Home › Drivetrain › K114 (MULTIDRIVE / CVT) › CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY (When Using the Engine Support Bridge) › from 2020.08
RM32H0E _52 Drivetrain _059616 K114 MULTIDRIVE / CVT _0292459 CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY(When Using the Engine Support Bridge) A

K114 MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY(When Using the Engine Support Bridge)  INSTALLATION  


PROCEDURE

Hide 35012B 1.INSTALL TRANSMISSION BREATHER HOSE SUB-ASSEMBLY

HINT:

Perform this procedure only when replacement of the transmission breather hose sub-assembly is necessary.


a.

Apply Toyota Genuine CVT fluid FE to a new O-ring, and install it to the No. 2 breather plug (CVT).

NOTICE:

Be careful not to damage or twist the O-ring.



b.

Install the No. 1 breather plug (CVT) and No. 2 breather plug (CVT) to the breather plug hose.


c.

Install the transmission breather hose sub-assembly to the continuously variable transaxle assembly.


Hide 2.INSTALL STRAIGHT SCREW PLUG

HINT:

Perform this procedure only when replacement of the straight screw plug is necessary.


a.

Install a new gasket and the straight screw plug to the continuously variable transaxle assembly.

Torque:
16.2 N*m (165 kgf*cm, 12 ft.*lbf)


Hide 35151K 3.INSTALL AUTOMATIC TRANSMISSION CASE COVER

a.

Install the automatic transmission case cover to the continuously variable transaxle assembly with the 2 clips.


Hide 32901F 4.INSTALL OIL COOLER ELBOW SUB-ASSEMBLY

a.

Install a new gasket and oil cooler elbow sub-assembly to the continuously variable transaxle assembly with the union bolt.

Torque:
22.6 N*m (230 kgf*cm, 17 ft.*lbf)

NOTICE:
·

Make sure to insert the painted end (white) of the No. 2 transmission oil cooler hose up to the spool fitting of the oil cooler elbow sub-assembly so that the marking is facing the front of the vehicle.

·

Make sure to clean and degrease the insertion part of the No. 2 transmission oil cooler hose of the oil cooler elbow sub-assembly.




b.

Install the No. 2 transmission oil cooler hose to the oil cooler elbow sub-assembly and slide the clip to secure it.


Hide 32921Y 5.INSTALL TUBE CONNECTOR

a.

Install a new O-ring to the tube connector.


b.

Install the tube connector to the continuously variable transaxle assembly.

Torque:
27 N*m (275 kgf*cm, 20 ft.*lbf)

NOTICE:
·

Make sure to insert the painted end (white) of the No. 1 transmission oil cooler hose up to the spool fitting of the tube connector so that the marking is facing the front of the vehicle.

·

Make sure to clean and degrease the insertion part of the No. 1 transmission oil cooler hose of the tube connector.




c.

Install the No. 1 transmission oil cooler hose to the tube connector and slide the clip to secure it.


Hide 6.INSTALL WIRE HARNESS CLAMP BRACKET

a.
C365123C02
1.833,4 2.219,3.719 true 2.573,3.594 2.917,3.333 false 2.917,2.083 2.167,1.292 true 0.688,1.083 1,1.083 true 0.25,0.458 0.5,0.573 true 2.938,3.198 3.177,3.396 0.24,0.198 10 false *1 0.073,0.344 0.385,0.5 0.313,0.156 10 false *2 1.01,0.99 1.24,1.167 0.229,0.177 10 true *3 1.635,3.969 1.875,4.167 0.24,0.198 10 true *1 2.958,2.052 3.198,2.25 0.24,0.198 10 false *1
*1 Wire Harness Clamp Bracket
*2 Water By-pass Hose Clamp
*3 Water Hose Clamp Bracket


Install the 3 wire harness clamp brackets to the continuously variable transaxle assembly with the 3 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


b.

Install the water by-pass hose clamp to the water hose clamp bracket.


c.

Install the water hose clamp bracket to the continuously variable transaxle assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 7.INSTALL TRANSMISSION CONTROL CABLE SUPPORT

a.

Install the transmission control cable support to the continuously variable transaxle assembly with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 30400E 8.INSTALL CVT OIL PUMP TYPE T OIL SEAL

a.

Ensure that there is no dirt or foreign matter on your hands, and then apply MP grease to the entire periphery of the lip of a new CVT oil pump type T oil seal.


b.

Temporarily install the CVT oil pump type T oil seal by pressing it to the installation surface of the oil pump housing manually.

NOTICE:

Be sure to install the CVT oil pump type T oil seal in the correct direction.



c.

Clean the CVT oil pump type T oil seal contact surface of SST and the area around it.

SST
09309-36010  


d.
C208789C01
1.802,1.792 1.802,2.469 false 1.698,2.5 2.125,2.74 0.427,0.24 10 SST 0.917,2.458 1.135,2.656 0.219,0.198 10 *a
*a 0 to 0.5 mm (0 to 0.0196 in.)


Using SST, drive the CVT oil pump type T oil seal in evenly, until it is even with the side surface of the oil pump housing.

Standard depth:

0 to 0.5 mm (0 to 0.0196 in.)


NOTICE:
·

Drive the CVT oil pump type T oil seal in gradually, while visually checking that it is even.

·

After installation, confirm that the CVT oil pump type T oil seal has been driven in until it is even with the side surface of the oil pump housing.

·

Wipe any extra grease off with your hand.



HINT:

The CVT oil pump type T oil seal should be driven in between 0 to 0.5 mm (0 to 0.0196 in.) as measured from the side surface of the oil pump housing.



Hide 32000A 9.INSTALL TORQUE CONVERTER ASSEMBLY

a.
C299234C01
1.917,0.292 1.917,0.094 1.917,0.094 2.646,0.094 false 2.708,0.031 3.021,0.229 0.313,0.198 10 false *a
*a Matchmark


Turn the front oil pump drive gear so that the wide groove is at the top and place a matchmark on the transaxle housing.

NOTICE:

Align the matchmark with the wide groove of the transaxle housing.



b.
C295655C01
1.76,0.323 2.417,0.323 false 1.344,1.99 1.688,1.99 1.688,1.99 1.688,1.594 false 2.479,0.25 2.792,0.448 0.313,0.198 10 false *a 1.146,1.917 1.458,2.115 0.313,0.198 10 false *b
*a Key
*b Matchmark


Place a matchmark on the torque converter assembly so that the position of its key is clearly indicated.


c.
C295656C01
0.427,0.135 0.802,0.135 0.802,0.135 1.25,0.385 false 0.792,0.135 1.25,0.646 false 1.375,1.969 1.896,1.969 1.896,1.969 2.688,0.865 true 1.885,1.969 2.688,1.188 true 0.24,0.052 0.552,0.25 0.313,0.198 10 false *a 1.188,1.896 1.5,2.094 0.313,0.198 10 false *1
*1 CVT Oil Pump Type T Oil Seal
*a Matchmark


Align the matchmark on the transaxle housing with the one on the torque converter assembly and engage the splines of the input shaft with the turbine runner splines.

NOTICE:
·

Install the torque converter assembly to the input shaft while keeping it horizontal.

·

Do not damage the CVT oil pump type T oil seal.




d.
C295657C01
1.25,0.375 1.417,0.198 1.417,0.198 1.646,0.198 false 0.75,2 1.042,2 1.042,2 1.25,1.542 true 1.594,1.969 1.875,1.969 1.875,1.969 2.625,0.865 true 1.875,1.969 2.656,1.229 true 0.563,1.917 0.875,2.115 0.313,0.198 10 false *a 1.708,0.125 2.021,0.323 0.313,0.198 10 false *a 1.417,1.896 1.729,2.094 0.313,0.198 10 false *1
*1 CVT Oil Pump Type T Oil Seal
*a Matchmark


Rotate the torque converter assembly approximately 180° and engage the splines of the stator shaft with the stator assembly.

NOTICE:
·

Install the torque converter assembly to the input shaft while keeping it horizontal.

·

Do not damage the CVT oil pump type T oil seal.




e.
C295658C01
0.458,0.125 0.76,0.125 0.76,0.125 1.24,0.375 true 0.76,0.125 1.25,0.646 true 1.469,1.99 1.74,1.99 1.74,1.99 2.625,0.875 true 1.729,1.99 2.656,1.229 true 0.292,0.042 0.604,0.24 0.313,0.198 10 false *a 1.292,1.917 1.604,2.115 0.313,0.198 10 false *1
*1 CVT Oil Pump Type T Oil Seal
*a Matchmark


Rotate the torque converter assembly approximately 180° again, align the matchmark on the torque converter assembly with the one on the transaxle housing and insert the key of the torque converter assembly into the groove of the oil pump drive gear.

NOTICE:
·

Install the torque converter assembly to the input shaft while keeping it horizontal.

·

Do not push the torque converter assembly excessively when rotating it.

·

Do not damage the CVT oil pump type T oil seal.




f.

Clean the drive plate and torque converter assembly setting bolt holes.


g.
C295659C01
0.656,3.104 0.656,2.26 true 0.51,1.51 0.323,0.469 0.323,0.469 0.719,0.469 true 2.385,1.302 2.594,1.302 2.594,1.302 2.594,1 false 2.385,1.885 2.594,1.885 2.594,1.885 2.729,1.573 false 0.594,3.146 0.906,3.344 0.313,0.198 10 false *b 0.781,0.406 1.094,0.604 0.313,0.198 10 false *a 2.208,1.219 2.521,1.417 0.313,0.198 10 false *a 2.219,1.813 2.531,2.01 0.313,0.198 10 false *b 2.729,0.375 2.885,0.573 0.156,0.198 10 false A
*a Engine Assembly Surface
*b Drive Plate Surface


Using a vernier caliper and straightedge, measure the dimension (A) between the continuously variable transaxle assembly contact surface of the engine assembly*a and the torque converter assembly contact surfaces of the drive plate*b.


h.
C295660E01
2.583,0.385 2.74,0.583 0.156,0.198 10 false B

Using a vernier caliper and straightedge, measure the dimension (B) shown in the illustration and check that the dimension (B) is more than the dimension (A), which was measured in the previous step.

Standard:

B = A + 1 mm (0.0394 in.) or more


NOTICE:
·

Make sure to deduct the thickness of the straightedge.

·

If the continuously variable transaxle assembly is installed to the engine assembly with the torque converter assembly not sufficiently inserted, the torque converter assembly may be damaged.

·

Do not include the thickness of the set block.




Hide 30400 10.SUPPORT CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

a.

Using a transmission jack, support the continuously variable transaxle assembly.

NOTICE:
·

Adjust the attachment of the transmission jack to securely fix the continuously variable transaxle assembly to the transmission jack.

·

To prevent the transaxle oil (CVT) pan sub-assembly from deforming, do not place any attachments under the transaxle oil (CVT) pan sub-assembly of the continuously variable transaxle assembly.

·

Using a lashing belt or a rope, fix the continuously variable transaxle assembly to the transmission jack.




Hide 30400 11.INSTALL CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

a.
C300330C02
1.552,0.938 2.146,0.667 2.146,0.667 2.615,0.667 true 2.677,0.615 2.99,0.813 0.313,0.198 10 false *a 0.99,1.083 1.302,1.281 0.313,0.198 10 false *1
*1 Crankshaft
*a Torque Converter Assembly Centerpiece


Apply clutch spline grease to the surface of the crankshaft that contacts the torque converter assembly centerpiece.

