12361E
1.INSTALL FRONT ENGINE MOUNTING INSULATOR
| *A | for LH Side |
| *B | for RH Side |
Install the 2 front engine mounting insulators to the front No. 1 engine mounting bracket RH and front No. 1 engine mounting bracket LH with the 2 nuts.
12281A
2.INSTALL ENGINE HANGER
3.REMOVE ENGINE FROM ENGINE STAND
Attach an engine sling device and hang the engine with a chain block.
Pay attention to the angle of the sling device as the engine assembly or No. 1 engine hanger may be damaged or deformed if the angle is incorrect.
Lift the engine and remove it from the engine stand.
Place the engine onto a work bench.
51100H
4.CONNECT FRONT FRAME ASSEMBLY
| *A | for LH Side |
| *B | for RH Side |
Install the front frame assembly to the engine assembly with the 4 bolts.
32101
5.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for Automatic Transmission)
35000
6.INSTALL AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission)
12380
7.INSTALL REAR ENGINE MOUNTING INSULATOR ASSEMBLY (for Automatic Transmission)
57209B
8.INSTALL REAR ENGINE MOUNTING MEMBER SUB-ASSEMBLY (for Automatic Transmission)
11361J
9.INSTALL FLYWHEEL HOUSING UNDER COVER (for Automatic Transmission)
10.INSTALL DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT (for Automatic Transmission)
16268L
11.CONNECT WATER BY-PASS PIPE ASSEMBLY (w/ ATF Warmer)
12.CONNECT ENGINE WIRE (for Automatic Transmission)
32921
13.INSTALL NO. 1 OIL COOLER INLET TUBE AND NO. 1 OIL COOLER OUTLET TUBE (w/o ATF Warmer)
32921
14.INSTALL NO. 1 OIL COOLER INLET TUBE AND NO. 1 OIL COOLER OUTLET TUBE (w/ ATF Warmer)
33493A
15.INSTALL TRANSMISSION OIL THERMOSTAT WITH TRANSMISSION OIL COOLER ASSEMBLY (w/ ATF Warmer)
32949
16.INSTALL OIL COOLER HOSE HEAT INSULATOR (w/ ATF Warmer)
17.INSTALL ENGINE ASSEMBLY WITH AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission)
|
Place Wooden Block or Plate Attachments |
Set the engine on an engine lifter.
Place wooden blocks or plate lift attachments so that the engine is level.
With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.
Never install attachments to the oil pan of the engine assembly or transmission as doing so may deform the oil pan.
Operate the engine lifter and install the engine assembly with automatic transmission assembly to the vehicle.
Make sure that the engine is clear of all wiring and hoses.
|
Bolt |
|
Nut |
Install the engine assembly with automatic transmission assembly to the vehicle with the 6 bolts and 2 nuts.
Install the rear engine mounting member with the 4 bolts.
Remove the 4 bolts and 2 engine hangers.
88539C
18.CONNECT NO. 2 COOLER UNIT DRAIN HOSE (for Automatic Transmission)
for LHD:
Attach the clamp and connect the No. 2 cooler unit drain hose.
for RHD:
Attach the clamp and connect the No. 2 cooler unit drain hose.
82122A
19.CONNECT NO. 2 ENGINE WIRE (for Automatic Transmission)
Connect the No. 2 engine wire to the vehicle body with the 2 bolts.
Connect the No. 2 engine wire to the automatic transmission assembly with the 2 bolts.
58041C
20.INSTALL FRONT NO. 1 FLOOR HEAT INSULATOR SUB-ASSEMBLY (for Automatic Transmission)
Install the front No. 1 floor heat insulator sub-assembly with the 3 bolts.
21.INSTALL ENGINE ASSEMBLY (for Manual Transmission)
|
Place Wooden Block or Plate Attachments |
Set the engine on an engine lifter.
Place wooden blocks or plate lift attachments so that the engine is level.
With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.
Never install attachments to the oil pan of the engine assembly or transmission as doing so may deform the oil pan.
Operate the engine lifter and install the engine assembly to the vehicle.
Make sure that the engine is clear of all wiring and hoses.
|
Bolt |
|
Nut |
Install the engine assembly to the vehicle with the 6 bolts and 2 nuts.
Remove the 4 bolts and 2 engine hangers.
88539C
22.CONNECT NO. 2 COOLER UNIT DRAIN HOSE (for Manual Transmission)
for LHD:
Attach the clamp and connect the No. 2 cooler unit drain hose.
for RHD:
Attach the clamp and connect the No. 2 cooler unit drain hose.
51107D
23.INSTALL REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY RH
Install the rear side rail reinforcement sub-assembly RH with the 4 bolts.
51108C
24.INSTALL REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY LH
Install the rear side rail reinforcement sub-assembly LH with the 4 bolts.
44402
25.CONNECT NO. 1 POWER STEERING OIL COOLER SUB-ASSEMBLY
| *A | for Type A |
| *B | for Type B |
for LHD:
Connect the No. 1 power steering oil cooler sub-assembly with the 2 bolts.
for RHD:
Connect the No. 1 power steering oil cooler sub-assembly with the 2 bolts.
for LHD:
Connect the return tube sub-assembly to the vehicle body with the bolt.
| *A | for LHD |
| *B | for RHD |
Connect the return tube sub-assembly to the vehicle body with the bolt.
53287B
26.INSTALL RADIATOR SUPPORT EXTENSION RH
| *A | for LHD |
| *B | for RHD |
Attach the 2 claws and install the radiator support extension RH.
53288B
27.INSTALL RADIATOR SUPPORT EXTENSION LH (for LHD)
Attach the 2 claws and install the radiator support extension LH.
13405
28.INSTALL FLYWHEEL SUB-ASSEMBLY (for Manual Transmission)
31250
29.INSTALL CLUTCH DISC ASSEMBLY (for Manual Transmission)
31210
30.INSTALL CLUTCH COVER ASSEMBLY (for Manual Transmission)
31210
31.INSPECT AND ADJUST CLUTCH COVER ASSEMBLY (for Manual Transmission)
32.INSTALL MANUAL TRANSMISSION ASSEMBLY (for Manual Transmission)
33.CONNECT WIRE HARNESS (for Manual Transmission)
12380
34.INSTALL REAR ENGINE MOUNTING INSULATOR ASSEMBLY (for Manual Transmission)
57209B
35.INSTALL REAR ENGINE MOUNTING MEMBER SUB-ASSEMBLY (for Manual Transmission)
58041C
36.INSTALL FRONT NO. 1 FLOOR HEAT INSULATOR SUB-ASSEMBLY (for Manual Transmission)
51446B
37.INSTALL NO. 2 ENGINE UNDER COVER BRACKET (for Manual Transmission)
33820B
38.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for Manual Transmission)
33825
39.INSTALL TRANSMISSION CONTROL CABLE INSULATOR (for Manual Transmission)
31482
40.INSTALL CLUTCH RELEASE CYLINDER TO FLEXIBLE HOSE TUBE (for Manual Transmission)
31470
41.INSTALL CLUTCH RELEASE CYLINDER ASSEMBLY (for Manual Transmission)
31490
42.INSTALL CLUTCH ACCUMULATOR ASSEMBLY (for Manual Transmission)
31482D
43.INSTALL CLUTCH RELEASE CYLINDER TO ACCUMULATOR TUBE (for Manual Transmission)
31349
44.INSTALL CLUTCH CABLE HEAT INSULATOR (for Manual Transmission)
45.INSTALL CLUTCH ACCUMULATOR HEAT INSULATOR SUB-ASSEMBLY (for Manual Transmission)
46.INSTALL FRONT AXLE ASSEMBLY LH
47.INSTALL FRONT AXLE ASSEMBLY RH
Use the same procedure described for the LH side.
48810
48.INSTALL FRONT STABILIZER LINK ASSEMBLY LH
48820B
49.INSTALL FRONT STABILIZER LINK ASSEMBLY RH
Use the same procedure described for the LH side.
48069
50.INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH
48068
51.INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH
Use the same procedure described for the LH side.
43512
52.INSTALL FRONT DISC
53.CONNECT FRONT DISC BRAKE CALIPER ASSEMBLY LH
54.CONNECT FRONT DISC BRAKE CALIPER ASSEMBLY RH
Use the same procedure described for the LH side.
45047
55.CONNECT TIE ROD END SUB-ASSEMBLY LH
for LHD:
Click hereSteering>STEERING GEAR / LINKAGE>STEERING GEAR (for LHD)>INSTALLATION
for RHD:
Click hereSteering>STEERING GEAR / LINKAGE>STEERING GEAR (for RHD)>INSTALLATION
45046
56.CONNECT TIE ROD END SUB-ASSEMBLY RH
Use the same procedure described for the LH side.
89543
57.INSTALL FRONT SPEED SENSOR LH
89542
58.INSTALL FRONT SPEED SENSOR RH
Use the same procedure described for the LH side.
59.CONNECT INTERMEDIATE SHAFT ASSEMBLY
for LHD:
Click hereSteering>STEERING GEAR / LINKAGE>STEERING GEAR (for LHD)>INSTALLATION
for RHD:
Click hereSteering>STEERING GEAR / LINKAGE>STEERING GEAR (for RHD)>INSTALLATION
11363A
60.INSTALL FLYWHEEL HOUSING SIDE COVER
28100
61.INSTALL STARTER ASSEMBLY
28192
62.INSTALL STARTER COVER
37100
63.INSTALL PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY
for Standard Roof:
Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>PROPELLER SHAFT ASSEMBLY (for Standard Roof)>INSTALLATION
for High Roof:
Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>PROPELLER SHAFT ASSEMBLY (for High Roof)>INSTALLATION
51569A
64.INSTALL PROPELLER SHAFT GUARD
for Standard Roof:
Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>PROPELLER SHAFT ASSEMBLY (for Standard Roof)>INSTALLATION
for High Roof:
Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>PROPELLER SHAFT ASSEMBLY (for High Roof)>INSTALLATION
17150
65.INSTALL EXHAUST MANIFOLD ASSEMBLY LH
17362
66.INSTALL NO. 2 AIR TUBE (w/ Secondary Air Injection System)
17119
67.INSTALL NO. 2 MANIFOLD STAY
17140
68.INSTALL EXHAUST MANIFOLD ASSEMBLY RH
17361N
69.INSTALL NO. 1 AIR TUBE (w/ Secondary Air Injection System)
11409
70.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE
Install the O-ring to the engine oil level dipstick guide.
Install the engine oil level dipstick guide with the bolt.
Install the engine oil level dipstick.
17118
71.INSTALL MANIFOLD STAY
17450B
72.INSTALL FRONT NO. 2 EXHAUST PIPE ASSEMBLY
17410
73.INSTALL FRONT EXHAUST PIPE ASSEMBLY
17403
74.INSTALL FRONT NO. 3 EXHAUST PIPE SUB-ASSEMBLY
17190
75.INSTALL INTAKE AIR SURGE TANK ASSEMBLY
22267A
76.INSTALL THROTTLE BODY BRACKET
17125
77.INSTALL NO. 1 SURGE TANK STAY
17126
78.INSTALL NO. 2 SURGE TANK STAY
17346
79.CONNECT NO. 6 AIR INJECTION SYSTEM HOSE (w/ Secondary Air Injection System)
Connect the No. 6 air injection system hose to the air tube assembly, and slide the clip to secure it.
16631D
80.INSTALL NO. 1 IDLER PULLEY BRACKET (w/o Air Conditioning System)
Install the No. 1 idler pulley bracket with the 3 bolts.
16603K
81.INSTALL IDLER PULLEY SUB-ASSEMBLY (w/o Air Conditioning System)
| *1 | Bolt |
| *2 | Plate Washer |
| *3 | Idler Pulley Sub-assembly |
| *4 | No. 1 Idler Pulley Bracket |
Install the 2 plate washers and idler pulley sub-assembly to the No. 1 idler pulley bracket with the bolt as shown in the illustration.
88320
82.INSTALL COMPRESSOR ASSEMBLY WITH MAGNET CLUTCH (w/ Air Conditioning System)
88704
83.CONNECT SUCTION HOSE SUB-ASSEMBLY (w/ Air Conditioning System)
88703
84.CONNECT DISCHARGE HOSE SUB-ASSEMBLY (w/ Air Conditioning System)
27020
85.INSTALL GENERATOR ASSEMBLY
44310
86.CONNECT VANE PUMP ASSEMBLY
87.CONNECT VACUUM HOSE ASSEMBLY
23901
88.CONNECT FUEL TUBE SUB-ASSEMBLY
Connect the 2 fuel tube sub-assemblies.
Click hereEngine / Hybrid System>7GR-FKS (FUEL)>FUEL SYSTEM>PRECAUTION
Install the No. 2 fuel pipe clamp.
87245A
89.CONNECT HEATER WATER HOSE ASSEMBLY
Connect the 2 heater water hose assemblies to the water pipe, and slide the 2 clamps to secure the hoses.
90.CONNECT WIRE HARNESS
Attach the claw and 3 connectors from the No. 1 engine room relay block.
Attach the clamp and connect the wire harness to the bracket.
Connect the wire harness to the body with the 2 bolts.
Connect the connector.
Attach the 3 clamps and connect the wire harness to the No. 1 engine room relay block and bracket.
Connect the 2 wire harnesses to the No. 1 engine room relay assembly with the 2 bolts.
Attach the claw and install the relay block cover to the No. 1 engine room relay block.
Attach the 2 claws and install the upper No. 1 relay block cover to the No. 1 engine room relay block.
82121
91.CONNECT ENGINE WIRE
Pass the engine wire into the cabin.
Attach the grommet to the body.
| *A | for LHD |
| *B | for RHD |
for LHD:
Attach the 2 clamps to connect the engine wire to the bracket.
for RHD:
Attach the clamp to connect the engine wire to the bracket.
| *A | for LHD |
| *B | for RHD |
Connect the 2 connectors to the instrument panel wire.
Connect the 4 connectors to the ECM.
Click hereEngine / Hybrid System>7GR-FKS (ENGINE CONTROL)>ECM>INSTALLATION
16711
92.INSTALL FAN SHROUD
32941
93.INSTALL NO. 1 OIL COOLER INLET HOSE AND NO. 1 OIL COOLER OUTLET HOSE (for Automatic Transmission)
16572D
94.INSTALL NO. 2 RADIATOR HOSE
16571C
95.INSTALL NO. 1 RADIATOR HOSE
16470
96.INSTALL RADIATOR RESERVE TANK ASSEMBLY
44360
97.CONNECT VANE PUMP OIL RESERVOIR ASSEMBLY
98.INSTALL FRONT BUMPER
for Wagon:
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER (for Wagon)>INSTALLATION
except Wagon:
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER (except Wagon)>INSTALLATION
17881
99.INSTALL AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE
Install the air cleaner assembly with air cleaner hose with the 3 bolts.
Tighten the hose clamp.
Connect the No. 2 PCV hose to the No. 1 air cleaner hose, and slide the clamp to secure the hose.
Attach the 2 wire harness clamps.
Connect the mass air flow meter sub-assembly connector.
17751
100.INSTALL NO. 1 AIR CLEANER INLET
11209
101.INSTALL V-BANK COVER SUB-ASSEMBLY (w/ Cover)
Attach the 3 clips to install the V-bank cover sub-assembly.
Securely attach the clips.
If the clips are forcibly attached or struck with an object, they may be damaged.
55701J
102.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY
| *A | for LHD |
| *B | for RHD |
Install the outer cowl top panel sub-assembly with the 10 bolts.
| *A | for LHD |
| *B | for RHD |
for LHD:
Attach the 6 clamps and connect the wire harness to the outer cowl top panel sub-assembly.
for RHD:
Attach the 7 clamps and connect the wire harness to the outer cowl top panel sub-assembly.
55738D
103.INSTALL NO. 2 HEATER AIR DUCT SPLASH SHIELD SEAL
| *A | for LHD |
| *B | for RHD |
for LH Side:
Attach the 2 claws and install the No. 2 heater air duct splash shield seal to the outer cowl top panel sub-assembly.
| *A | for LHD |
| *B | for RHD |
for RH Side:
Attach the 2 claws and install the No. 2 heater air duct splash shield seal to the outer cowl top panel sub-assembly.
47220D
104.CONNECT BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY
| *A | for LHD |
| *B | for RHD |
Connect the brake master cylinder reservoir assembly with the 2 bolts.
| *A | for LHD |
| *B | for RHD |
Disconnect the connector.
for RHD:
Attach the clamp and connect the wire harness to the brake master cylinder reservoir assembly.
85110
105.INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY
106.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
107. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
108.BLEED CLUTCH PIPE LINE (for Manual Transmission)
Click hereDrivetrain>CLUTCH>CLUTCH SYSTEM>BLEEDING
109.INSPECT FOR BRAKE FLUID LEAK (for Manual Transmission)
110.CHECK FLUID LEVEL IN RESERVOIR (for Manual Transmission)
31301
111.INSPECT AND ADJUST CLUTCH PEDAL SUB-ASSEMBLY (for Manual Transmission)
112.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT (w/ Air Conditioning System)
113.ADD ENGINE OIL
114.ADD MANUAL TRANSMISSION OIL (for Manual Transmission)
115.INSPECT MANUAL TRANSMISSION OIL (for Manual Transmission)
116.ADD AUTOMATIC TRANSMISSION FLUID (for Automatic Transmission)
117.ADD ENGINE COOLANT
118.ADJUST AUTOMATIC TRANSMISSION FLUID (for Automatic Transmission)
119. WARM UP ENGINE (w/ Air Conditioning System)
120.INSPECT FOR REFRIGERANT GAS LEAK (w/ Air Conditioning System)
121.INSPECT FOR FUEL LEAK
122.INSPECT FOR COOLANT LEAK
123.INSPECT FOR ENGINE OIL LEAK
124.INSPECT FOR EXHAUST GAS LEAK
125.INSPECT ENGINE OIL LEVEL
126.INSPECT ENGINE COOLANT LEVEL IN RESERVOIR TANK
127.PERFORM RESET MEMORY (for Automatic Transmission)
128.INSTALL FRONT WHEELS
129. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
130.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
131.INSPECT IGNITION TIMING
132.INSPECT ENGINE IDLE SPEED
133.INSPECT CO/HC
51773E
134.INSTALL STEP PLATE COVER RH (w/ Cover)
| *A | for Automatic Transmission |
| *B | for Manual Transmission |
Install the step plate cover RH with the 4 clips and 5 bolts.
51407A
135.INSTALL NO. 3 ENGINE UNDER COVER SUB-ASSEMBLY (w/ No. 3 Engine Under Cover Sub-assembly)
| *A | for Manual Transmission |
| *B | for Automatic Transmission |
Install the No. 3 engine under cover sub-assembly with the 4 bolts.
51405A
136.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
w/ No. 2 Engine Under Cover Sub-assembly:
Attach the guide and install the No. 1 engine under cover sub-assembly.
Install the 10 clips.
w/o No. 2 Engine Under Cover Sub-assembly:
Attach the guide and install the No. 1 engine under cover sub-assembly.
Install the 12 clips and 2 bolts.
52618
137.INSTALL LOWER FRONT BUMPER ABSORBER
|
Bolt |
|
Screw |
Attach the 2 guides and install the lower front bumper absorber.
Install the 4 bolts, 4 screws and 4 clips.
51406A
138.INSTALL NO. 2 ENGINE UNDER COVER SUB-ASSEMBLY (w/ No. 2 Engine Under Cover Sub-assembly)
Install the No. 2 engine under cover sub-assembly with the 6 clips and 7 bolts.
53106B
139.INSTALL RADIATOR COVER SUB-ASSEMBLY
for Wagon:
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>RADIATOR GRILLE (for Wagon)>INSTALLATION
except Wagon:
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>RADIATOR GRILLE (except Wagon)>INSTALLATION