MALFUNCTION DESCRIPTION
This DTC indicates that a large current flowed in the boost converter. The cause of this malfunction may be one of the following:
| Area | Main Malfunction Description |
|---|---|
| Inverter low-voltage circuit | The connectors are not connected properly |
| Resolver | Open or short circuit in the drive motor resolver or FC air compressor motor resolver circuit |
| Drive motor, FC air compressor motor | ·
Open or short circuit in the drive motor or FC air compressor motor coils ·
An internal drive motor or FC air compressor motor malfunction (iron particles or damage from foreign objects) |
| FC converter assembly low-voltage circuit | The connectors are not connected properly |
| FC converter assembly high-voltage line circuit | High-voltage line circuit malfunction (From FC converter assembly to inverter with converter assembly) |
For a description of the boost converter.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0CA300
Refer to high voltage system diagram for the System Description.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>SYSTEM DESCRIPTION
If a malfunction occurs in the boost converter, the MG ECU detects it and transmits this information to the EV control ECU.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | DTC Output from | Priority |
|---|---|---|---|---|---|---|
| P1AA900 | DC/DC Converter "A" Overcurrent (System Performance) | Boost converter fail signal detected (overcurrent due to system malfunction)*
A malfunction is detected in any of the boost converter components (inverter, FCV with motor transaxle assembly, MG ECU, etc.). (1 trip detection logic) |
·
Wire harness or connector ·
FCV with motor transaxle assembly ·
FC air compressor with motor assembly ·
Inverter with converter assembly ·
IGCT NO.4 fuse ·
FC converter assembly ·
FC junction cable ·
EV control ECU |
Master Warning:
Comes on |
EV | A |
*: This DTC is output when a large current flows in the boost converter and there is no history information indicating the specific part.
Check related parts (inverter, FC converter assembly, resolver, cable, wire harness, EV control ECU).
After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY
While referring to the vehicle conditions stored in the freeze frame data, drive the vehicle in an urban area for approximately 10 minutes.
Enter the following menus: Powertrain / EV / Utility / All Readiness.
Check the DTC judgment result.
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE, perform driving pattern again.
Refer to the wiring diagram for DTC P1E8649.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P1E8649
Refer to the wiring diagram for DTC P0AA649.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AA649
Refer to the wiring diagram for DTC P0A1B1F.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A1B1F
Refer to the wiring diagram for the inverter low-voltage circuit.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>Inverter Low-voltage Circuit
Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the EV battery service plug grip and FC converter power outlet cable on FC converter side.
Make sure to remove the service plug grip first.
Inspecting the high-voltage system
Disconnecting the low voltage connector of the inverter with converter assembly
Disconnecting the low voltage connector of the EV supply battery assembly
Disconnecting the low voltage connector of the FC converter assembly
Disconnecting the low voltage connector of the voltage inverter (for 1500W Type Voltage Inverter)
To prevent electric shock, make sure to remove the EV battery service plug grip and FC converter power outlet cable on FC converter side to cut off the high voltage circuit before servicing the vehicle.
After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, store them according to the following guidelines to prevent other technicians from accidentally reconnecting them while work is being performed on the high voltage systems.
The technician performing the work should put the EV battery service plug grip in their pocket and carry it with them.
Remove the FC converter power outlet cable on FC converter side with a "HIGH-VOLTAGE, DO NOT TOUCH" caution tag attached to it for other technicians.
| *a | Without waiting for 10 minutes |
After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION
Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly and the FC converter assembly.
Make sure to insulate the high-voltage connectors and terminals of the EV supply battery assembly with insulating tape after removing it.
If the EV supply battery assembly stored without insulating the connectors and terminals, electric shock or fire may result.
Since high voltage accumulates within the FC stack assembly with FC converter, never perform the work of separating the FC stack assembly with FC converter into the FC converter assembly and FC stack assembly without first performing electrical charge discharge (forced electrical charge discharge or electrical charge self-discharge), because doing so is dangerous.
Click hereEngine / Hybrid System>FC CONTROL>FC STACK>REMOVAL
Removing and installing the FC stack assembly without first discharging the electrical charge may result in an electric shock due to the high voltage circuit.
After turning the ignition switch off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
When disconnecting and reconnecting the auxiliary battery.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.
When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)
Pre-procedure1
None.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| P1AA900 only is output, or DTCs except the ones in the table below are also output. | A |
| Any of the following DTCs are also output. | B |
| Malfunction Content | Relevant DTC | |
|---|---|---|
| Insulation Malfunction | P1C7C49 | Hybrid/EV Battery Voltage System Isolation (A/C Area) Internal Electronic Failure |
| P1C7D49 | Hybrid/EV Battery Voltage System Isolation (Hybrid/EV Battery Area) Internal Electronic Failure | |
| P1C7E49 | Hybrid/EV Battery Voltage System Isolation (Transaxle Area) Internal Electronic Failure | |
| P1C7F49 | Hybrid/EV Battery Voltage System Isolation (Direct Current Area) Internal Electronic Failure | |
| P1EEC49 | Hybrid/EV Battery Voltage System Isolation (FC Air Compressor Area) Internal Electronic Failure | |
| P1EED49 | Hybrid/EV Battery Voltage System Isolation (FC Area) Internal Electronic Failure | |
| P1EEE49 | Hybrid/EV Battery Voltage System Isolation (Hydrogen Pump Area) Internal Electronic Failure | |
| P1EEF49 | Hybrid/EV Battery Voltage System Isolation (FC Coolant Pump Area) Internal Electronic Failure | |
| High Voltage Circuit Malfunction | P0AD911 | Hybrid/EV Battery Positive Contactor Circuit Short to Ground |
| P0AD915 | Hybrid/EV Battery Positive Contactor Circuit Short to Auxiliary Battery or Open | |
| P0ADD11 | Hybrid/EV Battery Negative Contactor Circuit Short to Ground | |
| P0ADD15 | Hybrid/EV Battery Negative Contactor Circuit Short to Auxiliary Battery or Open | |
| P1C8449 | High Voltage Power Resource Circuit Voltage Sensor after Boosting Malfunction | |
P1AA900 may be output as a result of the malfunction indicated by the DTCs above.
The chart above is listed in inspection order of priority.
Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)
Post-procedure1
Turn the ignition switch off.
A
B
Pre-procedure1
None.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| "DTC is not output" or "DTCs other than those listed below are output" | A |
| Outputs the following DTCs simultaneously
(includes pending DTCs) |
B |
| Malfunction Content | Relevant DTC | |
|---|---|---|
| Power source circuit malfunction | P1F651C | FC Converter Control Module Power Supply (-5V) Circuit Voltage Out of Range |
| P1F661C | FC Converter Control Module Power Supply (+V5AREF) Circuit Voltage Out of Range | |
| Sensor and actuator circuit malfunction | P1D0618 | FC Converter Phase U Current Circuit Current Below Threshold |
| P1D0619 | FC Converter Phase U Current Circuit Current Above Threshold | |
| P1D0718 | FC Converter Phase V Current Circuit Current Below Threshold | |
| P1D0719 | FC Converter Phase V Current Circuit Current Above Threshold | |
| P1D0818 | FC Converter Phase W Current Circuit Current Below Threshold | |
| P1D0819 | FC Converter Phase W Current Circuit Current Above Threshold | |
| P1D0918 | FC Converter Phase X Current Circuit Current Below Threshold | |
| P1D0919 | FC Converter Phase X Current Circuit Current Above Threshold | |
| P1D3011 | Phase U Reactor Current Sensor Circuit Short to Ground | |
| P1D3015 | Phase U Reactor Current Sensor Circuit Short to Battery or Open | |
| P1D301C | Phase U Reactor Current Sensor Circuit Voltage Out of Range | |
| P1D3028 | Phase U Reactor Current Sensor Signal Bias Level Out of Range / Zero Adjustment Failure | |
| P1D3511 | Phase V Reactor Current Sensor Circuit Short to Ground | |
| P1D3515 | Phase V Reactor Current Sensor Circuit Short to Battery or Open | |
| P1D351C | Phase V Reactor Current Sensor Circuit Voltage Out of Range | |
| P1D3528 | Phase V Reactor Current Sensor Signal Bias Level Out of Range / Zero Adjustment Failure | |
| P1D3A11 | Phase W Reactor Current Sensor Circuit Short to Ground | |
| P1D3A15 | Phase W Reactor Current Sensor Circuit Short to Battery or Open | |
| P1D3A1C | Phase W Reactor Current Sensor Circuit Voltage Out of Range | |
| P1D3A28 | Phase W Reactor Current Sensor Signal Bias Level Out of Range / Zero Adjustment Failure | |
| P1D4011 | Phase X Reactor Current Sensor Circuit Short to Ground | |
| P1D4015 | Phase X Reactor Current Sensor Circuit Short to Battery or Open | |
| P1D401C | Phase X Reactor Current Sensor Circuit Voltage Out of Range | |
| P1D4028 | Phase X Reactor Current Sensor Signal Bias Level Out of Range / Zero Adjustment Failure | |
| P1D4512 | Phase U Temperature Sensor Circuit Short to Battery | |
| P1D4514 | Phase U Temperature Sensor Circuit Short to Ground or Open | |
| P1D4A12 | Phase V Temperature Sensor Circuit Short to Battery | |
| P1D4A14 | Phase V Temperature Sensor Circuit Short to Ground or Open | |
| P1D4F62 | Total Reactor Current/FC Current Signal Compare Failure | |
| P1D5012 | Phase W Temperature Sensor Circuit Short to Battery | |
| P1D5014 | Phase W Temperature Sensor Circuit Short to Ground or Open | |
| P1D5512 | Phase X Temperature Sensor Circuit Short to Battery | |
| P1D5514 | Phase X Temperature Sensor Circuit Short to Ground or Open | |
| System malfunction | P1DDA00 | FC Converter Phase U Performance |
| P1DDA4B | FC Converter Phase U Over Temperature | |
| P1DDA9E | FC Converter Phase U Fail Signal Stuck On | |
| P1DDB00 | FC Converter Phase V Performance | |
| P1DDB4B | FC Converter Phase V Over Temperature | |
| P1DDB9E | FC Converter Phase V Fail Signal Stuck On | |
| P1DDC00 | FC Converter Phase W Performance | |
| P1DDC4B | FC Converter Phase W Over Temperature | |
| P1DDC9E | FC Converter Phase W Fail Signal Stuck On | |
| P1DDD00 | FC Converter Phase X Performance | |
| P1DDD4B | FC Converter Phase X Over Temperature | |
| P1DDD9E | FC Converter Phase X Fail Signal Stuck On | |
P1AA900 may be output as a result of the malfunction indicated by the DTCs above.
The chart above is listed in inspection order of priority.
Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)
Post-procedure1
Turn the ignition switch off.
A
B
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A001C
| Result | Proceed to |
|---|---|
| OK | A |
| NG (The connector is not connected securely.) | B |
| NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) | C |
A
B
C
| Proceed to |
|---|
| NEXT |
NEXT
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>Motor Resolver Circuit
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>Motor High-voltage Circuit
| Proceed to |
|---|
| NEXT |
NEXT
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>Inverter Low-voltage Circuit
| Proceed to |
|---|
| NEXT |
NEXT
Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>P1D0619
| Result | Proceed to |
|---|---|
| OK | A |
| NG (The connector is not connected securely.) | B |
| NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) | C |
A
B
C
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P1A7F00
| Result | Proceed to |
|---|---|
| OK | A |
| NG (The connector is not connected securely.) | B |
| NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) | C |
A
B
C
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P1A7F00
| Result | Proceed to |
|---|---|
| OK | A |
| NG (The connector is not connected securely.) | B |
| NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) | C |
A
B
C
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P1A7F00
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| Proceed to |
|---|
| NEXT |
NEXT
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P06881F
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Turn the ignition switch to ON (READY).
While referring to the vehicle conditions stored in the freeze frame data, drive the vehicle in an urban area for approximately 10 minutes.
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| P1AA900 is output | A |
| P1AA900 is not output | B |
Post-procedure1
Turn the ignition switch off.
A
B