Home › Engine / Hybrid System › N04C-VQ (ENGINE CONTROL) › ECD SYSTEM › 2017.01–2019.08
RM2850E _51 Engine / Hybrid System _073138 N04C-VQ ENGINE CONTROL _0355854 ECD SYSTEM J

N04C-VQ ENGINE CONTROL  ECD SYSTEM  Black Smoke Emitted  


WIRING DIAGRAM

Refer to DTC P0087 for fuel pressure sensor circuit (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>P0087).

Refer to DTC P0095 for intake air temperature sensor (after turbocharged) circuit (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>P0095).

Refer to DTC P0107 for manifold absolute pressure sensor circuit (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>P0107).

Refer to DTC P0112 for intake air temperature sensor circuit (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>P0112).

Refer to DTC P0115 for engine coolant temperature sensor circuit (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>P0115).

Refer to DTC P0201 for injector circuit (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>P0201).

Refer to DTC P0335 for crankshaft position sensor circuit (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>P0335).

Refer to DTC P2120 for accelerator pedal position sensor circuit (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>P2120).

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION)and initialization (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION ).

·

After replacing the injection or supply pump assembly, the ECM needs initialization (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).



HINT:

Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List values may occur depending on the measuring conditions or the vehicle's age. Do not assume the vehicle to be normal when the Data List outputs standard values. There may be concealed factors causing the malfunction.


PROCEDURE

1.CHECK OUTPUT DTC (RELATED TO ENGINE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.


Result:
Result Proceed to
DTC is not output A
DTCs related to the engine B



A

2.READ VALUE USING GTS (INJECTION VOLUME AND INJECTION FEED BACK VAL #1 TO #4)

B

2.READ VALUE USING GTS (INJECTION VOLUME AND INJECTION FEED BACK VAL #1 TO #4)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.


e.

Enter the following menus in order and read the values.

·

Injection Volume

·

Injection Feedback Val #1, #2, #3 and #4


Standard:
GTS Display Condition* Reference Value
Injection Volume Idling (No engine load) 5.0 to 15.0 mm3/st
Injection Feedback Val #1 Idling (No engine load) -2.0 to 2.0 mm3/st
Injection Feedback Val #2 Idling (No engine load) -2.0 to 2.0 mm3/st
Injection Feedback Val #3 Idling (No engine load) -2.0 to 2.0 mm3/st
Injection Feedback Val #4 Idling (No engine load) -2.0 to 2.0 mm3/st


HINT:

*: If no idling conditions are specified, the shift lever should be in the neutral position, and the A/C switch and all accessory switches should be off.



Result:
Proceed to
OK
NG



OK

3.PERFORM ENGINE SPEED ACCELERATION

NG

12.CHECK ECM TERMINAL VOLTAGE (THW TERMINAL)
3.PERFORM ENGINE SPEED ACCELERATION
HINT:

If the exhaust gas contains excessive black smoke, perform the following operations:


a.

Accelerate the engine speed to the maximum speed with no load 20 times.


b.

Check for black smoke in the exhaust gas.

Result:
Result Proceed to
Black smoke is not present A
Black smoke remains in the exhaust gas B


HINT:

Soot deposits in the exhaust system may cause excessive black smoke.




A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

4.CHECK AIR INTAKE SYSTEM AND EXHAUST SYSTEM
4.CHECK AIR INTAKE SYSTEM AND EXHAUST SYSTEM

Result:
Proceed to
OK
NG



OK

5.INSPECT EXHAUST RETARDER ASSEMBLY

NG

CHECK AND REPLACE LOCATIONS WHERE MALFUNCTIONS EXIST

5.INSPECT EXHAUST RETARDER ASSEMBLY
a.

Inspect the exhaust retarder assembly.


Result:
Proceed to
OK
NG



OK

6.CHECK EGR VALVE ASSEMBLY

NG

REPLACE EXHAUST RETARDER ASSEMBLY

6.CHECK EGR VALVE ASSEMBLY

Result:
Proceed to
OK
NG



OK

7.CHECK TURBOCHARGER SUB-ASSEMBLY

NG

7.CHECK TURBOCHARGER SUB-ASSEMBLY
a.

