Home › Engine / Hybrid System › 1NZ-FXE (ENGINE MECHANICAL) › ENGINE ASSEMBLY › from 2017.06
RM2170E _51 Engine / Hybrid System _057005 1NZ-FXE ENGINE MECHANICAL _0277948 ENGINE ASSEMBLY A

1NZ-FXE ENGINE MECHANICAL  ENGINE ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:

The engine assembly with transmission is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop.


HINT:

Perform "Inspection After Repairs" after replacing the engine assembly, cylinder head sub-assembly, camshaft, No. 2 camshaft, camshaft timing gear assembly, piston sub-assembly or piston ring.

w/ Canister Pump Module: Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION

w/o Canister Pump Module: Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION


PROCEDURE

Hide 82121 2.INSTALL ENGINE WIRE

a.

Connect all of the clamps and connectors and install the engine wire to the engine assembly.


Hide 3.REMOVE ENGINE STAND

a.

Using a chain block and sling device, secure the engine assembly.

NOTICE:
·

Make sure that the sling angle is correct to prevent the engine assembly and No. 1 engine hangers from being damaged or deformed.

·

Securely support the engine assembly to prevent it from turning upside down until it is secured to an engine stand.




b.

Remove the engine stand from the engine assembly.


Hide 12372A 4.INSTALL ENGINE MOUNTING INSULATOR LH

HINT:

Perform this procedure only when replacement of the engine mounting insulator LH is necessary.


a.

Temporarily install the engine mounting insulator LH with the 5 bolts.


b.
U159079E03
2.427,1.792 2.552,1.938 0.125,0.146 10 false 1 0.833,1.542 0.958,1.688 0.125,0.146 10 false 2 2.24,0.802 2.365,0.948 0.125,0.146 10 false 3 2.24,0.292 2.365,0.438 0.125,0.146 10 false 4 0.927,0.615 1.063,0.792 0.135,0.177 10 false 5

Tighten the 5 bolts in the sequence shown in the illustration.

Torque:
52 N*m (530 kgf*cm, 38 ft.*lbf)


c.

Connect the wire harness clamp.


Hide 12305 5.INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

HINT:

Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.


a.

Temporarily install the engine mounting insulator sub-assembly RH with the 3 bolts.


b.
U159112E03
1.438,1.552 1.552,1.74 0.115,0.188 10 false 1 0.813,0.927 0.938,1.073 0.125,0.146 10 false 2 2.104,0.292 2.229,0.458 0.125,0.167 10 false 3

Tighten the 3 bolts in the sequence shown in the illustration.

Torque:
52 N*m (530 kgf*cm, 38 ft.*lbf)


Hide 13405 6.INSTALL FLYWHEEL SUB-ASSEMBLY

a.

Gently place the engine assembly onto wood blocks or equivalent.

NOTICE:
·

Set the engine assembly so that it is horizontal.

·

To prevent the No. 2 oil pan sub-assembly from deforming, do not place any attachments onto the No. 2 oil pan sub-assembly of the engine assembly.

·

This step should be done while hanging the engine assembly using the sling device and chain block.





Hide 31270 7.INSTALL TRANSMISSION INPUT DAMPER ASSEMBLY

a.

Gently place the engine assembly onto wood blocks or equivalent.

NOTICE:
·

Set the engine assembly so that it is horizontal.

·

To prevent the No. 2 oil pan sub-assembly from deforming, do not place any attachments onto the No. 2 oil pan sub-assembly of the engine assembly.

·

This step should be done while hanging the engine assembly using the sling device and chain block.




b.

Install the transmission input damper assembly (See page Engine / Hybrid System>1NZ-FXE (ENGINE MECHANICAL)>REAR CRANKSHAFT OIL SEAL>INSTALLATION).


Hide 8.INSTALL ENGINE ASSEMBLY

a.
C249707E04
0.938,0.479 2.875,0.479 true 2.677,0.969 2.677,0.479 true 2.927,0.396 3.104,0.573 0.177,0.177 10 false *1 2.458,2.625 2.583,2.802 0.125,0.177 10 false A 1.198,2.5 1.333,2.677 0.135,0.177 10 false B

Make sure that the knock pins are installed to the engine assembly.

Text in Illustration
*1 Knock Pin


b.

Temporarily install the hybrid vehicle transaxle assembly to the engine assembly with the 2 bolts.

HINT:

Temporarily tighten bolt B first.



c.

Fully tighten the 2 bolts in the order of A and B.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)

Bolt Length:

45 mm (1.77 in.)


NOTICE:
·

Make sure that the wire harness or similar items are not pinched between the contact surfaces.

·

Do not forcibly pry on the hybrid vehicle transaxle assembly.

·

Make sure to align the hybrid vehicle transaxle assembly so that the input shaft of the hybrid vehicle transaxle assembly will be inserted straight into the inner splines of the transmission input damper.

·

Do not apply grease either to the spline or to the input shaft.

·

When inserting the input shaft of the hybrid vehicle transaxle assembly into the inner splines of the transmission input damper, do not shake the hybrid vehicle transaxle excessively assembly.

·

When mounting the hybrid vehicle transaxle assembly to the engine assembly, make sure to securely fit the knock pins into the knock holes.

·

When tightening the bolts, be sure that the mating surfaces of the engine and the hybrid vehicle transaxle assembly are in close contact with one another.




d.
C251452

Install the 4 bolts.

Torque:
30 N*m (301 kgf*cm, 22 ft.*lbf)

Bolt Length:

45 mm (1.77 in.)



e.

Engage the claw and install the flywheel housing side cover to the engine.


f.

Install the starter hole heat insulator to the engine assembly with the 2 bolts.

Torque:
30 N*m (301 kgf*cm, 22 ft.*lbf)

Bolt Length:

45 mm (1.77 in.)



g.

Install the drive shaft heat insulator bracket to the engine assembly with the 2 bolts.

Torque:
30 N*m (301 kgf*cm, 22 ft.*lbf)

Bolt Length:

45 mm (1.77 in.)



h.

Connect the clamp to the drive shaft heat insulator bracket.


i.

Install the drive shaft heat insulator sub-assembly to the engine assembly and drive shaft heat insulator bracket with the bolt and nut.

Torque:
18 N*m (179 kgf*cm, 13 ft.*lbf)


j.
C249795E04
1.01,2.375 0.771,2.375 true 2.51,0.5 2.833,0.5 false 2.552,0.802 2.646,0.802 2.646,0.802 2.646,0.5 false 0.583,2.281 0.76,2.438 0.177,0.156 10 true *2 2.875,0.417 3.052,0.573 0.177,0.156 10 true *1 1.844,0.448 1.99,0.604 0.146,0.156 10 false A 2.927,0.885 3.125,1.104 0.198,0.219 10 true A 1.375,2.958 1.521,3.115 0.146,0.156 10 true B

Install the 2 wire harness clamp brackets and transmission control cable support to the hybrid vehicle transaxle assembly with the 3 bolts.

Text in Illustration
*1 Wire Harness Clamp Bracket
*2 Transmission Control Cable Support

Torque:
Bolt A : 13 N*m (130 kgf*cm, 9 ft.*lbf)
Bolt B : 12 N*m (122 kgf*cm, 9 ft.*lbf)


k.

Connect the 7 clamps, 4 connectors and engine wire to the hybrid vehicle transaxle assembly with the 3 bolts.

C354335

Torque:
13 N*m (130 kgf*cm, 9 ft.*lbf)


l.
C249812

Connect the 4 clamps and No. 2 engine wire.


Hide 9.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

a.

Using a sling device and chain block, set the engine assembly with transaxle on the engine lifter.

NOTICE:
·

Place the height adjustment attachment and plate lift attachment so that the engine assembly with transaxle is level.

·

Securely support the engine assembly to prevent it from turning upside down until it is secured to an engine stand.

·

To prevent the No. 2 oil pan sub-assembly from deforming, do not place any attachments onto the No. 2 oil pan sub-assembly of the engine assembly.

·

Do not place any attachments onto the drain plug and rear cover plug of the hybrid vehicle transaxle assembly.

·

Make sure to support the engine assembly with transaxle securely to prevent it from falling.




b.

Remove the 2 bolts and 2 No. 1 engine hangers.


c.

Operate the engine lifter and lift the engine assembly with transaxle and front suspension crossmember sub-assembly to the position where the engine mounting insulator sub-assembly RH and engine mounting insulator LH can be installed.

CAUTION:

Do not raise the engine assembly with transaxle more than necessary. If the engine assembly with transaxle is raised excessively, the vehicle may also be lifted up.


NOTICE:

Make sure that the engine assembly is clear of all wiring and hoses.



d.

Operate the engine lifter and lift the engine assembly with transaxle and front suspension crossmember sub-assembly to the position where the front suspension crossmember sub-assembly can be installed.


e.

By inserting SST into the datum holes in the front suspension crossmember RH and LH alternately, temporarily install the front suspension crossmember sub-assembly with the 6 bolts.

A268628E02
2.885,1.302 1.813,1.302 false 4.302,1.302 5.156,1.302 false 2.708,2.635 3.323,2.635 false 1.656,1.219 1.823,1.375 0.167,0.156 10 false *c 1.5,3.563 1.667,3.719 0.167,0.156 10 false *a 2.677,3.563 2.844,3.719 0.167,0.156 10 false *b 4.208,3.563 4.375,3.719 0.167,0.156 10 false *a 5.375,3.563 5.542,3.719 0.167,0.156 10 false *b 5.167,1.219 5.333,1.375 0.167,0.156 10 false *c 3.344,2.563 3.646,2.719 0.302,0.156 10 false SST

Text in Illustration
*a Correct *b Incorrect
*c Datum Hole - -

SST
09670-00010  


f.

Connect the engine mounting insulator LH to the engine mounting bracket LH with the bolt and nut.

Torque:
52 N*m (530 kgf*cm, 38 ft.*lbf)


g.

Connect the engine mounting insulator sub-assembly RH to the engine assembly with the bolt and 2 nuts.

Torque:
52 N*m (530 kgf*cm, 38 ft.*lbf)


h.
U159078E03
0.583,0.573 0.719,0.719 0.135,0.146 10 false A 0.385,1.26 0.542,1.427 0.156,0.167 10 false B 0.24,1.667 0.396,1.823 0.156,0.156 10 false C 2.74,0.563 2.865,0.708 0.125,0.146 10 false A 2.938,1.26 3.063,1.406 0.125,0.146 10 false B 3.073,1.667 3.198,1.813 0.125,0.146 10 false C

Using several steps, uniformly tighten the 6 bolts.

Torque:
Bolt A : 87 N*m (887 kgf*cm, 64 ft.*lbf)
Bolt B : 151 N*m (1539 kgf*cm, 111 ft.*lbf)
Bolt C : 98 N*m (999 kgf*cm, 72 ft.*lbf)


Hide 11361J 10.INSTALL FLYWHEEL HOUSING UNDER COVER

a.

Install the flywheel housing under cover.


Hide 12.INSTALL NO. 2 ENGINE ROOM RELAY BLOCK AND NO. 2 JUNCTION BLOCK ASSEMBLY

Hide 17410 13.INSTALL FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst) (w/ Exhaust Heat Recirculation System)

Hide 17410 14.INSTALL FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst) (w/o Exhaust Heat Recirculation System)

Hide 88370 15.INSTALL COMPRESSOR WITH MOTOR ASSEMBLY

Hide 88704 16.CONNECT SUCTION HOSE SUB-ASSEMBLY

Hide 88711 17.CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE

Hide 45025D 18.CONNECT NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

Hide 45209 19.CONNECT STEERING SLIDING YOKE SUB-ASSEMBLY

Hide 45259A 20.INSTALL COLUMN HOLE COVER SILENCER SHEET

Hide 82121 22.CONNECT ENGINE WIRE (for RHD)

a.
A268668

Connect the wire harness clamp.


b.

Connect the engine wire to the engine room main wire.


c.
A268003

Connect the engine wire to the engine room relay block and junction block assembly and engage the claw.


d.

Connect the wire harness clamp and 2 connectors.


e.
A268669

Connect the ECM connector and lower the lever.

NOTICE:
·

When connecting the connector, make sure that dirt, water or other foreign matter does not become stuck between the connector and other part.

·

Make sure that the lever is securely locked.




Hide 82121 23.CONNECT ENGINE WIRE (for LHD)

a.
A268668

Connect the wire harness clamp.


b.

Connect the engine wire to the engine room main wire.


c.
A268004

Connect the engine wire to the engine room relay block and junction block assembly and engage the claw.


d.

Connect the wire harness clamp and 2 connectors.


e.
A268670

Connect the 2 wire harness clamps.


f.

Connect the ECM connector and lower the lever.

NOTICE:
·

When connecting the connector, make sure that dirt, water or other foreign matter does not become stuck between the connector and other part.

·

Make sure that the lever is securely locked.




Hide 23901 24.CONNECT FUEL TUBE SUB-ASSEMBLY

Hide 23820 25.CONNECT FUEL VAPOR FEED HOSE ASSEMBLY

a.

Connect the fuel vapor feed hose assembly and slide the clip to secure it.


Hide 26.CONNECT HEATER WATER HOSE

a.

Connect the 2 heater water hoses to the engine assembly and slide the clip to secure them.


Hide 16572D 27.CONNECT NO. 2 RADIATOR HOSE

a.

Connect the No. 2 radiator hose to the engine assembly and slide the clip to secure it.


Hide 16571C 28.CONNECT NO. 1 RADIATOR HOSE

a.
A275234E03
1.729,2.594 1.885,2.75 0.156,0.156 10 false *a 0.448,3.604 0.604,3.76 0.156,0.156 10 false *b 0.823,3.792 1.063,3.948 0.24,0.156 10 false 10° 2.167,4.073 2.479,4.229 0.313,0.156 10 false 230° 1.969,4.208 2.125,4.365 0.156,0.156 10 false *c

Connect the No. 1 radiator hose to the engine assembly and slide the clip to secure it.

Text in Illustration
*a Up
*b for LH Side
*c Do Not Position Hose Clamp Claws In This Area

HINT:

Make sure that the claws on the hose clamp are positioned as shown in the illustration.



Hide G9110 29.INSTALL INVERTER BRACKET ASSEMBLY

CAUTION:

Wear insulated gloves.


a.

Temporarily install the inverter bracket assembly with the 4 bolts.


b.
U159077E03
1.229,0.656 1.385,0.865 0.156,0.208 10 false 1 2.333,0.708 2.469,0.885 0.135,0.177 10 false 2 2.479,1.781 2.635,1.948 0.156,0.167 10 false 3 1.24,1.688 1.385,1.854 0.146,0.167 10 false 4

Tighten the 4 bolts in the sequence shown in the illustration.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


c.

Connect the earth wire with the bolt.

Torque:
8.4 N*m (85 kgf*cm, 74 in.*lbf)


d.

Install the inverter reservoir tank assembly with the 2 bolts.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


e.
A268006

Connect the 2 wire harness clamps.


f.
A268005

Connect the motor cable protector with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide G9200 32.INSTALL INVERTER WITH CONVERTER ASSEMBLY

Hide 55701J 33.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)

Hide 55701J 34.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)

Hide 55815E 35.INSTALL FRONT NO. 1 VENTILATOR SEAL (for LHD)

Hide 55815E 36.INSTALL FRONT NO. 1 VENTILATOR SEAL (for RHD)

Hide 55735B 37.INSTALL FRONT AIR SHUTTER SEAL (for LHD)

Hide 55735B 38.INSTALL FRONT AIR SHUTTER SEAL (for RHD)

Hide 55722C 39.INSTALL INNER COWL TOP TO COWL BRACE (for LHD)

Hide 55722C 40.INSTALL INNER COWL TOP TO COWL BRACE (for RHD)

Hide 41.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 47.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 49.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT

Hide 56.INSPECT FOR HYBRID TRANSAXLE FLUID LEAK

Hide 57.INSPECT FOR OIL LEAK

Hide 58.INSPECT FOR EXHAUST GAS LEAK

Hide 63.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

Hide 51441C 65.INSTALL ENGINE UNDER COVER RH (Separated Cover Type)

Hide 51442C 66.INSTALL ENGINE UNDER COVER LH (Separated Cover Type)

Hide 67.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY (Integrated Cover Type)