Home › Suspension › FRONT SUSPENSION › FRONT STABILIZER BAR(w/ KDSS)
RM2660E _53 Suspension _052815 FRONT SUSPENSION _0255386 FRONT STABILIZER BAR(w/ KDSS) A

FRONT SUSPENSION  FRONT STABILIZER BAR(w/ KDSS)  INSTALLATION  


PROCEDURE

Hide 49189A 1.INSTALL FRONT NO. 1 SUSPENSION CONTROL BLEEDER PLUG

a.
C175261

Install the 2 suspension control bleeder plugs to the front stabilizer control cylinder.

Torque:
8.3 N*m (85 kgf*cm, 73 in.*lbf)


Hide 48876 2.INSTALL FRONT STABILIZER CONTROL CYLINDER

a.
C357801E01
0.292,0.125 0.958,0.646 0.667,0.521 10 true Nut and Washer 2.219,0.052 2.729,0.479 0.51,0.427 10 true Bolt

Install the front stabilizer control cylinder to the frame with the bolt, washer and nut.

Torque:
275 N*m (2804 kgf*cm, 203 ft.*lbf)


Hide 48890 3.CONNECT FRONT NO. 1 STABILIZER CONTROL TUBE ASSEMBLY

a.
C175173E04
0.177,0.167 0.125,0.167 false 0.125,0.156 0.125,1.323 0.125,1.323 0.281,1.323 false 0.396,0.74 0.125,0.74 false 0.792,1.688 1.125,1.688 1.125,1.688 1.125,0.99 false 1.01,1.688 1.01,1.5 false 0.229,0.083 1,0.365 0.771,0.281 10 true Union Bolt 0.219,1.604 0.781,1.896 0.563,0.292 10 true Gasket

Install 2 new gaskets and the front stabilizer control cylinder to the front stabilizer control cylinder with the 2 union bolts.

Torque:
69 N*m (704 kgf*cm, 51 ft.*lbf)


Hide 17420 4.INSTALL EXHAUST CENTER PIPE ASSEMBLY

a.

for 1GR-FE:

Install the center exhaust pipe (See page Engine / Hybrid System>1GR-FE (INTAKE / EXHAUST)>EXHAUST PIPE>INSTALLATION).


b.

for 1UR-FE:

Install the center exhaust pipe (See page Engine / Hybrid System>1UR-FE (INTAKE / EXHAUST)>EXHAUST PIPE>INSTALLATION).


c.

for 3UR-FE:

Install the center exhaust pipe (See page Engine / Hybrid System>3UR-FE (INTAKE / EXHAUST)>EXHAUST PIPE>INSTALLATION).


d.

for 1VD-FTV (w/ DPF):

Install the center exhaust pipe (See page Engine / Hybrid System>1VD-FTV (INTAKE / EXHAUST)>EXHAUST PIPE(w/ DPF)>INSTALLATION).


e.

for 1VD-FTV (w/o DPF):

Install the center exhaust pipe (See page Engine / Hybrid System>1VD-FTV (INTAKE / EXHAUST)>EXHAUST PIPE(w/o DPF)>INSTALLATION).


Hide 17430 5.INSTALL TAILPIPE ASSEMBLY

a.

b.

c.

d.

for 1VD-FTV (w/ DPF):

Install the tailpipe (See page Engine / Hybrid System>1VD-FTV (INTAKE / EXHAUST)>EXHAUST PIPE(w/ DPF)>INSTALLATION).


e.

for 1VD-FTV (w/o DPF):

Install the tailpipe (See page Engine / Hybrid System>1VD-FTV (INTAKE / EXHAUST)>EXHAUST PIPE(w/o DPF)>INSTALLATION).


Hide 488A5 6.INSTALL STABILIZER CONTROL TUBE PROTECTOR

a.

Install the tube protector with the 2 bolts.

Torque:
15 N*m (152 kgf*cm, 11 ft.*lbf)


Hide 488A0 7.TEMPORARILY INSTALL FRONT STABILIZER CONTROL ARM ASSEMBLY

a.
C175172E01
0.676,1.005 1.006,1.210 0.330,0.205 10 Bolt 2.283,1.684 2.641,1.875 0.357,0.191 10 Nut

Temporarily install the stabilizer control arm to the front stabilizer control cylinder with the nut and bolt.


Hide 8.BLEED AIR FROM SUSPENSION FLUID

a.

Bleed the air from the suspension fluid (See page Suspension>SUSPENSION CONTROL>SUSPENSION CONTROL SYSTEM (w/ KDSS)>BLEEDING).


Hide 48815 9.INSTALL FRONT NO. 1 STABILIZER BAR BUSH

a.
C173669E05
1.135,1.792 1.563,1.99 0.427,0.198 10 false Bump 1.792,1.74 2.531,1.927 0.74,0.188 10 false Front Side 2.583,0.719 3.271,0.906 0.688,0.188 10 false Outer Side

Install the 2 bushes to the outer side of the bush stoppers on the front stabilizer bar as shown in the illustration.

NOTICE:

Be sure to install the front No. 1 stabilizer bar bushes so that the bump of each bush faces the inside of the vehicle.



Hide 48811 10.TEMPORARILY INSTALL FRONT STABILIZER BAR

a.
C357802E01
0.76,0.135 1.667,0.417 0.906,0.281 10 false Front Side

Set the stabilizer bracket so that the arrow mark is facing the front side of the vehicle.


b.
C173239

Temporarily install the 2 stabilizer brackets and front stabilizer bar with the 4 bolts.


c.
C175171E03
0.229,1.281 0.573,1.49 0.344,0.208 10 false Bolt 1.75,1.854 2.042,2.063 0.292,0.208 10 false Nut

Temporarily install the front stabilizer bar to the stabilizer control arm with the bolt and nut.


Hide 48820B 11.TEMPORARILY INSTALL FRONT STABILIZER LINK ASSEMBLY RH

a.
C175802E03
0.521,0.063 0.917,0.396 0.396,0.333 10 true Nut 1.083,1.833 1.406,2.073 0.323,0.24 10 true Bolt

Temporarily install the stabilizer link with the bolt.


b.

Temporarily install the stabilizer link with the nut.


c.

Tighten the nut.

Torque:
128 N*m (1305 kgf*cm, 94 ft.*lbf)

HINT:

If the ball joint turns together with the nut, use a 6 mm hexagon wrench to hold the stud bolt.



Hide 48810 12.TEMPORARILY INSTALL FRONT STABILIZER LINK ASSEMBLY LH

a.
C177821

Temporarily install the stabilizer link to the lower arm with the bolt.


b.
C178723E04
1.479,1.25 0.865,1.375 0.865,1.375 0.865,1.583 false 0.229,1.625 1.646,1.833 1.417,0.208 10 false Stabilizer Control Arm

Temporarily install the stabilizer link to the stabilizer control arm with the bolt and nut.

HINT:

If the front stabilizer control cylinder extends and it is difficult to temporarily install the stabilizer link to the stabilizer control arm, raise the stabilizer control arm with a jack and temporarily install the stabilizer link.



Hide 48829A 13.TIGHTEN FRONT NO. 1 STABILIZER BRACKET LH

a.
C177819E03
2.51,1.188 2.917,1.417 0.406,0.229 10 true 1, 3 0.969,1.417 1.198,1.615 0.229,0.198 10 true 2

Tighten the 2 bolts of the front stabilizer brackets.

Torque:
87 N*m (887 kgf*cm, 64 ft.*lbf)

NOTICE:

Tighten the bolts in 3 steps, in the order shown in the illustration.



Hide 48824A 14.TIGHTEN FRONT NO. 1 STABILIZER BRACKET RH

a.
C177820E04
0.979,1.26 1.354,1.49 0.375,0.229 10 true 1, 3 2.604,1.26 2.844,1.479 0.24,0.219 10 true 2

Tighten the 2 bolts of the front stabilizer brackets.

Torque:
87 N*m (887 kgf*cm, 64 ft.*lbf)

NOTICE:

Tighten the bolts in 3 steps, in the order shown in the illustration.



Hide 51405A 15.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 53806 16.INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

Hide 53805 17.INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

Hide 48810 19.TIGHTEN FRONT STABILIZER LINK ASSEMBLY LH

NOTICE:

Perform this procedure with all 4 wheels on the ground.


a.
C178877E04
0.865,1.74 1.25,1.948 0.385,0.208 10 false Bolt 2.469,0.302 2.896,0.708 0.427,0.406 10 true Nut

Tighten the bolt.

Torque:
135 N*m (1377 kgf*cm, 100 ft.*lbf)


b.

Tighten the nut.

Torque:
140 N*m (1428 kgf*cm, 103 ft.*lbf)


Hide 48820B 20.TIGHTEN FRONT STABILIZER LINK ASSEMBLY RH

a.
C174419E01
2.266,1.386 2.606,1.561 0.340,0.174 10 Bolt

Tighten the bolt.

Torque:
135 N*m (1376 kgf*cm, 100 ft.*lbf)

NOTICE:

Perform this procedure with all 4 wheels on the ground.



Hide 488A0 21.TIGHTEN FRONT STABILIZER CONTROL ARM ASSEMBLY

a.
C175172

Tighten the nut.

Torque:
190 N*m (1937 kgf*cm, 140 ft.*lbf)

NOTICE:

Perform this procedure with all 4 wheels on the ground.



Hide 48811 22.TIGHTEN FRONT STABILIZER BAR

a.
C175171

Tighten the nut.

Torque:
230 N*m (2345 kgf*cm, 170 ft.*lbf)

NOTICE:

Perform this procedure with all 4 wheels on the ground.



Hide 53785B 23.INSTALL FRONT FENDER APRON TRIM PACKING D

Hide 53783 24.INSTALL FRONT FENDER APRON TRIM PACKING B

Hide 48860D 27.CLOSE STABILIZER CONTROL WITH ACCUMULATOR HOUSING SHUTTER VALVE

Hide 48826D 28.INSTALL STABILIZER CONTROL VALVE PROTECTOR