After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
This section describes the standard values for all CAN related components.
The systems (ECUs and sensors) that use CAN communication vary depending on the vehicle and optional equipment. Check which systems (ECUs and sensors) are installed to the vehicle.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>SYSTEM DIAGRAM
Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
NO. 1 GLOBAL CAN JUNCTION CONNECTOR
Check the No. 1 global CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 1 Global CAN Junction Connector) |
- | - |
Check the connection diagram of the components which are connected to the No. 1 global CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| A77-1 (CANH) | G | No. 2 skid control ECU (brake actuator assembly)
(for Bus 2) |
| A77-12 (CANL) | W | |
| A77-2 (CANH) | R | No. 1 skid control ECU (brake booster with master cylinder assembly)
(for Bus 2) |
| A77-13 (CANL) | W | |
| A77-6 (CANH) | SB | Central gateway ECU (network gateway ECU)
(for Bus 2) |
| A77-17 (CANL) | W | |
| A77-7 (CANH) | P | Vehicle approaching speaker controller*1
(for Bus 2) |
| A77-18 (CANL) | W | |
| A77-8 (CANH) | L | Hybrid vehicle control ECU
(for Bus 2) |
| A77-19 (CANL) | W | |
| A77-9 (CANH) | B | ECM
(for Bus 2) |
| A77-20 (CANL) | W | |
| A77-10 (CANH) | LG | Inverter with converter assembly*2
(for Bus 2) |
| A77-21 (CANL) | W | |
| A77-11 (CANH) | V | Inverter with converter assembly
(for Bus 2) |
| A77-22 (CANL) | W |
*1: w/ Vehicle Proximity Notification System
*2: for 4WD/AWD
NO. 2 GLOBAL CAN JUNCTION CONNECTOR
Check the No. 2 global CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 2 Global CAN Junction Connector) |
- | - |
Check the connection diagram of the components which are connected to the No. 2 global CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| H90-2 (CANH) | G | Rack and pinion power steering gear assembly
(for Bus 4) |
| H90-12 (CANL) | W | |
| H90-3 (CANH) | L | No. 1 skid control ECU (brake booster with master cylinder assembly)*1
(for Bus 4) |
| H90-13 (CANL) | W | |
| H90-3 (CANH) | L | No. 2 skid control ECU (brake actuator assembly)*2
(for Bus 4) |
| H90-13 (CANL) | W | |
| H90-4 (CANH) | P | ECM
(for Bus 4) |
| H90-14 (CANL) | W | |
| H90-5 (CANH) | BE | Hybrid vehicle control ECU
(for Bus 4) |
| H90-15 (CANL) | W | |
| H90-6 (CANH) | SB | No. 8 global CAN junction connector
(for Bus 4) |
| H90-16 (CANL) | W | |
| H90-7 (CANH) | V | Steering sensor
(for Bus 4) |
| H90-17 (CANL) | W | |
| H90-8 (CANH) | R | Airbag sensor assembly
(for Bus 4) |
| H90-18 (CANL) | W | |
| H90-9 (CANH) | P | Tire pressure warning ECU and receiver*3
(for Bus 4) |
| H90-19 (CANL) | W |
*1: for LHD
*2: for RHD
*3: w/ Tire Pressure Warning System
NO. 3 GLOBAL CAN JUNCTION CONNECTOR
Check the No. 3 global CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 3 Global CAN Junction Connector) |
- | - |
Check the connection diagram of the components which are connected to the No. 3 global CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| H91-2 (CANH) | LG | Central gateway ECU (network gateway ECU)
(for Bus 5) |
| H91-12 (CANL) | W | |
| H91-3 (CANH) | G | Certification ECU (smart key ECU assembly)
(for Bus 5) |
| H91-13 (CANL) | W | |
| H91-4 (CANH) | SB | Air conditioning amplifier assembly
(for Bus 5) |
| H91-14 (CANL) | W | |
| H91-5 (CANH) | P | Outer mirror control ECU assembly RH*1
(for Bus 5) |
| H91-15 (CANL) | W | |
| H91-6 (CANH) | B | No. 4 global CAN junction connector
(for Bus 5) |
| H91-16 (CANL) | W | |
| H91-7 (CANH) | GR | Integration control sub-assembly*2
(for Bus 5) |
| H91-17 (CANL) | W |
*1: w/ Seat Position Memory System
*2: w/ Toyota Multi Operation Touch System
NO. 4 GLOBAL CAN JUNCTION CONNECTOR
Check the No. 4 global CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 4 Global CAN Junction Connector) |
- | - |
Check the connection diagram of the components which are connected to the No. 4 global CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| H92-1 (CANH) | BE | Main body ECU (multiplex network body ECU)
(for Bus 5) |
| H92-7 (CANL) | W | |
| H92-2 (CANH) | LG | Meter mirror sub-assembly*1
(for Bus 5) |
| H92-8 (CANL) | W | |
| H92-3 (CANH) | B | No. 3 global CAN junction connector
