Home › Engine / Hybrid System › 1GD-FTV (ENGINE MECHANICAL) › CAMSHAFT (w/ EGR Cooler) › 2020.05–2021.07
RM35X0E _51 Engine / Hybrid System _079219 1GD-FTV ENGINE MECHANICAL _0384424 CAMSHAFT(w/ EGR Cooler) A

1GD-FTV ENGINE MECHANICAL  CAMSHAFT(w/ EGR Cooler)  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.

Replaced Parts (A) Pipes Requiring New Replacement
Injector assembly (including shuffling the injector assemblies between the cylinders)
·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly


Supply pump assembly Fuel inlet pipe sub-assembly
·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Cylinder head gasket

·

Timing chain case assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly

·

Fuel inlet pipe sub-assembly



·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.

·

The injector assembly is a precision instrument. Do not use the injector assembly if it is struck or dropped.

·

The supply pump assembly is a precision instrument. Do not use the supply pump assembly if it is struck or dropped.

·

The common rail assembly is a precision instrument. Do not use the common rail assembly if it is struck or dropped.

·

Hold the supply pump assembly itself during removal and installation. Do not hold the pre-stroke control valve or fuel pipe, etc.

·

Hold the common rail assembly itself during removal and installation. Do not hold the pressure discharge valve or fuel pressure sensor, etc.

·

Make sure foreign matter does not enter the fuel path.



PROCEDURE

Hide 1.INSTALL CAMSHAFT

a.
A346673C01
1.573,0.594 0.99,0.344 0.99,0.344 0.74,0.344 true 0.938,0.979 0.51,1.125 0.51,1.125 0.344,1.125 true 2.656,1.573 3.073,1.573 true 0.573,0.25 0.781,0.406 0.208,0.156 10 false *1 0.177,1.021 0.427,1.177 0.25,0.156 10 false *2 3.094,1.469 3.323,1.625 0.229,0.156 10 false *3
*1 Valve Rocker Arm Sub-assembly
*2 Valve Stem Cap
*3 Valve Lash Adjuster Assembly


Check that the valve rocker arm sub-assembly is firmly set to the valve lash adjuster assembly.


b.

Apply a light coat of engine oil to the camshaft journals of the cylinder head sub-assembly and the thrust portion of the camshaft.


c.
A346674C01
1.677,0.156 1.865,0.156 1.865,0.156 2.26,0.333 true 2.302,0.458 2.896,0.573 2.896,0.573 3.031,0.573 true 1.5,0.063 1.729,0.25 0.229,0.188 10 false *a 3.063,0.49 3.292,0.677 0.229,0.188 10 false *b
*a Paint Mark
*b Timing Mark


Align the paint mark of the No. 2 chain sub-assembly and timing mark of the camshaft timing sprocket, and install the camshaft timing sprocket to the No. 2 chain sub-assembly.

HINT:

Make sure the timing mark of the camshaft timing sprocket faces the front side.



d.
A349446

Align the knock pin of the No. 1 camshaft to the groove of the sprocket, install the No. 1 camshaft to the camshaft timing sprocket, and set the bolt.


e.
A346675C01
1.323,0.396 1.583,0.135 1.583,0.135 1.76,0.135 true 1.313,0.5 0.552,0.219 0.552,0.219 0.354,0.219 true 1.771,0.042 2.021,0.208 0.25,0.167 10 false *a 0.167,0.125 0.365,0.292 0.198,0.167 10 false *b
*a Paint Mark
*b Timing Mark


Align the paint mark of the No. 2 chain sub-assembly and timing mark of the camshaft timing sprocket, and install the camshaft timing sprocket to the No. 2 chain sub-assembly.

HINT:

Make sure the timing mark of the camshaft timing sprocket faces the front side.



f.
A349447

Align the knock pin of the No. 2 camshaft to the groove of the sprocket, install the No. 2 camshaft to the camshaft timing sprocket, and set the bolt.

HINT:
A344474C01
0.667,1.583 0.729,1.854 0.729,1.854 0.813,1.854 true 0.667,1.146 0.719,0.885 0.719,0.885 0.802,0.885 true 0.833,1.75 1.146,1.948 0.313,0.198 10 false *a 0.823,0.792 1.135,0.99 0.313,0.198 10 false *a
*a Groove


The groove is at the rear end of the No. 2 camshaft.



g.
A344473C01
1.021,0.771 0.625,0.375 0.625,0.375 0.458,0.375 true 2.396,0.781 2.729,0.427 2.729,0.427 2.896,0.427 true 2.406,0.917 2.385,1.594 true 1.021,0.917 1.021,1.583 true 0.292,0.271 0.5,0.438 0.208,0.167 10 false *a 0.958,1.594 1.188,1.76 0.229,0.167 10 true *b 2.927,0.313 3.135,0.479 0.208,0.167 10 false *a 2.333,1.604 2.563,1.771 0.229,0.167 10 true *b
*a Paint Mark
*b Timing Mark


Check the timing mark of the camshaft timing sprocket and paint mark of the No. 2 chain sub-assembly.


h.
A344475

Set the No. 1 camshaft bearing cap and 8 No. 2 camshaft bearing caps to the cylinder head sub-assembly as shown in the illustration.


i.

Temporarily install the 20 bolts.


j.
A344476C01
1.75,0.531 1.896,0.708 0.146,0.177 10 true 4 1.75,0.885 1.896,1.063 0.146,0.177 10 true 3 1.75,1.458 1.896,1.635 0.146,0.177 10 true 2 1.75,1.115 1.896,1.292 0.146,0.177 10 true 1 2.406,1.115 2.552,1.292 0.146,0.177 10 true 5 2.406,1.458 2.552,1.635 0.146,0.177 10 true 6 2.385,0.531 2.531,0.708 0.146,0.177 10 true 8 2.406,0.906 2.552,1.083 0.146,0.177 10 true 7 1.104,1.458 1.333,1.635 0.229,0.177 10 true 10 1.104,1.125 1.25,1.302 0.146,0.177 10 true 9 1.104,0.896 1.333,1.073 0.229,0.177 10 true 11 1.115,0.531 1.344,0.708 0.229,0.177 10 true 12 3.031,1.104 3.26,1.281 0.229,0.177 10 true 13 3.031,1.458 3.26,1.635 0.229,0.177 10 true 14 3.031,0.906 3.26,1.083 0.229,0.177 10 true 15 3.052,0.531 3.281,0.708 0.229,0.177 10 true 16 0.583,1.417 0.781,1.594 0.198,0.177 10 true 17 0.583,0.615 0.771,0.792 0.188,0.177 10 true 18 0.583,1.729 0.771,1.917 0.188,0.188 10 true 19 0.573,0.281 0.771,0.458 0.198,0.177 10 true 20
V100135

Bolt A
V100136

Bolt B


Uniformly tighten the 20 bolts in several steps in the order shown in the illustration.

Torque:
for bolt A : 10 N*m (102 kgf*cm, 7 ft.*lbf)
for bolt B : 21 N*m (214 kgf*cm, 15 ft.*lbf)


k.
A346684C01
1.917,0.667 2.896,0.667 true 0.573,2.969 1.427,2.969 true 2.927,0.563 3.167,0.75 0.24,0.188 10 false *1 0.375,2.865 0.615,3.052 0.24,0.188 10 false *2
*1 No. 1 Camshaft
*2 No. 2 Camshaft


Hold the hexagonal portion of the No. 1 camshaft and No. 2 camshaft with a wrench, and tighten the 2 bolts.

Torque:
81 N*m (826 kgf*cm, 60 ft.*lbf)

NOTICE:

Be careful not to damage the cylinder head sub-assembly with the wrench.



l.

Remove the pin from the No. 2 chain tensioner assembly.


m.

Install a new gasket and the oil pump relief valve plug to the timing chain cover.

Torque:
46 N*m (469 kgf*cm, 34 ft.*lbf)


Hide 13566B 2.INSTALL TIMING CHAIN GUIDE

a.

Install the timing chain guide to the cylinder head sub-assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 11382C 3.INSTALL CAMSHAFT OIL SEAL RETAINER

Hide 29300 4.TEMPORARILY INSTALL VACUUM PUMP ASSEMBLY

Hide 5.INSTALL NO. 3 CAMSHAFT BEARING CAP

a.

Clean and degrease the contact surfaces of the cylinder head sub-assembly and No. 3 camshaft bearing cap.


b.
A346676C01
0.667,1.417 0.417,1.417 false 3.01,1.417 2.76,1.417 false 0.25,1.302 0.458,1.458 0.208,0.156 10 false *a 3.021,1.313 3.229,1.469 0.208,0.156 10 false *a
*a Seal Packing


Apply seal packing to the specified areas as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

3.0 mm (0.118 in.)


NOTICE:
·

Do not allow seal packing to contact the oil passage of the No. 3 camshaft bearing cap.

·

After applying seal packing, install the No. 3 camshaft bearing cap within 3 minutes and tighten the bolts within 10 minutes.

·

Do not start the engine for at least 2 hours after installation.




c.

Install the No. 3 camshaft bearing cap with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


d.

Wipe off excess seal packing from between the No. 3 camshaft bearing cap and cylinder head sub-assembly.


Hide 29300 6.INSTALL VACUUM PUMP ASSEMBLY

Hide 11201 7.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 23682 8.INSTALL NOZZLE HOLDER GASKET

Hide 23670 9.TEMPORARILY INSTALL INJECTOR ASSEMBLY

Hide 10.TEMPORARILY INSTALL NO. 1 INJECTION PIPE SUB-ASSEMBLY AND NO. 2 INJECTION PIPE SUB-ASSEMBLY

Hide 23670 11.TIGHTEN INJECTOR ASSEMBLY

Hide 12.TIGHTEN NO. 1 INJECTION PIPE SUB-ASSEMBLY AND NO. 2 INJECTION PIPE SUB-ASSEMBLY

Hide 23760 13.INSTALL NOZZLE LEAKAGE PIPE ASSEMBLY

Hide 15.INSTALL WIRING HARNESS CLAMP BRACKET

Hide 17.INSTALL NO. 1 EGR COOLER AND NO. 2 EGR VALVE ASSEMBLY WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY

Hide 25601 18.CONNECT EGR PIPE WITH COOLER SUB-ASSEMBLY (for Double Actuator EGR Bypass Valve)

Hide 25601 19.INSTALL NO. 1 EGR PIPE SUB-ASSEMBLY (for Single Actuator EGR Bypass Valve)

Hide 16209 20.CONNECT NO. 4 WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 16206B 21.INSTALL NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 89425D 23.INSTALL NO. 5 EXHAUST GAS TEMPERATURE SENSOR (w/ Exhaust Gas Temperature Sensor for EGR)

Hide 89421C 30.INSTALL DIESEL TURBO PRESSURE SENSOR

Hide 87209 32.INSTALL WATER HOSE SUB-ASSEMBLY (w/ Heater)

Hide 26100G 33.INSTALL DIESEL THROTTLE BODY ASSEMBLY

Hide 17303T 34.INSTALL AIR PIPE SUB-ASSEMBLY

Hide 25760F 35.INSTALL VACUUM TRANSMITTING HOSE ASSEMBLY

Hide 12601B 36.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY (w/ Cover)

Hide 16400 37.INSTALL RADIATOR ASSEMBLY

Hide 32922A 38.CONNECT OIL COOLER OUTLET HOSE (for Automatic Transmission)

Hide 32921D 39.CONNECT OIL COOLER INLET HOSE (for Automatic Transmission)

Hide 53205 40.INSTALL UPPER RADIATOR SUPPORT SUB-ASSEMBLY

Hide 86510 41.INSTALL HIGH PITCHED HORN ASSEMBLY (for 2-piece Type)

Hide 86520 42.INSTALL LOW PITCHED HORN ASSEMBLY

Hide 51466 43.INSTALL UPPER RADIATOR SUPPORT BRACE LH (for Wagon)

Hide 51465 44.INSTALL UPPER RADIATOR SUPPORT BRACE RH (for Wagon)

Hide 53285N 45.INSTALL RADIATOR SIDE AIR SEAL RH (for Wagon)

Hide 53286F 46.INSTALL RADIATOR SIDE AIR SEAL LH (for Wagon)

Hide 16546 47.INSTALL RADIATOR PROTECTOR (w/o Air Conditioning System)

Hide 53209B 48.INSTALL HOOD LOCK SUPPORT BRACE SUB-ASSEMBLY

Hide 88590 49.INSTALL BLOWER ASSEMBLY WITH SHROUD (w/ Condenser Fan)

Hide 17311B 50.INSTALL NO. 1 AIR INLET DUCT

Hide 16572D 53.INSTALL NO. 2 RADIATOR HOSE

Hide 88359 55.INSTALL VISCOUS HEATER V BELT (w/ Viscous Heater)

Hide 16515A 56.CONNECT INTERCOOLER COOLING WATER PIPE ASSEMBLY (for Water Cooled Type Intercooler)

Hide 161B0 57.INSTALL ELECTRIC WATER PUMP ASSEMBLY (for Water Cooled Type Intercooler)

Hide 165A0 58.INSTALL NO.1 INTERCOOLER COOLING WATER HOSE ASSEMBLY (for Water Cooled Type Intercooler)

Hide 16552C 59.INSTALL NO.2 INTERCOOLER COOLING WATER HOSE (for Water Cooled Type Intercooler)

Hide 16571C 60.INSTALL NO. 1 RADIATOR HOSE

Hide 16640 61.INSTALL INTERCOOLER RESERVE TANK ASSEMBLY (for Water Cooled Type Intercooler)

Hide 16470 62.INSTALL RADIATOR RESERVE TANK ASSEMBLY

Hide 44360 64.CONNECT VANE PUMP OIL RESERVOIR ASSEMBLY

Hide 17751 65.INSTALL NO. 1 AIR CLEANER INLET

Hide 17940D 66.INSTALL INTERCOOLER ASSEMBLY (for Water Cooled Type Intercooler)

Hide 16278 67.INSTALL NO. 2 WATER BY-PASS PIPE (for Water Cooled Type Intercooler)

Hide 17030 68.INSTALL AIR HOSE ASSEMBLY (for Water Cooled Type Intercooler)

Hide 17360E 69.INSTALL NO. 1 AIR TUBE ASSEMBLY (for Water Cooled Type Intercooler)

Hide 70.INSTALL NO. 2 INTERCOOLER COOLING WATER PIPE ASSEMBLY (for Water Cooled Type Intercooler)

Hide 16551C 71.CONNECT NO. 1 INTERCOOLER COOLING WATER HOSE (for Water Cooled Type Intercooler)

Hide 12601B 72.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY (for Water Cooled Type Intercooler)

Hide 53106B 73.INSTALL RADIATOR COVER SUB-ASSEMBLY

Hide 55701J 74.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 85110 75.INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY

Hide 76.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 77. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


Hide 78.ADD ENGINE COOLANT

Hide 51405A 84.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 52618 85.INSTALL LOWER FRONT BUMPER ABSORBER

Hide 51406A 86.INSTALL NO. 2 ENGINE UNDER COVER SUB-ASSEMBLY (w/ No. 2 Engine Under Cover Sub-assembly)