Home › Engine / Hybrid System › 1GD-FTV (ENGINE MECHANICAL) › ENGINE UNIT › 2018.06–2020.08
RM27T0E _51 Engine / Hybrid System _053665 1GD-FTV ENGINE MECHANICAL _0260522 ENGINE UNIT A

1GD-FTV ENGINE MECHANICAL  ENGINE UNIT  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.

Replaced Parts (A) Pipes Requiring New Replacement
Injector assembly (including shuffling the injector assemblies between the cylinders)
·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly


Supply pump assembly Fuel inlet pipe sub-assembly
·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Cylinder head gasket

·

Timing chain case assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly

·

Fuel inlet pipe sub-assembly



·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.

·

The injector assembly is a precision instrument. Do not use the injector assembly if it is struck or dropped.

·

The supply pump assembly is a precision instrument. Do not use the supply pump assembly if it is struck or dropped.

·

The common rail assembly is a precision instrument. Do not use the common rail assembly if it is struck or dropped.

·

Hold the supply pump assembly itself during removal and installation. Do not hold the pre-stroke control valve or fuel pipe, etc.

·

Hold the common rail assembly itself during removal and installation. Do not hold the pressure discharge valve or fuel pressure sensor, etc.

·

Make sure foreign matter does not enter the fuel path.



PROCEDURE

Hide 12633 1.REMOVE NO. 3 ENGINE COVER BRACKET (w/o Urea SCR System)

Hide 12632 2.REMOVE NO. 2 ENGINE COVER BRACKET (w/o Urea SCR System)

Hide 82121 3.REMOVE ENGINE WIRE

Hide 17360A 4.REMOVE AIR TUBE ASSEMBLY (w/o Urea SCR System)

Hide 77246C 5.REMOVE FUEL MAIN TUBE SUPPORT (w/ Urea SCR System)

Hide 26100G 6.REMOVE DIESEL THROTTLE BODY ASSEMBLY

Hide 16278 7.REMOVE NO. 2 WATER BY-PASS PIPE

Hide 25625 16.REMOVE EGR VALVE BRACKET

Hide 16206B 18.REMOVE NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 27148A 19.REMOVE CONNECTING WIRE

a.
A343587

Disconnect the connector from the common rail assembly.


b.

Detach the 2 clamps and remove the connecting wire from the hose bracket.


Hide 25601 20.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY

a.
A428763C01
0.094,0.135 0.406,0.292 0.313,0.156 10 false *A 0.115,2.552 0.427,2.708 0.313,0.156 10 false *B
*A w/o Urea SCR System
*B w/ Urea SCR System


Remove the 4 nuts, bolt and No. 1 EGR pipe sub-assembly from the exhaust manifold, electric EGR control valve assembly and No. 1 vacuum transmitting pipe sub-assembly.


b.

Remove the 2 gaskets from the exhaust manifold and electric EGR control valve assembly.


c.
A354081

Using an E8 "TORX" socket wrench, remove the 2 stud bolts from the exhaust manifold.


Hide 16209 22.REMOVE NO. 4 WATER BY-PASS PIPE SUB-ASSEMBLY

a.
A424502

w/ Urea SCR System:

Slide the 2 clamps and remove the No. 17 water by-pass hose from the No. 1 EGR pipe sub-assembly and No. 4 water by-pass pipe sub-assembly.


b.
A354082E01
2.823,1.771 2.823,2.104 2.823,2.104 3,2.104 true 2.854,4.167 2.854,3.833 2.854,3.833 3.031,3.833 true 1.708,0.74 1.115,0.229 1.115,0.229 0.938,0.229 true 1.427,1.615 0.938,2.052 0.938,2.052 0.75,2.052 true 1.708,3.24 1.115,2.729 1.115,2.729 0.938,2.729 true 2.667,0.458 2.552,0.125 2.552,0.125 2.375,0.125 true 2.729,3 2.573,2.604 2.573,2.604 2.396,2.604 true 3.031,2.01 3.26,2.208 0.229,0.198 10 true *1 0.719,0.135 0.906,0.292 0.188,0.156 10 false *2 2.156,0.031 2.344,0.219 0.188,0.188 10 true *3 0.542,1.958 0.729,2.115 0.188,0.156 10 false *4 0.052,0.021 0.302,0.208 0.25,0.188 12 false *A 0.052,2.469 0.302,2.656 0.25,0.188 12 false *B 3.063,3.75 3.25,3.906 0.188,0.156 10 true *1 0.719,2.635 0.906,2.792 0.188,0.156 10 false *2 2.177,2.51 2.365,2.667 0.188,0.156 10 true *3

Slide the clamp and disconnect the No. 6 water by-pass hose from the No. 4 water by-pass pipe sub-assembly.

Text in Illustration
*A for Cold Area Specification Vehicles
*B except Cold Area Specification Vehicles
*1 No. 6 Water By-pass Hose
*2 No. 7 Water By-pass Hose
*3 Water Hose
*4 No. 11 Water By-pass Hose


c.

Slide the clamp and disconnect the No. 7 water by-pass hose from the No. 4 water by-pass pipe sub-assembly.


d.

Slide the clamp and disconnect the water hose from the No. 2 EGR valve assembly.


e.

for Cold Area Specification Vehicles:

Detach the clamp and disconnect the No. 11 water by-pass hose from the No. 2 fuel pipe.


f.

Remove the 2 bolts and No. 4 water by-pass pipe sub-assembly from the intake manifold.


Hide 25800 23.REMOVE NO. 1 EGR COOLER AND NO. 2 EGR VALVE ASSEMBLY WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY

Hide 11409 24.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 23812D 25.REMOVE NO. 2 FUEL PIPE

a.
A343499

Slide the clamp and disconnect the No. 1 fuel hose from the No. 2 fuel pipe.


b.

Remove the bolt and No. 2 fuel pipe from the manifold stay.


Hide 26.REMOVE WIRING HARNESS CLAMP BRACKET

Hide 22803 28.REMOVE FUEL INJECTION PUMP COVER SUB-ASSEMBLY

Hide 23243B 29.REMOVE FUEL PUMP MOTOR WIRE

Hide 23804D 30.REMOVE NO. 4 FUEL PIPE SUB-ASSEMBLY

Hide 23273H 31.REMOVE NO. 2 FUEL HOSE

Hide 23271H 32.REMOVE NO. 1 FUEL HOSE

Hide 23804C 33.REMOVE FUEL INLET PIPE SUB-ASSEMBLY

Hide 23770 34.REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY

Hide 36.REMOVE WIRING HARNESS CLAMP BRACKET

Hide 38.REMOVE WIRING HARNESS CLAMP BRACKET

a.
A354083

for LHD:

Remove the 3 bolts and 3 wiring harness clamp brackets from the cylinder head cover sub-assembly.


b.
A421445

for RHD:

Remove the 2 bolts and 2 wiring harness clamp brackets from the cylinder head cover sub-assembly.


Hide 23701 39.REMOVE NO. 1 AND NO. 2 INJECTION PIPE SUB-ASSEMBLY

Hide 23810A 40.REMOVE COMMON RAIL ASSEMBLY

Hide 19871 41.REMOVE NO. 1 GLOW PLUG CONNECTOR

Hide 19850 42.REMOVE GLOW PLUG ASSEMBLY

Hide 43.REMOVE HOSE BRACKET

a.
A343501

Remove the 2 bolts and hose bracket from the cylinder head sub-assembly.


Hide 23300 45.REMOVE FUEL FILTER ASSEMBLY

a.
A347297

Remove the 2 nuts and fuel filter assembly from the cylinder block sub-assembly.


Hide 16025 46.REMOVE NO. 5 WATER BY-PASS PIPE SUB-ASSEMBLY

a.
A343503

Remove the 3 bolts, No. 5 water by-pass pipe sub-assembly and gasket from the cylinder block sub-assembly.


Hide 88431 47.REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET

a.
A354085

Remove the 4 bolts and No. 1 compressor mounting bracket from the cylinder block sub-assembly, timing chain case assembly and timing chain cover sub-assembly.


Hide 89422C 48.REMOVE ENGINE COOLANT TEMPERATURE SENSOR

Hide 12261 49.REMOVE PCV HOSE (except Cold Area Specification Vehicles)

Hide 12229 50.REMOVE PCV PIPE (for Cold Area Specification Vehicles)

Hide 51.REMOVE WATER BY-PASS HOSE (w/ Urea SCR System)

Hide 16282 52.REMOVE NO. 5 WATER BY-PASS HOSE

a.
A347299

Slide the 2 clamps and disconnect the No. 5 water by-pass hose from the No. 1 injector holder and water outlet sub-assembly.


b.

Detach the clamp and remove the No. 5 water by-pass hose from the No. 1 water hose clamp bracket.


Hide 16281 53.DISCONNECT NO. 4 WATER BY-PASS HOSE

a.
A347300

Slide the clamp and disconnect the No. 4 water by-pass hose from the No. 1 injector holder.


Hide 17168 55.REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

Hide 89467B 56.REMOVE AIR FUEL RATIO SENSOR (w/o Urea SCR System)

Hide 17167 57.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 89463C 59.DISCONNECT NO. 1 NITROGEN OXIDES SENSOR (w/ Urea SCR System)

Hide 25051 62.REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

Hide 89463C 63.REMOVE NO. 1 NITROGEN OXIDES SENSOR (w/ Urea SCR System)

Hide 12361 64.REMOVE FRONT ENGINE MOUNTING INSULATOR RH

a.
A354086

Disconnect the No. 3 vacuum transmitting hose sub-assembly from the front engine mounting insulator RH.


b.

Remove the nut and front engine mounting insulator RH from the front No. 1 engine mounting bracket RH.


Hide 16268 66.REMOVE NO. 1 WATER BY-PASS PIPE

a.

Remove the 3 bolts, No. 1 water by-pass pipe and gasket from the timing chain cover sub-assembly.

A428764C01
2.74,0.104 7.094,1.708 4.354,1.604 0.188,0.146 0.5,0.302 0.313,0.156 10 false *A 2.813,0.156 3.125,0.313 0.313,0.156 10 false *B 2.823,0.354 3.135,0.51 0.313,0.156 10 false *C 5.021,0.177 5.333,0.333 0.313,0.156 10 false *D
*A except Cold Area Specification Vhecles *B for Cold Area Specification Vhecles
*C w/o Urea SCR System *D w/ Urea SCR System



Hide 16284 67.DISCONNECT NO. 1 AND NO. 2 TURBO WATER HOSE

Hide 87101 68.REMOVE NO. 1 VISCOUS HEATER BRACKET SUB-ASSEMBLY (w/ Viscous Heater)

a.
A354088

Remove the 4 bolts and No. 1 viscous heater bracket sub-assembly from the cylinder block sub-assembly and timing chain cover sub-assembly.


Hide 17293 69.REMOVE TURBOCHARGER STAY

a.
A353383

Remove the 3 bolts, nut and the turbocharger stay.


Hide 15407 71.REMOVE TURBO OIL INLET PIPE SUB-ASSEMBLY

Hide 17201 72.REMOVE TURBOCHARGER SUB-ASSEMBLY

a.
A425658C02
0.042,0.063 0.354,0.219 0.313,0.156 10 false *A 0.063,2.313 0.375,2.469 0.313,0.156 10 false *B
*A w/o Urea SCR System
*B w/ Urea SCR System


Remove the 3 nuts and turbocharger sub-assembly.


b.

Remove the gasket from the exhaust manifold.


Hide 16207 74.REMOVE NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

a.
A343506

Slide the clamp and disconnect the No. 3 water by-pass hose from the water outlet sub-assembly.


b.

Remove the 2 bolts and No. 2 water by-pass pipe sub-assembly from the engine water pump assembly and water inlet.


Hide 16304 75.REMOVE WATER OUTLET SUB-ASSEMBLY

a.
A347303E01
0.048,0.035 0.310,0.211 0.262,0.176 12 *A 0.048,2.436 0.308,2.613 0.259,0.176 12 *B

Remove the 4 bolts, 2 nuts and water outlet sub-assembly from the timing chain cover sub-assembly.

Text in Illustration
*A w/ DPF
*B w/o DPF


b.

Remove the gasket from the timing chain cover sub-assembly.


Hide 16603 76.REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY

Hide 16620 77.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

Hide 25804A 78.REMOVE VACUUM SWITCHING VALVE SUB-ASSEMBLY (for Engine Mounting)

Hide 25706 79.REMOVE NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY

a.
A456453

Disconnect the No. 1 vacuum transmitting hose sub-assembly from the vacuum pump assembly.


b.
A457925

Disconnect the No. 2 vacuum transmitting hose sub-assembly from the No. 3 vacuum transmitting pipe sub-assembly.


c.

Remove the 3 bolts and No. 1 vacuum transmitting pipe sub-assembly from the cylinder head sub-assembly.


Hide 25707 80.REMOVE NO. 2 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY

a.
A354091

Remove the 2 bolts and No. 2 vacuum transmitting pipe sub-assembly from the cylinder block sub-assembly and oil pan sub-assembly.


Hide 25708 81.REMOVE NO. 3 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY

a.
A428765C01
0.115,0.146 0.427,0.302 0.313,0.156 10 false *A 0.135,2.49 0.448,2.646 0.313,0.156 10 false *B
*A w/o Urea SCR System
*B w/ Urea SCR System


Disconnect the No. 4 vacuum transmitting hose sub-assembly from the No. 3 vacuum transmitting pipe sub-assembly.


b.

Remove the 2 bolts and No. 3 vacuum transmitting pipe sub-assembly from the cylinder head sub-assembly and cylinder block sub-assembly.


Hide 25709E 82.REMOVE NO. 4 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY

a.
A354093

Remove the bolt and No. 4 vacuum transmitting pipe sub-assembly from the cylinder block sub-assembly.


Hide 88451B 83.REMOVE VISCOUS HEATER CRANKSHAFT PULLEY (w/ Viscous Heater)

Hide 16575C 86.REMOVE NO. 1 WATER HOSE CLAMP BRACKET

a.
A347304

Remove the bolt and No. 1 water hose clamp bracket from the timing chain case assembly.