(for Bus 5) |
| H92-9 (CANL) | W | |
| H92-4 (CANH) | R | No. 9 global CAN junction connector
(for Bus 5) |
| H92-10 (CANL) | W | |
| H92-5 (CANH) | P | Outer mirror control ECU assembly LH*2
(for Bus 5) |
| H92-11 (CANL) | W |
*1: w/ Headup Display System
*2: w/ Seat Position Memory System
NO. 5 GLOBAL CAN JUNCTION CONNECTOR
Check the No. 5 global CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 5 Global CAN Junction Connector) |
- | - |
Check the connection diagram of the components which are connected to the No. 5 global CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| H94-1 (CANH) | P | Central gateway ECU (network gateway ECU)
(for Bus 1) |
| H94-11 (CANL) | W | |
| H94-2 (CANH) | R | Millimeter wave radar sensor assembly*1
(for Bus 1) |
| H94-12 (CANL) | W | |
| H94-3 (CANH) | L | Forward recognition camera*1
(for Bus 1) |
| H94-13 (CANL) | W | |
| H94-4 (CANH) | B | No. 10 global CAN junction connector
(for Bus 1) |
| H94-14 (CANL) | W | |
| H94-5 (CANH) | L | Clearance warning ECU assembly*2
(for Bus 1) |
| H94-15 (CANL) | W | |
| H94-6 (CANH) | GR | Parking assist ECU*3
(for Bus 1) |
| H94-16 (CANL) | W |
*1: w/ Toyota Safety Sense
*2: w/ TOYOTA Parking Assist-sensor System
*3: w/ Panoramic View Monitor System
NO. 6 GLOBAL CAN JUNCTION CONNECTOR
Check the No. 6 global CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 6 Global CAN Junction Connector) |
- | - |
Check the connection diagram of the components which are connected to the No. 6 global CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| H95-2 (CANH) | B | Central gateway ECU (network gateway ECU)
(for Bus 3) |
| H95-13 (CANL) | W | |
| H95-3 (CANH) | G | Central gateway ECU (network gateway ECU)
(for Bus 3) |
| H95-14 (CANL) | W | |
| H95-4 (CANH) | B | Radio and display receiver assembly*1
(for Bus 3) |
| H95-15 (CANL) | W | |
| H95-4 (CANH) | B | Radio receiver assembly*2
(for Bus 3) |
| H95-15 (CANL) | W | |
| H95-5 (CANH) | R | Telematics transceiver*3
(for Bus 3) |
| H95-16 (CANL) | W |
*1: for 8 Inch Display
*2: for 12.3 Inch Display
*3: w/ Telematics Transceiver
NO. 8 GLOBAL CAN JUNCTION CONNECTOR
Check the No. 8 global CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 8 Global CAN Junction Connector) |
- | - |
Check the connection diagram of the components which are connected to the No. 8 global CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| M33-2 (CANH) | LG | No. 2 skid control ECU (brake actuator assembly)*1
(for Bus 4) |
| M33-8 (CANL) | W | |
| M33-2 (CANH) | LG | No. 1 skid control ECU (brake booster with master cylinder assembly)*2
(for Bus 4) |
| M33-8 (CANL) | W | |
| M33-3 (CANH) | G | Central gateway ECU (network gateway ECU)
(for Bus 4) |
| M33-9 (CANL) | W | |
| M33-4 (CANH) | SB | No. 2 global CAN junction connector
(for Bus 4) |
| M33-10 (CANL) | W | |
| M33-6 (CANH) | R | Yaw rate sensor
(for Bus 4) |
| M33-12 (CANL) | W |
*1: for LHD
*2: for RHD
NO. 9 GLOBAL CAN JUNCTION CONNECTOR
Check the No. 9 global CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 9 Global CAN Junction Connector) |
- | - |
Check the connection diagram of the components which are connected to the No. 9 global CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| M96-1 (CANH) | LG | Multiplex network door ECU*1
(for Bus 5) |
| M96-7 (CANL) | W | |
| M96-2 (CANH) | G | Position control ECU assembly LH*2
(for Bus 5) |
| M96-8 (CANL) | W | |
| M96-2 (CANH) | G | Position control ECU assembly RH*3
(for Bus 5) |
| M96-8 (CANL) | W | |
| M96-3 (CANH) | R | No. 4 global CAN junction connector
(for Bus 5) |
| M96-9 (CANL) | W | |
| M96-4 (CANH) | B | Combination meter assembly
(for Bus 5) |
| M96-10 (CANL) | W |
*1: w/ Power Back Door System
*2: for LHD with Seat Position Memory System
*3: for RHD with Seat Position Memory System
NO. 10 GLOBAL CAN JUNCTION CONNECTOR
Check the No. 10 global CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 10 Global CAN Junction Connector) |
- | - |
Check the connection diagram of the components which are connected to the No. 10 global CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| M97-3 (CANH) | V | Blind spot monitor sensor LH*1
(for Bus 1) |
| M97-9 (CANL) | W | |
| M97-4 (CANH) | B | No. 1 CAN junction terminal
(for Bus 1) |
| M97-10 (CANL) | W | |
| M97-5 (CANH) | R | Rear television camera assembly*2
(for Bus 1) |
| M97-11 (CANL) | W | |
| M97-6 (CANH) | B | No. 5 global CAN junction connector
(for Bus 1) |
| M97-12 (CANL) | W |
*1: w/ Blind Spot Monitor System
*2: w/ Panoramic View Monitor System or Parking Assist Monitor System
NO. 1 CAN JUNCTION TERMINAL
Check the No. 1 CAN junction terminal.
Connection diagram
| *a | Front view of wire harness connector
(to No. 1 CAN Junction Terminal) |
- | - |
Check the connection diagram of the components which are connected to the No. 1 CAN junction terminal.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| M89-3 (CANH) | B | No. 10 global CAN junction connector
(for Bus 1) |
| M89-2 (CANL) | W |
DLC3
Disconnect the cable from the negative (-) auxiliary battery terminal.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H56-6 (CANH) - H56-14 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| H56-6 (CANH) - H56-4 (CG) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H56-14 (CANL) - H56-4 (CG) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H56-6 (CANH) - H56-16 (BAT) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H56-14 (CANL) - H56-16 (BAT) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)
| *a | Component without harness connected
(Central Gateway ECU (Network Gateway ECU)) |
- | - |
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H59 central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to Central Gateway ECU (Network Gateway ECU)) |
- | - |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H59-14 (CA6H) - H59-5 (CA6L) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 1 MΩ or higher |
| H59-14 (CA6H) - H59-10 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H59-5 (CA6L) - H59-10 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H59-14 (CA6H) - H59-1 (BATT) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H59-5 (CA6L) - H59-1 (BATT) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H59-23 (CA1H) - H59-8 (CA1L) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| H59-23 (CA1H) - H59-10 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H59-8 (CA1L) - H59-10 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H59-23 (CA1H) - H59-1 (BATT) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H59-8 (CA1L) - H59-1 (BATT) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H59-18 (CA4H) - H59-17 (CA4L) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| H59-18 (CA4H) - H59-10 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H59-17 (CA4L) - H59-10 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H59-18 (CA4H) - H59-1 (BATT) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H59-17 (CA4L) - H59-1 (BATT) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H59-6 (CA3H) - H59-19 (CAYH) | HIGH-level CAN bus line - HIGH-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | Below 1 Ω |
| H59-21 (CA3L) - H59-20 (CAYL) | LOW-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | Below 1 Ω |
| H59-6 (CA3H) - H59-10 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H59-21 (CA3L) - H59-10 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H59-6 (CA3H) - H59-1 (BATT) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H59-21 (CA3L) - H59-1 (BATT) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H59-22 (CA2H) - H59-7 (CA2L) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| H59-22 (CA2H) - H59-10 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H59-7 (CA2L) - H59-10 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H59-22 (CA2H) - H59-1 (BATT) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H59-7 (CA2L) - H59-1 (BATT) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H59-15 (CA5H) - H59-16 (CA5L) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| H59-15 (CA5H) - H59-10 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H59-16 (CA5L) - H59-10 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H59-15 (CA5H) - H59-1 (BATT) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H59-16 (CA5L) - H59-1 (BATT) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
STEERING SENSOR
| *a | Component without harness connected
(Steering Sensor) |
- | - |
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H57 steering sensor connector.
