When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.
| Replaced Parts (A) | Pipes Requiring New Replacement |
|---|---|
| Injector assembly (including shuffling the injector assemblies between the cylinders) | ·
No. 1 injection pipe sub-assembly ·
No. 2 injection pipe sub-assembly |
| Supply pump assembly | Fuel inlet pipe sub-assembly |
·
Common rail assembly ·
Cylinder block sub-assembly ·
Cylinder head sub-assembly ·
Cylinder head gasket ·
Timing chain case assembly |
·
No. 1 injection pipe sub-assembly ·
No. 2 injection pipe sub-assembly ·
Fuel inlet pipe sub-assembly |
After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.
The injector assembly is a precision instrument. Do not use the injector assembly if it is struck or dropped.
The supply pump assembly is a precision instrument. Do not use the supply pump assembly if it is struck or dropped.
The common rail assembly is a precision instrument. Do not use the common rail assembly if it is struck or dropped.
Hold the supply pump assembly itself during removal and installation. Do not hold the pre-stroke control valve or fuel pipe, etc.
Hold the common rail assembly itself during removal and installation. Do not hold the pressure discharge valve or fuel pressure sensor, etc.
Make sure foreign matter does not enter the fuel path.
16575C
1.INSTALL NO. 1 WATER HOSE CLAMP BRACKET (w/ DPF)
Install the No. 1 water hose clamp bracket with the bolt to the timing chain case assembly.
13471
2.INSTALL CRANKSHAFT PULLEY (for Automatic Transmission)
13407
3.INSTALL CRANKSHAFT DAMPER SUB-ASSEMBLY (for Manual Transmission)
13496
4.INSTALL CRANKSHAFT PULLY COVER (for Automatic Transmission)
88451B
5.INSTALL VISCOUS HEATER CRANKSHAFT PULLEY (w/ Viscous Heater)
11382C
6.INSTALL CAMSHAFT OIL SEAL RETAINER
If the camshaft oil seal retainer is dropped, replace it with a new one.
Before installing a new camshaft oil seal retainer, clean the installation surface of the No. 3 camshaft bearing cap and cylinder head sub-assembly and remove any foreign matter.
| *1 | Camshaft Oil Seal Retainer |
| *a | Depth |
Using SST and a hammer, tap in a new camshaft oil seal retainer to the No. 3 camshaft bearing cap and cylinder head sub-assembly as shown in the illustration.
0 to 0.8 mm (0 to 0.0315 in.)
29300
7.INSTALL VACUUM PUMP ASSEMBLY
Coat 2 new O-rings with engine oil, and install them to the vacuum pump assembly.
Install the vacuum pump assembly so that the coupling teeth of the vacuum pump assembly labeled A and the groove of the No. 2 camshaft labeled B can engage.
Install the vacuum pump assembly with the 3 bolts to the cylinder head sub-assembly.
25706
8.INSTALL NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY
Install the No. 1 vacuum transmitting pipe sub-assembly with the 3 bolts to the cylinder head sub-assembly.
w/ EGR Cooler:
Connect the No. 1 vacuum transmitting hose to the vacuum pump assembly.
16620
9.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY
16603
10.INSTALL NO. 1 IDLER PULLEY SUB-ASSEMBLY
16331A
11.INSTALL THERMOSTAT
16321
12.INSTALL WATER INLET
Install the water inlet with the 3 bolts to the timing chain cover sub-assembly.
16304
13.INSTALL WATER OUTLET SUB-ASSEMBLY
Install a new gasket and the water outlet sub-assembly with the 4 bolts and 2 nuts to the timing chain cover sub-assembly.
16207
14.INSTALL NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY
Install the No. 2 water by-pass pipe sub-assembly with the 2 bolts to the engine water pump assembly and water inlet.
Connect the No. 3 water by-pass hose to the water outlet sub-assembly, and slide the clamp to secure the hose.
83530
15.INSTALL ENGINE OIL PRESSURE SWITCH ASSEMBLY
15407
16.TEMPORARILY INSTALL TURBO OIL INLET PIPE SUB-ASSEMBLY
17141
17.TEMPORARILY INSTALL EXHAUST MANIFOLD WITH TURBOCHARGER SUB-ASSEMBLY
15474
18.INSTALL TURBO OIL OUTLET PIPE
17293
19.TEMPORARILY INSTALL TURBOCHARGER STAY
17141
20.TIGHTEN EXHAUST MANIFOLD WITH TURBOCHARGER SUB-ASSEMBLY
17293
21.TIGHTEN TURBOCHARGER STAY
87101
22.INSTALL NO. 1 VISCOUS HEATER BRACKET SUB-ASSEMBLY (w/ Viscous Heater)
Temporarily install the No. 1 viscous heater bracket sub-assembly with the 4 bolts to the cylinder block sub-assembly and timing chain cover sub-assembly.
Tighten the 4 bolts in the sequence shown in the illustration to install the No. 1 viscous heater bracket sub-assembly.
16284
23.CONNECT NO. 1 AND NO. 2 TURBO WATER HOSE
16268
24.INSTALL NO. 1 WATER BY-PASS PIPE
Install a new gasket and the No. 1 water by-pass pipe with the 3 bolts to the timing chain cover sub-assembly.
Make sure that the claw of the gasket faces the No. 1 water by-pass pipe.
25.INSTALL WATER BY-PASS HOSE (for Water Cooled Compressor Housing Turbocharger)
16279
26.INSTALL NO. 3 WATER BY-PASS PIPE
12261
27.INSTALL PCV HOSE (except Cold Area Specification Vehicles)
17291
28.INSTALL TURBINE OUTLET ELBOW (w/o EGR Cooler)
Set a new gasket and the turbine outlet elbow to the turbocharger sub-assembly.
Temporarily install the exhaust pipe support stay to the cylinder block sub-assembly and turbine outlet elbow with the 3 bolts.
| *1 | Exhaust Pipe Clamp |
| *2 | Turbine Outlet Elbow |
| *3 | Turbocharger Sub-assembly |
| *4 | Gasket |
Install a new exhaust pipe clamp to the turbine outlet elbow with a new nut.
Tighten the 3 bolts and install the exhaust pipe support stay to the cylinder block sub-assembly and turbine outlet elbow in the order shown in the illustration.
25051
29.INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (w/ EGR Cooler)
30.INSTALL NO. 2 EXHAUST PIPE SUPPORT STAY (w/o EGR Cooler)
Temporarily install the No. 2 exhaust pipe support stay to the cylinder block sub-assembly and turbine outlet elbow with the bolt and 2 new nuts.
Tighten the bolt and 2 nuts and install the No. 2 exhaust pipe support stay to the cylinder block sub-assembly and turbine outlet elbow in the order shown in the illustration.
31.INSTALL NO. 2 EXHAUST PIPE SUPPORT STAY (w/ EGR Cooler)
17271
32.INSTALL NO. 1 TURBO INSULATOR (w/o EGR Cooler)
Install the No. 1 turbo insulator to the exhaust manifold and turbocharger sub-assembly with the 3 bolts.
17271
33.INSTALL NO. 1 TURBO INSULATOR (w/ EGR Cooler)
17167
34.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR (w/o EGR Cooler)
Install the No. 1 exhaust manifold heat insulator to the exhaust manifold with the 3 bolts.
17167
35.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR (w/ EGR Cooler)
89467B
36.INSTALL AIR FUEL RATIO SENSOR
23295D
37.INSTALL NO. 1 INJECTOR HOLDER (w/ DPF)
16281
38.CONNECT NO. 4 WATER BY-PASS HOSE (w/ DPF)
Connect the No. 4 water by-pass hose to the No. 1 injector holder, and slide the clamp to secure the hose.
16282
39.INSTALL NO. 5 WATER BY-PASS HOSE (w/ DPF)
Attach the clamp and install the No. 5 water by-pass hose to the No. 1 water hose clamp bracket.
Connect the No. 5 water by-pass hose to the No. 1 injector holder and water outlet sub-assembly, and slide the 2 clamps to secure the hose.
12229
40.INSTALL PCV PIPE (for Cold Area Specification Vehicles)
89422P
41.INSTALL ENGINE COOLANT TEMPERATURE SENSOR
16632B
42.INSTALL NO. 2 IDLER PULLEY BRACKET (w/o Air Conditioning System)
Install the No. 2 idler pulley bracket exactly as described in the procedures below to properly secure and prevent damage to the fan and generator V belt.
Temporarily install the No. 2 idler pulley bracket with the 2 bolts to the cylinder block sub-assembly.
Temporarily install the No. 2 idler pulley bracket with the 2 bolts so that the No. 2 idler pulley bracket can be moved by hand.
| *a | No Clearance |
| *b | Push |
| *c | Front |
Push the No. 2 idler pulley bracket toward the cylinder block sub-assembly as shown in the illustration and tighten bolt A.
Make sure there is no clearance between the cylinder block sub-assembly and No. 2 idler pulley bracket as shown in the illustration.
Uniformly tighten the 2 bolts in the order shown in the illustration.
88431
43.INSTALL NO. 1 COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning System)
Install the No. 1 compressor mounting bracket exactly as described in the procedures below to properly secure and prevent damage to the fan and generator V belt.
Temporarily install the No. 1 compressor mounting bracket with the 2 bolts to the cylinder block sub-assembly.
Temporarily install the No. 1 compressor mounting bracket with the 2 bolts so that the No. 1 compressor mounting bracket can be moved by hand.
| *a | No Clearance |
| *b | Push |
| *c | Front |
Push the No. 1 compressor mounting bracket toward the cylinder block sub-assembly as shown in the illustration and tighten bolt A.
Make sure there is no clearance between the cylinder block sub-assembly and No. 1 compressor mounting bracket as shown in the illustration.
Uniformly tighten the 3 bolts in the order shown in the illustration.
88320
44.INSTALL COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System)
16025
45.INSTALL NO. 5 WATER BY-PASS PIPE SUB-ASSEMBLY
|
Bolt A |
|
Bolt B |
for Laminated EGR Pre-cooler:
Install a new gasket and the No. 5 water by-pass pipe sub-assembly with the 4 bolts to the cylinder block sub-assembly.
Install a new gasket and the No. 5 water by-pass pipe sub-assembly with the 3 bolts to the cylinder block sub-assembly.
Make sure that the claw of the gasket faces the No. 5 water by-pass pipe sub-assembly.
23780B
46.INSTALL NO. 3 NOZZLE LEAKAGE PIPE (w/o Pressurized Fuel Filter)
Install the No. 3 nozzle leakage pipe with the 2 nuts to the cylinder block sub-assembly.
23300D
47.INSTALL DIESEL FUEL FILTER ASSEMBLY (w/ Pressurized Fuel Filter)
Install the diesel fuel filter assembly with the 2 nuts to the cylinder block sub-assembly.
44781
48.INSTALL HOSE BRACKET
Install the hose bracket with the 2 bolts to the cylinder head sub-assembly.
19850
49.INSTALL GLOW PLUG ASSEMBLY
19871
50.INSTALL NO. 1 GLOW PLUG CONNECTOR
23810A
51.INSTALL COMMON RAIL ASSEMBLY
23701
52.TEMPORARILY INSTALL NO. 1 AND NO. 2 INJECTION PIPE SUB-ASSEMBLY
23670
53.TIGHTEN INJECTOR ASSEMBLY
23701
54.TIGHTEN NO. 1 AND NO. 2 INJECTION PIPE SUB-ASSEMBLY
55.INSTALL WIRING HARNESS CLAMP BRACKET
Install the 2 wiring harness clamp brackets with the 2 bolts to the cylinder head cover sub-assembly.
23760
56.INSTALL NOZZLE LEAKAGE PIPE ASSEMBLY
23811H
57.INSTALL NO. 1 FUEL PIPE (w/ DPF)
58.INSTALL WIRING HARNESS CLAMP BRACKET
17111
59.INSTALL INTAKE MANIFOLD
23770
60.INSTALL NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY
23804C
61.INSTALL FUEL INLET PIPE SUB-ASSEMBLY
23815D
62.INSTALL NO. 3 FUEL PIPE (w/ Pressurized Fuel Filter)
23804D
63.INSTALL NO. 4 FUEL PIPE (w/ Pressurized Fuel Filter)
23804D
64.INSTALL NO. 4 FUEL PIPE SUB-ASSEMBLY (w/ DPF)
23271H
65.INSTALL NO. 1 FUEL HOSE
23273H
66.INSTALL NO. 2 FUEL HOSE
23243B
67.INSTALL FUEL PUMP MOTOR WIRE
22803
68.INSTALL FUEL INJECTION PUMP COVER SUB-ASSEMBLY
17118
69.INSTALL MANIFOLD STAY
70.INSTALL WIRING HARNESS CLAMP BRACKET
23812D
71.INSTALL NO. 2 FUEL PIPE
Install the No. 2 fuel pipe with the bolt to the manifold stay.
Connect the No. 1 fuel hose to the No. 2 fuel pipe, and slide the clamp to secure the hose.
11409
72.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE
25617
73.INSTALL EGR HOLE COVER PLATE (w/o EGR System)
Using an E8 "TORX" socket wrench, install 2 new stud bolts to the exhaust manifold.
Install 2 new gaskets and the 2 EGR cooler hole plates to the intake manifold and exhaust manifold with 4 new nuts.
25624
74.INSTALL EGR VALVE ADAPTER SUB-ASSEMBLY (w/o EGR System)
Temporarily install the EGR valve adapter sub-assembly to the intake manifold with the 4 bolts.
Tighten the 4 bolts in the order shown in the illustration.
Make sure to tighten the bolts in the order.
75.INSTALL EGR VALVE ADAPTER SUB-ASSEMBLY WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY (w/ EGR System without EGR Cooler)
Temporarily install the EGR valve adapter sub-assembly with electric EGR control valve assembly to the intake manifold with the 4 bolts.
Tighten the 4 bolts in the order shown in the illustration.
Make sure to tighten the bolts in the order.
25800
76.INSTALL NO. 1 EGR COOLER AND NO. 2 EGR VALVE ASSEMBLY WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY (w/ EGR System with EGR Cooler)
16209
77.INSTALL NO. 4 WATER BY-PASS PIPE SUB-ASSEMBLY
Install the No. 4 water by-pass pipe sub-assembly with the 2 bolts to the intake manifold.
for Cold Area Specification Vehicles:
Attach the clamp and connect the No. 11 water by-pass hose to the diesel throttle body assembly.
Connect the water hose to the No. 2 EGR valve assembly, and slide the clamp to secure the hose.
Connect the No. 7 water by-pass hose to the No. 4 water by-pass pipe sub-assembly, and slide the clamp to secure the hose.
Connect the No. 6 water by-pass hose to the No. 4 water by-pass pipe sub-assembly, and slide the clamp to secure the hose.
25804
78.INSTALL VACUUM CONTROL VALVE SET (w/ EGR Cooler)
25601
79.INSTALL EGR PIPE WITH COOLER SUB-ASSEMBLY (for Laminated EGR Pre-cooler)
Using an E8 "TORX" socket wrench, install 2 new stud bolts to the exhaust manifold.
Install 2 new gaskets and the EGR pipe with cooler sub-assembly to the exhaust manifold and EGR valve adapter with 4 new nuts.
Connect the EGR pipe with cooler sub-assembly to the cylinder head sub-assembly with the bolt.
Install the water hose to the EGR pipe with cooler sub-assembly and No. 5 water by-pass pipe, and slide the 2 clamps to secure the hose.
25601
80.INSTALL NO. 1 EGR PIPE SUB-ASSEMBLY (w/ EGR System)
Using an E8 "TORX" socket wrench, install 2 new stud bolts to the exhaust manifold.
Install 2 new gaskets and the No. 1 EGR pipe with the bolt and 4 new nuts to the exhaust manifold, electric EGR control valve assembly and No. 1 vacuum transmitting pipe sub-assembly.
27148A
81.INSTALL CONNECTING WIRE
Attach the 2 clamps and install the connecting wire to the hose bracket.
Connect the connector to the common rail assembly.
16206B
82.INSTALL NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY (w/o EGR Cooler)
Install the No. 3 water by-pass pipe sub-assembly to the EGR valve adapter sub-assembly with the 2 bolts.
w/ EGR System:
Connect the No. 9 water by-pass hose to the electric EGR control valve assembly, and slide the clamp to secure the hose.
Connect the No. 8 water by-pass hose to the No. 3 water by-pass pipe sub-assembly, and slide the clamp to secure the hose.
Connect the No. 4 fuel hose to the No. 3 water by-pass pipe sub-assembly.
16206B
83.INSTALL NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY (w/ EGR Cooler)
25612
84.INSTALL NO. 2 EGR PIPE
25625
85.INSTALL EGR VALVE BRACKET
23265C
86.INSTALL GAS FILTER
89421C
87.INSTALL DIESEL TURBO PRESSURE SENSOR
12631A
88.INSTALL ENGINE COVER BRACKET
Install the engine cover bracket with the 2 bolts to the cylinder head sub-assembly and hose bracket.
17578B
89.INSTALL PIPE CLAMP (w/ DPF)
25734
90.TEMPORARILY INSTALL NO. 2 VACUUM PIPE (w/ DPF)
25733A
91.TEMPORARILY INSTALL NO. 1 VACUUM PIPE (w/ DPF)
25734
92.TIGHTEN NO. 2 VACUUM PIPE (w/ DPF)
25733A
93.TIGHTEN NO. 1 VACUUM PIPE (w/ DPF)
89425
94.INSTALL EXHAUST GAS TEMPERATURE SENSOR (w/ DPF)
89481B
95.INSTALL DIFFERENTIAL PRESSURE SENSOR (w/ DPF)
16278
96.INSTALL NO. 2 WATER BY-PASS PIPE
w/ EGR Cooler:
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EGR VALVE (w/ EGR Cooler)>INSTALLATION
w/o EGR Cooler:
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EGR VALVE (w/o EGR Cooler)>INSTALLATION
26100G
97.INSTALL DIESEL THROTTLE BODY ASSEMBLY
82121
98.INSTALL ENGINE WIRE
12632
99.INSTALL NO. 2 ENGINE COVER BRACKET