Check the turbocharger sub-assembly (Click hereEngine / Hybrid System>N04C-VQ (INTAKE)>INTAKE SYSTEM>ON-VEHICLE INSPECTION).


Result:
Proceed to
OK
NG



OK

8.READ VALUE USING GTS

NG

REPLACE TURBOCHARGER SUB-ASSEMBLY

8.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.


e.

Enter the following menus in order and read the values.

·

Fuel Press

·

Injection Volume

·

Main Injection Period

·

Pilot 2 Injection Period

·

Injection Feedback Val #1, #2, #3 and #4


Standard:
GTS Display Condition* Reference Value
Fuel Press Idling 20000 to 30000 kPa
Injection Volume Idling 5.0 to 15.0 mm3/st
Main Injection Period Idling 450 to 800 μs
Pilot 2 Injection Period Idling 500 to 600 μs
Injection Feedback Val #1 Idling -2.0 to 2.0 mm3/st
Injection Feedback Val #2 Idling -2.0 to 2.0 mm3/st
Injection Feedback Val #3 Idling -2.0 to 2.0 mm3/st
Injection Feedback Val #4 Idling -2.0 to 2.0 mm3/st


HINT:

If no idling conditions are specified, the shift lever should be in the neutral position, and the A/C switch and all accessory switches should be off.



Result:
Result Proceed to
Within reference value A
One of Injection Feedback Val #1 to #4 is not within reference value B
Other result C



A

9.CHECK CYLINDER COMPRESSION PRESSURE

B

C

12.CHECK ECM TERMINAL VOLTAGE (THW TERMINAL)
9.CHECK CYLINDER COMPRESSION PRESSURE
a.

Check the cylinder compression pressure (Click hereEngine / Hybrid System>N04C-VQ (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION).


Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY - INJECTOR DRIVER ASSEMBLY)

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

10.CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY - INJECTOR DRIVER ASSEMBLY)
a.

Check the wire harness between the injector assembly and injector driver assembly (IJ terminal).

i.

Disconnect the injector assembly connectors.


ii.

Disconnect the injector driver assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
i1-2 - B98-1 (IJ1+) Always Below 1 Ω
i2-2 - B98-6 (IJ2+) Always Below 1 Ω
i3-2 - B98-5 (IJ3+) Always Below 1 Ω
i4-2 - B95-3 (IJ4+) Always Below 1 Ω
i1-1 - B95-6 (IJ1-) Always Below 1 Ω
i2-1 - B95-4 (IJ2-) Always Below 1 Ω
i3-1 - B95-2 (IJ3-) Always Below 1 Ω
i4-1 - B95-5 (IJ4-) Always Below 1 Ω
i1-2 or B98-1 (IJ1+) - Body ground Always 10 kΩ or higher
i2-2 or B98-6 (IJ2+) - Body ground Always 10 kΩ or higher
i3-2 or B98-5 (IJ3+) - Body ground Always 10 kΩ or higher
i4-2 or B95-3 (IJ4+) - Body ground Always 10 kΩ or higher
i1-1 or B95-6 (IJ1-) - Body ground Always 10 kΩ or higher
i2-1 or B95-4 (IJ2-) - Body ground Always 10 kΩ or higher
i3-1 or B95-2 (IJ3-) - Body ground Always 10 kΩ or higher
i4-1 or B95-5 (IJ4-) - Body ground Always 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

11.PERFORM ACTIVE TEST USING GTS (INJECTOR CUT FOR IDENTIFYING MALFUNCTIONING CYLINDER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (INJECTOR ASSEMBLY - INJECTOR DRIVER ASSEMBLY)

11.PERFORM ACTIVE TEST USING GTS (INJECTOR CUT FOR IDENTIFYING MALFUNCTIONING CYLINDER)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Cylinder #1, #2, #3 and #4 Fuel Cut.


e.

Check the four cylinders in sequence to identify any faulty cylinders by performing the power-balance inspection.

Result:
Result Proceed to
Engine Idling becomes unstable A
Engine Idling does not change B


HINT:
·

If the engine idle does not change when an injector is disabled, the cylinder being tested is malfunctioning.

