Home › Engine / Hybrid System › B58 (ENGINE MECHANICAL) › TIMING GEAR CASE
RM3650E _51 Engine / Hybrid System _080179 B58 ENGINE MECHANICAL _0388907 TIMING GEAR CASE A

B58 ENGINE MECHANICAL  TIMING GEAR CASE  INSTALLATION  


PROCEDURE

Hide 1.INSTALL CRANKSHAFT POSITION SENSOR

NOTICE:
·

Electrostatic discharge.

Damage to or destruction of electrical components.

-

Leave electrical components in original packaging until just before they areinstalled. Use the original packaging only for any return shipments. Always packageremoved components straight away.

-

Only touch the housings of electrical components. Do not touch pins or multi-pinconnectors directly.

-

Anti static work clothing and antistatic shoes (with ESD symbol).

-

For additional information

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION




a.

Guide in and install crank position sensor.


b.

Tighten down 4 mm hexagon bolt.

Torque:
4.6 N*m (47 kgf*cm, 41 in.*lbf)


c.

Connect connectors and lock.

HINT:

The connector must engage audibly.



Hide 11321 2.INSTALL TIMING GEAR CASE

NOTICE:
·

Damage to the surface.

The use of metal-cutting tools (e.g. sandpaper) to clean the surfaces can damage them and lead to leaks or engine damage.

-

Do not use any metal-cutting tools.




a.
A442083

Clean sealing surfaces (1).


b.
A442084

Clean sealing surfaces (1).

NOTICE:
·

Damage to the surface.

The use of metal-cutting tools (e.g. sandpaper) to clean the surfaces can damage them and lead to leaks or engine damage.

-

Do not use any metal-cutting tools.





c.
A442086

Check the ring pins (1) for damage and replace if necessary.


d.

Check for correct fit of ring pins(1).


e.

Load the sealer gun with the seal packing.

Seal Packing:

Loctite 5970 Flange Sealant



f.
A442085

Apply the seal packing in area (1) along the inner edge.

Height of the sealing bead:

2.0 to 2.5 mm (0.0787 to 0.0984 in.)


NOTICE:
·

The application time of the liquid sealing compound can be at a maximum of 10 min.

·

Start-up of the assembly is not possible until 25 minutes after the application time.

·

Non-observance can lead to leaks in the assembly.




g.
A441463

Replace bolts (1) to (11).


h.

Carefully mount the timing gear case (A).


i.

Tighten the E8 bolts in sequence (1) to (11).

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


j.

Using SST, tighten the E10 bolts an additional 90°.

SST
09900-WA010  

HINT:
C417459C05
2.99,1.271 3.156,1.188 false 2.906,2.094 2.906,1.76 false 0.875,3 1.208,3 false 0.104,0.125 0.417,0.281 0.313,0.156 10 false *a 0.448,0.125 0.76,0.281 0.313,0.156 10 false *b 2.042,0.125 2.354,0.281 0.313,0.156 10 false *c 3.188,1.073 3.427,1.271 0.24,0.198 10 false *d 2.854,2.146 3.167,2.302 0.313,0.156 10 false *b 1.302,2.927 1.615,3.083 0.313,0.156 10 false *c
*a Example
*b Before Tightening
*c After Tightening
*d Magnetic Portion


·

The magnetic portion is used to secure the gauge to the vehicle.

·

After first adjusting the needle of the gauge to 0°, tighten to the specified angle.

·

Perform the work procedure carefully so that the gauge, etc. does not become tilted.




k.
A441343

Connect connectors (1) and lock. The connector (1) must engage audibly.


Hide 12101 4.INSTALL OIL PAN SUB-ASSEMBLY

Hide 5.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

Hide 9.SET NO. 1 CYLINDER TO TDC (COMPRESSION)

Hide 11101 10.INSTALL CYLINDER HEAD SUB-ASSEMBLY

Hide 13070A 12.INSTALL CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

Hide 135A0A 13.TEMPORARILY TIGHTEN EXHAUST CAMSHAFT TIMING GEAR BOLT ASSEMBLY

Hide 13050 14.INSTALL CAMSHAFT TIMING GEAR ASSEMBLY

Hide 135A0 15.TEMPORARILY TIGHTEN INTAKE CAMSHAFT TIMING GEAR BOLT ASSEMBLY

Hide 13506 16.TEMPORARILY INSTALL CHAIN SUB-ASSEMBLY

Hide 135A0A 17.TIGHTEN EXHAUST CAMSHAFT TIMING GEAR BOLT ASSEMBLY

Hide 135A0 18.TIGHTEN INTAKE CAMSHAFT TIMING GEAR BOLT ASSEMBLY

Hide 13540 20.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

Hide 22.INSTALL SPARK PLUG

Hide 17293 23.INSTALL TURBOCHARGER STAY

Hide 15474 24.INSTALL OUTLET TURBO OIL PIPE

Hide 11201 26.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 15370J 27.INSTALL CAM TIMING OIL CONTROL SOLENOID ASSEMBLY

Hide 23250B 28.REPLACE FUEL INJECTOR SEAL

Hide 23250 29.INSTALL FUEL INJECTOR ASSEMBLY (for Rear Side)

Hide 23250 30.INSTALL FUEL INJECTOR ASSEMBLY (for Front Side)

Hide 23470 31.ADJUST FUEL PUMP LIFTER ASSEMBLY

Hide 23100X 32.INSTALL FUEL (ENGINE ROOM SIDE) PUMP ASSEMBLY

Hide 23801P 33.INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY