After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
1. DISCHARGE FUEL SYSTEM PRESSURE
2.REMOVE FRONT WHEEL RH
51441C
3.REMOVE ENGINE UNDER COVER RH (for Plastic Type)
51405A
4.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (for Metal Type)
5.DRAIN ENGINE OIL
6.DRAIN ENGINE COOLANT
7.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
8.REMOVE FRONT WIPER MOTOR AND LINK ASSEMBLY
55815E
9.REMOVE FRONT NO. 1 VENTILATOR SEAL (for LHD)
55815E
10.REMOVE FRONT NO. 1 VENTILATOR SEAL (for RHD)
55735D
11.REMOVE FRONT AIR SHUTTER SEAL RH (for LHD)
55735D
12.REMOVE FRONT AIR SHUTTER SEAL RH (for RHD)
55722C
13.REMOVE INNER COWL TOP TO COWL BRACE (for LHD)
55722C
14.REMOVE INNER COWL TOP TO COWL BRACE (for RHD)
55711
15.REMOVE OUTER COWL TOP PANEL (for LHD)
55711
16.REMOVE OUTER COWL TOP PANEL (for RHD)
17.REMOVE BATTERY
74431
18.REMOVE BATTERY TRAY
11212
19.REMOVE NO. 2 CYLINDER HEAD COVER
17881
20.REMOVE AIR CLEANER CAP SUB-ASSEMBLY WITH NO. 1 AIR CLEANER HOSE
19500D
21.REMOVE NO. 1 IGNITION COIL
16573B
22.DISCONNECT NO. 3 RADIATOR HOSE
Disconnect No. 3 radiator hose.
16711
23.DISCONNECT RESERVE TANK HOSE
Disconnect the reserve tank hose.
16502
24.REMOVE WATER FILLER SUB-ASSEMBLY
Separate No. 1 radiator hose from the cylinder head.
Remove the 2 nuts and the water filler sub-assembly.
16264
25.DISCONNECT NO. 2 WATER BY-PASS HOSE
Disconnect No. 2 water by-pass hose.
16261
26.DISCONNECT WATER BY-PASS HOSE
Disconnect the water by-pass hose.
22030
27.DISCONNECT THROTTLE WITH MOTOR BODY CONNECTOR
Separate the wire harness clamp.
Remove the nut and separate the throttle with motor body connector.
12261
28.DISCONNECT VENTILATION HOSE
Disconnect the ventilation hose.
44774
29.DISCONNECT UNION TO CONNECTOR TUBE HOSE
Disconnect the union to connector tube hose.
15301
30.REMOVE OIL LEVEL DIPSTICK SUB-ASSEMBLY
17111
31.REMOVE INTAKE MANIFOLD
Separate the 3 wire harness clamps shown in the illustration.
Remove the 3 bolts, 2 nuts and the intake manifold.
11452
32.REMOVE OIL LEVEL DIPSTICK GUIDE
Disengage the clamp and disconnect the wire harness from the oil level dipstick guide.
Remove the bolt and the oil level dipstick guide.
Remove the O-ring from the oil level dipstick guide.
23901
33.DISCONNECT FUEL TUBE SUB-ASSEMBLY
44763
34.DISCONNECT BOOSTER VACUUM TUBE
Disconnect the booster vacuum tube.
11101E
35.DISCONNECT CAMSHAFT POSITION SENSOR CONNECTOR
Disconnect the camshaft position sensor connector.
89422
36.DISCONNECT ENGINE COOLANT TEMPERATURE SENSOR CONNECTOR
Disconnect the engine coolant temperature sensor connector.
89465
37.DISCONNECT HEATED OXYGEN SENSOR CONNECTOR
Remove the bolts and separate the sensor bracket.
Disconnect the heated oxygen sensor connector.
87245A
38.DISCONNECT INLET HEATER WATER HOSE A
Disconnect inlet heater water hose A.
16268
39.SEPARATE NO. 1 WATER BY-PASS PIPE
Remove the bolt and separate No. 1 water by-pass pipe.
40.DISCONNECT WIRE HARNESS
Remove the 2 bolts and disconnect the wire harness.
17410
41.SEPARATE FRONT EXHAUST PIPE ASSEMBLY
Remove the 2 bolts and 2 compression springs and separate the front exhaust pipe assembly.
17451
42.REMOVE EXHAUST PIPE GASKET
25591
43.REMOVE MANIFOLD SUPPORT BRACKET
Remove the 3 bolts and the manifold support bracket.
27020
44.REMOVE GENERATOR ASSEMBLY
19500D
45.REMOVE NO. 1 IGNITION COIL
12261
46.DISCONNECT VENTILATION HOSE
23820
47.DISCONNECT FUEL VAPOR FEED HOSE ASSEMBLY
11201
48.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY
12305
49.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH
13407
50.REMOVE CRANKSHAFT DAMPER SUB-ASSEMBLY
15100Q
51.REMOVE CRANKSHAFT POSITION SENSOR
11101J
52.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
16173
53.REMOVE WATER PUMP PULLEY
16100
54.REMOVE ENGINE WATER PUMP ASSEMBLY
12315A
55.REMOVE TRANSVERSE ENGINE ENGINE MOUNTING BRACKET
15100
56.REMOVE OIL PUMP ASSEMBLY (for Oil Pump Type A)
15100
57.REMOVE OIL PUMP ASSEMBLY (for Oil Pump Type B)
15100C
58.REMOVE OIL PUMP SEAL
13540
59.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY
13559
60.REMOVE CHAIN TENSIONER SLIPPER
13561
61.REMOVE NO. 1 CHAIN VIBRATION DAMPER
13506
62.REMOVE CHAIN SUB-ASSEMBLY
13511
63.REMOVE CAMSHAFT
When rotating the camshaft with the timing chain removed, rotate the crankshaft counterclockwise 40° from the TDC first.
Using several steps, uniformly loosen and remove the 19 bearing cap bolts in the sequence shown in the illustration, and then remove No. 1 camshaft bearing cap and No. 2 camshaft bearing cap.
Loosen each bolt uniformly while keeping the camshaft level.
Remove the camshaft and No. 2 camshaft.
11101
64.REMOVE CYLINDER HEAD SUB-ASSEMBLY
Using several steps, uniformly loosen and remove the 10 cylinder head bolts with an 8 mm bi-hexagon wrench in the sequence shown in the illustration. Remove the 10 plate washers.
Do not drop the washers into the cylinder head.
Head warpage or cracking could result from removing the bolts in the wrong order.
11115
65.REMOVE CYLINDER HEAD GASKET
Remove the cylinder head gasket.