·

If the cylinder being tested is normal, there will be a significant change of idle speed when the fuel injection is stopped for that cylinder.





A

REPLACE INJECTOR DRIVER ASSEMBLY

B

12.CHECK ECM TERMINAL VOLTAGE (THW TERMINAL)
a.
A260250E41
1.333,0.281 1.74,0.51 0.406,0.229 1.833,0.271 2.24,0.5 0.406,0.229 1.313,1.5 1.625,0.792 true 2.479,1.531 2.177,0.865 true 0.135,0.125 0.448,0.323 0.313,0.198 10 false *a 1.375,0.313 1.781,0.51 0.406,0.198 10 false B105 1.885,0.313 2.292,0.51 0.406,0.198 10 false B104 1.104,1.563 1.792,1.771 0.688,0.208 10 false 9 (THW) 2.219,1.583 2.906,1.802 0.688,0.219 10 false 14 (E2)

Start the engine.


b.

Measure the voltage of the ECM connector.

Standard Voltage:
Tester Connection Condition Specified Condition
B105-9 (THW) - B104-14 (E2) Idling, engine coolant temperature between 60 and 120°C (140 and 248°F) 0.2 to 1.0 V


Text in Illustration
*a Component with harness connected
(ECM)


Result:
Proceed to
OK
NG



OK

13.CHECK ECM TERMINAL VOLTAGE (PIM TERMINAL)

NG

27.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
13.CHECK ECM TERMINAL VOLTAGE (PIM TERMINAL)
a.
A260250E42
1.854,0.188 2.26,0.417 0.406,0.229 1.656,1.521 1.927,0.74 true 2.479,1.531 2.177,0.865 true 0.135,0.125 0.448,0.323 0.313,0.198 10 false *a 1.885,0.219 2.292,0.417 0.406,0.198 10 false B104 1.448,1.583 2.01,1.802 0.563,0.219 10 false 5 (PIM) 2.208,1.583 2.781,1.792 0.573,0.208 10 false 14 (E2)

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B104-5 (PIM) - B104-14 (E2) Applied negative pressure of 93 kPa (700 mmHg, 27.5 in.Hg) 0.25 to 0.4 V
B104-5 (PIM) - B104-14 (E2) Applied positive pressure of 150 kPa (1125 mmHg, 44 in.Hg) 1.0 to 1.4 V


Text in Illustration
*a Component with harness connected
(ECM)


Result:
Proceed to
OK
NG



OK

14.CHECK ECM TERMINAL VOLTAGE (NE+ AND NE- TERMINALS)

NG

26.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
14.CHECK ECM TERMINAL VOLTAGE (NE+ AND NE- TERMINALS)
a.
A257466E17
2.333,0.281 2.823,0.573 0.49,0.292 2.656,0.969 2.979,1.76 true 2.583,0.969 1.823,1.771 true 2.406,0.354 2.885,0.531 0.479,0.177 10 false B103 0.094,0.052 0.302,0.25 0.208,0.198 10 false *a 0.427,1.979 0.656,2.156 0.229,0.177 10 false *b 2.75,2.292 3.427,2.542 0.677,0.25 10 false 5 V/DIV. 1.292,4.135 2.531,4.479 1.24,0.344 10 false 20 ms./DIV. 0.531,2.646 0.708,2.813 0.177,0.167 10 false G 0.438,3.333 0.688,3.521 0.25,0.188 10 false NE 2.896,2.823 3.271,3.031 0.375,0.208 10 false GND 2.896,3.385 3.26,3.583 0.365,0.198 10 false GND 2.771,1.823 3.313,2.01 0.542,0.188 10 false 7 (NE+) 1.583,1.802 2.094,1.99 0.51,0.188 10 false 8 (NE-)

While idling the engine, check the waveform between the specified terminals of the ECM connector using an oscilloscope.

Standard:
Tester Connection Specified Condition
B103-7 (NE+) - B103-8 (NE-) Correct waveform appears as shown

Tool Setting 5 V/DIV., 20 ms./DIV.
Condition Idling with warm engine


HINT:

The waveform varies depending on the engine speed.


