35012B
1.INSTALL TRANSMISSION BREATHER HOSE SUB-ASSEMBLY
Perform this procedure only when replacement of the transmission breather hose sub-assembly is necessary.
Apply Toyota Genuine CVT fluid FE to a new O-ring, and install it to the No. 2 breather plug (CVT).
Be careful not to damage or twist the O-ring.
Install the No. 1 breather plug (CVT) and No. 2 breather plug (CVT) to the breather plug hose.
Install the transmission breather hose sub-assembly to the continuously variable transaxle assembly.
2.INSTALL STRAIGHT SCREW PLUG
Perform this procedure only when replacement of the straight screw plug is necessary.
Install the straight screw plug and a new gasket to the continuously variable transaxle assembly.
87101A
3.INSTALL NO. 1 HEATER BRACKET SUB-ASSEMBLY
Install the No. 1 heater bracket sub-assembly to the continuously variable transaxle assembly with the bolt.
Install the clamp to the No. 1 heater bracket sub-assembly.
Install the No. 1 breather plug (CVT) to the clamp.
4.INSTALL WIRE HARNESS CLAMP BRACKET
Install the 4 wire harness clamp brackets to the continuously variable transaxle assembly with the 4 bolts.
30400E
5.INSTALL CVT OIL PUMP TYPE T OIL SEAL
Ensure that there is no dirt or foreign matter on your hands and then apply MP grease to the entire periphery of the lip of a new CVT oil pump type T oil seal.
Temporarily install the CVT oil pump type T oil seal by pressing it to the installation surface of the oil pump housing by hand.
Be sure to install the CVT oil pump type T oil seal in the correct direction.
Clean the CVT oil pump type T oil seal contact surface of SST and the area around it.
| *a | Depth |
Using SST and a hammer, drive the CVT oil pump type T oil seal in evenly, until it is even with the side surface of the oil pump housing.
0 to 0.5 mm (0 to 0.0197 in.)
Drive the CVT oil pump type T oil seal in gradually, while visually checking that it is even.
After installation, confirm that the CVT oil pump type T oil seal has been driven in until it is even with the side surface of the oil pump housing.
Wipe any extra grease off with your hand.
32000A
6.INSTALL TORQUE CONVERTER ASSEMBLY
| *a | Matchmark |
| *b | Wide Groove |
| *c | Narrow Groove |
Turn the front oil pump drive gear so that the groove is at the top and place a matchmark on the transaxle housing to indicate the position of the groove.
Place the matchmark on the transaxle housing to indicate the position of the wide groove.
The matchmark position must be correct to prevent damage.
| *a | Key |
| *b | Matchmark |
Place a matchmark on the torque converter assembly so that the position of its key is clearly indicated.
| *1 | CVT Oil Pump Type T Oil Seal |
| *a | Matchmark |
Align the matchmark on the transaxle housing with the one on the torque converter assembly and engage the splines of the input shaft with the turbine runner splines.
Install the torque converter assembly to the input shaft while keeping it horizontal.
Do not damage the CVT oil pump type T oil seal.
| *1 | CVT Oil Pump Type T Oil Seal |
| *a | Matchmark |
Rotate the torque converter assembly approximately 180° and engage the splines of the stator shaft with the stator assembly.
Install the torque converter assembly to the input shaft while keeping it horizontal.
Do not damage the CVT oil pump type T oil seal.
| *1 | CVT Oil Pump Type T Oil Seal |
| *a | Matchmark |
Rotate the torque converter assembly approximately 180° again, align the matchmark on the torque converter assembly with the one on the transaxle housing and insert the key of the torque converter assembly into the groove of the front oil pump drive gear.
Install the torque converter assembly to the input shaft while keeping it horizontal.
Do not push the torque converter assembly excessively when rotating it.
Do not damage the CVT oil pump type T oil seal.
Clean the drive plate and torque converter assembly setting bolt holes.
| *a | Engine Assembly Surface |
| *b | Drive Plate Surface |
Using a vernier caliper and straightedge, measure the dimension (A) between the continuously variable transaxle assembly contact surface of the engine*a and the torque converter assembly contact surfaces of the drive plate*b.
Using a vernier caliper and straightedge, measure the dimension (B) shown in the illustration and check that the dimension (B) is more than the dimension (A), which was measured in the previous step.
B = A + 1 mm (0.0394 in.) or more
Make sure to deduct the thickness of the straightedge.
If the continuously variable transaxle assembly is installed to the engine assembly with the torque converter assembly not sufficiently inserted, the torque converter assembly may be damaged.
Do not include the thickness of the set block.
30400
7.SUPPORT CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
Using a transmission jack, support the continuously variable transaxle assembly.
Adjust the attachment of the transmission jack to securely fix the continuously variable transaxle assembly to the transmission jack.
To prevent the transaxle oil (CVT) pan sub-assembly from deforming, do not place any attachments under the transaxle oil (CVT) pan sub-assembly of the continuously variable transaxle assembly.
Using a lashing belt or a rope, fix the continuously variable transaxle assembly to the transmission jack.
30400
8.INSTALL CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
| *1 | Crankshaft |
| *2 | Torque Converter Assembly Centerpiece |
|
Clutch Spline Grease |
Apply clutch spline grease to the surface of the crankshaft that contacts the torque converter assembly centerpiece.
Toyota Genuine Clutch Spline Grease or equivalent
Approximately 1 g (0.0353 oz.)
| *1 | Knock Pin |
Confirm that the 2 knock pins are installed to the engine assembly and are not damaged.
Install the continuously variable transaxle assembly to the engine assembly with the 7 bolts.
Make sure that the wire harness or similar items are not pinched between the contact surfaces.
Do not use excess force when installing the continuously variable transaxle assembly.
When mounting the continuously variable transaxle assembly to the engine assembly, make sure to securely fit the knock pins into the knock holes.
Check that the torque converter assembly rotates.
When tightening the bolts, be sure that the mating surfaces of the engine assembly and the continuously variable transaxle assembly are in close contact with one another.
Bolt (A): Install from continuously variable transaxle assembly side
Bolt (B): Install from engine assembly side
12325A
9.INSTALL TRANSVERSE ENGINE ENGINE MOUNTING BRACKET
| *a | Temporarily Tighten |
Install the transverse engine engine mounting bracket to the continuously variable transaxle assembly with the 3 bolts in the order shown in the illustration.
10.INSTALL ENGINE MOUNTING STAY LH
| *a | Temporarily Tighten |
Install the engine mounting stay LH to the continuously variable transaxle assembly and transverse engine engine mounting bracket with the 2 bolts in the order shown in the illustration.
12372A
11.INSTALL TRANSVERSE ENGINE ENGINE MOUNTING INSULATOR
| *a | Temporarily Tighten |
Temporarily install the transverse engine engine mounting insulator to the vehicle body with the nut and 4 bolts.
Fully tighten the nut and 4 bolts in the order shown in the illustration.
Install the transverse engine engine mounting insulator to the transverse engine engine mounting bracket with the bolt and nut.
Turn the bolt while holding the nut.
32101G
12.INSTALL DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT
Clean the threads of the 6 drive plate and torque converter assembly setting bolts.
| *a | Adhesive |
Apply a few drops of adhesive to 2 or 3 threads at the tip of each of the 6 drive plate and torque converter assembly setting bolts.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
To prevent contamination by foreign matter, install immediately after applying adhesive.
Turn the crankshaft to gain access to the installation locations of the 6 drive plate and torque converter assembly setting bolts and install each drive plate and torque converter assembly setting bolt while holding the crankshaft pulley bolt with a wrench.
First install the black colored drive plate and torque converter assembly setting bolt, and then the remaining 5 silver colored drive plate and torque converter assembly setting bolts.
11361J
13.INSTALL FLYWHEEL HOUSING UNDER COVER
Install the flywheel housing under cover to the stiffening crankcase assembly.
11363A
14.INSTALL FLYWHEEL HOUSING SIDE COVER
28100
15.INSTALL STARTER ASSEMBLY (for Valeo Made Cold Area Specification Vehicles)
28100
16.INSTALL STARTER ASSEMBLY (for Valeo Made except Cold Area Specification Vehicles)
28100
17.INSTALL STARTER ASSEMBLY (for Denso Made without Stop and Start System)
12364B
18.INSTALL NO. 2 ENGINE MOVING CONTROL ROD
| *a | Temporarily Tighten |
Install the No. 2 engine moving control rod to the continuously variable transaxle assembly with the 4 bolts in the order shown in the illustration.
51201
19.INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
51108A
20.INSTALL REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY LH
51107A
21.INSTALL REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY RH
22.REMOVE ENGINE SUPPORT BRIDGE
Remove SST from the vehicle body.
Prevent SST from contacting the vehicle body or windshield glass.
Install the neck from the windshield washer jar assembly with the clip.
23.REMOVE ENGINE HANGER
Remove the 2 bolts and No. 2 engine hanger from the cylinder head.
Remove the 2 bolts and No. 1 engine hanger from the cylinder head.
Connect the No. 2 earth wire to the engine mounting insulator sub-assembly RH with the bolt.
Install the wire harness clamp bracket to the cylinder head sub-assembly with the bolt.
Install the engine wire to the wire harness clamp bracket with the nut.
Engage the 3 clamps with the wire harness clamp bracket.
24.INSTALL FRONT DRIVE SHAFT ASSEMBLIES (for TMC Made)
25.INSTALL FRONT DRIVE SHAFT ASSEMBLIES (for TMMT Made)
17410
26.INSTALL FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)
57533B
27.INSTALL FRONT FLOOR CENTER BRACE
45025D
28.INSTALL NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY
29.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
45260
30.CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY
45259A
31.INSTALL COLUMN HOLE COVER SILENCER SHEET
33823
32.INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET
Install the No. 1 transmission control cable bracket to the continuously variable transaxle assembly with the 2 bolts.
33.CONNECT WATER HOSE
Engage the 2 clamps to install the water hose to the continuously variable transaxle assembly.
Connect the water hose to the transmission oil cooler and slide the 2 hose clips to secure them.
82121
34.CONNECT ENGINE WIRE
Engage the 7 clamps to connect the engine wire to the continuously variable transaxle assembly.
| *1 | Park/Neutral Position Switch Connector | *2 | Transmission Wire Connector |
| *3 | Transmission Revolution Sensor (NIN) Connector | *4 | Transmission Revolution Sensor (NOUT) Connector |
| *5 | Oil Pressure Sensor Connector | - | - |
Connect the oil pressure sensor connector.
Connect the transmission revolution sensor (NOUT) connector.
Connect the park/neutral position switch connector.
Connect the transmission revolution sensor (NIN) connector.
Connect the transmission wire connector.
Connect the engine wire to the continuously variable transaxle assembly with the bolt.
33820B
35.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
74404A
36.INSTALL BATTERY CLAMP SUB-ASSEMBLY
Install the air battery clamp sub-assembly to the vehicle with the 3 bolts.
Engage the clamp to connect the engine wire to the battery clamp sub-assembly.
Connect the engine wire to the battery clamp sub-assembly with the bolt and nut.
89661
37.INSTALL ECM
17701
38.INSTALL AIR CLEANER CASE SUB-ASSEMBLY
39.INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE
17751
40.INSTALL NO. 1 AIR CLEANER INLET
53141F
41.INSTALL RADIATOR COVER
55701J
42.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)
55701J
43.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)
55735C
44.INSTALL COWL BODY MOUNTING REINFORCEMENT RH
55736D
45.INSTALL COWL BODY MOUNTING REINFORCEMENT LH
55735A
46.INSTALL WATER GUARD PLATE LH (for TMC Made RHD)
55737B
47.INSTALL NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL
48.INSTALL WINDSHIELD WIPER MOTOR AND LINK
49.INSTALL FRONT WHEELS
28800
50.INSTALL BATTERY
51.CONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
52.ADD ENGINE COOLANT
53.ADD COOLANT (for Intercooler)
54.ADD CONTINUOUSLY VARIABLE TRANSAXLE FLUID
55.INSPECT FOR COOLANT LEAK
56.INSPECT FOR COOLANT LEAK (for Intercooler)
57.INSPECT FOR CONTINUOUSLY VARIABLE TRANSAXLE FLUID LEAK
58.INSPECT FOR EXHAUST GAS LEAK
Click hereEngine / Hybrid System>8NR-FTS (INTAKE / EXHAUST)>EXHAUST PIPE (for 2WD)>INSTALLATION
Perform "Inspection After Repairs" after repairing or replacing the exhaust system.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
59.INSPECT SHIFT LEVER POSITION
60.ADJUST SHIFT LEVER POSITION
51443C
61.INSTALL REAR ENGINE UNDER COVER RH
51444A
62.INSTALL REAR ENGINE UNDER COVER LH
51441
63.INSTALL NO. 1 ENGINE UNDER COVER
58166
64.INSTALL FRONT FLOOR COVER LH (w/ Cover)
58165B
65.INSTALL FRONT FLOOR COVER RH (w/ Cover)
66.CHECK FOR SPEED SENSOR SIGNAL
67.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
68.RESET MEMORY
69. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART