Home › Engine / Hybrid System › 1GD-FTV (LUBRICATION) › OIL PUMP › 2017.08–2018.06
RM27T0E _51 Engine / Hybrid System _053690 1GD-FTV LUBRICATION _0260709 OIL PUMP A

1GD-FTV LUBRICATION  OIL PUMP  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.

Replaced Parts (A) Pipes Requiring New Replacement
Injector assembly (including shuffling the injector assemblies between the cylinders)
·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly


Supply pump assembly Fuel inlet pipe sub-assembly
·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Cylinder head gasket

·

Timing chain case assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly

·

Fuel inlet pipe sub-assembly



·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.

·

The injector assembly is a precision instrument. Do not use the injector assembly if it is struck or dropped.

·

Make sure foreign matter does not enter the fuel path.

·

The supply pump assembly is a precision instrument. Do not use the supply pump assembly if it is struck or dropped.

·

Hold the supply pump assembly itself during removal and installation. Do not hold the pre-stroke control valve or fuel pipe, etc.



PROCEDURE

Hide 11310 1.INSTALL TIMING CHAIN CASE ASSEMBLY AND ENGINE WATER PUMP ASSEMBLY

a.

Install a new gasket to the timing chain case assembly.


b.

Install the 4 new O-rings to the cylinder block sub-assembly and cylinder head sub-assembly.


c.

Clean and degrease the contact surfaces of the timing chain case assembly, cylinder head sub-assembly and cylinder block sub-assembly.


d.

Apply a coating of seal packing to the timing chain case assembly at the points shown in the illustration.

A339594E01
1.125,7.292 1.385,7.292 false 2.938,7.292 3.188,7.292 false 4.375,6.719 4.635,6.719 false 6.646,6.729 6.906,6.729 false 2.542,0.042 2.781,0.219 0.24,0.177 10 false *g 4.729,0.063 4.969,0.24 0.24,0.177 10 false *c 2.802,0.688 2.958,0.844 0.156,0.156 10 true A 2.323,0.833 2.479,0.99 0.156,0.156 10 true A 1.427,0.76 1.667,0.938 0.24,0.177 10 false *a 5.802,0.74 6.042,0.917 0.24,0.177 10 false *b 4.948,1.219 5.104,1.375 0.156,0.156 10 false E 3.99,1.406 4.146,1.563 0.156,0.156 10 true E 3.469,1.458 3.625,1.615 0.156,0.156 10 true D 2.479,2.01 2.635,2.167 0.156,0.156 10 true E 3.271,1.906 3.427,2.063 0.156,0.156 10 true E 5.479,4.938 5.635,5.094 0.156,0.156 10 true C 4.948,4.948 5.104,5.104 0.156,0.156 10 true C 5.5,5.375 5.656,5.531 0.156,0.156 10 false *i 2.063,5.24 2.24,5.396 0.177,0.156 10 false *h 0.698,5.615 0.854,5.771 0.156,0.156 10 false D 0.698,5.615 0.854,5.771 0.156,0.156 10 false D 1.51,6.917 1.688,7.073 0.177,0.156 10 false *e 1.427,7.208 1.604,7.365 0.177,0.156 10 false *f 2.5,5.604 2.656,5.76 0.156,0.156 10 false E 4.24,5.99 4.542,6.135 0.302,0.146 10 false C-C 3.313,6.927 3.49,7.083 0.177,0.156 10 false *c 3.229,7.219 3.406,7.375 0.177,0.156 10 false *f 4.76,6.208 4.938,6.365 0.177,0.156 10 false *c 4.667,6.635 4.844,6.792 0.177,0.156 10 false *f 6.917,6.198 7.094,6.354 0.177,0.156 10 false *c 6.938,6.646 7.115,6.802 0.177,0.156 10 false *d 6.24,6 6.823,6.146 0.583,0.146 10 false A-A, B-B 5.083,0.74 5.24,0.896 0.156,0.156 10 true B 4.51,0.75 4.667,0.906 0.156,0.156 10 true B

Text in Illustration
*a 46 mm (1.81 in.) *b 50 mm (1.97 in.)
*c 2.0 to 3.0 mm (0.0787 to 0.118 in.) *d 2.5 to 3.5 mm (0.0984 to 0.138 in.)
*e 3.0 to 4.0 mm (0.118 to 0.158 in.) *f 1.5 to 2.5 mm (0.0591 to 0.0984 in.)
*g 13 to 15 mm (0.512 to 0.591 in.) *h 9.0 to 11 mm (0.354 to 0.433 in.)
*i 31 to 33 mm (1.22 to 1.30 in.) - -

Seal packing:
for line area D:

Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent.

for line area A-A, B-B, C-C and E:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent.


Line Type and Area Seal Packing Diameter Application Area Seal Packing Application Length
Dashed Line 1.5 to 2.5 mm (0.0591 to 0.0984 in.) 2.0 to 3.0 mm (0.0787 to 0.118 in.) -
A - A 2.5 to 3.5 mm (0.0984 to 0.138 in.) 2.0 to 3.0 mm (0.0787 to 0.118 in.) 46 mm (1.81 in.)
B - B 2.5 to 3.5 mm (0.0984 to 0.138 in.) 2.0 to 3.0 mm (0.0787 to 0.118 in.) 50 mm (1.97 in.)
D 1.5 to 2.5 mm (0.0591 to 0.0984 in.) 3.0 to 4.0 mm (0.118 to 0.158 in.) -

NOTICE:
·

Using non-residue solvent, clean and remove any oil from the installation surface.

·

Install the part within 3 minutes and tighten the bolts within 10 minutes after applying seal packing.

·

Do not add engine oil for at least 2 hours after installation.

·

Do not start the engine within 2 hours after installation.




e.

Temporarily install the timing chain case assembly with the 15 bolts.

A339608E01
0.083,0.073 0.281,0.24 0.198,0.167 10 false *a 1.021,0.229 1.177,0.385 0.156,0.156 10 false A 1.104,0.531 1.26,0.688 0.156,0.156 10 false A 2.021,0.167 2.177,0.323 0.156,0.156 10 true A 2.646,0.177 2.802,0.333 0.156,0.156 10 false A 2.656,0.458 2.813,0.615 0.156,0.156 10 false A 1.667,0.76 1.823,0.917 0.156,0.156 10 true C 2.583,0.792 2.74,0.948 0.156,0.156 10 true D 1.021,0.74 1.177,0.896 0.156,0.156 10 false D 1.802,1.188 1.958,1.344 0.156,0.156 10 true D 2.625,1.031 2.781,1.188 0.156,0.156 10 true A 2.448,1.25 2.604,1.406 0.156,0.156 10 true C 0.938,0.969 1.094,1.125 0.156,0.156 10 false B 0.865,1.292 1.021,1.448 0.156,0.156 10 false B 0.729,1.729 0.885,1.885 0.156,0.156 10 false B 0.667,2.073 0.823,2.229 0.156,0.156 10 false B 0.698,2.479 0.854,2.635 0.156,0.156 10 false B 2.885,2.052 3.042,2.208 0.156,0.156 10 false B 2.781,2.479 2.938,2.635 0.156,0.156 10 false B 1.677,2.052 1.833,2.208 0.156,0.156 10 true B 2.01,1.917 2.167,2.073 0.156,0.156 10 true C 1.833,1.938 1.99,2.094 0.156,0.156 10 true C 2.198,2.052 2.354,2.208 0.156,0.156 10 true A 4.521,0.24 4.708,0.396 0.188,0.156 10 false 18 4.604,0.542 4.792,0.698 0.188,0.156 10 false 19 4.552,0.74 4.74,0.896 0.188,0.156 10 false 17 4.5,0.969 4.656,1.125 0.156,0.156 10 false 4 4.427,1.302 4.583,1.458 0.156,0.156 10 false 3 4.281,1.719 4.438,1.875 0.156,0.156 10 false 2 4.156,2.083 4.375,2.24 0.219,0.156 10 false 10 4.24,2.49 4.417,2.646 0.177,0.156 10 false 9 5.24,0.771 5.396,0.927 0.156,0.156 10 true 5 5.323,1.188 5.51,1.344 0.188,0.156 10 true 16 5.229,2.052 5.385,2.208 0.156,0.156 10 true 8 5.365,1.938 5.521,2.094 0.156,0.156 10 true 7 5.531,1.927 5.688,2.083 0.156,0.156 10 true 6 5.698,2.052 5.885,2.208 0.188,0.156 10 true 11 5.229,0.167 5.417,0.323 0.188,0.156 10 false 20 5.229,0.167 5.417,0.323 0.188,0.156 10 true 20 5.552,0.177 5.76,0.344 0.208,0.167 10 true 21 6.198,0.188 6.396,0.354 0.198,0.167 10 false 23 6.208,0.458 6.406,0.625 0.198,0.167 10 false 22 6.125,0.802 6.313,0.958 0.188,0.156 10 true 15 6.146,1.031 6.333,1.188 0.188,0.156 10 true 14 6.01,1.24 6.146,1.396 0.135,0.156 10 true 1 6.448,2.063 6.656,2.219 0.208,0.156 10 false 12 6.313,2.448 6.521,2.604 0.208,0.156 10 false 13 3.667,0.063 3.865,0.229 0.198,0.167 10 false *b 1.708,0.156 1.865,0.313 0.156,0.156 10 true A

Text in Illustration
*a Type of bolt *b Tightening

Bolt Length:
Item Length Thread Diameter
Bolt A 30 mm (1.18 in.) 8.0 mm (0.315 in.)
Bolt B 45 mm (1.77 in.) 8.0 mm (0.315 in.)
Bolt C 65 mm (2.56 in.) 8.0 mm (0.315 in.)
Bolt D 30 mm (1.18 in.) 10 mm (0.394 in.)



f.

Temporarily install a new gasket and the engine water pump assembly with the 8 bolts.


g.

Tighten the 23 bolts in the order shown in the illustration.

Torque:
for bolt A, B and C : 25 N*m (255 kgf*cm, 18 ft.*lbf)
for bolt D : 43 N*m (438 kgf*cm, 32 ft.*lbf)

NOTICE:

Check the torque of bolt 1 after tightening bolt 23.



Hide 13561 5.TEMPORARILY INSTALL NO. 1 CHAIN VIBRATION DAMPER

Hide 13506 6.INSTALL CRANKSHAFT TIMING GEAR OR SPROCKET, INJECTION PUMP DRIVE GEAR WITH NO. 1 CHAIN SUB-ASSEMBLY

Hide 13540 8.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

Hide 13559 13.INSTALL NO. 2 CHAIN TENSIONER SLIPPER

Hide 13550 14.INSTALL NO. 2 CHAIN TENSIONER ASSEMBLY

Hide 13639 17.INSTALL BALANCE SHAFT TIMING SPROCKET, BALANCE SHAFT TIMING GEAR AND NO. 3 CHAIN SUB-ASSEMBLY

Hide 11991A 18.INSTALL NO. 1 BALANCE SHAFT THRUST PLATE

Hide 13560A 19.INSTALL NO. 3 CHAIN TENSIONER ASSEMBLY

Hide 13519 20.INSTALL OIL PUMP DRIVE GEAR

a.

Install the oil pump drive gear to the crankshaft.


Hide 11302 22.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY

a.

Apply a light coat of engine oil to a new timing chain case gasket.


b.

Install the timing chain case gasket to the timing chain case assembly.


c.

Clean and degrease the contact surfaces of the timing chain cover sub-assembly and timing chain case assembly.


d.