| *a | Front view of wire harness connector
(to Steering Sensor) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H57-3 (CANH) - H57-8 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| H57-3 (CANH) - H57-6 (ESS) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H57-8 (CANL) - H57-6 (ESS) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H57-3 (CANH) - H57-4 (BAT) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H57-8 (CANL) - H57-4 (BAT) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
YAW RATE SENSOR
| *a | Component without harness connected
(Yaw Rate Sensor) |
- | - |
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the M1 yaw rate sensor assembly connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Yaw Rate Sensor) |
- | - |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| M1-3 (CANH) - M1-2 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| M1-3 (CANH) - M1-1 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| M1-2 (CANL) - M1-1 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| M1-3 (CANH) - H56-16 (BAT) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| M1-2 (CANL) - H56-16 (BAT) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
HYBRID VEHICLE CONTROL ECU
Refer to Terminals of ECU.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the A32 and H67 hybrid vehicle control ECU connectors.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to Hybrid Vehicle Control ECU) |
- | - |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| A32-21 (CA1H) - A32-8 (CA1L) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| A32-21 (CA1H) - H67-3 (E1) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A32-8 (CA1L) - H67-3 (E1) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A32-21 (CA1H) - H67-27 (BATT) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A32-8 (CA1L) - H67-27 (BATT) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| A32-7 (CA3P) - A32-20 (CA3N) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| A32-7 (CA3P) - H67-3 (E1) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A32-20 (CA3N) - H67-3 (E1) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A32-7 (CA3P) - H67-27 (BATT) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A32-20 (CA3N) - H67-27 (BATT) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
INVERTER WITH CONVERTER ASSEMBLY
Refer to Terminals of ECU.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the A55 inverter with converter assembly connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Inverter with Converter Assembly) |
- | - |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| A55-22 (CANH) - A55-31 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| A55-22 (CANH) - A55-9 (GND1) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A55-31 (CANL) - A55-9 (GND1) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A55-22 (CANH) - H56-16 (BAT) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A55-31 (CANL) - H56-16 (BAT) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| A55-24 (CNH2) - A55-33 (CNL2) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| A55-24 (CNH2) - A55-9 (GND1) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A55-33 (CNL2) - A55-9 (GND1) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A55-24 (CNH2) - H56-16 (BAT) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A55-33 (CNL2) - H56-16 (BAT) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
ECM
Refer to Terminals of ECU.
Click hereEngine / Hybrid System>A25A-FXS, A25B-FXS (ENGINE CONTROL)>SFI SYSTEM>TERMINALS OF ECM
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the A27 ECM connector.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to ECM) |
- | - |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| A27-8 (CANH) - A27-18 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| A27-8 (CANH) - A27-10 (E1) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A27-18 (CANL) - A27-10 (E1) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A27-8 (CANH) - A27-1 (BATT) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A27-18 (CANL) - A27-1 (BATT) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| A27-7 (CAN+) - A27-17 (CAN-) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| A27-7 (CAN+) - A27-10 (E1) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A27-17 (CAN-) - A27-10 (E1) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A27-7 (CAN+) - A27-1 (BATT) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A27-17 (CAN-) - A27-1 (BATT) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
COMBINATION METER ASSEMBLY
Refer to Terminals of ECU.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H21 combination meter assembly connector.
| *a | Front view of wire harness connector
(to Combination Meter Assembly) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H21-32 (CANH) - H21-31 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| H21-32 (CANH) - H21-21 (ES) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H21-31 (CANL) - H21-21 (ES) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H21-32 (CANH) - H21-40 (B) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H21-31 (CANL) - H21-40 (B) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
NO. 1 SKID CONTROL ECU (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)
Refer to Terminals of ECU.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the A44 No. 1 skid control ECU (brake booster with master cylinder assembly) connector.
| *a | Front view of wire harness connector
(to No. 1 Skid Control ECU (Brake Booster with Master Cylinder Assembly)) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| A44-35 (CA2H) - A44-36 (CA2L) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| A44-35 (CA2H) - A44-28 (GND1) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A44-36 (CA2L) - A44-28 (GND1) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A44-35 (CA2H) - A44-14 (+BI1) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A44-36 (CA2L) - A44-14 (+BI1) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| A44-38 (CA1H) - A44-39 (CA1L) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| A44-38 (CA1H) - A44-28 (GND1) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A44-39 (CA1L) - A44-28 (GND1) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A44-38 (CA1H) - A44-14 (+BI1) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A44-39 (CA1L) - A44-14 (+BI1) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
NO. 2 SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)
Refer to Terminals of ECU.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the A57 No. 2 skid control ECU (brake actuator assembly) connector.
| *a | Front view of wire harness connector
(to No. 2 Skid Control ECU (Brake Actuator Assembly)) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| A57-16 (CA2H) - A57-17 (CA2L) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| A57-16 (CA2H) - A57-1 (GND1) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A57-17 (CA2L) - A57-1 (GND1) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A57-16 (CA2H) - A57-14 (+BS) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A57-17 (CA2L) - A57-14 (+BS) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| A57-27 (CANH) - A57-43 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| A57-27 (CANH) - A57-1 (GND1) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A57-43 (CANL) - A57-1 (GND1) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A57-27 (CANH) - A57-14 (+BS) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A57-43 (CANL) - A57-14 (+BS) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
Refer to Terminals of ECU.
Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H43 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Main Body ECU (Multiplex Network Body ECU)) |
- | - |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H43-5 (CANH) - H43-4 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| H43-5 (CANH) - H56-4 (CG) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H43-4 (CANL) - H56-4 (CG) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H43-5 (CANH) - H56-16 (BAT) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H43-4 (CANL) - H56-16 (BAT) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
Refer to Terminals of ECU.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H48 certification ECU (smart key ECU assembly) connector.
| *a | Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly)) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H48-1 (CANH) - H48-2 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| H48-1 (CANH) - H48-18 (E) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H48-2 (CANL) - H48-18 (E) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H48-1 (CANH) - H48-4 (+B) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H48-2 (CANL) - H48-4 (+B) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
RACK AND PINION POWER STEERING GEAR ASSEMBLY
Refer to Terminals of ECU.
Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the C67 rack and pinion power steering gear assembly connector.
| *a | Front view of wire harness connector
(to Rack and Pinion Power Steering Gear Assembly) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| C67-10 (CANH) - C67-11 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| C67-10 (CANH) - C67-7 (PGND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| C67-11 (CANL) - C67-7 (PGND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| C67-10 (CANH) - C67-8 (PIG) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| C67-11 (CANL) - C67-8 (PIG) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
AIRBAG SENSOR ASSEMBLY
Refer to Terminals of ECU.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H58 airbag sensor assembly connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Airbag Sensor Assembly) |
- | - |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H58-26 (CANH) - H58-27 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| H58-26 (CANH) - H58-33 (E1) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H58-27 (CANL) - H58-33 (E1) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H58-26 (CANH) - H56-16 (BAT) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H58-27 (CANL) - H56-16 (BAT) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
AIR CONDITIONING AMPLIFIER ASSEMBLY
Refer to Terminals of ECU.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for HV Model)>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H62 air conditioning amplifier assembly connector.
| *a | Front view of wire harness connector
(to Air Conditioning Amplifier Assembly) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H62-2 (CANH) - H62-1 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| H62-2 (CANH) - H62-17 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H62-1 (CANL) - H62-17 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H62-2 (CANH) - H62-5 (B) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H62-1 (CANL) - H62-5 (B) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
RADIO AND DISPLAY RECEIVER ASSEMBLY (for 8 Inch Display)
Refer to Terminals of ECU.
