DTC P1603 Engine Stall History |
| DTC No. | DTC Detection Condition | Trouble Area |
| P1603 | After monitoring for startability problems (P1604) finishes and starting the engine, with the engine running, the engine stops (the engine speed drops to 300 rpm or less) without the ignition switch being operated. (1 trip detection logic) |
|
| Symptom | Suspected Area |
| Engine vibration occurs and engine stops | Air-fuel ratio abnormal |
| Engine stops with no engine vibration | Ignition system, injection stoppage, high load from external parts |
| Engine can be started with accelerator pedal depressed | Insufficient air volume |
| Rough idling after engine started | Air-fuel ratio abnormal, abnormal combustion |

| Vehicle State | Engine Speed | Suspected Area | Primary Parts to Inspect | Procedure | |
| Idling or decelerating | Slowly decreases and engine stalls | Ignition system abnormal | Igniter abnormal |
| 10, 38, 52 |
| Air-fuel ratio abnormal | Air suction |
| 5 to 9 | ||
| Sensor malfunction (value from sensor too lean) |
| 11 to 23 | |||
| Sensor malfunction (value from sensor too rich) | 39 to 51 | ||||
| Fuel supply problem |
| 24 to 37 | |||
| Intake air volume insufficient | Problem with air passage |
| 53 to 55 | ||
| Excessive valve overlap |
| 56 to 59 | |||
| Ignition timing incorrect | Does not operate as expected |
| 60 to 64 | ||
| Rapidly decreases and engine stalls* | Ignition and injection stops (electrical system malfunction) | Power temporarily cut |
| 65, 66 | |
| External part malfunctioning | Increase in load |
| 67 to 69 | ||
| Accelerating | - | Crankshaft position sensor or VVT sensor malfunction | Power temporarily cut |
| 1 |
| Mass air flow meter | Foreign matter adhesion |
| 70 to 73 | ||
| Ignition and injection stops (electrical system malfunction) | Power temporarily cut |
| 74, 75 | ||
| Fuel supply problem | Fuel leak, clog |
| 76 to 80 | ||
| 1.CHECK FOR ANY OTHER DTCS OUTPUT |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Read the DTCs (Click here).
| Result | Proceed to |
| Only DTC P1603 is output | A |
| DTCs other than P1603 are output | B |
|
| ||||
| A | |
| 2.CHECK FREEZE FRAME DATA |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Result | Proceed to |
| Abnormal | A |
| Normal | B |
|
| ||||
| A | |
| 3.CHECK ENGINE IMMOBILISER SYSTEM |
Connect the GTS to the DLC3.
Start the engine.
Idle the engine
Enter the following menus: Powertrain / Engine / Data List / Immobiliser Communication and Immobiliser Fuel Cut.
Check the Data List indication.
| Data List Item | Result |
| Immobiliser Communication | ON |
| Immobiliser Fuel Cut | OFF |
| Result | Proceed to |
| OK | A |
| NG (w/ Entry and Start System) | B |
| NG (w/o Entry and Start System) | C |
|
| ||||
|
| ||||
| A | |
| 4.READ FREEZE FRAME DATA |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Problem Symptom | Freeze Frame Data Item | Suspected Area | Proceed to | ||
| Closed Throttle Position SW | Engine Speed | Total of Short FT and Long FT | |||
| When idling or decelerating, engine speed slowly decreases and engine stalls | All 5 sets of freeze frame data are ON | Decreases slowly*1 | All 5 sets of freeze frame data are +15% or more*2 |
| A |
| At least 1 of the 5 sets of freeze frame data is -15% or less*3 | Sensor malfunction (value from sensor too rich) | B | |||
| All 5 sets of freeze frame data are from -15% to +15% |
| C | |||
| When idling or decelerating, engine speed rapidly decreases and engine stalls | Decreases rapidly*1 | - |
| D | |
| When accelerating or driving at constant speed, engine stalls | At least one is OFF | - | - |
| E |

|
| ||||
|
| ||||
|
| ||||
|
| ||||
| A | |
| 5.CHECK INTAKE SYSTEM |
Check for air leakage in the intake system [vacuum hose disconnection, cracks, damaged gaskets, etc.] (Click here).
|
| ||||
| OK | |
| 6.CHECK PURGE VALVE |
![]() |
Disconnect the purge hose (on the canister side) of the purge valve.
Start the engine.
Idle the engine.
Disconnect the connector of the purge valve.
Check if air flows through the purge valve.
Connect the connector of the purge valve.
Connect the purge hose of the purge valve.
|
| ||||
| OK | |
| 7.READ FREEZE FRAME DATA |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item | Result | Suspected Area | Proceed to |
| Stop Light Switch | At least 1 of the 5 sets of freeze frame data is ON | Air suction from brake booster | A |
| All 5 sets of freeze frame data are OFF | - | B |
|
| ||||
| A | |
| 8.READ VALUE USING GTS (SHORT FT) |
![]() |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Start the engine and warm it up until the engine coolant temperature stabilizes.
Idle the engine.
Using the GTS, read the value of Short FT #1 in the Data List while depressing the brake pedal.
| Result | Proceed to |
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
|
| ||||
|
| ||||
| A | |
| 9.PERFORM DRIVE TEST |
Connect the GTS to the DLC3.
Start the engine and warm it up until the engine coolant temperature stabilizes.
Idle the engine.
Using the GTS, read the value of Short FT #1 in the Data List.
| Data List | Condition | Specified Condition |
| Short FT #1 + Long FT #1 | The conditions of the vehicle are matched to those present when the problem occurs | -15 to +15% |
| Result | Proceed to |
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
|
| ||||
|
| ||||
| A | |
| 10.CHECK IGNITION SYSTEM |
Perform ignition system On-vehicle Inspection (Click here).
|
| ||||
| OK | |
| 11.READ FREEZE FRAME DATA |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item | Result | Suspected Area | Proceed to |
| Calculate Load | Below 90% of the current value of the vehicle*1 | Mass air flow meter | A |
| AFS Voltage B1S1 | 2.2 V or higher*2 |
| B |
|
| ||||
| A | |
| 12.CHECK MASS AIR FLOW METER |
Remove the mass air flow meter.
Check for foreign matter in the airflow passage of the mass airflow meter.
| Result | Proceed to |
| Visible foreign matter is not present | A |
| Visible foreign matter is present | B |
|
| ||||
| A | |
| 13.CHECK HARNESS AND CONNECTOR (ECM - MASS AIR FLOW METER) |
Disconnect the ECM.
Disconnect the mass air flow meter connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A33-22 (VG) - C16-5 (VG) | Always | Below 1 Ω |
| A33-29 (E2G) - C16-4 (E2G) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| A33-22 (VG) or C16-5 (VG) - Body ground | Always | 10 kΩ or higher |
| A33-29 (E2G) or C16-4 (E2G) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 14.PERFORM DRIVE TEST |
Connect the GTS to the DLC3.
Start the engine and warm it up until the engine coolant temperature stabilizes.
Idle the engine.
Using the GTS, read the value of Calculate Load in the Data List.
| Data List | Specified Condition |
| Calculate Load | 90 to 110% of the current value of the vehicle |
| Result | Proceed to |
| Abnormal | A |
| Normal | B |
|
| ||||
| A | ||
| ||
| 15.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR) |
![]() |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Start the engine, turn off all accessory switches and warm up the engine until the engine coolant temperature stabilizes.
Idle the engine.
Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor.
Read the output voltage from the air fuel ratio sensor when increasing and decreasing the fuel injection volume.
| GTS Display | Specified Condition |
| Control the Injection Volume for A/F Sensor (+12.5%) | Air fuel ratio sensor output voltage is below 2.0 V |
| Control the Injection Volume for A/F Sensor (-12.5%) | Air fuel ratio sensor output voltage is higher than 2.4 V |
| Result | Proceed to |
| Abnormal | A |
| Normal | B |
|
| ||||
| A | |
| 16.CHECK TERMINAL VOLTAGE (AIR FUEL RATIO SENSOR POWER SOURCE) |
![]() |
Disconnect the air fuel ratio sensor connector.
Turn ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| C14-2 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector (to Air Fuel Ratio Sensor) |
|
| ||||
| OK | |
| 17.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM) |
Disconnect the ECM.
Disconnect the air fuel ratio sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A34-18 (A1A-) - C14-4 (A1A-) | Always | Below 1 Ω |
| A34-19 (A1A+) - C14-3 (A1A+) | Always | Below 1 Ω |
| A34-5 (HA1A) - C14-2 (HA1A) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| A34-18 (A1A-) or C14-4 (A1A-) - Body ground | Always | 10 kΩ or higher |
| A34-19 (A1A+) or C14-3 (A1A+) - Body ground | Always | 10 kΩ or higher |
| A34-5 (HA1A) or C14-2 (HA1A) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 18.READ FREEZE FRAME DATA |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item | Result | Proceed to |
| Initial Engine Coolant Temp, Ambient Temp for A/C, Initial Intake Air Temp | Difference in temperature between each item is less than 10°C*1 | A |
| Difference in temperature between each item is 10°C or more*2 | B |
|
| ||||
| A | |
| 19.READ FREEZE FRAME DATA |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).

| Freeze Frame Data Item | Result | Suspected Area | Proceed to |
| Initial Engine Coolant Temp, Coolant Temp, Engine Run Time | Range A |
| A |
| Range B | Engine coolant temperature sensor | B | |
| Range C | - | C |
|
| ||||
|
| ||||
| A | |
| 20.INSPECT THERMOSTAT |
| Result | Proceed to |
| Abnormal | A |
| Normal | B |
|
| ||||
| A | ||
| ||
| 21.READ FREEZE FRAME DATA |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item | Result | Suspected Area | Proceed to |
| Coolant Temp | 120°C or higher | Engine coolant temperature sensor | A |
| Coolant Temp, Ambient Temp for A/C | Engine coolant temperature is lower than outside temperature by 15°C or more | Engine coolant temperature sensor | |
| Both freeze frame data items listed above | Values are other than above | - | B |
|
| ||||
| A | |
| 22.INSPECT ENGINE COOLANT TEMPERATURE SENSOR |
Inspect the engine coolant temperature sensor (Click here).
|
| ||||
| OK | |
| 23.CHECK HARNESS AND CONNECTOR (ECM - ENGINE COOLANT TEMPERATURE SENSOR) |
Disconnect the ECM connector.
Disconnect the engine coolant temperature sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A36-30 (THW) - C40-2 (THW) | Always | Below 1 Ω |
| A36-29 (E1) - C40-1 (E2) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| A36-30 (THW) or C40-2 (THW) - Body ground | Always | 10 kΩ or higher |
| A36-29 (E1) or C40-1 (E2) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 24.READ FREEZE FRAME DATA |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item | Result | Suspected Area | Proceed to |
| EVAP (Purge) VSV | At least 1 of the 5 sets of freeze frame data is not 0% | Purge valve | A |
| All 5 sets of freeze frame data are 0% | - | B |
|
| ||||
| A | |
| 25.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VSV FOR EVAP CONTROL) |
![]() |
Disconnect the purge hose (on the canister side) of the purge valve.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Start the engine.
Enter the following menus: Powertrain / Engine / Active Test / Activate the VSV for Evap Control.
Operate the purge valve and check the airflow.
| Activate the VSV for Evap Control | Specified Condition |
| ON | Air flows |
| OFF | Air does not flow |
| Result | Proceed to |
| NG | A |
| OK | B |
| *a | VSV ON (Air flows) |
| *b | VSV OFF (Air does not flow) |
|
| ||||
| A | |
| 26.INSPECT PURGE VALVE |
Inspect the purge valve (Click here).
|
| ||||
| OK | |
| 27.CHECK TERMINAL VOLTAGE (PURGE VALVE POWER SOURCE) |
![]() |
Disconnect the purge valve connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| d1-1 - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector (to Purge valve) |
|
| ||||
| OK | |
| 28.CHECK HARNESS AND CONNECTOR (PURGE VALVE - ECM) |
Disconnect the purge valve connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A36-11 (PRG) - d1-2 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| A36-11 (PRG) or d1-2 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 29.CLEAR DTC |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (Click here).
| NEXT | |
| 30.READ VALUE USING GTS (EVAP (Purge) VSV) |
Connect the GTS to the DLC3.
Start the engine and warm it up until the engine coolant temperature stabilizes.
Idle the engine for 15 minutes or more.
Using the GTS, read the value of EVAP (Purge) VSV in the Data List.
| Data List | Specified Condition |
| EVAP (Purge) VSV | Value other than 0% is displayed |
| Result | Proceed to |
| Abnormal | A |
| Normal | B |
|
| ||||
| A | |
| 31.PERFORM ACTIVE TEST USING GTS |
![]() |
Disconnect the purge hose (on the canister side) of the purge valve.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Start the engine.
Enter the following menus: Powertrain / Engine / Active Test / Activate the VSV for Evap Control.
Operate the purge valve and check the airflow.
| Activate the VSV for Evap Control | Specified Condition |
| ON | Air flows |
| OFF | Air does not flow |
| Result | Proceed to |
| NG | A |
| OK | B |
| *a | VSV ON (Air flows) |
| *b | VSV OFF (Air does not flow) |
|
| ||||
| A | |
| 32.CHECK CONNECTOR CONNECTION CONDITION (ECM) |
Check the ECM connector connection condition.
|
| ||||
| OK | ||
| ||
| 33.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP DUTY) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump Duty.
When performing the Active Test, check for an operating sound from the fuel pump.
| Control the Fuel Pump Duty | Specified Condition |
| 20 or 80% | Operating sound heard |
| OFF | Operating sound not heard |
| Result | Proceed to |
| Abnormal | A |
| Normal | B |
|
| ||||
| A | |
| 34.INSPECT FUEL PUMP ASSEMBLY |
Inspect the fuel pump assembly .
|
| ||||
| OK | ||
| ||
| 35.CHECK FUEL SYSTEM |
Check the fuel system.
| Result | Proceed to |
| Abnormal | A |
| Normal | B |
|
| ||||
| A | |
| 36.CHECK FUEL SYSTEM |
Check for foreign matter such as iron particles around the fuel pump assembly (fuel pump, fuel pump filter and inside the fuel tank), and for signs that the fuel pump was stuck.
| Result | Proceed to |
| There is foreign matter or signs that fuel pump was stuck | A |
| There is no foreign matter and no signs that fuel pump was stuck | B |
|
| ||||
| A | |
| 37.CHECK FUEL SYSTEM |
Check the fuel system.
|
| ||||
| OK | ||
| ||
| 38.CHECK IGNITION SYSTEM |
Perform ignition system On-vehicle Inspection (Click here).
|
| ||||
| OK | |
| 39.READ FREEZE FRAME DATA |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item | Result | Suspected Area | Proceed to |
| Calculate Load | 110% or more of the current value of the vehicle*1 | Mass air flow meter | A |
| AFS Voltage B1S1 | Below 2.4 V*2 |
| B |
| Both freeze frame data items listed above | Values are other than above | - | C |
|
| ||||
|
| ||||
| A | |
| 40.CHECK MASS AIR FLOW METER |
Remove the mass airflow meter.
Check for foreign matter in the airflow passage of the mass air flow meter.
| Result | Proceed to |
| Visible foreign matter is not present | A |
| Visible foreign matter is present | B |
|
| ||||
| A | |
| 41.CHECK HARNESS AND CONNECTOR (ECM - MASS AIR FLOW METER) |
Disconnect the mass air flow meter connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A33-22 (VG) - C16-5 (VG) | Always | Below 1 Ω |
| A33-29 (E2G) - C16-4 (E2G) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| A33-22 (VG) or C16-5 (VG) - Body ground | Always | 10 kΩ or higher |
| A33-29 (E2G) or C16-4 (E2G) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 42.PERFORM DRIVE TEST |
Connect the GTS to the DLC3.
Start the engine and warm it up until the engine coolant temperature stabilizes.
Idle the engine.
Using the GTS, read the value of Calculate Load in the Data List.
| Data List | Specified Condition |
| Calculate Load | 90 to 110% of the current value of the vehicle |
|
| ||||
| OK | |
| 43.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR) |
![]() |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Start the engine, turn off all accessory switches and warm up the engine until the engine coolant temperature stabilizes.
Idle the engine.
Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor.
Read the output voltage from the air fuel ratio sensor when increasing and decreasing the fuel injection volume.
| GTS Display | Specified Condition |
| Control the Injection Volume for A/F Sensor (+12.5%) | Air fuel ratio sensor output voltage is below 2.0 V |
| Control the Injection Volume for A/F Sensor (-12.5%) | Air fuel ratio sensor output voltage is higher than 2.4 V |
| Result | Proceed to |
| Abnormal | A |
| Normal | B |
|
| ||||
| A | |
| 44.CHECK TERMINAL VOLTAGE (AIR FUEL RATIO SENSOR POWER SOURCE) |
Disconnect the air fuel ratio sensor connector.
![]() |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| C14-2 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector (to Air Fuel Ratio Sensor) |
|
| ||||
| OK | |
| 45.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM) |
Disconnect the air fuel ratio sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A34-18 (A1A-) - C14-4 (A1A-) | Always | Below 1 Ω |
| A34-19 (A1A+) - C14-3 (A1A+) | Always | Below 1 Ω |
| A34-5 (HA1A) - C14-2 (HA1A) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| A34-18 (A1A-) or C14-4 (A1A-) - Body ground | Always | 10 kΩ or higher |
| A34-19 (A1A+) or C14-3 (A1A+) - Body ground | Always | 10 kΩ or higher |
| A34-5 (HA1A) or C14-2 (HA1A) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 46.READ FREEZE FRAME DATA |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item | Result | Proceed to |
| Initial Engine Coolant Temp, Ambient Temp for A/C, Initial Intake Air Temp | Difference in temperature between each item is less than 10°C*1 | A |
| Difference in temperature between each item is 10°C or more*2 | B |
|
| ||||
| A | |
| 47.READ FREEZE FRAME DATA |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).

| Freeze Frame Data Item | Result | Suspected Area | Proceed to |
| Initial Engine Coolant Temp, Coolant Temp, Engine Run Time | Range A |
| A |
| Range B | Engine coolant temperature | B | |
| Range C | - | C |
|
| ||||
|
| ||||
| A | |
| 48.INSPECT THERMOSTAT |
| Result | Proceed to |
| Abnormal | A |
| Normal | B |
|
| ||||
| A | ||
| ||
| 49.READ FREEZE FRAME DATA |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item | Result | Suspected Area | Proceed to |
| Coolant Temp | 120°C or higher | Engine coolant temperature sensor | A |
| Coolant Temp, Ambient Temp for A/C | Engine coolant temperature is lower than outside temperature by 15°C or more | Engine coolant temperature sensor | |
| Both freeze frame data items listed above | Values are other than above | - | B |
|
| ||||
| A | |
| 50.INSPECT ENGINE COOLANT TEMPERATURE SENSOR |
| Result | Proceed to |
| Normal | A |
| Abnormal | B |
|
| ||||
| A | |
| 51.CHECK HARNESS AND CONNECTOR (ECM - ENGINE COOLANT TEMPERATURE SENSOR) |
Disconnect the ECM connector.
Disconnect the engine coolant temperature sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A36-30 (THW) - C40-2 (THW) | Always | Below 1 Ω |
| A36-29 (E1) - C40-1 (E2) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| A36-30 (THW) or C40-2 (THW) - Body ground | Always | 10 kΩ or higher |
| A36-29 (E1) or C40-1 (E2) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 52.CHECK IGNITION SYSTEM |
Perform ignition system On-vehicle Inspection (Click here).
|
| ||||
| OK | |
| 53.READ FREEZE FRAME DATA |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item | Result | Suspected Area | Proceed to |
| Total of ISC Learning Value and ISC Feedback Value | Below 80% of the current value of the vehicle | Intake air volume insufficient | A |
| 80% or more of the current value of the vehicle | B |
|
| ||||
| A | |
| 54.CHECK INTAKE SYSTEM |
Check for air leakage in the intake system [vacuum hose disconnection, cracks, damaged gaskets, etc.] (Click here).
|
| ||||
| OK | |
| 55.CHECK INTAKE SYSTEM |
Check the intake system.
| Result | Proceed to |
| Abnormal | A |
| Normal | B |
|
| ||||
| A | ||
| ||
| 56.PERFORM ACTIVE TEST USING GTS (CONTROL THE VVT LINEAR) |
Connect the GTS to the DLC3.
Turn the GTS on.
Warm up the engine.
Enter the following menus: Powertrain / Engine / Active Test / Control the VVT Linear (Bank1) or Control the VVT Linear (Bank2).
Check the engine speed while operating the camshaft timing oil control valve using the GTS.
| GTS Operation | Specified Condition |
| 0 deg (CA) | Normal engine speed |
| 36 deg (CA) | Engine idles roughly or stalls |
|
| ||||
| OK | |
| 57.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM) |
![]() |
Disconnect the camshaft timing oil control valve assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| C7-1 - Body ground | Ignition switch ON | 11 to 14 V |
| C24-1 - Body ground | Ignition switch ON | 11 to 14 V |
| *A | Bank 1 |
| *B | Bank 2 |
| *a | Front view of wire harness connector (to Camshaft Timing Oil Control Valve Assembly for Intake Side) |
Disconnect the ECM connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A36-17 (OC1) - C7-2 | Always | Below 1 Ω |
| A36-16 (OC2) - C24-2 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| A36-17 (OC1) or C7-2 - Body ground | Always | 10 kΩ or higher |
| A36-16 (OC2) or C24-2 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 58.PERFORM ACTIVE TEST USING GTS (CONTROL THE VVT EXHAUST LINEAR) |
Connect the GTS to the DLC3.
Turn the GTS on.
Warm up the engine.
Enter the following menus: Powertrain / Engine / Active Test / Control the VVT Exhaust Linear (Bank1) or Control the VVT Exhaust Linear (Bank2).
Check the engine speed while operating the camshaft timing oil control valve using the GTS.
| GTS Operation | Specified Condition |
| 0 deg (CA) | Normal engine speed |
| 51 deg (CA) | Engine idles roughly or stalls |
|
| ||||
| OK | |
| 59.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM) |
![]() |
Disconnect the camshaft timing oil control valve assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| C5-1 - Body ground | Ignition switch ON | 11 to 14 V |
| C23-1 - Body ground | Ignition switch ON | 11 to 14 V |
| *A | Bank 1 |
| *B | Bank 2 |
| *a | Front view of wire harness connector (to Camshaft Timing Oil Control Valve Assembly for Exhaust Side) |
Disconnect the ECM connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A36-7 (OE1) - C5-2 | Always | Below 1 Ω |
| A36-5 (OE2) - C23-2 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| A36-7 (OE1) or C5-2 - Body ground | Always | 10 kΩ or higher |
| A36-5 (OE2) or C23-2 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 60.READ FREEZE FRAME DATA |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item | Suspected Area | Proceed to | |
| IGN Advance | Knock Correct Learn Value | ||
| Differs from the current value of the vehicle by 10° or more | Less than 3° |
| A |
| 3° or more | - | B | |
| Differs from the current value of the vehicle by less than 10° | - | - | |
|
| ||||
| A | |
| 61.INSPECT ENGINE COOLANT TEMPERATURE SENSOR |
|
| ||||
| OK | |
| 62.CHECK HARNESS AND CONNECTOR (ECM - ENGINE COOLANT TEMPERATURE SENSOR) |
Disconnect the ECM connector.
Disconnect the engine coolant temperature sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A36-30 (THW) - C40-2 (THW) | Always | Below 1 Ω |
| A36-29 (E1) - C40-1 (E2) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| A36-30 (THW) or C40-2 (THW) - Body ground | Always | 10 kΩ or higher |
| A36-29 (E1) or C40-1 (E2) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 63.INSPECT MASS AIR FLOW METER (INTAKE AIR TEMPERATURE SENSOR) |
Inspect the mass air flow meter (Click here).
|
| ||||
| OK | |
| 64.READ VALUE USING GTS |
Connect the GTS to the DLC3.
Start the engine and warm it up until the engine coolant temperature stabilizes.
Idle the engine.
Using the GTS, read the value of IGN Advance and Knock Correct Learn Value in the Data List.
| Freeze Frame Data Item | Proceed to | |
| IGN Advance | Knock Correct Learn Value | |
| Differs from the current value of the vehicle by 10° or more | Less than 3° | A |
| 3° or more | B | |
| Differs from the current value of the vehicle by less than 10° | - | |
|
| ||||
| A | ||
| ||
| 65.CHECK TERMINAL VOLTAGE (FUEL INJECTOR POWER SOURCE) |
![]() |
Disconnect the fuel injector assembly connectors.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Cylinder | Tester Connection | Switch Condition | Specified Condition |
| No. 1 | C8-1 - Body ground | Ignition switch ON | 11 to 14 V |
| No. 2 | C30-1 - Body ground | Ignition switch ON | 11 to 14 V |
| No. 3 | C9-1 - Body ground | Ignition switch ON | 11 to 14 V |
| No. 4 | C31-1 - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector (to Fuel Injector Assembly (for Port Injection)) |
| *b | No. 1 cylinder |
| *c | No. 2 cylinder |
| *d | No. 3 cylinder |
| *e | No. 4 cylinder |
|
| ||||
| OK | |
| 66.CHECK IGNITION SYSTEM |
Perform ignition system On-vehicle Inspection (Click here).
|
| ||||
| OK | |
| 67.CHECK FREEZE FRAME DATA |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item | Suspected Area | Proceed to | |
| A/C Signal | Air Conditioner FB Val | ||
| A/C Signal display does not change from OFF | - | Except for A/C system | A |
| A/C Signal display changes from OFF to ON*1 | Value displayed for Air Conditioner FB Val does not increase | ||
| Value displayed for Air Conditioner FB Val increases | A/C system (Automatic A/C system) | B | |
| A/C system (Manual A/C system) | C | ||
|
| ||||
|
| ||||
| A | |
| 68.CHECK FREEZE FRAME DATA |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item | Suspected Area | Proceed to | |||
| Electric Load Feedback Val | Difference between Engine Speed and SPD (NT) | Vehicle Speed | |||
| Electrical Load Signal display changes from OFF to ON*3, or value displayed for Electric Load Feedback Val increases*1 | Value displayed for Electric Load Val changes | - | - | Electrical load signal circuit | C |
| Value displayed for Electric Load Val does not change | At least 1 of the 5 sets of freeze frame data is less than 100 rpm | Less than 30 km/h | Automatic transmission system | B | |
| 30 km/h or more | - | A | |||
| All 5 sets of freeze frame data are 100 rpm or more | - | - | A | ||
| Electrical Load Signal display does not change from OFF, or value displayed for Electric Load Feedback Val does not increase | - | At least 1 of the 5 sets of freeze frame data is less than 100 rpm | Less than 30 km/h | Automatic transmission system | B |
| 30 km/h or more | - | A | |||
| All 5 sets of freeze frame data are 100 rpm or more | - | - | A | ||
|
| ||||
|
| ||||
| A | |
| 69.CHECK FREEZE FRAME DATA |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item | Suspected Area | Proceed to | |
| Shift SW Status (P Range) Shift SW Status (N Range) | Neutral Position SW Signal | ||
| P and N position are both OFF in at least one data set | In D or R, NSW is ON | Park/neutral position switch assembly | A |
| In D or R, NSW is OFF | Automatic transmission system | B | |
| All 5 sets of freeze frame data are ON | - | - | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 70.CHECK FREEZE FRAME DATA |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item | Result | Suspected Area | Proceed to |
| Throttle Sensor Position, Calculate Load | Calculate Load decreases while Throttle Sensor Position increases | Mass air flow meter | A |
| Calculate Load does not decrease while Throttle Sensor Position increases | - | B |
|
| ||||
| A | |
| 71.CHECK MASS AIR FLOW METER |
Remove the mass air flow meter (Click here).
Check for foreign matter in the airflow passage of the mass airflow meter.
| Result | Proceed to |
| Visible foreign matter is not present | A |
| Visible foreign matter is present | B |
|
| ||||
| A | |
| 72.CHECK HARNESS AND CONNECTOR (ECM - MASS AIR FLOW METER) |
Disconnect the mass air flow meter connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A33-22 (VG) - C16-5 (VG) | Always | Below 1 Ω |
| A33-29 (E2G) - C16-4 (E2G) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| A33-22 (VG) or C16-5 (VG) - Body ground | Always | 10 kΩ or higher |
| A33-29 (E2G) or C16-4 (E2G) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 73.PERFORM DRIVE TEST |
Connect the GTS to the DLC3.
Start the engine and warm it up until the engine coolant temperature stabilizes.
Idle the engine.
Using the GTS, read the value of Calculate Load in the Data List.
| Data List | Specified Condition |
| Calculate Load | 90 to 110% of the current value of the vehicle |
|
| ||||
| OK | |
| 74.CHECK TERMINAL VOLTAGE (FUEL INJECTOR POWER SOURCE) |
![]() |
Disconnect the fuel injector assembly connectors.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Cylinder | Tester Connection | Switch Condition | Specified Condition |
| No. 1 | C8-1 - Body ground | Ignition switch ON | 11 to 14 V |
| No. 2 | C30-1 - Body ground | Ignition switch ON | 11 to 14 V |
| No. 3 | C9-1 - Body ground | Ignition switch ON | 11 to 14 V |
| No. 4 | C31-1 - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector (to Fuel Injector Assembly (for Port Injection)) |
| *b | No. 1 cylinder |
| *c | No. 2 cylinder |
| *d | No. 3 cylinder |
| *e | No. 4 cylinder |
|
| ||||
| OK | |
| 75.CHECK IGNITION SYSTEM |
Perform ignition system On-vehicle Inspection (Click here).
|
| ||||
| OK | |
| 76.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP DUTY) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump Duty.
When performing the Active Test, check for an operating sound from the fuel pump.
| Control the Fuel Pump Duty | Specified Condition |
| 25 or 80% | Operating sound heard |
| OFF | Operating sound not heard |
| Result | Proceed to |
| Abnormal | A |
| Normal | B |
|
| ||||
| A | |
| 77.INSPECT FUEL PUMP ASSEMBLY |
Inspect the fuel pump assembly (Click here).
|
| ||||
| OK | ||
| ||
| 78.CHECK FUEL SYSTEM |
Check the fuel system.
| Result | Proceed to |
| Abnormal | A |
| Normal | B |
|
| ||||
| A | |
| 79.CHECK FUEL SYSTEM |
Check for foreign matter such as iron particles around the fuel pump assembly (fuel pump, fuel pump filter and inside the fuel tank), and for signs that the fuel pump was stuck.
| Result | Proceed to |
| There is foreign matter or signs that fuel pump was stuck | A |
| There is no foreign matter and no signs that fuel pump was stuck | B |
|
| ||||
| A | |
| 80.CHECK FUEL SYSTEM |
Check the fuel system.
|
| ||||
| OK | ||
| ||
| 81.CLEAR DTC |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (Click here).
| NEXT | ||
| ||