Text in Illustration
*a Component with harness connected
(ECM)
*b G and NE Signal Waveform


Result:
Proceed to
OK
NG



OK

15.CHECK ECM TERMINAL VOLTAGE (VPA AND VPA2 TERMINALS)

NG

25.INSPECT CRANKSHAFT POSITION SENSOR
15.CHECK ECM TERMINAL VOLTAGE (VPA AND VPA2 TERMINALS)
a.
A260250E43
0.188,0.25 0.594,0.469 0.406,0.219 0.646,0.24 1.052,0.458 0.406,0.219 1.531,1.563 0.729,0.729 true 0.365,1.531 0.521,0.729 true 0.896,1.823 0.573,0.729 true 2.177,1.583 0.906,0.729 true 0.094,0.042 0.406,0.24 0.313,0.198 10 false *a 0.271,0.271 0.583,0.469 0.313,0.198 10 false A57 0.729,0.26 1.042,0.458 0.313,0.198 10 false A56 0.146,1.573 0.75,1.771 0.604,0.198 10 false 2 (VPA) 0.729,1.854 1.333,2.052 0.604,0.198 10 false 1 (VPA2) 1.302,1.594 1.906,1.792 0.604,0.198 10 false 5 (EPA) 1.99,1.604 2.625,1.802 0.635,0.198 10 false 3 (EPA2)

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Condition Accelerator Pedal Condition Specified Condition
A57-2 (VPA) - A56-5 (EPA) Released 0.6 to 1.0 V
Depressed 2.8 to 3.6 V
A57-1 (VPA2) - A56-3 (EPA2) Released 1.4 to 1.8 V
Depressed 3.6 to 4.4 V


Text in Illustration
*a Component with harness connected
(ECM)


Result:
Proceed to
OK
NG



OK

16.CHECK ECM TERMINAL VOLTAGE (THA TERMINAL)

NG

24.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)
16.CHECK ECM TERMINAL VOLTAGE (THA TERMINAL)
a.
A260250E44
1.333,0.281 1.74,0.51 0.406,0.229 1.833,0.271 2.24,0.5 0.406,0.229 1.313,1.51 1.521,0.802 true 2.479,1.531 2.177,0.865 true 0.135,0.125 0.448,0.323 0.313,0.198 10 false *a 1.375,0.313 1.781,0.51 0.406,0.198 10 false B105 1.885,0.313 2.292,0.51 0.406,0.198 10 false B104 1.104,1.563 1.792,1.771 0.688,0.208 10 false 10 (THA) 2.219,1.583 2.906,1.802 0.688,0.219 10 false 14 (E2)

Start the engine.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B105-10 (THA) - B104-14 (E2) Idling, intake air temperature at 0 to 80°C (32 to 176°F) 0.5 to 3.4 V


Text in Illustration
*a Component with harness connected
(ECM)


Result:
Proceed to
OK
NG



OK

17.CHECK ECM TERMINAL VOLTAGE (THIA TERMINAL)

NG

23.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY
17.CHECK ECM TERMINAL VOLTAGE (THIA TERMINAL)
a.
A260250E45
1.333,0.281 1.74,0.51 0.406,0.229 1.833,0.271 2.24,0.5 0.406,0.229 1.333,1.531 1.688,0.792 true 2.479,1.531 2.177,0.865 true 0.135,0.125 0.448,0.323 0.313,0.198 10 false *a 1.375,0.313 1.781,0.51 0.406,0.198 10 false B105 1.885,0.313 2.292,0.51 0.406,0.198 10 false B104 1.063,1.563 1.75,1.771 0.688,0.208 10 false 8 (THIA) 2.219,1.583 2.906,1.802 0.688,0.219 10 false 14 (E2)

Start the engine.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B105-8 (THIA) - B104-14 (E2) Idling, intake air temperature at 0 to 80°C (32 to 176°F) 1.0 to 4.4 V


Text in Illustration
*a Component with harness connected
(ECM)


Result:
Proceed to
OK
NG



OK

18.INSPECT ECM (PCR VOLTAGE)

NG

22.INSPECT INTAKE AIR TEMPERATURE SENSOR
18.INSPECT ECM (PCR VOLTAGE)
a.

Start the engine.


A260250E30
1.302,0.104 1.792,0.396 0.49,0.292 1.844,0.104 2.333,0.396 0.49,0.292 2.188,0.865 2.917,1.729 true 1.688,0.875 2.271,1.76 true 1.521,0.875 0.49,1.75 true 1.688,0.719 1.302,1.74 true 1.396,0.167 1.813,0.323 0.417,0.156 10 false B105 1.938,0.167 2.417,0.323 0.479,0.156 10 false B104 0.063,0.073 0.25,0.281 0.188,0.208 10 false *a 1.042,1.76 1.677,2.031 0.635,0.271 10 false 2 (PCR2) 0.292,1.76 0.99,2 0.698,0.24 10 false 16 (PCR1) 2.729,1.771 3.427,2.01 0.698,0.24 10 false 14 (E2) 2.125,1.771 2.76,2.042 0.635,0.271 10 false 14 (E21)

b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B105-16 (PCR1) - B104-14 (E2) Idling 1.7 to 2.2 V
B105-2 (PCR2) - B105-14 (E21) Idling 1.2 to 1.6 V


Text in Illustration
*a Component with harness connected
(ECM)


Result:
Proceed to
OK
NG



OK

NG

19.INSPECT COMMON RAIL ASSEMBLY (FUEL PRESSURE SENSOR)
19.INSPECT COMMON RAIL ASSEMBLY (FUEL PRESSURE SENSOR)
a.

Inspect the common rail assembly (fuel pressure sensor) (Click hereEngine / Hybrid System>N04C-VQ (FUEL)>COMMON RAIL>INSPECTION).


Result:
Proceed to
OK
NG



OK

20.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)

NG

REPLACE COMMON RAIL ASSEMBLY

20.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)
a.

Disconnect the ECM connector.


b.

Disconnect the fuel pressure sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B105-16 (PCR1) - m1-2 (PCR1) Always Below 1 Ω
B104-13 (VC) - m1-1 (VC1) Always Below 1 Ω
B104-14 (E2) - m1-3 (E1) Always Below 1 Ω
B105-2 (PCR2) - m1-5 (PCR2) Always Below 1 Ω
B105-13 (VC2) - m1-6 (VC2) Always Below 1 Ω
B105-14 (E21) - m1-4 (E2) Always Below 1 Ω
B105-16 (PCR1) or m1-2 (PCR1) - Body ground Always 10 kΩ or higher
B104-13 (VC) or m1-1 (VC1) - Body ground Always 10 kΩ or higher
B105-2 (PCR2) or m1-5 (PCR2) - Body ground Always 10 kΩ or higher
B105-13 (VC2) or m1-6 (VC2) - Body ground Always 10 kΩ or higher
B104-14 (E2) or m1-3 (E1) - Other terminals Always 10 kΩ or higher
B105-14 (E21) or m1-4 (E2) - Other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

21.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (FUEL PRESSURE SENSOR - ECM)

21.REPLACE ECM
a.

Replace the ECM (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECM>REMOVAL).

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).



b.

Check the volume of black smoke in the exhaust gas.

OK:

Black smoke is not present.



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE INJECTION OR SUPPLY PUMP ASSEMBLY

22.INSPECT INTAKE AIR TEMPERATURE SENSOR
a.

Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (INTAKE AIR TEMPERATURE SENSOR - ECM)

NG

23.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY
a.

Inspect the mass air flow meter sub-assembly (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>MASS AIR FLOW METER>INSPECTION).


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)

NG

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

24.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)
a.

Disconnect the accelerator pedal position sensor connector.


b.

Disconnect the ECM connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F9-2 (EPA2) - A56-3 (EPA2) Always Below 1 Ω
F9-1 (VPA2) - A57-1 (VPA2) Always Below 1 Ω
F9-4 (VCPA) - A56-6 (VCPA) Always Below 1 Ω
F9-3 (EPA) - A56-5 (EPA) Always Below 1 Ω
F9-5 (VPA) - A57-2 (VPA) Always Below 1 Ω
F9-2 (EPA2) or A56-3 (EPA2) - Body ground Always 10 kΩ or higher
F9-1 (VPA2) or A57-1 (VPA2) - Body ground Always 10 kΩ or higher
F9-4 (VCPA) or A56-6 (VCPA) - Body ground Always 10 kΩ or higher
F9-3 (EPA) or A56-5 (EPA) - Body ground Always 10 kΩ or higher
F9-5 (VPA) or A57-2 (VPA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE ACCELERATOR LINK ASSEMBLY (ACCELERATOR PEDAL POSITION SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)

25.INSPECT CRANKSHAFT POSITION SENSOR
a.

