Home › Engine / Hybrid System › 1UR-FE ENGINE MECHANICAL › ENGINE ASSEMBLY
RM27M0U _51 Engine / Hybrid System _049107 1UR-FE ENGINE MECHANICAL _0234042 ENGINE ASSEMBLY A

1UR-FE ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 4.REMOVE FRONT WIPER MOTOR AND LINK ASSEMBLY

a.

Remove the front wiper motor and link (See page Vehicle Interior>WIPER / WASHER>FRONT WIPER MOTOR>REMOVAL).


Hide 53301 8.REMOVE HOOD SUB-ASSEMBLY

a.
A302499

Using a screwdriver, release the 2 clips and remove the 2 hood supports assembly.

HINT:

Tape the screwdriver tip before use.


CAUTION:

Remove the hood support assembly while supporting the hood by hand.



b.

Remove the 4 bolts and hood.


Hide 11209 9.REMOVE V-BANK COVER SUB-ASSEMBLY

a.
A214822E02
2.281,1.052 2.313,1.271 2.313,1.271 2.438,1.271 false 2.792,0.354 2.958,0.354 2.958,0.354 2.729,0.656 false 0.948,1.406 1.198,1.406 false 0.563,0.719 0.458,0.719 0.458,0.719 0.635,1.219 false 0.604,0.625 1.313,0.844 0.708,0.219 10 false Grommet 1.229,1.323 1.5,1.531 0.271,0.208 10 false Pin 2.26,0.271 2.813,0.458 0.552,0.188 10 false Bracket 2.479,1.188 2.865,1.385 0.385,0.198 10 false Hook

Raise the front of the V-bank cover to detach the 2 pins. Then remove the 2 V-bank cover hooks from the bracket, and remove the V-bank cover.


Hide 17880 10.REMOVE AIR CLEANER HOSE ASSEMBLY

a.
A214569

Disconnect the vacuum sensing hose and ventilation hose.


b.

Loosen the 2 clamps.


c.

Remove the air cleaner hose.


Hide 17700 11.REMOVE AIR CLEANER ASSEMBLY

a.
A309637E02
0.052,0.042 0.948,0.531 0.896,0.49 10 true for Type A: 0.052,2.229 0.938,2.667 0.885,0.438 10 true for Type B:

Remove the air cleaner cap.

i.

Disconnect the MAF meter connector.


ii.

Using a clip remover, detach the wire harness clamp.


iii.

for Type A:

Unfasten the 4 hook clamps and then remove the air cleaner cap.


iv.

for Type B:

Unfasten the 2 hook clamps and then remove the air cleaner cap.



b.

Remove the air cleaner element.


c.
A309638E02
0.031,0.042 0.917,0.51 0.885,0.469 10 true for Type A: 0.031,2.24 0.917,2.719 0.885,0.479 10 true for Type B:

Remove the 2 bolts and air cleaner case.


Hide 55701J 12.REMOVE COWL TOP OUTER PANEL SUB-ASSEMBLY

Hide 53736 13.REMOVE FRONT FENDER APRON SEAL RH

Hide 14.REMOVE FRONT FENDER APRON SEAL REAR RH

Hide 53737B 15.REMOVE FRONT FENDER APRON SEAL LH

Hide 53739A 16.REMOVE FRONT FENDER APRON SEAL REAR LH

Hide 16571 17.REMOVE INLET RADIATOR HOSE

Hide 16572 18.DISCONNECT OUTLET RADIATOR HOSE

Hide 53101 19.REMOVE RADIATOR GRILLE SUB-ASSEMBLY

Hide 53293C 20.REMOVE RADIATOR SIDE DEFLECTOR RH

Hide 53294C 21.REMOVE RADIATOR SIDE DEFLECTOR LH

Hide 16361A 22.REMOVE FAN AND GENERATOR V BELT

Hide 16400 24.REMOVE RADIATOR ASSEMBLY

Hide 16298 25.DISCONNECT NO. 12 WATER BY-PASS HOSE

Hide 16261L 26.DISCONNECT NO. 13 WATER BY-PASS HOSE

Hide 23801P 32.DISCONNECT NO. 1 FUEL PIPE SUB-ASSEMBLY

a.
A308865

Remove the fuel pipe clamp.


b.

Disconnect the No. 1 fuel pipe (See page Engine / Hybrid System>1UR-FE FUEL>FUEL SYSTEM>PRECAUTION).


Hide 23902 33.DISCONNECT NO. 2 FUEL TUBE SUB-ASSEMBLY

a.

Disconnect the No. 2 fuel tube (See page Engine / Hybrid System>1UR-FE FUEL>FUEL SYSTEM>PRECAUTION).


Hide 34.DISCONNECT WIRE HARNESS AND HOSE

a.
A214862

Disconnect the clamp and ECM connector.

HINT:

Refer to the following procedures to disconnect the ECM connector (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>ECM>REMOVAL).



b.
A214858

Disconnect the No. 4 water by-pass hose.


c.
A214851

Disconnect the 2 heater hoses.


d.
U151465

Disconnect the 4 connectors from the connector holder block.


e.
A214573

Remove the bolt and disconnect the clamp and ground wire.


f.

Disconnect the air pump connector and 2 clamps.


g.

Remove the nut and connector bracket.


h.

Disconnect the air injection system hose.


i.
A163790

Remove the nut and disconnect the wire from the positive (+) battery cable.


j.

Disconnect the cable from the positive (+) battery terminal.


k.

Remove the bolt and disconnect the ground wire.


l.

Disconnect the 4 air injection control driver connectors.


m.

Remove the nut and disconnect the wire and 2 clips from the engine room junction block.


n.

Disconnect the 2 connectors and 2 clips from the engine room junction block.


Hide 88320 35.DISCONNECT COOLER COMPRESSOR ASSEMBLY

Hide 44320 36.DISCONNECT VANE PUMP ASSEMBLY

Hide 37110 38.REMOVE PROPELLER SHAFT ASSEMBLY

a.

for 2WD:

Refer to the following procedures (See page Drivetrain>PROPELLER SHAFT>PROPELLER SHAFT ASSEMBLY(for 2WD)>REMOVAL).


b.

for 4WD:

Refer to the following procedures (See page Drivetrain>PROPELLER SHAFT>PROPELLER SHAFT ASSEMBLY(for 4WD)>REMOVAL).


Hide 37140 39.REMOVE FRONT PROPELLER SHAFT ASSEMBLY (for 4WD)

a.

Remove the front propeller shaft (See page Drivetrain>PROPELLER SHAFT>FRONT PROPELLER SHAFT ASSEMBLY>REMOVAL).


Hide 17410 40.REMOVE EXHAUST PIPE ASSEMBLY

a.

Remove the exhaust pipe assembly (See page Engine / Hybrid System>1UR-FE EXHAUST>EXHAUST PIPE>REMOVAL).


Hide 16268 41.DISCONNECT NO. 1 WATER BY-PASS PIPE

a.
A214575

Remove the 3 bolts and disconnect the No. 1 water by-pass pipe.


Hide 11452 42.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 25601 43.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY

Hide 17168 44.REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

Hide 17105 45.REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY LH

Hide 17167 46.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 17104 47.REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH

Hide 35000 50.REMOVE AUTOMATIC TRANSMISSION ASSEMBLY

Hide 12371 51.REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR (for 2WD)

Hide 12371 52.REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR (for 4WD)

Hide 32101 53.REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

a.
A163778E01
0.9,1.607 1.201,1.763 0.302,0.156 10 SST 0.831,1.237 1.049,1.572 1.049,1.572 1.089,1.108 false

Using SST, hold the crankshaft.

SST
09213-70011  
09330-00021  


b.
A214574

Remove the 10 bolts, rear drive plate spacer, drive plate and crankshaft angle sensor rotor.


Hide 54.REMOVE ENGINE ASSEMBLY

a.
A308809

Install 2 engine hangers with 2 bolts as shown in the illustration.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
Engine hanger 12281-38150
Bolt 90119-A0166



b.

Attach an engine sling device and hang the engine with a chain block.


c.
A214577E02
0.104,0.094 0.479,0.5 0.375,0.406 10 true RH: 0.104,2.396 0.469,2.854 0.365,0.458 10 true LH:

Remove the 4 engine mounting insulator bolts.


d.

Lift the engine out from the vehicle slowly and carefully.

NOTICE:

Make sure the engine is clear of all wiring, hoses and cables.



Hide 55.INSTALL ENGINE TO ENGINE STAND

a.

Install the engine to an engine stand with the bolts.


b.

Remove the 2 bolts and 2 engine hangers.