for Navigation System
for Audio and Visual System
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H2 radio and display receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Radio and Display Receiver Assembly) |
- | - |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H2-13 (CANH) - H2-14 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| H2-13 (CANH) - H56-4 (CG) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H2-14 (CANL) - H56-4 (CG) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H2-13 (CANH) - H56-16 (BAT) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H2-14 (CANL) - H56-16 (BAT) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
RADIO RECEIVER ASSEMBLY (for 12.3 Inch Display)
Refer to Terminals of ECU.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H5 radio receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Radio Receiver Assembly) |
- | - |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H5-13 (CANH) - H5-14 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| H5-13 (CANH) - H56-4 (CG) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H5-14 (CANL) - H56-4 (CG) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H5-13 (CANH) - H56-16 (BAT) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H5-14 (CANL) - H56-16 (BAT) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
BLIND SPOT MONITOR SENSOR LH (w/ Blind Spot Monitor System)
Refer to Terminals of ECU.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the M43 blind spot monitor sensor LH connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Blind Spot Monitor Sensor LH) |
- | - |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| M43-2 (CA1P) - M43-7 (CA1N) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| M43-2 (CA1P) - M43-10 (BLGD) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| M43-7 (CA1N) - M43-10 (BLGD) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| M43-2 (CA1P) - H56-16 (BAT) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| M43-7 (CA1N) - H56-16 (BAT) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
FORWARD RECOGNITION CAMERA (w/ Toyota Safety Sense)
Refer to Terminals of ECU.
Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the R5 forward recognition camera connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Forward Recognition Camera) |
- | - |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| R5-5 (CA1P) - R5-11 (CA1N) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| R5-5 (CA1P) - R5-10 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| R5-11 (CA1N) - R5-10 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| R5-5 (CA1P) - H56-16 (BAT) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| R5-11 (CA1N) - H56-16 (BAT) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Toyota Safety Sense)
Refer to Terminals of ECU.
Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT RADAR SENSOR SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the B6 millimeter wave radar sensor assembly connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly) |
- | - |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| B6-3 (CA2H) - B6-2 (CA2L) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| B6-3 (CA2H) - B6-1 (SGND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| B6-2 (CA2L) - B6-1 (SGND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| B6-3 (CA2H) - H56-16 (BAT) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| B6-2 (CA2L) - H56-16 (BAT) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
REAR TELEVISION CAMERA ASSEMBLY (w/ Panoramic View Monitor System or Parking Assist Monitor System)
Refer to Terminals of ECU.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the W15 rear television camera assembly connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Rear Television Camera Assembly) |
- | - |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| W15-4 (CANH) - W15-1 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| W15-4 (CANH) - H56-4 (CG) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| W15-1 (CANL) - H56-4 (CG) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| W15-4 (CANH) - H56-16 (BAT) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| W15-1 (CANL) - H56-16 (BAT) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
TIRE PRESSURE WARNING ECU AND RECEIVER (w/ Tire Pressure Warning System)
Refer to Terminals of ECU.
Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the M51 tire pressure warning ECU and receiver connector.
| *a | Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| M51-9 (CANH) - M51-10 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| M51-9 (CANH) - M51-12 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| M51-10 (CANL) - M51-12 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| M51-9 (CANH) - M51-7 (+B) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| M51-10 (CANL) - M51-7 (+B) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
METER MIRROR SUB-ASSEMBLY (w/ Headup Display System)
Refer to Terminals of ECU.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>HEADUP DISPLAY SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H31 meter mirror sub-assembly connector.
| *a | Front view of wire harness connector
(to Meter Mirror Sub-assembly) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H31-12 (MPX1) - H31-13 (MPX2) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| H31-12 (MPX1) - H31-4 (ES) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H31-13 (MPX2) - H31-4 (ES) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H31-12 (MPX1) - H31-2 (B) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H31-13 (MPX2) - H31-2 (B) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
CLEARANCE WARNING ECU ASSEMBLY (w/ TOYOTA Parking Assist-sensor System)
Refer to Terminals of ECU.
w/o Parking Support Brake System
w/ Parking Support Brake System (Forward/reverse Type)
w/ Parking Support Brake System (Reverse Only Type)
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H46 clearance warning ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Clearance Warning ECU Assembly) |
- | - |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H46-17 (R1) - H46-18 (R2) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| H46-17 (R1) - H46-28 (E) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H46-18 (R2) - H46-28 (E) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H46-17 (R1) - H56-16 (BAT) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H46-18 (R2) - H56-16 (BAT) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
PARKING ASSIST ECU (w/ Panoramic View Monitor System)
Refer to Terminals of ECU.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H20 parking assist ECU connector.
| *a | Front view of wire harness connector
(to Parking Assist ECU) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H20-11 (CANH) - H20-12 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| H20-11 (CANH) - H20-4 (GND1) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H20-12 (CANL) - H20-4 (GND1) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H20-11 (CANH) - H20-1 (+B) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H20-12 (CANL) - H20-1 (+B) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
POSITION CONTROL ECU ASSEMBLY LH (for LHD with Seat Position Memory System)
Refer to Terminals of ECU.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the e23 and e25 position control ECU assembly LH connectors.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to Position Control ECU Assembly LH) |
- | - |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| e25-13 (CANP) - e25-14 (CANN) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| e25-13 (CANP) - e23-2 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| e25-14 (CANN) - e23-2 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| e25-13 (CANP) - e23-3 (+B) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| e25-14 (CANN) - e23-3 (+B) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
POSITION CONTROL ECU ASSEMBLY RH (for RHD with Seat Position Memory System)
Refer to Terminals of ECU.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the e23 and e25 position control ECU assembly RH connectors.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to Position Control ECU Assembly RH) |
- | - |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| e25-13 (CANP) - e25-14 (CANN) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| e25-13 (CANP) - e23-2 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| e25-14 (CANN) - e23-2 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| e25-13 (CANP) - e23-3 (+B) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| e25-14 (CANN) - e23-3 (+B) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
OUTER MIRROR CONTROL ECU ASSEMBLY LH (w/ Seat Position Memory System)
Refer to Terminals of ECU.
Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM (w/ Memory)>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the J23 outer mirror control ECU assembly LH connector.
| *a | Front view of wire harness connector
(to Outer Mirror Control ECU Assembly LH) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| J23-9 (CANP) - J23-8 (CANN) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| J23-9 (CANP) - J23-7 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| J23-8 (CANN) - J23-7 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| J23-9 (CANP) - J23-6 (CPUB) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| J23-8 (CANN) - J23-6 (CPUB) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
OUTER MIRROR CONTROL ECU ASSEMBLY RH (w/ Seat Position Memory System)
Refer to Terminals of ECU.
Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM (w/ Memory)>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the J7 outer mirror control ECU assembly RH connector.
| *a | Front view of wire harness connector
(to Outer Mirror Control ECU Assembly RH) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| J7-9 (CANP) - J7-8 (CANN) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| J7-9 (CANP) - J7-7 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| J7-8 (CANN) - J7-7 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| J7-9 (CANP) - J7-6 (CPUB) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| J7-8 (CANN) - J7-6 (CPUB) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
MULTIPLEX NETWORK DOOR ECU (w/ Power Back Door System)
Refer to Terminals of ECU.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the W18 multiplex network door ECU connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Multiplex Network Door ECU) |
- | - |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| W18-39 (CANP) - W18-40 (CANN) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| W18-39 (CANP) - H56-4 (CG) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| W18-40 (CANN) - H56-4 (CG) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| W18-39 (CANP) - W18-20 (ECUB) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| W18-40 (CANN) - W18-20 (ECUB) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
TELEMATICS TRANSCEIVER (w/ Telematics Transceiver)
Refer to Terminals of ECU.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H11 telematics transceiver connector.
| *a | Front view of wire harness connector
(to Telematics Transceiver) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H11-25 (CANP) - H11-26 (CANN) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| H11-25 (CANP) - H11-20 (E) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H11-26 (CANN) - H11-20 (E) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H11-25 (CANP) - H11-1 (+B) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H11-26 (CANN) - H11-1 (+B) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
VEHICLE APPROACHING SPEAKER CONTROLLER (w/ Vehicle Proximity Notification System)
Refer to Terminals of ECU.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the A50 vehicle approaching speaker controller connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Vehicle Approaching Speaker Controller) |
- | - |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| A50-3 (CANH) - A50-4 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| A50-3 (CANH) - A50-6 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A50-4 (CANL) - A50-6 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A50-3 (CANH) - H56-16 (BAT) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A50-4 (CANL) - H56-16 (BAT) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
INTEGRATION CONTROL SUB-ASSEMBLY (w/ Toyota Multi Operation Touch System)
Refer to Terminals of ECU.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H8 integration control sub-assembly connector.
| *a | Front view of wire harness connector
(to Integration control sub-assembly) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H8-32 (CANP) - H8-31 (CANN) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| H8-32 (CANP) - H8-20 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H8-31 (CANN) - H8-20 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H8-32 (CANP) - H8-1 (B) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H8-31 (CANN) - H8-1 (B) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |