Home › BRAKE › BRAKE CONTROL › ELECTRONICALLY CONTROLLED BRAKE SYSTEM

ELECTRONICALLY CONTROLLED BRAKE SYSTEM > PROBLEM SYMPTOMS TABLE

for Preparation Click here


HINT:
Use the table below to help determine the cause of the problem symptom. The potential causes of the symptoms are listed in order of probability in the "Suspected area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.


Electronically controlled brake system 
Symptom
Suspected Area
See page
ABS does not operate, BA does not operate, EBD does not operate
1. Check the DTC again and make sure that the normal code is output.
Click here
2. IG power source circuit and ground circuit
Click here
3. Front speed sensor circuit
Click here
4. Rear speed sensor circuit
Click here
5. Check the brake actuator with Techstream. (Check brake actuator operation using the Active Test function.) If abnormal, check the hydraulic circuit for leakage.
Click here
6. If the symptoms still occur even after the above suspected areas are inspected and proved to be normal, replace the skid control ECU.
Click here
ABS does not operate efficiently, BA does not operate efficiently, EBD does not operate efficiently
1. Check the DTC again and make sure that the normal code is output.
Click here
2. Front speed sensor circuit
Click here
3. Rear speed sensor circuit
Click here
4. Stop light switch circuit
Click here
5. Check the brake actuator with Techstream. If abnormal, check the hydraulic circuit for leakage.
Click here
6. If the symptoms still occur even after the above suspected areas are inspected and proved to be normal, replace the skid control ECU.
Click here
ABS warning light abnormal (Remains on)
1. ABS warning light circuit
Click here
2. Skid control ECU
Click here
ABS warning light abnormal (Does not come on)
1. ABS warning light circuit
Click here
2. Skid control ECU
Click here
DTC of ABS check cannot be done
1. Check the DTC again and make sure that the normal code is output.
Click here
2. TC terminal circuit
Click here
3. If the symptoms still occur even after the above suspected areas are inspected and proved to be normal, replace the skid control ECU.
Click here
Sensor signal check cannot be done
1. TS and CG terminal circuit
Click here
2. Skid control ECU
Click here
VSC does not operate
1. Check the DTC again and make sure that the normal code is output.
Click here
2. IG power source circuit and ground circuit
Click here
3. Check the hydraulic circuit for leakage.
-
4. Front speed sensor circuit
Click here
5. Rear speed sensor circuit
Click here
6. Yaw rate / Deceleration sensor circuit
Click here
7. Steering sensor circuit
Click here
8. If the symptoms still occur even after the above suspected areas are inspected and proved to be normal, replace the skid control ECU.
Click here
SLIP indicator light abnormal
1. SLIP indicator light circuit
Click here
2. Skid control ECU
Click here
DTC of VSC check cannot be done
1. Check the DTC again and make sure that the normal code is output.
Click here
2. TC and CG terminal circuit
Click here
3. If the symptoms still occur even after the above suspected areas are inspected and proved to be normal, replace the skid control ECU.
Click here
VSC warning light abnormal (Remains on)
1. Check the DTC again and make sure that the normal code is output.
Click here
2. VSC warning circuit
Click here
3. If the symptoms still occur even after the above suspected areas are inspected and proved to be normal, replace the skid control ECU.
Click here
VSC warning light abnormal (Does not come on)
1. Check the DTC again and make sure that the normal code is output.
Click here
2. VSC warning circuit
Click here
3. If the symptoms still occur even after the above suspected areas are inspected and proved to be normal, replace the skid control ECU.
Click here
Brake control warning light abnormal (Remains on)
1. Check the DTC again and make sure that the normal code is output.
Click here
2. Brake control warning circuit
Click here
3. If the symptoms still occur even after the above suspected areas are inspected and proved to be normal, replace the skid control ECU.
Click here
Brake control warning light abnormal (Does not come on)
1. Check the DTC again and make sure that the normal code is output.
Click here
2. Brake control warning circuit
Click here
3. If the symptoms still occur even after the above suspected areas are inspected and proved to be normal, replace the skid control ECU.
Click here