 1.885,0.385 0.115,0.177 10 false 2 0.906,0.042 1.021,0.219 0.115,0.177 10 false 9 1.146,0.208 1.333,0.385 0.188,0.177 10 false 10 2.073,0.042 2.188,0.219 0.115,0.177 10 false 5 1.802,1.813 1.917,1.99 0.115,0.177 10 false 3 1.479,1.906 1.594,2.083 0.115,0.177 10 false 4 1.229,1.813 1.427,1.99 0.198,0.177 10 false 11 0.844,1.906 1.021,2.083 0.177,0.177 10 false 12 2.354,0.208 2.479,0.396 0.125,0.188 10 false 6 2.583,0.042 2.781,0.229 0.198,0.188 10 false 13 2.875,0.208 3.073,0.396 0.198,0.188 10 false 14 2.885,1.813 3.083,2 0.198,0.188 10 false 15 2.604,1.927 2.802,2.115 0.198,0.188 10 false 16 2.375,1.813 2.5,1.979 0.125,0.167 10 false 7 2.073,1.906 2.188,2.073 0.115,0.167 10 false 8 0.083,1.458 0.281,1.646 0.198,0.188 10 false 20 0.083,1.115 0.281,1.302 0.198,0.188 10 false 19 0.083,0.865 0.281,1.052 0.198,0.188 10 false 18 0.083,0.531 0.281,0.719 0.198,0.188 10 false 17

Using several steps, uniformly tighten the 20 bearing cap bolts in the sequence shown in the illustration.

Torque:
No. 1 and No. 2 bearing cap : 29.5 N*m (301 kgf*cm, 22 ft.*lbf)
No. 3 bearing cap : 9.0 N*m (92 kgf*cm, 80 in.*lbf)

NOTICE:
·

Determine the thrust direction of the camshaft by checking the location of the No. 1 and No. 2 bearing caps. Then tighten the bolts.


·

Install the camshaft with the timing mark of the camshaft timing gear on top.




Hide 19315 10.INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE

Hide 11302 11.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY

Hide 13540 12.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

Hide 16620 13.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

Hide 11201 17.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 51217A 25.INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT RH

Hide 16571C 26.CONNECT NO. 1 RADIATOR HOSE

a.

Connect the hose to the cylinder head.


Hide 11452 27.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

a.

Apply a light coat of engine oil to a new O-ring and install it onto the guide.


b.
U188271E01
2.337,0.081 3.224,0.292 0.887,0.211 10 New O-ring 2.637,1.561 2.132,0.164 2.132,0.164 2.269,0.164 false

Install the guide with the bolt.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 15301 28.INSTALL ENGINE OIL LEVEL DIPSTICK

Hide 25051 29.INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

a.

Install a new gasket onto the cylinder head.


b.

Temporarily tighten the exhaust manifold converter with the 5 nuts.


c.
A112190E05
1.5,0.302 1.635,0.479 0.135,0.177 10 false 1 1.042,0 1.208,0.208 0.167,0.208 10 false 2 2.354,0 2.5,0.208 0.146,0.208 10 false 3 0.146,0.542 0.271,0.74 0.125,0.198 10 false 4 2.906,0.333 3.073,0.542 0.167,0.208 10 false 5

Tighten the 5 nuts in the sequence shown in the illustration.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


Hide 17167 30.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

a.
A112189

Install the exhaust manifold heat insulator with the 4 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 17139 31.INSTALL NO. 2 MANIFOLD STAY

a.
A112192

Install the stay with the bolt and nut.

Torque:
44 N*m (449 kgf*cm, 32 ft.*lbf)


Hide 17118 32.INSTALL MANIFOLD STAY

a.
A112193

Install the stay with the bolt and nut.

Torque:
44 N*m (449 kgf*cm, 32 ft.*lbf)


Hide 23250 37.INSTALL FUEL DELIVERY PIPE WITH INJECTOR ASSEMBLY

a.

Install the fuel delivery pipe with injector assembly (See page Engine / Hybrid System>2AZ-FE FUEL>FUEL INJECTOR>INSTALLATION).


Hide 11101J 38.INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

Hide 87245A 40.CONNECT HEATER WATER INLET HOSE

a.

Connect the heater water inlet hose.

A394015E01
0.292,0.188 0.667,0.427 0.375,0.24 12 false *A 4.031,0.135 4.406,0.375 0.375,0.24 12 false *B

Text in Illustration
*A for Automatic Transaxle
for CVT (w/ Air Cooled Transmission Oil Cooler)
*B for CVT (w/o Air Cooled Transmission Oil Cooler)


Hide 42.INSTALL COWL TOP OUTER PANEL WITH WINDSHIELD WIPER MOTOR AND LINK

a.

Install the cowl top outer panel with windshield wiper motor and link (See page Vehicle Interior>WIPER / WASHER>FRONT WIPER MOTOR>INSTALLATION).


Hide 44.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 45.INSPECT FOR FUEL LEAK

Hide 49.INSPECT FOR OIL LEAK

Hide 50.INSPECT FOR EXHAUST GAS LEAK

Hide 53701 54.INSTALL FRONT FENDER APRON RH

Hide 51441 55.INSTALL NO. 1 ENGINE UNDER COVER

Hide 56.INSTALL FRONT WHEEL RH

Hide 53292A 57.INSTALL UPPER RADIATOR SUPPORT SEAL

Hide 58.PERFORM INITIALIZATION

a.

Perform initialization (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

NOTICE:

Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.