After starting the engine, this DTC is stored when the engine stops without the ignition switch being operated.
Using the GTS, the conditions present when the DTC was stored can be confirmed by referring to the freeze frame data. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.
It is necessary to check if the vehicle has ran out of fuel before performing troubleshooting, as this DTC is also stored when the engine stalls due to running out of fuel.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P1603 | After monitoring for startability problems (P1604) finishes and starting the engine, with the engine running, the engine stops (the engine speed drops to 300 rpm or less) without the ignition switch being operated.
(1 trip detection logic) |
·
Air leak in intake system ·
Purge valve ·
Brake booster ·
Mass air flow meter ·
Engine coolant temperature sensor ·
Thermostat ·
Power supply circuit (purge valve, air fuel ratio sensor, fuel injector assembly, ignition coil assembly) ·
Fuel pump assembly ·
Fuel pump control circuit (low pressure side) ·
Fuel line ·
PCV valve and hose ·
Camshaft timing oil control valve ·
Knock sensor ·
Ignition system ·
Air conditioning system ·
Power steering system ·
Electrical load signal system ·
Charging system ·
Automatic transmission system ·
Park/neutral position switch assembly ·
ECM ·
Wire harness or connector ·
Engine immobiliser system |
In contrast to normal malfunction diagnosis for components, circuits and systems, DTCs P1603 is used to determine the malfunctioning area from the problem symptoms and freeze frame data when the user mentions problems such as engine stall.
As these DTCs can be stored as a result of certain user actions, even if these DTCs are output, if the customer makes no mention of problems, clear these DTCs without performing any troubleshooting and return the vehicle to the customer.
If any other DTCs are output, perform troubleshooting for those DTCs first.
Use any information from the customer problem analysis about the condition of the vehicle at the time when the problem occurred (how the engine stopped, conditions when the engine was restarted, etc.) as a reference.
| Symptom | Suspected Area |
|---|---|
| Engine vibration occurs and engine stops | Air-fuel ratio abnormal |
| Engine stops with no engine vibration | Ignition system, injection stoppage, high load from external parts |
| Engine can be started with accelerator pedal depressed | Insufficient air volume |
| Rough idling after engine started | Air-fuel ratio abnormal, abnormal combustion |
Read freeze frame data using the GTS. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.
When confirming the freeze frame data, be sure to check all 5 sets of freeze frame data (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA).
When confirming freeze frame data, if there are multiple items related to the cause of the malfunction, perform troubleshooting for all related items.
Try to operate the vehicle under the conditions recorded in the freeze frame data which were present when the malfunction occurred. Confirm the data at this time and the data when the engine is idling (engine warmed up, no load, and shift lever in D, N or neutral) and compare these data with the freeze frame data.
Inspections take into account the fact that the malfunction may not have reoccurred and place emphasis on checking the vehicle conditions present at the time when the malfunction occurred.
When performing inspections, jiggle the relevant wire harnesses and connectors in an attempt to reproduce malfunctions that do not always occur.
Using freeze frame data, narrow down the parts to be inspected according to the vehicle conditions at the time when the malfunction occurred.
If the engine stalled when the intake air volume was low (during idling or deceleration), there may be a decrease in torque due to an incorrect air-fuel ratio, etc.
If the engine stalled when the intake air volume was high (during driving or acceleration), there may be a major malfunction such as continuous misfire due to ignition stoppage, fuel injection stoppage, etc. and the torque drops to zero.
If the engine speed decreased slowly, there may have been a decrease in torque due to an air-fuel ratio that was incorrect (by approximately 20 to 30%), etc.
If the engine speed decreased rapidly, there may have been a malfunction such as when the engine misfires almost continuously due to ignition stoppage, fuel injection stoppage, etc., or when the external load increases due to an external part malfunctioning.
If the air-fuel ratio is abnormal, there may have been an intake air leak, sensor malfunction, or fuel supply problem.
If the vehicle was normal, the air volume may have been insufficient or the ignition timing may have been incorrect.
P1603 inspection flow: Narrow down the parts to be inspected according to the vehicle conditions at the time when the malfunction occurred (freeze frame data).
| Vehicle State | Engine Speed | Suspected Area | Primary Parts to Inspect | Procedure | |
|---|---|---|---|---|---|
| Idling or decelerating | Slowly decreases and engine stalls | Ignition system abnormal | Igniter abnormal | ·
Power supply circuit ·
Ignition coil assemblies ·
Spark plug |
10, 38, 52 |
| Air-fuel ratio abnormal | Air suction | ·
Intake system connections ·
Purge valve system ·
Brake booster |
5 to 9 | ||
| Sensor malfunction (value from sensor too lean) | ·
Mass air flow meter ·
Engine coolant temperature sensor ·
Air fuel ratio sensor system ·
Thermostat |
11 to 23 | |||
| Sensor malfunction (value from sensor too rich) | 39 to 51 | ||||
| Fuel supply problem | ·
Fuel pump control circuit ·
Purge valve system ·
Fuel line ·
ECM |
24 to 37 | |||
| Intake air volume insufficient | Problem with air passage | ·
Intake system connections ·
Mass air flow meter ·
Brake booster ·
PCV valve and hose ·
Purge valve system |
53 to 55 | ||
| Excessive valve overlap | ·
Camshaft timing oil control valve |
56 to 59 | |||
| Ignition timing incorrect | Does not operate as expected | ·
Knock sensor ·
Engine coolant temperature sensor ·
Mass air flow meter |
60 to 64 | ||
| Rapidly decreases and engine stalls* | Ignition and injection stops (electrical system malfunction) | Power temporarily cut | ·
Power supply circuit (fuel injector assembly (for port injection), ignition coil assembly) |
65, 66 | |
| External part malfunctioning | Increase in load | ·
Air conditioning system ·
Electrical load signal system ·
Power steering system ·
Automatic transmission system ·
Park/neutral position switch assembly |
67 to 69 | ||
| Accelerating | - | Crankshaft position sensor or VVT sensor malfunction | Power temporarily cut | ·
Check DTCs |
1 |
| Mass air flow meter | Foreign matter adhesion | ·
Mass air flow meter |
70 to 73 | ||
| Ignition and injection stops (electrical system malfunction) | Power temporarily cut | ·
Power supply circuit (fuel injector assembly (for port injection), ignition coil assembly) |
74, 75 | ||
| Fuel supply problem | Fuel leak, clog | ·
Fuel pump control circuit ·
Fuel line |
76 to 80 | ||
*: If the engine stalls immediately after the injection method is switched from port injection to direct injection, the injector driver may be malfunctioning.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Read the DTCs (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| Only DTC P1603 is output | A |
| DTCs other than P1603 are output | B |
If any DTCs other than P1603 are output, troubleshoot those DTCs first.
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA).
Immobiliser Fuel Cut is OFF.
| Result | Proceed to |
|---|---|
| Abnormal | A |
| Normal | B |
A
B
Connect the GTS to the DLC3.
Start the engine.
Idle the engine
Enter the following menus: Powertrain / Engine / Data List / Immobiliser Communication and Immobiliser Fuel Cut.
Check the Data List indication.
| Data List Item | Result |
|---|---|
| Immobiliser Communication | ON |
| Immobiliser Fuel Cut | OFF |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (w/ Entry and Start System) | B |
| NG (w/o Entry and Start System) | C |
A
B
C
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA).
| Problem Symptom | Freeze Frame Data Item | Suspected Area | Proceed to | ||
|---|---|---|---|---|---|
| Closed Throttle Position SW | Engine Speed | Total of Short FT and Long FT | |||
| When idling or decelerating, engine speed slowly decreases and engine stalls | All 5 sets of freeze frame data are ON | Decreases slowly*1 | All 5 sets of freeze frame data are +15% or more*2 | ·
Air suction ·
Sensor malfunction (value from sensor too lean) ·
Fuel supply problem |
A |
| At least 1 of the 5 sets of freeze frame data is -15% or less*3 | Sensor malfunction (value from sensor too rich) | B | |||
| All 5 sets of freeze frame data are from -15% to +15% | ·
Intake air volume insufficient ·
Ignition timing incorrect |
C | |||
| When idling or decelerating, engine speed rapidly decreases and engine stalls | Decreases rapidly*1 | - | ·
Injection stoppage, ignition stoppage ·
Load from external parts |
D | |
| When accelerating or driving at constant speed, engine stalls | At least one is OFF | - | - | ·
Sensor malfunction ·
Injection stoppage, ignition stoppage ·
Fuel supply problem |
E |
*1: A rapid decrease in engine speed may be caused by an electrical fault in the shared wiring of all or a number of cylinders, an increase in load from external parts, etc. The engine speed is considered to have decreased rapidly if either of the following conditions applies.
Otherwise, the engine speed is considered to have decreased slowly.
In the freeze frame data, the decrease in engine speed from #3 to #5 is 400 rpm or more.
In the freeze frame data, the engine speed at #5 is 120 rpm or less.
If the vehicle speed is 30 km/h or less and the difference between Engine Speed and SPD (NT) is 100 rpm or less, inspect the automatic transmission. (Depending on the rate of vehicle deceleration, the engine speed may have decreased due to the A/T lock-up release being late.)
*2: When a DTC is stored, feedback compensation increases because the air-fuel ratio is determined to be lean.
*3: When a DTC is stored, feedback compensation decreases because the air-fuel ratio is determined to be rich.
A
B
C
D
E
Check for air leakage in the intake system [vacuum hose disconnection, cracks, damaged gaskets, etc.] (See page Engine / Hybrid System>FA20 INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION).
If the accelerator pedal is released after racing the engine, the inspection is easier to perform because the vacuum inside the intake pipes increases and the air suction noise becomes louder.
If Short FT and Long FT are largely different from the normal values when idling (the intake air volume is small) and almost the same as the normal values when racing the engine (the intake air volume is high), air leakage may be present.
There is no air leakage.
OK
NG
Disconnect the purge hose (on the canister side) of the purge valve.
Start the engine.
Idle the engine.
Disconnect the connector of the purge valve.
Check if air flows through the purge valve.
Air does not flow.
Connect the connector of the purge valve.
Connect the purge hose of the purge valve.
When this inspection is performed, the MIL may illuminate. After finishing the inspection, check and clear DTCs (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA).
| Freeze Frame Data Item | Result | Suspected Area | Proceed to |
|---|---|---|---|
| Stop Light Switch | At least 1 of the 5 sets of freeze frame data is ON | Air suction from brake booster | A |
| All 5 sets of freeze frame data are OFF | - | B |
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Start the engine and warm it up until the engine coolant temperature stabilizes.
The A/C switch and all accessory switches should be off.
Idle the engine.
Using the GTS, read the value of Short FT #1 in the Data List while depressing the brake pedal.
Short FT #1 changes by +10% or less.
When air leakage from the brake booster is present, the feedback compensation increases because the air-fuel ratio becomes lean.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
A
B
C
Connect the GTS to the DLC3.
Start the engine and warm it up until the engine coolant temperature stabilizes.
The A/C switch and all accessory switches should be off.
Idle the engine.
Using the GTS, read the value of Short FT #1 in the Data List.
| Data List | Condition | Specified Condition |
|---|---|---|
| Short FT #1 + Long FT #1 | The conditions of the vehicle are matched to those present when the problem occurs | -15 to +15% |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
A
B
C
Perform ignition system On-vehicle Inspection (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION).
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA).
| Freeze Frame Data Item | Result | Suspected Area | Proceed to |
|---|---|---|---|
| Calculate Load | Below 90% of the current value of the vehicle*1 | Mass air flow meter | A |
| AFS Voltage B1S1 | 2.2 V or higher*2 | ·
Air fuel ratio sensor ·
Wire harness or connector |
B |
*1: If the mass air flow meter is malfunctioning and incorrectly measures the pressure to be less than the actual intake manifold pressure, the freeze frame data will show a low engine load value.
*2: If the air fuel ratio sensor is malfunctioning and constantly outputs a value indicating the air-fuel ratio is lean, the actual air-fuel ratio will become rich and the engine may stall.
A
B
Remove the mass air flow meter.
Check for foreign matter in the airflow passage of the mass airflow meter.
| Result | Proceed to |
|---|---|
| Visible foreign matter is not present | A |
| Visible foreign matter is present | B |
A
B
Disconnect the ECM.
Disconnect the mass air flow meter connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A33-22 (VG) - C16-5 (VG) | Always | Below 1 Ω |
| A33-29 (E2G) - C16-4 (E2G) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A33-22 (VG) or C16-5 (VG) - Body ground | Always | 10 kΩ or higher |
| A33-29 (E2G) or C16-4 (E2G) - Body ground | Always | 10 kΩ or higher |
Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
Make sure there is not an excessive amount of force applied to the wire harness.
OK
NG
Connect the GTS to the DLC3.
Start the engine and warm it up until the engine coolant temperature stabilizes.
The A/C switch and all accessory switches should be off.
Idle the engine.
Using the GTS, read the value of Calculate Load in the Data List.
| Data List | Specified Condition |
|---|---|
| Calculate Load | 90 to 110% of the current value of the vehicle |
| Result | Proceed to |
|---|---|
| Abnormal | A |
| Normal | B |
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Start the engine, turn off all accessory switches and warm up the engine until the engine coolant temperature stabilizes.
Idle the engine.
Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor.
Read the output voltage from the air fuel ratio sensor when increasing and decreasing the fuel injection volume.
| GTS Display | Specified Condition |
|---|---|
| Control the Injection Volume for A/F Sensor (+12.5%) | Air fuel ratio sensor output voltage is below 2.0 V |
| Control the Injection Volume for A/F Sensor (-12.5%) | Air fuel ratio sensor output voltage is higher than 2.4 V |
| Result | Proceed to |
|---|---|
| Abnormal | A |
| Normal | B |
The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.
A
B
Disconnect the air fuel ratio sensor connector.
Turn ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C14-2 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector
(to Air Fuel Ratio Sensor) |
Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
Make sure there is not an excessive amount of force applied to the wire harness.
OK
NG
Disconnect the ECM.
Disconnect the air fuel ratio sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A34-18 (A1A-) - C14-4 (A1A-) | Always | Below 1 Ω |
| A34-19 (A1A+) - C14-3 (A1A+) | Always | Below 1 Ω |
| A34-5 (HA1A) - C14-1 (HA1A) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A34-18 (A1A-) or C14-4 (A1A-) - Body ground | Always | 10 kΩ or higher |
| A34-19 (A1A+) or C14-3 (A1A+) - Body ground | Always | 10 kΩ or higher |
| A34-5 (HA1A) or C14-1 (HA1A) - Body ground | Always | 10 kΩ or higher |
Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
Make sure there is not an excessive amount of force applied to the wire harness.
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA).
| Freeze Frame Data Item | Result | Proceed to |
|---|---|---|
| Initial Engine Coolant Temp, Ambient Temp for A/C, Initial Intake Air Temp | Difference in temperature between each item is less than 10°C*1 | A |
| Difference in temperature between each item is 10°C or more*2 | B |
*1: A long time had elapsed after stopping the engine.
*2: A long time had not elapsed after stopping the engine.
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA).
| Freeze Frame Data Item | Result | Suspected Area | Proceed to |
|---|---|---|---|
| Initial Engine Coolant Temp, Coolant Temp, Engine Run Time | Range A | ·
Engine coolant temperature sensor ·
Thermostat |
A |
| Range B | Engine coolant temperature sensor | B | |
| Range C | - | C |
This step is not directly related to engine stall.
A
B
C
For the thermostat inspection, refer to the following procedures (See page Engine / Hybrid System>FA20 COOLING>THERMOSTAT(for Engine Coolant)>INSPECTION).
| Result | Proceed to |
|---|---|
| Abnormal | A |
| Normal | B |
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA).
| Freeze Frame Data Item | Result | Suspected Area | Proceed to |
|---|---|---|---|
| Coolant Temp | 120°C or higher | Engine coolant temperature sensor | A |
| Coolant Temp, Ambient Temp for A/C | Engine coolant temperature is lower than outside temperature by 15°C or more | Engine coolant temperature sensor | |
| Both freeze frame data items listed above | Values are other than above | - | B |
A
B
Inspect the engine coolant temperature sensor (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>ENGINE COOLANT TEMPERATURE SENSOR>INSPECTION).
OK
NG
Disconnect the ECM connector.
Disconnect the engine coolant temperature sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A36-30 (THW) - C40-2 (THW) | Always | Below 1 Ω |
| A36-29 (E1) - C40-1 (E2) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A36-30 (THW) or C40-2 (THW) - Body ground | Always | 10 kΩ or higher |
| A36-29 (E1) or C40-1 (E2) - Body ground | Always | 10 kΩ or higher |
Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
Make sure there is not an excessive amount of force applied to the wire harness.
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA).
| Freeze Frame Data Item | Result | Suspected Area | Proceed to |
|---|---|---|---|
| EVAP (Purge) VSV | At least 1 of the 5 sets of freeze frame data is not 0% | Purge valve | A |
| All 5 sets of freeze frame data are 0% | - | B |
If the purge valve is stuck closed, air-fuel ratio compensation by the purge valve is incorrectly adjusted, and then the air-fuel ratio becomes lean and the engine may stall.
A
B
Disconnect the purge hose (on the canister side) of the purge valve.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Start the engine.
Enter the following menus: Powertrain / Engine / Active Test / Activate the VSV for Evap Control.
Operate the purge valve and check the airflow.
| Activate the VSV for Evap Control | Specified Condition |
|---|---|
| ON | Air flows |
| OFF | Air does not flow |
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
| *a | VSV ON (Air flows) |
| *b | VSV OFF (Air does not flow) |
Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
A
B
Inspect the purge valve (See page Engine / Hybrid System>FA20 EMISSION CONTROL>PURGE VALVE>INSPECTION).
OK
NG
Disconnect the purge valve connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| d1-1 - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector
(to Purge valve) |
Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
Make sure there is not an excessive amount of force applied to the wire harness.
OK
NG
Disconnect the purge valve connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A36-11 (PRG) - d1-2 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A36-11 (PRG) or d1-2 - Body ground | Always | 10 kΩ or higher |
Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
Make sure there is not an excessive amount of force applied to the wire harness.
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).
NEXT
Connect the GTS to the DLC3.
Start the engine and warm it up until the engine coolant temperature stabilizes.
The A/C switch and all accessory switches should be off.
Idle the engine for 15 minutes or more.
Using the GTS, read the value of EVAP (Purge) VSV in the Data List.
| Data List | Specified Condition |
|---|---|
| EVAP (Purge) VSV | Value other than 0% is displayed |
| Result | Proceed to |
|---|---|
| Abnormal | A |
| Normal | B |
A
B
Disconnect the purge hose (on the canister side) of the purge valve.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Start the engine.
Enter the following menus: Powertrain / Engine / Active Test / Activate the VSV for Evap Control.
Operate the purge valve and check the airflow.
| Activate the VSV for Evap Control | Specified Condition |
|---|---|
| ON | Air flows |
| OFF | Air does not flow |
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
| *a | VSV ON (Air flows) |
| *b | VSV OFF (Air does not flow) |
Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
A
B
Check the ECM connector connection condition.
Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
Make sure there is not an excessive amount of force applied to the wire harness.
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump Duty.
When performing the Active Test, check for an operating sound from the fuel pump.
| Control the Fuel Pump Duty | Specified Condition |
|---|---|
| 20 or 80% | Operating sound heard |
| OFF | Operating sound not heard |
| Result | Proceed to |
|---|---|
| Abnormal | A |
| Normal | B |
Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
While performing the Active Test, make sure that there is no fuel leakage from the pipes, no signs that fuel has leaked, and no fuel smell.
If the fuel pump operating noise is abnormal, proceed to step 34.
A
B
Inspect the fuel pump assembly (See page Engine / Hybrid System>FA20 FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION).
OK
NG
Check the fuel system.
Check the fuel pump operation.
Check the fuel leaks.
Check the fuel pressure (low pressure side).
Check the fuel pressure (high pressure side).
Perform the Active Test [D-4S (Fuel Cut)].
For the fuel system On-vehicle Inspection, refer to the following procedures (See page Engine / Hybrid System>FA20 FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION).
| Result | Proceed to |
|---|---|
| Abnormal | A |
| Normal | B |
A
B
Check for foreign matter such as iron particles around the fuel pump assembly (fuel pump, fuel pump filter and inside the fuel tank), and for signs that the fuel pump was stuck.
| Result | Proceed to |
|---|---|
| There is foreign matter or signs that fuel pump was stuck | A |
| There is no foreign matter and no signs that fuel pump was stuck | B |
If there is foreign matter such as iron particles on the fuel pump, fuel filter or fuel tank, remove the foreign matter.
A
B
Check the fuel system.
Check the fuel pump operation.
Check the fuel leaks.
Check the fuel pressure (low pressure side).
Check the fuel pressure (high pressure side).
Perform the Active Test [D-4S (Fuel Cut)].
For the fuel system On-vehicle Inspection, refer to the following procedures (See page Engine / Hybrid System>FA20 FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION).
OK
NG
Perform ignition system On-vehicle Inspection (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION).
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA).
| Freeze Frame Data Item | Result | Suspected Area | Proceed to |
|---|---|---|---|
| Calculate Load | 110% or more of the current value of the vehicle*1 | Mass air flow meter | A |
| AFS Voltage B1S1 | Below 2.4 V*2 | ·
Air fuel ratio sensor ·
Harness and connector |
B |
| Both freeze frame data items listed above | Values are other than above | - | C |
*1: If the mass air flow meter is malfunctioning and incorrectly measures the intake air volume to be higher than the actual volume of air flowing through the intake manifold, the freeze frame data will show a high engine load value.
*2: As the air fuel ratio sensor output is low before the sensor warms up, the value at that time cannot be used for diagnosis. If the air fuel ratio sensor is malfunctioning and constantly outputs a value indicating the air-fuel ratio is rich, the actual air-fuel ratio will become lean and the engine may stall.
A
B
C
Remove the mass airflow meter.
Check for foreign matter in the airflow passage of the mass air flow meter.
| Result | Proceed to |
|---|---|
| Visible foreign matter is not present | A |
| Visible foreign matter is present | B |
A
B
Disconnect the mass air flow meter connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A33-22 (VG) - C16-5 (VG) | Always | Below 1 Ω |
| A33-29 (E2G) - C16-4 (E2G) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A33-22 (VG) or C16-5 (VG) - Body ground | Always | 10 kΩ or higher |
| A33-29 (E2G) or C16-4 (E2G) - Body ground | Always | 10 kΩ or higher |
Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
Make sure there is not an excessive amount of force applied to the wire harness.
OK
NG
Connect the GTS to the DLC3.
Start the engine and warm it up until the engine coolant temperature stabilizes.
The A/C switch and all accessory switches should be off.
Idle the engine.
Using the GTS, read the value of Calculate Load in the Data List.
| Data List | Specified Condition |
|---|---|
| Calculate Load | 90 to 110% of the current value of the vehicle |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Start the engine, turn off all accessory switches and warm up the engine until the engine coolant temperature stabilizes.
Idle the engine.
Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor.
Read the output voltage from the air fuel ratio sensor when increasing and decreasing the fuel injection volume.
| GTS Display | Specified Condition |
|---|---|
| Control the Injection Volume for A/F Sensor (+12.5%) | Air fuel ratio sensor output voltage is below 2.0 V |
| Control the Injection Volume for A/F Sensor (-12.5%) | Air fuel ratio sensor output voltage is higher than 2.4 V |
| Result | Proceed to |
|---|---|
| Abnormal | A |
| Normal | B |
The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.
A
B
Disconnect the air fuel ratio sensor connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C14-2 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector
(to Air Fuel Ratio Sensor) |
Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
Make sure there is not an excessive amount of force applied to the wire harness.
OK
NG
Disconnect the air fuel ratio sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A34-18 (A1A-) - C14-4 (A1A-) | Always | Below 1 Ω |
| A34-19 (A1A+) - C14-3 (A1A+) | Always | Below 1 Ω |
| A34-5 (HA1A) - C14-1 (HA1A) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A34-18 (A1A-) or C14-4 (A1A-) - Body ground | Always | 10 kΩ or higher |
| A34-19 (A1A+) or C14-3 (A1A+) - Body ground | Always | 10 kΩ or higher |
| A34-5 (HA1A) or C14-1 (HA1A) - Body ground | Always | 10 kΩ or higher |
Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
Make sure there is not an excessive amount of force applied to the wire harness.
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA).
| Freeze Frame Data Item | Result | Proceed to |
|---|---|---|
| Initial Engine Coolant Temp, Ambient Temp for A/C, Initial Intake Air Temp | Difference in temperature between each item is less than 10°C*1 | A |
| Difference in temperature between each item is 10°C or more*2 | B |
*1: A long time had elapsed after stopping the engine.
*2: A long time had not elapsed after stopping the engine.
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA).
| Freeze Frame Data Item | Result | Suspected Area | Proceed to |
|---|---|---|---|
| Initial Engine Coolant Temp, Coolant Temp, Engine Run Time | Range A | ·
Engine coolant temperature sensor ·
Thermostat |
A |
| Range B | Engine coolant temperature | B | |
| Range C | - | C |
This step is not directly related to engine stall.
A
B
C
For the thermostat inspection, refer to the following procedures (See page Engine / Hybrid System>FA20 COOLING>THERMOSTAT(for Engine Coolant)>INSPECTION).
| Result | Proceed to |
|---|---|
| Abnormal | A |
| Normal | B |
This step is not directly related to engine stall.
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA).
| Freeze Frame Data Item | Result | Suspected Area | Proceed to |
|---|---|---|---|
| Coolant Temp | 120°C or higher | Engine coolant temperature sensor | A |
| Coolant Temp, Ambient Temp for A/C | Engine coolant temperature is lower than outside temperature by 15°C or more | Engine coolant temperature sensor | |
| Both freeze frame data items listed above | Values are other than above | - | B |
A
B
For the engine coolant temperature sensor inspection, refer to the following procedures (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>ENGINE COOLANT TEMPERATURE SENSOR>INSPECTION).
| Result | Proceed to |
|---|---|
| Normal | A |
| Abnormal | B |
A
B
Disconnect the ECM connector.
Disconnect the engine coolant temperature sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A36-30 (THW) - C40-2 (THW) | Always | Below 1 Ω |
| A36-29 (E1) - C40-1 (E2) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A36-30 (THW) or C40-2 (THW) - Body ground | Always | 10 kΩ or higher |
| A36-29 (E1) or C40-1 (E2) - Body ground | Always | 10 kΩ or higher |
Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
Make sure there is not an excessive amount of force applied to the wire harness.
OK
NG
Perform ignition system On-vehicle Inspection (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION).
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA).
| Freeze Frame Data Item | Result | Suspected Area | Proceed to |
|---|---|---|---|
| Total of ISC Learning Value and ISC Feedback Value | Below 80% of the current value of the vehicle | Intake air volume insufficient | A |
| 80% or more of the current value of the vehicle | B |
A
B
Check for air leakage in the intake system [vacuum hose disconnection, cracks, damaged gaskets, etc.] (See page Engine / Hybrid System>FA20 INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION).
If the accelerator pedal is released after racing the engine, the inspection is easier to perform because the vacuum inside the intake pipes increases and the air suction noise becomes louder.
If Short FT and Long FT are largely different from the normal values when idling (the intake air volume is small) and almost the same as the normal values when racing the engine (the intake air volume is high), air leakage may be present.
There is no air leakage.
OK
NG
Check the intake system.
Inspect the brake booster assembly (for LHD) (See page Brake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER(for LHD)>INSPECTION).
Inspect the brake booster assembly (for RHD) (See page Brake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER(for RHD)>INSPECTION).
Inspect the mass air flow meter (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>MASS AIR FLOW METER>INSPECTION).
Check the PCV hose (See page Engine / Hybrid System>FA20 EMISSION CONTROL>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION).
Inspect the PCV valve (See page Engine / Hybrid System>FA20 EMISSION CONTROL>PCV VALVE>INSPECTION).
Inspect the purge valve (See page Engine / Hybrid System>FA20 EMISSION CONTROL>PURGE VALVE>INSPECTION).
| Result | Proceed to |
|---|---|
| Abnormal | A |
| Normal | B |
A
B
Connect the GTS to the DLC3.
Turn the GTS on.
Warm up the engine.
Enter the following menus: Powertrain / Engine / Active Test / Control the VVT Linear (Bank1) or Control the VVT Linear (Bank2).
When performing the Active Test, make sure the A/C is on and the shift lever is in P, N or neutral.
Check the engine speed while operating the camshaft timing oil control valve using the GTS.
| GTS Operation | Specified Condition |
|---|---|
| 0 deg (CA) | Normal engine speed |
| 36 deg (CA) | Engine idles roughly or stalls |
Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
When the results of the inspection using the Active Test are normal but the valve operating noise is abnormal, check the valve for any signs of problems.
If the camshaft timing oil control valve is stuck on, the valve overlap increases and combustion worsens due to the internal EGR which may cause rough idle or cause the engine to stall.
OK
NG
Disconnect the camshaft timing oil control valve assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C7-1 - Body ground | Ignition switch ON | 11 to 14 V |
| C24-1 - Body ground | Ignition switch ON | 11 to 14 V |
| *A | Bank 1 |
| *B | Bank 2 |
| *a | Front view of wire harness connector
(to Camshaft Timing Oil Control Valve Assembly for Intake Side) |
Disconnect the ECM connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A36-17 (OC1) - C7-2 | Always | Below 1 Ω |
| A36-16 (OC2) - C24-2 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A36-17 (OC1) or C7-2 - Body ground | Always | 10 kΩ or higher |
| A36-16 (OC2) or C24-2 - Body ground | Always | 10 kΩ or higher |
Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
Make sure there is not an excessive amount of force applied to the wire harness.
OK
NG
Connect the GTS to the DLC3.
Turn the GTS on.
Warm up the engine.
Enter the following menus: Powertrain / Engine / Active Test / Control the VVT Exhaust Linear (Bank1) or Control the VVT Exhaust Linear (Bank2).
When performing the Active Test, make sure the A/C is on and the shift lever is in P, N or neutral.
Check the engine speed while operating the camshaft timing oil control valve using the GTS.
| GTS Operation | Specified Condition |
|---|---|
| 0 deg (CA) | Normal engine speed |
| 51 deg (CA) | Engine idles roughly or stalls |
Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
When the results of the inspection using the Active Test are normal but the valve operating noise is abnormal, check the valve for any signs of problems.
If the camshaft timing oil control valve is stuck on, the valve overlap increases and combustion worsens due to the internal EGR which may cause rough idle or cause the engine to stall.
OK
NG
Disconnect the camshaft timing oil control valve assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C5-1 - Body ground | Ignition switch ON | 11 to 14 V |
| C23-1 - Body ground | Ignition switch ON | 11 to 14 V |
| *A | Bank 1 |
| *B | Bank 2 |
| *a | Front view of wire harness connector
(to Camshaft Timing Oil Control Valve Assembly for Exhaust Side) |
Disconnect the ECM connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A36-7 (OE1) - C5-2 | Always | Below 1 Ω |
| A36-5 (OE2) - C23-2 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A36-7 (OE1) or C5-2 - Body ground | Always | 10 kΩ or higher |
| A36-5 (OE2) or C23-2 - Body ground | Always | 10 kΩ or higher |
Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
Make sure there is not an excessive amount of force applied to the wire harness.
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA).
| Freeze Frame Data Item | Suspected Area | Proceed to | |
|---|---|---|---|
| IGN Advance | Knock Correct Learn Value | ||
| Differs from the current value of the vehicle by 10° or more | Less than 3° | ·
Engine coolant temperature sensor ·
Mass air flow meter ·
Knock sensor |
A |
| 3° or more | - | B | |
| Differs from the current value of the vehicle by less than 10° | - | - | |
A
B
For the engine coolant temperature sensor inspection, refer to the following procedures (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>ENGINE COOLANT TEMPERATURE SENSOR>INSPECTION).
OK
NG
Disconnect the ECM connector.
Disconnect the engine coolant temperature sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A36-30 (THW) - C40-2 (THW) | Always | Below 1 Ω |
| A36-29 (E1) - C40-1 (E2) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A36-30 (THW) or C40-2 (THW) - Body ground | Always | 10 kΩ or higher |
| A36-29 (E1) or C40-1 (E2) - Body ground | Always | 10 kΩ or higher |
Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
Make sure there is not an excessive amount of force applied to the wire harness.
OK
NG
Inspect the mass air flow meter (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>MASS AIR FLOW METER>INSPECTION).
If the intake air temperature sent to the ECM is higher than the standard due to the mass air flow meter (intake air temperature sensor) malfunctioning, the ignition timing may become delayed.
OK
NG
Connect the GTS to the DLC3.
Start the engine and warm it up until the engine coolant temperature stabilizes.
The A/C switch and all accessory switches should be off.
Idle the engine.
Using the GTS, read the value of IGN Advance and Knock Correct Learn Value in the Data List.
| Freeze Frame Data Item | Proceed to | |
|---|---|---|
| IGN Advance | Knock Correct Learn Value | |
| Differs from the current value of the vehicle by 10° or more | Less than 3° | A |
| 3° or more | B | |
| Differs from the current value of the vehicle by less than 10° | - | |
If the results of the checks performed in steps 56 to 64 were all normal and the sum of ISC Feedback Value and ISC Learning Value in the Data List is 120% of the normal value or more, check for carbon deposits in the throttle with motor body assembly. If there are carbon deposits, clean them off to finish the troubleshooting procedure.
A
B
Disconnect the fuel injector assembly connectors.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Cylinder | Tester Connection | Switch Condition | Specified Condition |
|---|---|---|---|
| No. 1 | C8-1 - Body ground | Ignition switch ON | 11 to 14 V |
| No. 2 | C30-1 - Body ground | Ignition switch ON | 11 to 14 V |
| No. 3 | C9-1 - Body ground | Ignition switch ON | 11 to 14 V |
| No. 4 | C31-1 - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector
(to Fuel Injector Assembly (for Port Injection)) |
| *b | No. 1 cylinder |
| *c | No. 2 cylinder |
| *d | No. 3 cylinder |
| *e | No. 4 cylinder |
Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
Make sure there is not an excessive amount of force applied to the wire harness.
A rapid decrease in engine speed may have been caused by a malfunction in all or multiple cylinders. (There may be an electrical malfunction in the wiring shared by all the cylinders.)
OK
NG
Perform ignition system On-vehicle Inspection (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION).
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA).
| Freeze Frame Data Item | Suspected Area | Proceed to | |
|---|---|---|---|
| A/C Signal | Air Conditioner FB Val | ||
| A/C Signal display does not change from OFF | - | Except for A/C system | A |
| A/C Signal display changes from OFF to ON*1 | Value displayed for Air Conditioner FB Val does not increase | ||
| Value displayed for Air Conditioner FB Val increases | A/C system (Automatic A/C system) | B | |
| A/C system (Manual A/C system) | C | ||
*1: Check not only the on/off state of the air conditioner but also the change in air conditioner load.
The normal value for the ISC learned value is engine displacement (liters) x 0.9.
Even if the results are normal, the power steering system and/or A/C system may have been malfunctioning. If there are no problems with other parts, inspect the power steering system and/or A/C system.
A
B
C
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA).
| Freeze Frame Data Item | Suspected Area | Proceed to | |||
|---|---|---|---|---|---|
| Electric Load Feedback Val | Difference between Engine Speed and SPD (NT) | Vehicle Speed | |||
| Electrical Load Signal display changes from OFF to ON*3, or value displayed for Electric Load Feedback Val increases*1 | Value displayed for Electric Load Val changes | - | - | Electrical load signal circuit (w/ 130 A Generator) | C |
| Electrical load signal circuit (w/ 150 A Generator) | D | ||||
| Value displayed for Electric Load Val does not change | At least 1 of the 5 sets of freeze frame data is less than 100 rpm | Less than 30 km/h | Automatic transmission system | B | |
| 30 km/h or more | - | A | |||
| All 5 sets of freeze frame data are 100 rpm or more | - | - | A | ||
| Electrical Load Signal display does not change from OFF, or value displayed for Electric Load Feedback Val does not increase | - | At least 1 of the 5 sets of freeze frame data is less than 100 rpm | Less than 30 km/h | Automatic transmission system | B |
| 30 km/h or more | - | A | |||
| All 5 sets of freeze frame data are 100 rpm or more | - | - | A | ||
*1: If the Electrical Load Signal display changes from OFF to ON, or the "Electric Load Feedback Val" increases, it probably is a malfunction due to a change in electrical load. Check the generator and the continuity and connections between the generator and ECM.
The normal value for the ISC learned value is engine displacement (liters) x 0.9.
Even if the results are normal, the electrical load signal system and/or Automatic transmission system may have been malfunctioning. If there are no problems with other parts, inspect the electrical load system and/or Automatic transmission system.
A
B
C
D
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA).
| Freeze Frame Data Item | Suspected Area | Proceed to | |
|---|---|---|---|
| Shift SW Status (P Range)
Shift SW Status (N Range) |
Neutral Position SW Signal | ||
| P and N position are both OFF in at least one data set | In D or R, NSW is ON | Park/neutral position switch assembly | A |
| In D or R, NSW is OFF | Automatic transmission system | B | |
| All 5 sets of freeze frame data are ON | - | - | C |
Even if the results are normal, the park/neutral position switch assembly and/or Automatic transmission system may have been malfunctioning. If there are no problems with other parts, inspect the park/neutral position switch assembly and/or Automatic transmission system.
A
(See pageDrivetrain>TX6A (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>INSPECTION)
B
C
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA).
| Freeze Frame Data Item | Result | Suspected Area | Proceed to |
|---|---|---|---|
| Throttle Sensor Position, Calculate Load | Calculate Load decreases while Throttle Sensor Position increases | Mass air flow meter | A |
| Calculate Load does not decrease while Throttle Sensor Position increases | - | B |
A
B
Remove the mass air flow meter (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>MASS AIR FLOW METER>REMOVAL).
Check for foreign matter in the airflow passage of the mass airflow meter.
| Result | Proceed to |
|---|---|
| Visible foreign matter is not present | A |
| Visible foreign matter is present | B |
A
B
Disconnect the mass air flow meter connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A33-22 (VG) - C16-5 (VG) | Always | Below 1 Ω |
| A33-29 (E2G) - C16-4 (E2G) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A33-22 (VG) or C16-5 (VG) - Body ground | Always | 10 kΩ or higher |
| A33-29 (E2G) or C16-4 (E2G) - Body ground | Always | 10 kΩ or higher |
Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
Make sure there is not an excessive amount of force applied to the wire harness.
OK
NG
Connect the GTS to the DLC3.
Start the engine and warm it up until the engine coolant temperature stabilizes.
The A/C switch and all accessory switches should be off.
Idle the engine.
Using the GTS, read the value of Calculate Load in the Data List.
| Data List | Specified Condition |
|---|---|
| Calculate Load | 90 to 110% of the current value of the vehicle |
OK
NG
Disconnect the fuel injector assembly connectors.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Cylinder | Tester Connection | Switch Condition | Specified Condition |
|---|---|---|---|
| No. 1 | C8-1 - Body ground | Ignition switch ON | 11 to 14 V |
| No. 2 | C30-1 - Body ground | Ignition switch ON | 11 to 14 V |
| No. 3 | C9-1 - Body ground | Ignition switch ON | 11 to 14 V |
| No. 4 | C31-1 - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector
(to Fuel Injector Assembly (for Port Injection)) |
| *b | No. 1 cylinder |
| *c | No. 2 cylinder |
| *d | No. 3 cylinder |
| *e | No. 4 cylinder |
Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
Make sure there is not an excessive amount of force applied to the wire harness.
A rapid decrease in engine speed may have been caused by a malfunction in all or multiple cylinders. (There may be an electrical malfunction in the wiring shared by all the cylinders.)
OK
NG
Perform ignition system On-vehicle Inspection (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION).
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump Duty.
When performing the Active Test, check for an operating sound from the fuel pump.
| Control the Fuel Pump Duty | Specified Condition |
|---|---|
| 25 or 80% | Operating sound heard |
| OFF | Operating sound not heard |
| Result | Proceed to |
|---|---|
| Abnormal | A |
| Normal | B |
Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
While performing the Active Test, make sure that there is no fuel leakage from the pipes, no signs that fuel has leaked, and no fuel smell.
If the fuel pump operating noise is abnormal, proceed to step 77.
A
B
Inspect the fuel pump assembly (See page Engine / Hybrid System>FA20 FUEL>FUEL PUMP>INSPECTION).
OK
NG
Check the fuel system.
Check the fuel pump operation.
Check the fuel leaks.
Check the fuel pressure.
Check the fuel pressure (for high pressure).
Perform the Active Test [D-4S (Fuel Cut)].
For the fuel system On-vehicle Inspection, refer to the following procedures (See page Engine / Hybrid System>FA20 FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION).
| Result | Proceed to |
|---|---|
| Abnormal | A |
| Normal | B |
A
B
Check for foreign matter such as iron particles around the fuel pump assembly (fuel pump, fuel pump filter and inside the fuel tank), and for signs that the fuel pump was stuck.
| Result | Proceed to |
|---|---|
| There is foreign matter or signs that fuel pump was stuck | A |
| There is no foreign matter and no signs that fuel pump was stuck | B |
If there is foreign matter such as iron particles on the fuel pump, fuel filter or fuel tank, remove the foreign matter.
A
B
Check the fuel system.
Check the fuel pump operation.
Check the fuel leaks.
Check the fuel pressure.
Check the fuel pressure (for high pressure).
Perform the Active Test [D-4S (Fuel Cut)].
For the fuel system On-vehicle Inspection, refer to the following procedures (See page Engine / Hybrid System>FA20 FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION).
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).
NEXT