Apply a coating of seal packing to the timing chain cover sub-assembly at the points shown in the illustration.

A339587E02
1.615,6.885 1.865,6.885 false 3.333,6.344 3.594,6.344 false 6.135,6.333 6.385,6.333 false 1.188,5.208 1.344,5.365 0.156,0.156 10 false C 2.01,6.521 2.188,6.677 0.177,0.156 10 false *a 1.917,6.813 2.115,6.99 0.198,0.177 10 false *b 3.74,5.802 3.917,5.958 0.177,0.156 10 false *a 3.635,6.271 3.833,6.448 0.198,0.177 10 false *b 6.438,6.26 6.635,6.438 0.198,0.177 10 false *b 6.385,5.802 6.563,5.958 0.177,0.156 10 false *a 3.208,5.573 3.51,5.729 0.302,0.156 10 false A-A 5.865,5.594 6.188,5.771 0.323,0.177 10 false B-B 3.313,2.563 3.49,2.719 0.177,0.156 10 false B 2.771,2.469 2.948,2.625 0.177,0.156 10 true B 2.365,1.771 2.542,1.927 0.177,0.156 10 true C 2.354,1.146 2.531,1.302 0.177,0.156 10 true A 1.865,1.156 2.042,1.313 0.177,0.156 10 false A 3.531,0.51 3.708,0.667 0.177,0.156 10 true C

Text in Illustration
*a 2.0 to 3.0 mm (0.0787 to 0.118 in.) *b 2.5 to 3.5 mm (0.0984 to 0.138 in.)

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent.


Standard seal packing diameter:

2.5 to 3.5 mm (0.0984 to 0.138 in.)


NOTICE:
·

Using non-residue solvent, clean and remove any oil from the installation surface.

·

Install the part within 3 minutes and tighten the bolts within 10 minutes after applying seal packing.

·

Do not add engine oil for at least 2 hours after installation.

·

Do not start the engine within 2 hours after installation.




e.

Temporarily install the timing chain cover sub-assembly with the 20 bolts.

A339589E02
0.073,0.052 0.281,0.219 0.208,0.167 10 false *a 0.979,0.594 1.188,0.76 0.208,0.167 10 false B 0.948,0.167 1.156,0.333 0.208,0.167 10 false A 2.896,0.146 3.104,0.313 0.208,0.167 10 false A 2.146,0.094 2.302,0.25 0.156,0.156 10 true B 2.448,0.49 2.604,0.646 0.156,0.156 10 true B 1.104,0.979 1.313,1.146 0.208,0.167 10 false B 3.115,0.729 3.323,0.896 0.208,0.167 10 false B 1.438,1.177 1.594,1.333 0.156,0.156 10 true B 1.75,1.26 1.906,1.417 0.156,0.156 10 true B 1.656,1.458 1.813,1.615 0.156,0.156 10 true B 1.313,1.521 1.469,1.677 0.156,0.156 10 true A 0.781,1.885 0.938,2.042 0.156,0.156 10 false A 0.854,2.51 1.01,2.667 0.156,0.156 10 false A 0.771,2.24 0.927,2.396 0.156,0.156 10 false A 2.698,2.521 2.854,2.677 0.156,0.156 10 false A 3.083,1.823 3.24,1.979 0.156,0.156 10 false A 2.906,2.177 3.115,2.344 0.208,0.167 10 false B 3.25,1.542 3.458,1.708 0.208,0.167 10 false B 3.177,1.135 3.385,1.302 0.208,0.167 10 false B 2.604,1.302 2.76,1.458 0.156,0.156 10 true B 3.854,0.031 4.063,0.198 0.208,0.167 10 false *b 4.177,0.156 4.385,0.323 0.208,0.167 10 false 15 4.25,0.573 4.458,0.74 0.208,0.167 10 false 14 4.375,0.969 4.583,1.135 0.208,0.167 10 false 13 4.74,1.177 4.927,1.333 0.188,0.156 10 true 12 5.073,1.271 5.26,1.427 0.188,0.156 10 true 11 4.958,1.479 5.146,1.635 0.188,0.156 10 true 10 4.625,1.521 4.813,1.677 0.188,0.156 10 true 9 4.104,1.885 4.26,2.052 0.156,0.167 10 false 8 4.094,2.229 4.25,2.396 0.156,0.167 10 false 7 4.188,2.49 4.344,2.656 0.156,0.167 10 false 6 5.427,0.115 5.615,0.271 0.188,0.156 10 true 16 6.208,0.135 6.396,0.292 0.188,0.156 10 false 17 6.021,0.573 6.208,0.729 0.188,0.156 10 false 18 6.021,0.573 6.208,0.729 0.188,0.156 10 false 18 6.406,0.708 6.594,0.865 0.188,0.156 10 false 19 5.927,1.292 6.115,1.448 0.188,0.156 10 false 1 6.479,1.135 6.667,1.292 0.188,0.156 10 false 20 6.583,1.531 6.771,1.688 0.188,0.156 10 false 2 6.406,1.823 6.594,1.979 0.188,0.156 10 false 3 6.229,2.188 6.417,2.344 0.188,0.156 10 false 4 6.01,2.521 6.198,2.677 0.188,0.156 10 false 5

Text in Illustration
*a Type of bolt *b Tightening

Bolt Length:
Item Length Thread Diameter
Bolt A 38 mm (1.50 in.) 8.0 mm (0.315 in.)
Bolt B 25 mm (0.984 in.) 8.0 mm (0.315 in.)



f.

Tighten the 20 bolts in the order shown in the illustration.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

NOTICE:

Check the torque of bolt 1 after tightening bolt 20.



Hide 12101 24.INSTALL OIL PAN SUB-ASSEMBLY

a.

Clean and degrease the contact surfaces of the oil pan sub-assembly and cylinder block sub-assembly.


b.
A339755

Apply seal packing in a continuous line as shown in the illustration.

Text in Illustration
V100135

Seal Packing

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

3.5 to 4.5 mm (0.138 to 0.177 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the oil pan sub-assembly within 3 minutes and tighten the bolts and nuts within 10 minutes after applying seal packing.

·

Do not add engine oil within 2 hours after installation.

·

Do not start the engine for at least 2 hours after installation.




c.
A339700E02
0.865,1.552 1.01,1.698 0.146,0.146 10 true A 0.979,1.969 1.125,2.115 0.146,0.146 10 true A 1.229,1.99 1.375,2.135 0.146,0.146 10 true A 1.719,1.99 1.865,2.135 0.146,0.146 10 true A 2.26,1.979 2.427,2.135 0.167,0.156 10 true A 2.385,1.75 2.563,1.927 0.177,0.177 10 true A 2.417,1.5 2.594,1.667 0.177,0.167 10 true A

Install the oil pan sub-assembly to the cylinder block sub-assembly with the 23 bolts and 2 nuts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:

Check the torque of all nuts and bolts labeled A again.



Hide 12102A 26.INSTALL NO. 2 OIL PAN SUB-ASSEMBLY

a.

Clean and degrease the contact surfaces of the No. 2 oil pan sub-assembly and cylinder block sub-assembly.


b.
A339754

Apply seal packing in a continuous line as shown in the illustration.

Text in Illustration
V100135

Seal Packing

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

3.5 to 4.5 mm (0.138 to 0.177 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the No. 2 oil pan sub-assembly within 3 minutes and tighten the bolts and nuts within 10 minutes after applying seal packing.

·

Do not add engine oil within 2 hours after installation.

·

Do not start the engine for at least 2 hours after installation.




c.

Install the No. 2 oil pan sub-assembly to the oil pan sub-assembly with the 11 bolts and 2 nuts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 11201 27.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

a.

Apply a light coat of engine oil to the O-ring of the camshaft position sensor.


b.