Clutch spline grease:

Toyota Genuine Clutch Spline Grease or equivalent


Maximum grease amount:

Approximately 1 g (0.0353 oz.)



b.
C298056E01
1.104,2.271 1.26,2.469 0.156,0.198 10 false A 2.417,2.146 2.729,2.344 0.313,0.198 10 false A 2.656,2.427 2.969,2.625 0.313,0.198 10 false A 0.719,2.927 0.875,3.125 0.156,0.198 10 false B 0.917,4.115 1.073,4.313 0.156,0.198 10 false B 1.292,4.385 1.448,4.583 0.156,0.198 10 false B 2.333,4.323 2.49,4.521 0.156,0.198 10 false B 2.802,4.135 2.958,4.333 0.156,0.198 10 false B

Confirm that the 2 knock pins are installed to the engine assembly and are not damaged.


c.

Install the continuously variable transaxle assembly to the engine assembly with the 8 bolts.

Torque:
Bolt (A) : 38 N*m (387 kgf*cm, 28 ft.*lbf)
Bolt (B) : 40 N*m (408 kgf*cm, 30 ft.*lbf)

NOTICE:
·

Make sure that the wire harness or similar items are not pinched between the contact surfaces.

·

Do not use excess force when installing the continuously variable transaxle assembly.

·

When mounting the continuously variable transaxle assembly to the engine assembly, make sure to securely fit the 2 knock pins into the knock holes.

·

Check that the torque converter assembly rotates.

·

When tightening the bolts, be sure that the mating surfaces of the engine assembly and the continuously variable transaxle assembly are in close contact with one another.



HINT:
·

Bolt (A): Install from continuously variable transaxle assembly side

·

Bolt (B): Install from engine assembly side




Hide 12325A 12.INSTALL TRANSVERSE ENGINE ENGINE MOUNTING BRACKET

a.
C365132C01
1.385,0.583 1.969,0.781 0.583,0.198 10 true 1 (*a), 6 2.667,0.302 2.823,0.5 0.156,0.198 10 true 4 2.396,1.24 2.552,1.438 0.156,0.198 10 true 2 1.781,1.677 1.938,1.875 0.156,0.198 10 true 3 1,1.729 1.156,1.927 0.156,0.198 10 true 5
*a Temporarily Tighten


Install the transverse engine engine mounting bracket with the 5 new bolts.

Torque:
41 N*m (418 kgf*cm, 30 ft.*lbf)


Hide 12372A 13.INSTALL TRANSVERSE ENGINE ENGINE MOUNTING INSULATOR

a.
C366442C02
0.292,0.51 0.865,0.74 0.573,0.229 10 true 1 (*a), 5 1.875,1.792 2.01,2 0.135,0.208 10 true 2 0.708,0.813 0.854,1.021 0.146,0.208 10 true 3 2.396,0.229 2.542,0.438 0.146,0.208 10 true 6 2.563,1.146 2.698,1.354 0.135,0.208 10 true 4
*a Temporarily Tighten


Temporarily install the transverse engine engine mounting insulator to the vehicle body with the nut and 4 bolts.


b.

Fully tighten the nut and 4 bolts in the order shown in the illustration.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


c.
C366441

Install the transverse engine engine mounting insulator to the transverse engine engine mounting bracket with the bolt and nut.

Torque:
44 N*m (449 kgf*cm, 32 ft.*lbf)

NOTICE:

Turn the bolt while holding the nut.



Hide 32101G 14.INSTALL DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

a.

Using SST, hold the crankshaft pulley.

SST
09213-54015  
09330-00021  

HINT:

Part number of installation bolt for SST (crankshaft pulley holding tool): 91551-00850 (quantity: 2)



b.

Clean the threads of the 6 drive plate and torque converter assembly setting bolts.


c.
A057108C45
1.708,1.906 1.948,1.5 false 1.552,1.833 1.75,2.021 0.198,0.188 10 false *a
*a Adhesive


Apply a few drops of adhesive to 2 or 3 threads at the tip of each of the 6 drive plate and torque converter assembly setting bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

In order to ensure proper installation of the 6 drive plate and torque converter assembly setting bolts, apply adhesive to the 6 drive plate and torque converter assembly setting bolts and install them within 10 minutes of adhesive application.



d.

Turn the crankshaft to gain access to the installation locations of the 6 drive plate and torque converter assembly setting bolts and install each bolt while holding the crankshaft pulley with SST.

Torque:
41 N*m (418 kgf*cm, 30 ft.*lbf)

NOTICE:

First install the black-colored bolt, and then the remaining 5 silver-colored bolts.



Hide 11361J 15.INSTALL FLYWHEEL HOUSING UNDER COVER

a.

Install the flywheel housing under cover.


Hide 11363A 16.INSTALL FLYWHEEL HOUSING SIDE COVER

Hide 28100 17.INSTALL STARTER ASSEMBLY

Hide 12364B 18.INSTALL NO. 2 ENGINE MOVING CONTROL ROD

a.
C365147C01
2.813,1.427 3.365,1.625 0.552,0.198 10 true 1 (*a), 5 1.677,0.594 1.865,0.781 0.188,0.188 10 true 2 2.833,0.677 3.021,0.865 0.188,0.188 10 true 3 1.698,1.51 1.885,1.698 0.188,0.188 10 true 4
*a Temporarily Tighten


Install the No. 2 engine moving control rod to the continuously variable transaxle assembly with the 4 bolts in the order shown in the illustration.

Torque:
44 N*m (449 kgf*cm, 32 ft.*lbf)


Hide 51201 19.INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

Hide 51108A 20.INSTALL REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY LH

Hide 51107A 21.INSTALL REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY RH

Hide 22.REMOVE ENGINE SUPPORT BRIDGE

a.

Remove SST from the vehicle body.

NOTICE:

Prevent SST from contacting the vehicle body or windshield glass.



b.

Install the neck from the windshield washer jar assembly with the clip.


Hide 23.REMOVE ENGINE HANGER

a.

Remove the 2 bolts and No. 2 engine hanger from the cylinder head.


b.

Remove the 2 bolts and No. 1 engine hanger from the cylinder head.


c.
A393422

Install the wire harness clamp bracket with the bolt.

Torque:
39 N*m (398 kgf*cm, 29 ft.*lbf)


d.

Connect the air fuel ratio sensor connector.


e.

Engage the 5 clamps.


Hide 17410 25.INSTALL FRONT EXHAUST PIPE ASSEMBLY (TWC: Front and Rear Catalyst)

Hide 57533B 26.INSTALL FRONT FLOOR CENTER BRACE

Hide 45025D 27.INSTALL NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

Hide 28.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 45260 29.CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 45259A 30.INSTALL COLUMN HOLE COVER SILENCER SHEET

Hide 33823 31.INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.

Install the No. 1 transmission control cable bracket to the continuously variable transaxle assembly with the 2 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


b.

Connect the clamp to the No. 1 transmission control cable bracket.


Hide 82121 32.CONNECT ENGINE WIRE

a.

Engage the 5 clamps to connect the engine wire to the continuously variable transaxle assembly.

C365130C03
1.167,2.083 1.375,2.281 0.208,0.198 10 true *1 1.594,2.229 1.802,2.427 0.208,0.198 10 true *2 2.344,1.063 2.521,1.24 0.177,0.177 10 true *3 6.448,0.917 6.688,1.083 0.24,0.167 10 true *4 1.385,1.229 1.594,1.396 0.208,0.167 10 true *5 4.792,1.979 5.01,2.146 0.219,0.167 10 true *6 2.063,2.042 2.24,2.219 0.177,0.177 10 true A 4.969,1.344 5.146,1.521 0.177,0.177 10 true B 5.094,1.115 5.271,1.292 0.177,0.177 10 true B
*1 Park/Neutral Position Switch Connector *2 Transmission Wire Connector
*3 Transmission Revolution Sensor (NIN) Connector *4 Transmission Revolution Sensor (NOUT) Connector
*5 Transmission Revolution Sensor (NT) Connector *6 Oil Pressure Sensor Connector



b.

Connect the engine wire to the continuously variable transaxle assembly with the 3 bolts and nut.

Torque:
Bolt (A) : 8.5 N*m (87 kgf*cm, 75 in.*lbf)
Bolt (B) : 8.0 N*m (82 kgf*cm, 71 in.*lbf)
Nut : 8.0 N*m (82 kgf*cm, 71 in.*lbf)


c.

Connect the oil pressure sensor connector.


d.

Connect the transmission revolution sensor (NOUT) connector.


e.

Connect the transmission revolution sensor (NIN) connector.


f.

Connect the transmission revolution sensor (NT) connector.


g.

Connect the transmission wire connector.


h.

Connect the park/neutral position switch connector.


Hide 16267 33.CONNECT NO. 3 WATER BY-PASS HOSE

a.

Connect the No. 3 water by-pass hose to the oil cooler, and slide the clip to secure it.

NOTICE:
·

Align each paint mark on the No. 3 water by-pass hose with each one on the oil cooler.

·

Fully insert the No. 3 water by-pass hose to the 2nd rib on each oil cooler pipe.




Hide 16282 34.CONNECT NO. 5 WATER BY-PASS HOSE

a.

Connect the No. 5 water by-pass hose to the oil cooler, and slide the clip to secure it.

NOTICE:
·

Align each paint mark on the No. 5 water by-pass hose with each one on the oil cooler.

·

Fully insert the No. 5 water by-pass hose to the 2nd rib on each oil cooler pipe.




Hide 33820B 35.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.
C365140

Install the transmission control cable assembly to the transmission control cable support with the nut.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


b.
C300679C01
3.188,0.979 3.375,1.146 0.188,0.167 10 true *a 2.854,0.375 3.031,0.521 0.177,0.146 10 true *b
*a P Position
*b N Position


Turn the control shaft lever clockwise until it stops, then turn it counterclockwise 2 notches.


c.

Install the transmission control cable assembly to the No. 1 transmission control cable bracket with a new clip.


d.

Connect the transmission control cable assembly to the control shaft lever with the nut.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 74404A 36.INSTALL BATTERY CLAMP SUB-ASSEMBLY

a.

Install the air battery clamp sub-assembly to the vehicle with the 3 bolts.

Torque:
15.4 N*m (157 kgf*cm, 11 ft.*lbf)


b.

Engage the clamp to connect the engine wire to the battery clamp sub-assembly.


c.

Connect the engine wire to the battery clamp sub-assembly with the bolt and nut.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


Hide 17701 38.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

Hide 17705 39.INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 17751 40.INSTALL NO. 1 AIR CLEANER INLET

Hide 53141F 41.INSTALL RADIATOR COVER

Hide 55701J 42.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 55735C 43.INSTALL COWL BODY MOUNTING REINFORCEMENT RH

Hide 55736D 44.INSTALL COWL BODY MOUNTING REINFORCEMENT LH

Hide 55737B 45.INSTALL NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL

Hide 46.INSTALL WINDSHIELD WIPER MOTOR AND LINK

Hide 47.INSTALL FRONT WHEELS

Hide 28800 48.INSTALL BATTERY

Hide 49.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 50.ADD ENGINE COOLANT

Hide 51.ADD CONTINUOUSLY VARIABLE TRANSAXLE FLUID

Hide 53.INSPECT FOR CONTINUOUSLY VARIABLE TRANSAXLE FLUID LEAK

Hide 54.INSPECT FOR EXHAUST GAS LEAK

Click hereEngine / Hybrid System>3ZR-FAE (INTAKE / EXHAUST)>EXHAUST PIPE>INSTALLATION

HINT:

Perform "Inspection After Repairs" after repairing or replacing the exhaust system.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


Hide 51443C 57.INSTALL REAR ENGINE UNDER COVER RH

Hide 51444A 58.INSTALL REAR ENGINE UNDER COVER LH

Hide 51441 59.INSTALL NO. 1 ENGINE UNDER COVER

Hide 62.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

Hide 64. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL

HINT:

When disconnecting and reconnecting the battery, there is an automatic leaning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART