G1143
1.INSTALL MOTOR CABLE BRACKET
Install the motor cable bracket to the hybrid vehicle transaxle assembly with the bolt.
2.INSTALL WIRE HARNESS CLAMP BRACKET
Install the 2 wire harness clamp brackets to the hybrid vehicle transaxle assembly with the 2 bolts.
G1148
3.INSTALL MOTOR CABLE
G2148
4.INSTALL GENERATOR CABLE
12321A
5.INSTALL REAR ENGINE MOUNTING BRACKET
Install the rear engine mounting bracket with the 4 bolts in several steps.
Temporarily tighten bolt A, and then fully tighten the 4 bolts in the order of C, B, D and A.
12311A
6.INSTALL FRONT ENGINE MOUNTING BRACKET
Install the front engine mounting bracket with the 3 bolts in several steps.
Temporarily tighten bolt A, and then fully tighten the 3 bolts in the order of B, C and A.
30900
7.SUPPORT HYBRID VEHICLE TRANSAXLE ASSEMBLY
Support the hybrid vehicle transaxle assembly with a transmission jack.
30900
8.INSTALL HYBRID VEHICLE TRANSAXLE ASSEMBLY
Make sure that the knock pins are installed to the engine.
| *1 | Knock Pin |
Using an transmission jack, align the engine assembly and hybrid vehicle transaxle assembly, fit the knock pins into the knock pin holes, and tighten the 7 bolts shown in the illustration.
Make sure to align the hybrid vehicle transaxle assembly so that the input shaft of the hybrid vehicle transaxle assembly will be inserted straight into the inner splines of the transmission input damper.
When inserting the input shaft of the hybrid vehicle transaxle assembly into the inner splines of the transmission input damper, do not shake the hybrid vehicle transaxle excessively.
When mounting the hybrid vehicle transaxle assembly to the engine, make sure to securely fit the knock pins into the knock holes.
Push in the hybrid vehicle transaxle assembly so that the contact surfaces of the engine and the hybrid vehicle transaxle assembly are aligned evenly.
While mounting the hybrid vehicle transaxle assembly to the engine assembly, temporarily tighten the bolt (A), and then fully tighten the 3 bolts in the order of B, A and C.
Do not hang the hybrid vehicle transaxle assembly off of the engine if the contact surfaces of the engine and the hybrid vehicle transaxle assembly are not in full contact. The knock holes of the hybrid vehicle transaxle case may be deformed due to the excessive weight of the engine and hybrid vehicle transaxle assembly, resulting in misalignment between the engine and hybrid vehicle transaxle assembly.
12325A
9.INSTALL ENGINE MOUNTING BRACKET LH
When using the precoated bolt:
Install the engine mounting bracket LH with 3 new bolts in several steps.
Temporarily tighten bolt A, and then fully tighten the 3 bolts in the order of B, C and A.
When using the Non-precoated bolt:
Install the engine mounting bracket LH with the 3 bolts in several steps.
Temporarily tighten bolt A, and then fully tighten the 3 bolts in the order of B, C and A.
Install the engine mounting insulator LH with the bolt and nut.
When installing the engine mounting insulator, tighten the nut while holding the bolt.
12371A
10.INSTALL REAR ENGINE MOUNTING INSULATOR
51201
11.INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
12361A
12.INSTALL FRONT ENGINE MOUNTING INSULATOR
57104E
13.INSTALL FRONT CROSSMEMBER SUB-ASSEMBLY
Install the front crossmember to the body with the 4 bolts.
Install the front engine mounting insulator to the front crossmember with the 2 bolts.
Tighten the front engine mounting insulator with the bolt and nut.
52258A
14.INSTALL FRONT SUSPENSION MEMBER REAR BRACE LH
52257
15.INSTALL FRONT SUSPENSION MEMBER REAR BRACE RH
Perform the same procedure as for the LH side.
51108A
16.INSTALL REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY LH
51107A
17.INSTALL REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY RH
Perform the same procedure as for the LH side.
51425A
18.INSTALL FRONT ENGINE MOUNTING BRACKET LOWER REINFORCEMENT
11363A
19.INSTALL FLYWHEEL HOUSING SIDE COVER
Install the flywheel housing side cover.
28193
20.INSTALL STARTER HOLE INSULATOR
Install the starter hole insulator with the 2 bolts.
21.REMOVE ENGINE HANGERS
Remove the 2 bolts, No. 1 engine hanger and No. 2 engine hanger.
43040B
22.INSTALL FRONT DRIVE SHAFT HOLE SNAP RING LH
43030B
23.INSTALL FRONT DRIVE SHAFT HOLE SNAP RING RH
Perform the same procedure as for the LH side.
43420
24.INSTALL FRONT DRIVE SHAFT ASSEMBLY LH
43410
25.INSTALL FRONT DRIVE SHAFT ASSEMBLY RH
Perform the same procedure as for the LH side.
48069
26.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH
48068
27.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH
Perform the same procedure as for the LH side.
48810
28.INSTALL FRONT STABILIZER LINK ASSEMBLY LH
48820B
29.INSTALL FRONT STABILIZER LINK ASSEMBLY RH
Perform the same procedure as for the LH side.
45047
30.CONNECT TIE ROD END SUB-ASSEMBLY LH
45046
31.CONNECT TIE ROD END SUB-ASSEMBLY RH
Perform the same procedure as for the LH side.
89543
32.INSTALL FRONT SPEED SENSOR LH
89542
33.INSTALL FRONT SPEED SENSOR RH
Perform the same procedure as for the LH side.
43502H
34.INSTALL FRONT AXLE SHAFT NUT LH
43501H
35.INSTALL FRONT AXLE SHAFT NUT RH
Perform the same procedure as for the LH side.
17410
36.INSTALL FRONT EXHAUST PIPE ASSEMBLY
57533B
37.INSTALL FRONT CENTER FLOOR BRACE
51442A
38.INSTALL FRONT NO. 3 ENGINE UNDER COVER
45025D
39.CONNECT NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY
45260
40.CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY (for LHD)
45260
41.CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY (for RHD)
42. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
45259A
43.INSTALL COLUMN HOLE COVER SILENCER SHEET (for LHD)
45259A
44.INSTALL COLUMN HOLE COVER SILENCER SHEET (for RHD)
45.INSTALL WIRE HARNESS
Connect the 12 wire harness clamps and 6 connectors and install the 2 bolts.
Connect the wire harness with the clamp.
Connect the connector and lock the green-colored lock as shown in the illustration.
Wear insulated gloves when performing the procedure.
| *a | Green-colored Lock |
Install the earth wire with the bolt.
Connect the wire harness 2 clamps to the engine room junction block.
Connect the 2 connectors to the engine room junction block.
Connect the connector to the ECM with the lock lever.
Connect the 2 clamps.
G9228B
46.INSTALL WATER HOSE
Install the water hose to the hybrid vehicle transaxle assembly with the 2 hose clamps.
| *1 | Water Hose |
| *2 | No. 2 Motor Water Jacket Cover Assembly |
| *3 | Hose Clamp |
| *a | 2 to 7 mm (0.0787 to 0.276 in.) |
| *b | Alignment Mark |
| *c | Yellow Mark |
| *d | Within 45° of the center of the clamp claw |
| *e | Green Mark |
| *f | Downward |
Align the yellow mark of the water hose and the alignment mark of the No. 2 motor water jacket cover assembly.
Install the water hose upper clamp so that the center of the clamp claws is within 45° of the center of the matchmark of the No. 2 motor water jacket cover assembly as shown in the illustration.
Install the water hose so that the green mark of the water hose is within 15° of facing downward.
Connect the clamp to the wire harness clamp bracket.
G9229A
47.CONNECT NO. 5 INVERTER COOLING HOSE
G9227A
48.CONNECT NO. 3 INVERTER COOLING HOSE
16577C
49.INSTALL RADIATOR PIPE
16281
50.CONNECT NO. 4 WATER BY-PASS HOSE
16571C
51.CONNECT NO. 1 RADIATOR HOSE
G9219A
52.INSTALL INVERTER TRAY BRACKET
G92A0A
53.INSTALL INVERTER RESERVE TANK ASSEMBLY
G9200
54.INSTALL INVERTER WITH CONVERTER ASSEMBLY
55.CONNECT WATER HOSE
82112
56.CONNECT NO. 2 ENGINE ROOM WIRE
G9221
57.REMOVE INVERTER COVER
82122
58.CONNECT NO. 2 ENGINE WIRE
G1148
59.CONNECT MOTOR CABLE
G2148
60.CONNECT GENERATOR CABLE
82164
61.CONNECT FRAME WIRE
62.CHECK HIGH VOLTAGE CABLE CONNECTION
G9221
63.INSTALL INVERTER COVER
82111
64.INSTALL ENGINE ROOM MAIN WIRE
G9214
65.INSTALL NO. 1 INVERTER BRACKET
66.INSTALL AIR CLEANER HOSE ASSEMBLY
67.INSTALL AIR CLEANER CASE
17750A
68.INSTALL INLET AIR CLEANER ASSEMBLY
17705
69.INSTALL AIR CLEANER CAP SUB-ASSEMBLY
G3834
70.INSTALL SERVICE PLUG GRIP
55701J
71.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)
55701J
72.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)
55736D
73.INSTALL COWL BODY MOUNTING REINFORCEMENT LH (for LHD)
55735C
74.INSTALL COWL BODY MOUNTING REINFORCEMENT RH (for RHD)
75.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
76.ADD HYBRID TRANSAXLE FLUID
77.ADD COOLANT (for Inverter)
78.ADD COOLANT (for Engine)
79.INSPECT HYBRID TRANSAXLE FLUID
80.INSPECT FOR HYBRID TRANSAXLE FLUID LEAK
81.INSPECT FOR COOLANT LEAK (for Inverter)
82.INSPECT FOR COOLANT LEAK (for Engine)
83.INSPECT FOR EXHAUST GAS LEAK
51441
84.INSTALL NO. 1 ENGINE UNDER COVER
51442E
85.INSTALL NO. 2 ENGINE UNDER COVER
52618A
86.INSTALL FRONT LOWER BUMPER ABSORBER
51444A
87.INSTALL REAR ENGINE UNDER COVER LH
51443C
88.INSTALL REAR ENGINE UNDER COVER RH
89.INSTALL FRONT WHEELS
53301
90.INSTALL HOOD SUB-ASSEMBLY
Install the hood sub-assembly to the hood hinge assembly RH and hood hinge assembly LH with the 4 bolts.
Connect the clamp and washer hose.
53301
91.INSPECT HOOD SUB-ASSEMBLY
53301
92.ADJUST HOOD SUB-ASSEMBLY
53289A
93.INSTALL RADIATOR SUPPORT OPENING COVER
11212
94.INSTALL NO. 2 CYLINDER HEAD COVER
95.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
96.CHECK ABS SPEED SENSOR SIGNAL