Inspect the crankshaft position sensor sensor (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>CRANKSHAFT POSITION SENSOR>INSPECTION).


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

NG

26.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
a.

Disconnect the manifold absolute pressure sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B18-2 (PIM) - B104-5 (PIM) Always Below 1 Ω
B18-3 (VC) - B104-13 (VC) Always Below 1 Ω
B18-1 (E) - B104-14 (E2) Always Below 1 Ω
B18-2 (PIM) or B104-5 (PIM) - Body ground Always 10 kΩ or higher
B18-3 (VC) or B104-13 (VC) - Body ground Always 10 kΩ or higher
B18-1 (E) or B104-14 (E2) - Other terminal Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)

27.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
a.
A126612E18
1.333,3.24 1.333,3.094 1.333,3.094 1.552,2.854 false 0.688,0.302 0.927,0.479 0.24,0.177 10 false *1 0.635,1.688 0.813,1.833 0.177,0.146 10 false 30 0.635,1.875 0.844,2.031 0.208,0.156 10 false 20 0.646,2.177 0.844,2.333 0.198,0.156 10 false 10 0.719,2.49 0.885,2.635 0.167,0.146 10 false 5 0.719,3.156 0.865,3.302 0.146,0.146 10 false 1 0.615,3.438 0.917,3.583 0.302,0.146 10 false 0.5 0.625,3.792 0.917,3.938 0.292,0.146 10 false 0.2 0.885,4.021 1.104,4.167 0.219,0.146 10 false -20 1.281,4.021 1.375,4.177 0.094,0.156 10 false 0 1.542,4.021 1.719,4.167 0.177,0.146 10 false 20 1.885,4.021 2.063,4.167 0.177,0.146 10 false 40 2.563,4.01 2.74,4.156 0.177,0.146 10 false 60 2.219,4.021 2.396,4.167 0.177,0.146 10 false 80 0.875,4.188 1.115,4.365 0.24,0.177 10 false (-4) 1.198,4.188 1.469,4.365 0.271,0.177 10 false (32) 1.51,4.188 1.781,4.365 0.271,0.177 10 false (68) 1.802,4.188 2.146,4.365 0.344,0.177 10 false (104) 2.51,4.177 2.854,4.354 0.344,0.177 10 false (212) 2.156,4.188 2.5,4.365 0.344,0.177 10 false (176) 0.281,4.063 0.531,4.417 0.25,0.354 10 false °C (°F) 0.719,2.719 0.875,2.885 0.156,0.167 10 false 3 0.719,2.917 0.875,3.083 0.156,0.167 10 false 2 0.865,1.563 1.104,1.74 0.24,0.177 10 false kΩ 2.396,2.958 2.635,3.135 0.24,0.177 10 false *2 0.615,3.625 0.917,3.771 0.302,0.146 10 false 0.3 0.625,3.979 0.927,4.125 0.302,0.146 10 false 0.1 1.25,3.271 1.49,3.448 0.24,0.177 10 false *a

Remove the engine coolant temperature sensor.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 2.32 to 2.59 kΩ
1 - 2 80°C (176°F) 0.31 to 0.326 kΩ


Text in Illustration
*1 Ohmmeter
*2 Engine Coolant Temperature Sensor
*a Acceptable

NOTICE:

When checking the sensor in water, keep the terminals dry. After the check, wipe the sensor dry.


HINT:

Alternative procedure: Connect an ohmmeter to the installed engine coolant temperature sensor and read the resistance. Use an infrared thermometer to measure the engine temperature in the immediate vicinity of the sensor. Compare these values against the resistance/ temperature graph. Change the engine temperature (warm up or cool down) and repeat the test.



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)

NG