Install a new cylinder head cover gasket, No. 2 cylinder head cover gasket and 2 camshaft bearing cap oil hole gaskets to the cylinder head cover sub-assembly.


c.

Clean and degrease the contact surfaces of the cylinder head cover sub-assembly and cylinder head sub-assembly.


d.

Apply seal packing as shown in the illustration.

A339583E02
0.51,1.729 0.51,2.271 true 1.396,1.094 1.396,2.26 true 2.448,1.521 2.99,1.521 true 4.271,0.51 5.292,0.51 true 6.073,1.115 6.604,1.115 true 1.344,4.51 1.344,5.042 true 2.198,4.396 2.198,4.927 true 0.75,3.292 0.667,3.292 0.667,3.292 0.448,3.708 true 0.802,0.323 1.031,0.5 0.229,0.177 10 true *a 0.427,2.323 0.667,2.51 0.24,0.188 10 false *1 1.865,0.344 2.104,0.51 0.24,0.167 10 true *a 0.281,1 0.5,1.177 0.219,0.177 10 true *c 2.354,1.021 2.531,1.167 0.177,0.146 10 true *b 1.313,2.281 1.51,2.438 0.198,0.156 10 false *2 3.042,1.448 3.292,1.625 0.25,0.177 10 false *3 4.052,0.427 4.292,0.625 0.24,0.198 10 false *3 5.938,0.125 6.115,0.271 0.177,0.146 10 true *d 6.708,0.542 6.885,0.688 0.177,0.146 10 false *a 6.646,1.031 6.844,1.188 0.198,0.156 10 false *4 6.74,1.677 6.917,1.823 0.177,0.146 10 true *a 5.927,1.99 6.104,2.135 0.177,0.146 10 true *d 0.896,3.51 1.115,3.688 0.219,0.177 10 true *a 1.875,3.521 2.052,3.667 0.177,0.146 10 true *a 2.438,4.146 2.646,4.323 0.208,0.177 10 true *b 0.333,4.146 0.521,4.323 0.188,0.177 10 true *c 1.26,5.073 1.469,5.24 0.208,0.167 10 true *2 2.115,4.938 2.313,5.125 0.198,0.188 10 true *3 0.792,3.219 1,3.375 0.208,0.156 10 false *1

Text in Illustration
*1 Timing Chain Cover Sub-assembly *2 Timing Chain Case Assembly
*3 Cylinder Head Sub-assembly *4 No. 3 Camshaft Bearing Cap
*a Seal Diameter: 3.0 to 6.0 mm (0.118 to 0.236 in.) *b Application Width: 7.0 mm (0.276 in.)
*c Application Width: 9.0 mm (0.354 in.) *d Application Width: 11.0 mm (0.433 in.)

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

3.0 to 6.0 mm (0.118 to 0.236 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the cylinder head cover sub-assembly within 3 minutes and tighten the bolts within 10 minutes after applying seal packing.

·

Do not add engine oil for at least 2 hours after installation.

·

Do not start the engine within 2 hours after installation.




e.
A339609E02
0.052,0 0.271,0.177 0.219,0.177 10 false 20 0.531,0 0.76,0.188 0.229,0.188 10 false 15 0.823,0 1.063,0.188 0.24,0.188 10 false 11 1.271,0.042 1.5,0.24 0.229,0.198 10 false 9 1.792,0.042 1.979,0.198 0.188,0.156 10 false 13 2.354,0 2.542,0.156 0.188,0.156 10 false 17 3.135,0 3.323,0.156 0.188,0.156 10 false 19 0.031,0.698 0.188,0.844 0.156,0.146 10 false 5 0.49,0.927 0.677,1.083 0.188,0.156 10 true 6 0.5,1.365 0.688,1.521 0.188,0.156 10 true 3 1.073,1.375 1.26,1.531 0.188,0.156 10 true 1 1.719,1.365 1.906,1.521 0.188,0.156 10 true 2 2.302,1.365 2.49,1.521 0.188,0.156 10 true 4 2.865,1.5 3.052,1.656 0.188,0.156 10 true 7 0.146,2 0.344,2.167 0.198,0.167 10 true 18 0.396,1.99 0.583,2.146 0.188,0.156 10 false 14 0.771,1.979 0.958,2.135 0.188,0.156 10 false 10 1.344,1.906 1.531,2.063 0.188,0.156 10 false 8 1.906,1.917 2.094,2.073 0.188,0.156 10 false 12 2.458,1.927 2.646,2.083 0.188,0.156 10 false 16 2.927,1.896 3.115,2.052 0.188,0.156 10 false 21

Tighten the 14 bolts, 4 nozzle holder clamp seats, 2 nuts and camshaft position sensor in the order shown in the illustration.

Text in Illustration
V100135

Bolt
V100136

Nut
V100137

Nozzle Holder Clamp Seat

Torque:
10 N*m (107 kgf*cm, 7 ft.*lbf)

NOTICE:
·

When reusing the camshaft position sensor, check the O-rings.

·

Make sure that the O-ring is not cracked or jammed when installing it on the cylinder head cover sub-assembly.

·

Replace with a new part if it is dropped or if it receives a strong impact.

·

Check the torque of bolts 1 to 4 again.




Hide 23670 29.TEMPORARILY INSTALL INJECTOR ASSEMBLY

Hide 12501 30.INSTALL GENERATOR BRACKET SUB-ASSEMBLY

Hide 16575C 32.INSTALL NO. 1 WATER HOSE CLAMP BRACKET

Hide 88451B 35.INSTALL VISCOUS HEATER CRANKSHAFT PULLEY (w/ Viscous Heater)

Hide 16620 36.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

a.

Install the V-ribbed belt tensioner assembly to the timing chain cover sub-assembly with 3 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 16603 37.INSTALL NO. 1 IDLER PULLEY SUB-ASSEMBLY

a.

Install the No. 1 idler pulley sub-assembly to the generator bracket sub-assembly with the bolt.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 16207 41.INSTALL NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 15407 42.TEMPORARILY INSTALL TURBO OIL INLET PIPE SUB-ASSEMBLY

Hide 17141 43.TEMPORARILY INSTALL EXHAUST MANIFOLD WITH TURBOCHARGER SUB-ASSEMBLY

Hide 17141 46.TIGHTEN EXHAUST MANIFOLD WITH TURBOCHARGER SUB-ASSEMBLY

Hide 87101 48.INSTALL NO. 1 VISCOUS HEATER BRACKET SUB-ASSEMBLY (w/ Viscous Heater)

Hide 12203 61.INSTALL PCV PIPE (for Cold Area Specification Vehicles)

Hide 12261 62.INSTALL PCV HOSE (except Cold Area Specification Vehicles)

Hide 88431 63.INSTALL NO. 1 COMPRESSOR MOUNTING BRACKET

Hide 23701 66.INSTALL NO. 1 AND NO. 2 INJECTION PIPE SUB-ASSEMBLY

Hide 23701 68.TIGHTEN NO. 1 AND NO. 2 INJECTION PIPE SUB-ASSEMBLY

Hide 23760 70.INSTALL NOZZLE LEAKAGE PIPE ASSEMBLY

Hide 23770 74.INSTALL NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY

Hide 22803 80.INSTALL FUEL INJECTION PUMP COVER SUB-ASSEMBLY

Hide 25800 85.INSTALL NO. 1 EGR COOLER AND NO. 2 EGR VALVE ASSEMBLY WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY

Hide 16209 86.INSTALL NO. 4 WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 16206B 90.INSTALL NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 106.INSTALL ENGINE WIRE

Hide 12633 108.INSTALL NO. 3 ENGINE COVER BRACKET

a.

Install the No. 3 engine cover bracket to the No. 2 engine cover bracket and engine cover bracket with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)