After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
1.DISCHARGE FUEL SYSTEM PRESSURE
2.REMOVE FRONT WHEELS
51442C
3.REMOVE ENGINE UNDER COVER LH (for Plastic Type)
51441C
4.REMOVE ENGINE UNDER COVER RH (for Plastic Type)
51405A
5.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (for Metal Type)
6.DRAIN ENGINE COOLANT
7.DRAIN AUTOMATIC TRANSAXLE FLUID (for Automatic Transaxle)
8.DRAIN MANUAL TRANSAXLE OIL (for Manual Transaxle)
9.REMOVE WINDSHIELD WIPER MOTOR AND LINK
55815E
10.REMOVE FRONT NO. 1 VENTILATOR SEAL (for LHD)
55815E
11.REMOVE FRONT NO. 1 VENTILATOR SEAL (for RHD)
55735D
12.REMOVE FRONT AIR SHUTTER SEAL RH (for LHD)
55735D
13.REMOVE FRONT AIR SHUTTER SEAL RH (for RHD)
55722C
14.REMOVE INNER COWL TOP TO COWL BRACE (for LHD)
55722C
15.REMOVE INNER COWL TOP TO COWL BRACE (for RHD)
55711
16.REMOVE OUTER COWL TOP PANEL (for LHD)
55711
17.REMOVE OUTER COWL TOP PANEL (for RHD)
28800
18.REMOVE BATTERY
Disconnect the cable from the battery terminal.
Loosen the 2 nuts and remove the battery clamp.
Remove the battery.
74431
19.REMOVE BATTERY TRAY
11212
20.REMOVE NO. 2 CYLINDER HEAD COVER
17700
21.REMOVE AIR CLEANER ASSEMBLY
Disengage the clamp and disconnect the fuel vapor feed hose assembly from the No. 1 air cleaner hose.
Loosen the 2 hose clamps and disconnect the fuel vapor feed hose assembly from the No. 1 air cleaner hose and vacuum switching valve assembly.
Disconnect the No. 2 fuel vapor feed hose from the intake manifold.
Disengage the 2 clamps and disconnect the wire harness from the air cleaner cap sub-assembly and vacuum switching valve assembly.
Disconnect the mass air flow meter connector.
Disconnect the vacuum switching valve connector.
Loosen the hose clamp and disconnect the No. 1 air cleaner hose from the throttle with motor body assembly.
Disengage the 2 clamps and remove the air cleaner cap sub-assembly with No. 1 air cleaner hose.
Remove the air cleaner element.
Disengage the clamp and disconnect the wire harness from the air cleaner case.
Remove the 2 bolts and the air cleaner case from the air cleaner bracket.
17771A
22.REMOVE AIR CLEANER BRACKET
Disengage the clamp and disconnect the wire harness from the air cleaner bracket.
Remove the 2 bolts and the air cleaner bracket.
74411
23.REMOVE BATTERY CARRIER (for LHD)
Disengage the 6 wire harness clamps and separate the wire harness from the battery carrier.
Remove the 5 bolts and the battery carrier.
74411
24.REMOVE BATTERY CARRIER (for RHD)
Disengage the 7 wire harness clamps and separate the wire harness from the battery carrier.
Remove the 5 bolts and the battery carrier.
23820
25.REMOVE FUEL VAPOR FEED HOSE ASSEMBLY
Loosen the 2 hose clamps and remove the fuel vapor feed hose assembly.
26.DISCONNECT RADIATOR RESERVOIR TANK HOSE
Disconnect the radiator reservoir tank hose from the water filler.
16573B
27.DISCONNECT NO. 3 RADIATOR HOSE
Loosen the hose clamp and disconnect No. 3 radiator hose from the water filler.
16572D
28.DISCONNECT NO. 2 RADIATOR HOSE
Loosen the hose clamp and disconnect No. 2 radiator hose from the water inlet.
23842A
29.REMOVE EFI FUEL PIPE CLAMP
Remove the EFI fuel pipe clamp.
23901
30.DISCONNECT FUEL TUBE SUB-ASSEMBLY
Pinch the retainer as illustrated, then pull the fuel tube connector out of the pipe.
| *1 | Retainer |
|
Pinch |
|
Pull |
Remove any dirt and foreign matter from the fuel tube connector before performing this work.
Do not allow any scratches or foreign matter on the parts when disconnecting, as the fuel tube connector has the O-rings that seal the pipe.
Perform this work by hand. Do not use any tools.
Do not forcibly bend, twist or turn the nylon tube.
Protect the disconnected parts by covering them with vinyl bags after disconnecting the fuel tube.
If the fuel tube connector and pipe are stuck, push and pull to release them.
32922A
31.DISCONNECT OUTLET OIL COOLER HOSE (for Automatic Transaxle)
Loosen the clip and disconnect the oil cooler outlet hose.
32921D
32.DISCONNECT INLET OIL COOLER HOSE (for Automatic Transaxle)
Loosen the clip and disconnect the oil cooler inlet hose.
44773F
33.DISCONNECT UNION TO CHECK VALVE HOSE
Loosen the hose clamp and disconnect the union to check valve hose from the booster vacuum tube.
87246A
34.DISCONNECT OUTLET HEATER WATER HOSE A
Loosen the hose clamp and disconnect outlet heater water hose A from the heater unit.
87245A
35.DISCONNECT INLET HEATER WATER HOSE A
Loosen the hose clamp and disconnect inlet heater water hose A from the heater unit.
16361A
36.REMOVE FAN AND GENERATOR V BELT
31470
37.SEPARATE CLUTCH RELEASE CYLINDER ASSEMBLY (for Manual Transaxle)
88310
38.SEPARATE COMPRESSOR WITH PULLEY ASSEMBLY (w/ Air Conditioning System)
Disconnect the connector.
Remove the 4 bolts and separate the with pulley compressor assembly.
Remove the compressor assembly together with the low and high pressure hoses, then suspend them from the body with a piece of rope.
39.DISCONNECT ENGINE WIRE
for Automatic Transaxle:
Disengage the clamp and disconnect the wire harness from the automatic transaxle.
Remove the bolt and separate the wire harness from the automatic transaxle.
Disengage the wire harness clamp and separate the wire harness.
Pull up the lever and disconnect the connector of the engine control computer.
Disengage the clamp and disconnect the wire harness.
Disconnect the 2 connectors.
Disengage the 2 claws and disconnect the wire harness from the engine room relay block.
Disconnect the 2 connectors from the battery positive terminal.
Disconnect all the wire harnesses and connectors. Make sure that no wire harness is connected between the body and engine.
58910C
40.REMOVE REAR CONSOLE BOX ASSEMBLY
57533B
41.REMOVE FRONT FLOOR CENTER BRACE (w/ Side Mudguard)
17410
42.REMOVE FRONT EXHAUST PIPE ASSEMBLY
17451
43.REMOVE EXHAUST PIPE GASKET
17451A
44.REMOVE NO. 2 EXHAUST PIPE GASKET
33820B
45.SEPARATE TRANSMISSION CONTROL CABLE ASSEMBLY (for Automatic Transaxle)
33820B
46.SEPARATE TRANSMISSION CONTROL CABLE ASSEMBLY (for Manual Transaxle)
43420
47.REMOVE FRONT DRIVE SHAFT ASSEMBLY
11361J
48.REMOVE FLYWHEEL HOUSING UNDER COVER (for Automatic Transaxle)
Remove the flywheel housing cover.
32101G
49.REMOVE TORQUE CONVERTER SETTING BOLT (for Automatic Transaxle)
Hold the crankshaft with SST.
Remove the 6 torque converter set bolts.
45259A
50.REMOVE COLUMN HOLE COVER SILENCER SHEET
45209
51.SEPARATE STEERING SLIDING YOKE SUB-ASSEMBLY
45025D
52.REMOVE NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY
53.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE
Place the wooden blocks or plate lift attachments in the positions shown in the illustration and set an engine lifter underneath the engine assembly with transaxle.
| *A | for Automatic Transaxle |
| *B | for Manual Transaxle |
|
Attachment Placement Position |
Place the wooden blocks or plate lift attachments so that the front suspension crossmember sub-assembly is level.
As the engine assembly with transaxle is very heavy, be sure to support it securely.
To prevent deformation of the oil pan, never set any attachments against the oil pan of the engine assembly.
Remove the bolt, 2 nuts and the engine mounting insulator RH.
Remove the through bolt and the nut and separate the engine mounting insulator LH.
Remove the 6 bolts, and the engine assembly with transaxle and the front suspension crossmember from the vehicle.
When removing the engine, be careful not to damage any wire harnesses of the steering shaft.
12281A
54.INSTALL NO. 1 ENGINE HANGER
Remove the bolt and the oxygen sensor wiring bracket.
Install the 2 engine hangers with the 2 bolts, as shown in the illustration.
| *1 | No. 1 Engine Hanger |
| *a | Front Side |
| *b | Rear Side |
| Part Name | Part No. |
|---|---|
| Engine hanger | 12281-21010 |
| Bolt | 91642-81025 |
51201
55.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
Using an engine sling device and a chain block, suspend the engine assembly with transaxle and front suspension crossmember.
Remove the through bolt from the engine moving control rod and remove the front suspension crossmember.
82121
56.REMOVE ENGINE WIRE
Disconnect the 2 ground bolts.
Disconnect all the wire harnesses and connectors. Make sure that no wire harnesses are connected to the engine.
19500D
57.REMOVE NO. 1 IGNITION COIL
12261
58.REMOVE VENTILATION HOSE
Loosen the 2 hose clamps and remove the ventilation hose.
16502
59.REMOVE WATER FILLER SUB-ASSEMBLY
Loosen the hose clamp and disconnect radiator hose No. 1 from the cylinder head.
Remove the 2 nuts and the water filler sub-assembly.
17111
60.REMOVE INTAKE MANIFOLD
Loosen the hose clamp and disconnect the union to connector tube hose from the booster vacuum tube.
Loosen the hose clamp and disconnect the water by-pass hose from the cylinder head.
Disconnect the water by-pass hose from the No. 1 water by-pass pipe.
Remove the 3 bolts, 2 nuts and the intake manifold.
Remove the gasket from the intake manifold.
17167
61.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
Remove the 4 bolts and the No. 1 exhaust manifold heat insulator.
25591
62.REMOVE MANIFOLD SUPPORT BRACKET
Remove the 3 bolts and the manifold support bracket.
17141
63.REMOVE EXHAUST MANIFOLD
Remove the 3 bolts, 2 nuts and the exhaust manifold.
64.FIX ENGINE ASSEMBLY
Using an engine sling device and a chain block, hold the engine assembly.
To enable removal of the engine assembly, adjust the positions of the plate lift attachments and set them in place.
Set plate lift attachments so that the engine assembly with transaxle is level.
Do not perform any procedure while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.
To prevent deformation of the oil pan, never set any attachments against the oil pan of the engine assembly.
Use a belt with a tightening mechanism or a rope to secure the engine assembly with transaxle to the engine lifter.
Do not tighten the belt with a tightening mechanism or the rope any more than is necessary.
Set the engine assembly with transaxle so that is horizontal.
11363A
65.REMOVE FLYWHEEL HOUSING SIDE COVER
28100
66.REMOVE STARTER ASSEMBLY
30500
67.REMOVE AUTOMATIC TRANSAXLE ASSEMBLY (for Automatic Transaxle)
Remove the bolt and wire harness bracket from the automatic transaxle assembly.
Remove the 7 bolts and the automatic transaxle with torque converter.
32101
68.REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for Automatic Transaxle)
Hold the crankshaft with SST.
Remove the 6 bolts, drive plate spacer FR, drive plate and ring gear sub-assembly and drive plate spacer RR.
33524F
69.REMOVE CONTROL CABLE BRACKET (for Manual Transaxle)
30300
70.REMOVE MANUAL TRANSAXLE ASSEMBLY (for Manual Transaxle)
Remove the 7 bolts and the manual transaxle assembly.
31210
71.REMOVE CLUTCH COVER ASSEMBLY (for Manual Transaxle)
31250
72.REMOVE CLUTCH DISC ASSEMBLY (for Manual Transaxle)
13405
73.REMOVE FLYWHEEL SUB-ASSEMBLY (for Manual Transaxle)
Hold the crankshaft with SST.
Remove the 6 bolts and flywheel.
87245A
74.REMOVE INLET HEATER WATER HOSE A
Disconnect heater water inlet hose A from the cylinder head.
12321B
75.REMOVE DRIVE SHAFT HEAT INSULATOR SUB-ASSEMBLY
Remove the bolt, nut and the drive shaft heat insulator.
12305
76.REMOVE ENGINE MOUNTING INSULATOR RH
Only perform this procedure when replacement of the engine mounting insulator RH is necessary.
Remove the 3 bolts and engine mounting insulator RH.
12372A
77.REMOVE ENGINE MOUNTING INSULATOR LH
Only perform this procedure when replacement of the engine mounting insulator RH is necessary.
Remove the 5 bolts and engine mounting insulator LH.